四配位Ti掺杂有机杂化介孔分子筛的直接合成与表征

以三嵌段共聚物P123为模板剂,NaCl为助剂,1,2-二(三乙氧基甲硅烷基)乙烷为硅源,在水热合成过程中引入钛源,原位一步合成了四配位Ti掺杂在骨架内的SBA-15型有机杂化介孔分子筛(Ti-PMO).利用小角X射线衍射、透射电子显微镜以及低温N2物理吸附等手段表征了Ti-PMO的晶体结构和织构性能,并利用紫外-可见漫反射光谱考察了钛源种类、钛源预水解时间、溶液酸性以及Si/Ti摩尔比对Ti存在形态的影响.研究结果表明,通过精确调控Ti-PMO的合成条件,可使钛源水解产生的低聚中间体与硅源水解产生的低聚中间体充分接触并发生共缩聚,引入的Ti原子能够最终随着水解的氧化硅物种自组装生成有序介孔结构的SBA-15型分子筛,并以四配位形式均匀分布于PMO骨架中.以Cl2TiCp2为钛源,盐酸浓度为0.18mol/L时,钛源预水解6h后加入硅源,在Si/Ti摩尔比大于20时可以得到骨架内四配位Ti掺杂的高度有序介孔结构有机杂化分子筛,其具有良好的热稳定性及水热稳定性.     

Ti掺杂SBA-15负载Ni基催化剂用于木质素衍生物定向加氢脱氧转化

本研究通过在SBA-15分子筛骨架内掺杂Ti物种并负载Ni纳米颗粒合成了“金属-酸”双功能催化剂(Ni/Ti-SBA-15)。Ti的掺杂不仅提高了催化剂酸性位点的数量,还促进了Ni纳米颗粒在载体上的高度分散。在绿色、温和条件下实现了香兰素到2-甲氧基-4-甲基苯酚(MMP)高效转化,目标产物选择性高达96.46%。此外,Ni/Ti-SBA-15催化剂价格低廉,制备工艺简单,这项工作为制备廉价高效催化剂提供了新的思路,有利于实现生物质衍生物的绿色、低成本升级转化。     

金属改性SBA-15应用于乙醇水蒸气重整制氢的研究

采用水热法将Ce金属引入SBA-15骨架,合成一系列Ce-SBA-15（Si/Ce=40,20,10）载体,再通过浸渍法制得Co/Ce-SBA-15催化剂.利用XRD、UV-Vis、FT-IR、H₂-TPR、N₂吸附-脱附等手段对催化剂进行表征,并用于乙醇水蒸汽重整制氢反应（ESR）,考察载体骨架中Ce金属对催化剂结构和性能的影响.结果表明,水热法制备可使得Ce离子进入到SBA-15分子筛骨架,合成的载体仍保持SBA-15特有的介孔结构.与Co/SBA-15催化剂相比,基于铈的储放氧功能,Ce的加入提高了活性金属分散度,降低了反应积碳的生成,改善了催化剂稳定性.适量铈与钴的协同作用,提高了钴物种的分散度,降低了钴的烧结程度,催化剂Co/Ce-SBA-15（Si/Ce=20）具有良好的催化活性,乙醇转化率为96.6%,H₂选择性达到75.5%,反应后积碳率仅为5.6%.     

Ti掺杂苯基与乙基桥连的有序介孔有机硅的制备及其催化环己烯氧化反应

分别采用1,4-(双乙氧基硅烷)苯(1,4-BTEB)和1,2-三乙氧基硅基乙烷(1,2-BTESE)作为有机硅源,正硅酸乙酯(TEOS)为无机硅源,钛酸四丁酯(TBOT)为钛源,以Pluronic EO20PO70EO20(P123)为模板剂在酸性环境下水热合成制备了Ti掺杂的有机-无机有序介孔有机硅材料Ti-SBA-15-ben和Ti-SBA-15-et.同时,在合成过程中加入H2O2作为配合剂调节钛源水解速度,制备得到Ti-SBA-15-ben-H和Ti-SBA-15-et-H.采用FT-IR、DR UV-Vis、N2物理吸附、XRD、TG-DSC、TEM等方法对制备的样品进行了表征.结果表明:合成过程中加入H2O2制备的苯基桥连有机硅杂化材料具有较好的疏水性能,其骨架中活性4价位钛含量高,结构有序性最好.在以叔丁基过氧化氢(TBHP)为氧源的环己烯氧化反应中对制备的催化材料进行了对比评价,结果表明:Ti-SBA-15-ben-H表现出最高的催化活性,其催化的反应以环氧化产物为主,环己烯的转化率为26.9%,环氧选择性为32.8%,T i-SBA-15-et催化的反应以烯丙位氧化产物2-环己烯-1-酮为主,环己烯的转化率为8.5%,2-环己烯-1-酮选择性为41.2%.     

Ti-Co-SBA-15的制备、表征及其选择氧化催化性能

以钛酸丁酯为钛源,分子筛SBA-15为载体,采用水热法合成了一系列不同载钛量的Ti-SBA-15分子筛,用浸渍法将钴负载于其骨架结构上,得到Ti-Co-SBA-15催化剂。采用X射线、N2吸附-脱附、漫反射紫外-可见光谱和傅里叶变换红外光谱等方法对样品进行了表征,并考察了催化剂在温和条件下对叔丁基甲苯氧气氧化反应中的催化性能。结果表明,所制备的催化剂样品具有较大的比表面积和孔径,钛、钴以四配位体存在,具有较高的催化活性和选择性,可获得较高的对叔丁基苯甲醛收率。     

磺酸基功能化的有序SBA-15-SO3H介孔分子筛的合成及其在苯酚叔丁基化反应中的应用

通过一步法合成了SBA-15-SO3H介孔分子筛,用XRD,TEM,低温N2吸附和吡啶吸附红外光谱等方法进行了表征,并研究了其在苯酚叔丁基化反应中的催化性能.结果表明,SBA-15-SO3H保持了母体SBA-15高度有序的六方介孔结构,具有较强的酸性和热稳定性,且在苯酚叔丁基化反应中表现较好的催化活性和2,4-二叔丁基苯酚选择性.     

Ti-Co-SBA-15的制备、表征及其选择氧化催化性能

以钛酸丁酯为钛源,分子筛SBA-15为载体,采用水热法合成了一系列不同载钛量的Ti-SBA-15分子筛,用浸渍法将钴负载于其骨架结构上,得到Ti-Co-SBA-15催化剂。采用X射线、N₂吸附-脱附、漫反射紫外-可见光谱和傅里叶变换红外光谱等方法对样品进行了表征,并考察了催化剂在温和条件下对叔丁基甲苯氧气氧化反应中的催化性能。结果表明,所制备的催化剂样品具有较大的比表面积和孔径,钛、钴以四配位体存在,具有较高的催化活性和选择性,可获得较高的对叔丁基苯甲醛收率。     

混合超分子液晶模板法合成六方介孔相含钛氧化硅

采用混合十六烷基三甲基溴化铵（CTAB）与不同碳链的脂肪胺（CnNH2n＋3, n=8,10,12,14,16）作模板,在四甲基氢氧化胺为碱源的条件下,合成了具有六方介孔结构的含钛氧化硅Ti MCM 41分子筛材料. XRD和TEM测试表明所合成材料具有高度的长程有序结构,样品的N2吸附/脱附等温线表明,高度有序的Ti MCM 41材料展示了毛细凝聚的陡峭台阶和狭窄的介孔孔径分布.对反应物配比中Ti/Si比、脂肪胺碳链长度n对六方介孔相结构的影响进行了研究,实验发现当Ti/Si< 0.15和n< 16时,均可获得具有六方介孔结构的含钛氧化硅Ti MCM 41;而当Ti/Si≥0.15或n >16时,产物将分别发生从六方向无定形态或从六方向层状介孔相结构的转移,从混合表面活性剂的堆积参数对这种相转移现象进行了分析.     

In/SBA-15催化剂的一步法制备及其在水介质中Barbier反应中的应用

采用金属In的石蜡溶液浸渍载体, 一步法制备具有介孔结构的In/SBA-15催化剂. 在水介质中苯甲醛与烯丙基溴的Barbier反应中, 发现负载量为w(In)＝13%的In/SBA-15的催化活性显著高于金属In颗粒催化剂, 而选择性相似, 目标产物1-苯基-3-丁烯基-1-醇的得率可达89.2%. In/SBA-15的高活性主要归因于In活性位在SBA-15上的高分散, 以及规整的介孔结构有利于反应物分子的扩散. 同时, 金属In与SBA-15间较强的相互作用也可稳定In活性位, 显示出良好的应用潜力.     

天然丝光沸石多步脱铝-钛化制备钛硅分子筛

以优选的天然丝光沸石为原料, 采用多步脱铝-钛化法合成钛硅分子筛, 利用 X 射线粉末衍射、紫外-可见光谱、电感耦合等离子体原子发射光谱、N2 吸附-脱附法以及氨程序升温脱附等手段对其进行了表征, 并考察了它在苯乙烯氧化反应中的催化性能. 结果表明, 该方法可成功地将 Ti 同晶取代到天然丝光沸石的骨架中, 其 Si/Ti 达到 79, 且能稳定地保持天然丝光沸石的结构. 该钛硅分子筛在以 H2O2 水溶液为氧化剂的苯乙烯氧化反应中表现有良好的催化活性, 是商业 TS-1 催化剂的 75%, 具有一定的应用前景.     

Ti-SBA-15介孔材料用于磷酸化肽的高效富集

结合基质辅助激光解吸飞行时间质谱(MALDI-TOF MS)检测技术,考察了Ti-SBA-15介孔材料对β-酪蛋白酶解产物中磷酸化肽的选择性富集性能。实验结果显示,含Ti和Si物质的量比为0.08的Ti-SBA-15介孔材料可选择性地对β-酪蛋白酶解产物中的磷酸化肽进行选择性富集;对于β-酪蛋白和牛血清白蛋白物质的量比为1:100的蛋白质酶解混合液,Ti-SBA-15仍能实现对其磷酸化肽的有效富集。上述结果表明,作为一种多孔、高比表面积的磷酸化多肽的选择性吸附材料,Ti-SBA-15有望在磷酸化蛋白质组的分析中得到广泛的应用。     

Adsorption of benzene onto mesoporous silicates modified by titanium

Mesoporous molecular sieve SBA-15 modified by titanium has been utilized for removing organic pollutants, such as benzene, from air. Titanium was impregnated inside SBA-15 by wetness impregnation after synthesis of SBA-15 (impregnation method) or was doped into the SBA-15 framework by the direct addition of Ti precursor into the sol during synthesis (doping method). In the breakthrough curves for gas-phase benzene adsorption, Ti addition into SBA-15 resulted in the enhancement of benzene adsorption capacity, depending on Ti loading amounts. An increase in adsorption temperature remarkably reduced the benzene adsorption capacity, indicating that the interaction between benzene and the materials was weak.     

Direct synthesis of ordered mesoporous ZSM-5 zeolites from in situ crystallization of carbonaceous SBA-15

Two types of ordered mesoporous ZSM-5 zeolites with different mesopores were synthesized by a two-step method. First,carbonaceous SBA-15 was produced by in situ carbonization of SBA-15/P123 composite. Then the obtained SBA-15/C composite was transformed into crystallized mesoporous ZSM-5 by impregnation TPAOH followed by steam-assisted crystallization. The final calcined samples synthesized with typical SBA-15/P123 precursor showed a wormlike morphology with the mean mesopore size of 4.6 nm, while samples synthesized with the addition of trimethylbenzene as swelling agent in the precursor exhibited the morphology of microsphere with the mesopore size of about 9.5 nm. Both two types of mesoporous ZSM-5 zeolites exhibited large surface area and mesopore structure. The steam-assisted crystallization(SAC) was performed with lower consumption of solvents. This two-step method may also be suitable for synthesizing other ordered mesoporous zeolites used as catalysts in some catalytic processes.     

Highly ordered Ti-SBA-15: Efficient H2 adsorbent and photocatalyst for eco-toxic dye degradation

Highly ordered 2D-hexagonal mesoporous titanium silicate Ti-SBA-15 materials (space group p6mm) have been synthesized hydrothermally in acidic medium employing amphiphilic tri-block copolymer, Pluronic F127 as structure directing agent. Samples are characterized by powder X-ray diffraction, transmission electron microscopy, scanning electron microscopy, FT IR spectroscopy, UV-visible diffuse reflectance measurements, N₂ adsorption/desorption and TG-DTA analysis. XRD and TEM results suggested the presence of highly ordered mesophase with hexagonal pore arrangements. BET surface area for Ti-SBA-15 (924 m² g⁻¹) is considerably higher than the pure silica SBA-15 (611 m² g⁻¹) prepared following the same synthetic route. UV-visible and FT-IR studies suggested the incorporation of mostly tetrahedral titanium (IV) species, along with some six-coordinated sites in the silicate network. This material shows very good H₂ adsorption capacity at higher pressure and excellent catalytic activity in the photocatalytic degradation of ecologically abundant dye methylene blue.     

Synthesis of single crystal-like hierarchically mesoporous titanosilicate Ti-SBA-1

Hierarchically mesoporous titanosilicate Ti-SBA-1 was synthesized with organic mesomorphous complexes of polyelectrolyte(poly(acrylic acid)(PAA)) and cationic surfactant(hexadecyl pyridinium chloride(CPC)) as template, tetraethylsiloxane as silica source and titanium ethoxide as titanium source.By adjusting the amount of titanium ethoxide in the synthesis, a series of Ti-SBA-1 particles with different Si/Ti ratio(79–180) were prepared. After incorporation of Ti into the silica framework the wellordered cubic Pm3n mesostructure remained, as well as the morphology, particle size. UV–vis DR spectra of the Ti-SBA-1 materials indicated that incorporated titanium species existed in a highly dispersed state and exhibited tetrahedral and octahedral coordination in the silica framework.     

Silica-supported,single-site titanium catalysts for olefin epoxidation. A molecular precursor strategy for control of catalyst structure

A molecular precursor approach involving simple grafting procedures was used to produce site-isolated titanium-supported epoxidation catalysts of high activity and selectivity. The tris(tert-butoxy)siloxy titanium complexes Ti[OSi(O(t)Bu)(3)](4) (TiSi4), ((i)PrO)Ti[OSi(O(t)Bu)(3)](3) (TiSi3), and ((t)BuO)(3)TiOSi(O(t)Bu)(3) (TiSi) react with the hydroxyl groups of amorphous Aerosil, mesoporous MCM-41, and SBA-15 via loss of HO(t)Bu and/or HOSi(O(t)Bu)(3) and introduction of titanium species onto the silica surface. Powder X-ray diffraction, nitrogen adsorption/desorption, infrared, and diffuse reflectance ultraviolet spectroscopies were used to investigate the structures and chemical natures of the surface-bound titanium species. The titanium species exist mainly in isolated, tetrahedral coordination environments. Increasing the number of siloxide ligands in the molecular precursor decreases the amount of titanium that can be introduced this way, but also enhances the catalytic activity and selectivity for the epoxidation of cyclohexene with cumene hydroperoxide as oxidant. In addition, the high surface area mesoporous silicas (MCM-41 and SBA-15) are more effective than amorphous silica as supports for these catalysts. Supporting TiSi3 on the SBA-15 affords highly active cyclohexene epoxidation catalysts (0.25-1.77 wt % Ti loading) that provide turnover frequencies (TOFs) of 500-1500 h(-1) after 1 h (TOFs are reduced by about half after calcination). These results demonstrate that oxygen-rich siloxide complexes of titanium are useful as precursors to supported epoxidation catalysts.     

Formation of titanium nitride nanoparticles within mesoporous silica SBA-15

We report the first synthesis of titanium nitride (TiN) nanoparticles inside the nanoscale channels of mesoporous silica SBA-15. The TiN precursor, Ti(NMe(2))(4) in toluene, was incorporated into the methyl group-modified channels of the SBA-15 powder. The functionalization of pore surfaces with methyl groups generates hydrophobic surfaces that facilitate impregnation with Ti(NMe(2))(4) and minimizes reactions between the TiN precursor and the hydroxyl groups on the surface of SBA-15. Formation of TiN nanoparticles inside the mesoporous channels of SBA-15 was carried out by subsequent ammonolysis at high temperatures (700-750 degrees C). The final products have been characterized by TEM and EELS images, powder XRD patterns, FTIR spectra, UV-vis absorption spectra, and nitrogen adsorption isotherm measurements to confirm the presence and distribution of TiN nanoparticles in the SBA-15 samples.     

Synthesis, characterization and catalytic behavior of functionalized mesoporous SBA-15 with various organo-silanes

Mesoporous silica SBA-15 has been synthesized and functionalized by one-step synthesis method to widen their various application possibilities. In this study, phenyltrimethoxysilane (PTMS), 3-mercaptopropyltrimethoxysilane (MPTMS) and trimethoxypropylsilane (TMPS) were used as silane precursors for the functionalization, and after treated with HCl solution, their catalytic activities were evaluated in the lactic acid-methanol esterification. The presence of anchoring of functional groups on SBA-15 was proved by XRD, FT-IR, BET surface area and pore size distributions. Good catalytic activity was observed especially for SBA-15-SO(3)H-MPTMS, and the catalytic activity order was determined as follows: SBA-15-SO(3)H-MPTMS>SBA-15-TMPS>SBA-15-PTMS, which is directly associated with the surface area, pore size and pore volume. As compared with homogeneous catalyst, SBA-15-SO(3)H-MPTMS heterogeneous catalyst shows remarkable performance, such as separation, recovery and reusability.