抗坏血酸在β-环糊精/聚苯胺修饰玻碳电极上的电化学行为

研究了抗坏血酸在β-环糊精/聚苯胺修饰玻碳电极上的电化学行为。采用电聚合方法制备了β-环糊精/聚苯胺修饰玻碳电极,在聚苯胺和β-环糊精的协同作用下,电极对抗坏血酸具有显著的催化氧化作用。抗坏血酸浓度在1.0×10-6~1.0×10-4 mol·L-1范围内与其氧化峰电流呈线性关系,检出限(3S/N)为8.1×10-7 mol·L-1。对5.0×10-6 mol·L-1的抗坏血酸溶液连续测定6次,测定值的相对标准偏差为0.21%。该方法选择性和重复性好,可在多巴胺存在下选择性测定抗坏血酸。     

抗坏血酸在石墨烯/聚苯胺复合膜修饰电极上的电化学行为

通过原位聚合的方法制备石墨烯/聚苯胺复合物,并将其滴涂于玻碳电极表面,得到石墨烯/聚苯胺复合膜修饰电极。采用循环伏安法研究了抗坏血酸在石墨烯/聚苯胺复合膜修饰电极上的电化学行为。结果表明,在pH=3.0的磷酸盐缓冲溶液中,抗坏血酸在该修饰电极上出现一个明显的氧化峰,氧化峰电流与其浓度在5.0×10-7~1.0×10-3 mol/L范围内呈良好的线性关系,检出限为1.9×10-7 mol/L。该修饰电极可以用于维生素C片中痕量抗坏血酸的测定,加标回收率为97.5%~105%。     

聚L-谷氨酸修饰电极对尿酸的电催化及其应用

用循环伏安法制备了聚L-谷氨酸修饰玻碳电极,研究了尿酸在该电极上的电化学行为。实验结果表明,在pH5.0的磷酸盐缓冲溶液介质中,聚L-谷氨酸修饰玻碳电极对尿酸的氧化具有良好的电催化作用,催化氧化峰电流与尿酸的浓度在2.5×10-6~1.0×10-5mol/L范围内具有良好的线性关系,相关系数r=0.9943。利用该法直接测定人体尿样中尿酸的含量,回收率为98.2%~102.2%。     

尿酸在聚L-苯丙氨酸修饰电极上的伏安测定

采用循环伏安法制备了聚L-苯丙氨酸薄膜修饰玻碳电极,研究了尿酸在该修饰电极上的电化学行为,循环伏安法测定了尿酸. 研究发现,在pH=5.6的磷酸盐缓冲溶液中,尿酸在聚L-苯丙氨酸修饰电极上于0.43 V处产生1灵敏的氧化峰;循环伏安法测定其氧化峰电流与尿酸的浓度在2.0×10-6～3.0×10-4 mol/L呈良好的线性关系,检出限为1×10-6 mol/L. 对1.0×10-5 mol/L尿酸平行测定5次,相对标准偏差为3.0%. 该聚合物修饰电极制作简单,重现性好,可用于尿液中尿酸的测定,结果令人满意.     

尿酸在石墨烯修饰玻碳电极上的电化学行为及测定

以抗坏血酸为还原剂,采用微波水热法化学还原氧化石墨烯合成了石墨烯纳米片,制备了石墨烯修饰的玻碳电极(RGO/GCE),并采用循环伏安法、计时电量法、交流阻抗法等电化学技术研究了尿酸在该修饰电极上的电化学行为及其影响因素。结果表明,在PBS缓冲溶液中,尿酸(UA)在石墨烯修饰电极上的电极反应是一个受扩散控制的不可逆氧化过程。电极反应的转移电子数n=2,有效面积A=0.182 cm2,扩散系数D=1.51×10-6 cm2.s-1。UA的氧化峰电流与其浓度在5.0×10-6～1.5×10-4 mol/L范围内呈良好线性,r=0.995 7。利用该RGO/GCE修饰电极可以快速准确地测定UA,检出限为2.7×10-7 mol/L,加标回收率为98%～100%。     

抗坏血酸在石墨烯微片修饰玻碳电极上的电化学行为及其测定

基于石墨烯微片修饰玻碳电极对抗坏血酸的电催化作用,建立了测定抗坏血酸的电化学分析方法。石墨烯微片修饰玻碳电极与裸玻碳电极相比,显著提高了抗坏血酸的氧化峰电流,降低了氧化峰电位,提高了测定的灵敏度。该电极测定抗坏血酸的线性范围为5.0×10-5～2.5×10-2mol/L,最低检测限为6.5×10-7mol/L(信噪比=3)。     

聚茜素黄R膜修饰电极对尿酸电催化及对人尿中尿酸的检测

用电聚合的方法制备了聚茜素黄R膜修饰的玻碳电极,研究了尿酸在该电极上的电化学行为。结果表明,该修饰电极对尿酸的氧化具有良好的电催化能力。示差脉冲伏安法测定尿酸的氧化峰电流与其浓度在1.0×10-6～1.0×10-4mol/L范围内呈现良好的线性范围,检测限为8.6×10-7 mol/L(S/N=3)。本方法用于人尿液中尿酸含量的测定,结果令人满意。     

基于多壁碳纳米管/壳聚糖多层膜修饰玻碳电极邻苯二酚的测定

改进了碳纳米管在壳聚糖溶液中的分散方法,制备了多壁碳纳米管/壳聚糖多层膜修饰玻碳电极,对比了不同修饰层数膜电极的循环伏安和电化学阻抗行为,5层多壁碳纳米管/壳聚糖膜修饰玻碳电极的电化学性能优良.在最优实验条件下,该修饰玻碳电极对邻苯二酚(CAT)有灵敏的响应,CAT浓度在3.99×10-6～9.09×10-4mol/L范围内与氧化峰电流呈良好的线性关系,检出限为2.39×10-6mol/L(S/N=3).该修饰玻碳电极性能稳定,测定4×10-5mol/LCAT溶液,RSD(n=10)为2.1%;15周后,该电极的响应值仅降低1.9%.     

银掺杂聚L-酪氨酸修饰电极的制备及对尿酸的测定

利用循环伏安法将银和L-酪氨酸聚合修饰在玻碳电极表面,制成银掺杂聚L-酪氨酸(Ag-PLT/GCE)修饰电极,研究了尿酸在该电极上的电化学行为,建立了循环伏安法测定尿酸的新方法。在pH=3.0的磷酸盐缓冲溶液中,扫描速率为100mV/s时,尿酸在该修饰电极上产生一氧化峰,Epa=0.637V(vs.Ag/AgCl)。用循环伏安法进行测定时,峰电流与尿酸浓度在8.0×10-7～1.0×10-5mol/L和1.0×10-5～1.0×10-4mol/L范围内呈良好的线性关系,检出限为3.0×10-7mol/L。方法用于尿样中尿酸的测定,结果满意。     

聚苯胺-石墨烯修饰玻碳电极同时测定邻苯二酚和对苯二酚

本文制备了聚苯胺-石墨烯修饰玻碳电极,并用循环伏安(CV)法和微分脉冲伏安(DPV)法研究了邻苯二酚(CC)和对苯二酚(HQ)在该修饰电极上的电化学行为。实验结果表明,相对于裸玻碳电极,HQ和CC在聚苯胺-石墨烯修饰电极上的氧化峰电流显著提高,氧化峰电位相差104.8mV,实现了CC和HQ的选择性测定。DPV法同时测定二酚时,HQ和CC分别在1.0×10-6~8.0×10-4 mol/L浓度范围内与其峰电流呈良好的线性关系,相关系数R分别为0.998、0.997,检出限(S/N=3)分别为1.0×10-7、8.0×10-8mol/L。将该方法用于模拟水样分析,回收率为95.3%~103.5%。     

槲皮素修饰的双层脂膜的伏安研究

槲皮素修饰的从层脂膜作为研究抗病毒药物的一种模型体系,用循环伏安法测定了槲皮素在脂膜界面上的氧化还原性质和配位性质。在电位扫描过程中,微量铜离子能催化槲皮素的氧化,当双层脂膜的两侧存在着合适的氧化还原偶时,就会产生跨膜的电子传递。     

用毛细管色谱法测定丙烯腈及其合成过程的副产物

用毛细管色谱内标定量法,同时测定丙烯腈及其合成过程的副产物,此法快捷、方便、具有较高的准确度。     

碳络羰基铁簇用于费托合成低碳烃

在费托反应合成烃类的研究方面,有关CO解离和碳化物形成机理已为众多的学者所接受。铁催化剂与合成气作用,易于生成碳化物和氧化物。一般认为碳化物是甲烷和链增长的中间物种。通过金属有机化合物的研究,M_4C、M_3CH,M_2CH_2和M_1CH_3(M=金属)均已被合成、分离和鉴定,并巳知这些碳化物的加氢活化能的顺序为M_4C>M_3CH>M_2CH_2>M_1CH_3。     

MECHANISM OF PHOTOREDUCTION OF THIAZINE DYES BY EDTA STUDIED BY FLASH-PHOTOLYSIS-I

Abstract— The photoreduction of thiazine dyes by ethylene diamine tetraacetic acid (EDTA) was investigated by Rash photolysis. This reaction was found to occur according to a three-step mechanism. the first being the formation of the dye triplet state followed, in weakly acid solutions, by protonation. During the second step, the triplet state of the dye disappears through two competing processes: spontaneous deactivation and reaction with EDTA, which leads to the semireduced dye. The third step leads to the leucodye. It is shown that the overall quantum yield of photoreduction is governed by the second step and can be calculated from the ratio of the rate constants of the two elementary processes involved in this step. This ratio was measured over a wide pH range.     

电导率法和光度法测定乙醇含量

通过测定不同含水量的硝酸钴乙醇溶液的电导率和吸光度，从而建立回归方程，并通过显著性检验，发现溶液的水含量与其电导率成正相关；与其在520nm波长处的吸光度成负相关。根据此特性，可用于乙醇中水含量的快速测定。     

氨基修饰超高交联树脂对单宁酸的吸附行为及机理研究

选用单宁酸作为天然有机酸中典型中分子、高水溶性有机酸,系统研究了氨基修饰超高交联树脂对单宁酸的吸附行为和机理.吸附等温线表明氨基修饰超高交联树脂WJN-08对单宁酸有较高的吸附容量,其静态饱和吸附量比传统商业吸附剂高15%以上;吸附表面分析表明离子键、π-π共轭作用和阳离子-π键是重要吸附作用力;吸附热力学试验表明树脂WJN-08吸附单宁酸是化学吸附主导,吸附焓变在20~22 kJ mol-1;吸附动力学试验表明树脂WJN-08吸附单宁酸速率同时受控于颗粒内扩散和膜扩散过程.动态小柱吸附-脱附实验表明树脂WJN-08对单宁酸有较好的吸附-脱附性能,饱和吸附量和穿透吸附量分别为24.43 mg g-1和19.56 mg g-1,脱附率为98.6%。     

POLYCAPROLACTAM MODIFIED BY POLYBENZIMIDAZOLE

Three polycaprolactam samples modified by 0.05—0.50% polybenzimidazole (PBI) by weight were prepared. Their structure and mechanical properties were characterized by means of FT-IR, SEM, DTA, density tensile, impact and viscoelastic method. PBI delayed the superimposed polymerization-crystallization process of the activated anionic polymerization of caprolactam. The monomer casting (MC) nylons modified by PBI had lower crystallinities, lower T_g and more nearly perfect spherulites than MC nylon itself, and showed a typical toughening effect.     

POLYCAPROLACTAM MODIFIED BY POLYPHENYLQUINOXALINE

Three polycaprolactam samples modified by 0.05—0.50% polyphenylquinoxaline(PPQ)by weight were prepared.Their structure and mechanical properties were characterized by FT-IR, SEM, density, tensile, impact, DTAand visco-elastic method, PPQ induced the formation of "crystal grains" distributed evenly over nylon spherulites in modified samples, which were observed for the first time, and strengthened modified samples. Modified nylons had higher crystallinities, higher T_g, more nearly perfect spherulites than MC nylon itself, and showed typical reinforcing effect on mechanical properties.     

PHOTOSENSITIZATION BY ANTIMALARIAL DRUGS

Abstract The antimalarial drugs, chloroquine, hydroxychloroquine, quinine, quinacrine, amodiaquine and primaquine and the local anaesthetic, dibucaine, were tested for in vitro photosensitizing capability by irradiation with 365 nm UV light in aqueous solutions. The ability of these compounds to photosensitize the oxidation of 2,5-dimethylfuran, histidine, tryptophan or xanthine, and to initiate the free radical polymerization of acrylamide was examined in the pH range 2-12. Chloroquine and hydroxychloroquine show maximal photooxidative behaviour when in the monocation form at pH 9, in contrast to quinine which is extremely efficient as the dication below pH 4. This pattern appears to relate to the fluorescence yield as a function of pH. Chloroquine in the monocation or neutral form was found to undergo dechlorination upon irradiation, and this correlates directly with its ability to initiate photo-polymerization of acrylamide. Quinine also gives rise to small polymerization rates, attributed to photo-ionization in the quinoline ring, yielding a cation radical. Amodiaquine, primaquine and quinacrine do not have significant photochemical activity in aqueous solution. Dibucaine exhibits a strong photosensitizing capability at low pH, similar to quinine.     

SINGLET MOLECULAR OXYGEN QUENCHING BY SATURATED AND UNSATURATED FATTY-ACIDS AND BY CHOLESTEROL

The rate constants of molecular singlet oxygen quenching by saturated and unsaturated fatty-acids and by cholesterol-membrane critical components - membrane critical components - have been measured by time resolved detection of the 1270 nm phosphorescence of singlet molecular oxygen [O2(1deltag)]. We have determined (i) an increment of 5.7 x 10(2)M(-1)s(-1) per -CH2- in C6D6 and CD3OD for saturated fatty acids between C4 and C20, (ii) an increment of 3 x 10(4)M(-1)s(-1) per non-conjugated cis-double bond for C18 unsaturated fatty acids, identical in C6D6 and DC3OD, (iii) a lower quenching rate constant by a factor of 2.7 for the trans-C16 and trans-C18 as compared to the corresponding cis-monounsaturated fatty acids, (iv) a rate constant of O2x(1deltag) quenching by cholesterol of 5.7 x 10(4)M(-1)s(-1) in benzene. These rate constants are compared to those obtained for other membrane cellular components.