成核剂含量对β晶相聚丙烯结晶与熔融行为的影响

用DSC研究了β成核剂含量对β聚丙烯在等温与非等温结晶条件下的结晶与熔融行为的影响,发现当成核剂含量为0.005％时,结晶焓△H_c、β晶的熔融焓△H_(mβ)及熔点T_(mβ)均为最大,而α晶的相对含量最小.广角X-衍射数据表明,成核剂含量高的试样的(301)衍射峰的相对强度下降,反映分子链排列的纵向有序性降低.根据聚丙烯分子在β成核剂上附生结晶的成核机理解释了上述结果.     

β晶相聚丙烯的研究——Ⅲ. 乙丙嵌段共聚物

乙丙嵌段共聚物中的丙烯链段在β晶型成核剂存在下,可在20—140℃结晶成高纯度的β晶型。研究了结晶温度对试样中β晶型的相对含量及试样熔融行为的影响。发现依赖于结晶温度、形成了二类β晶型。在20—100℃淬火形成的β晶型、熔融后会重结晶成稳定的β晶型,在高于100℃结晶则形成稳定的β晶型。研究了β晶型试样的力学性质,发现其屈服强度低于而抗冲强度高于α晶型试样。     

稀土氧化物对聚丙烯晶型和动态力学性能的影响

本文用DSC和粘弹谱仪研究了La_2O_3,Y_2O_3和混合稀土氧化物对全同聚丙烯(iPP)的结晶行为,熔融行为和动态力学性能的影响。结果表明不同的iPP/稀土氧化物复合材料中iPP的晶型不同,Y_2O_3和稀土氧化物是iPP的α和β晶成核剂,La_2O_3是α晶成核剂。含有β晶试样同只有α晶试样相比,在T_g真松弛区其tanδ值较低,贮能模量E从-50℃～+50℃较高,从+50℃～+145℃则E值较低。     

聚丙烯合金PP-c的晶相结构及形态

用偏光显微镜和广角X射线衍射研究了聚丙烯合金PP c的结晶形态.发现PP -c的晶相结构中不仅存在α-晶型聚丙烯(α- PP ) ,也存在着β-晶型聚丙烯(β-PP) .计算了不同乙烯含量PP c的结晶度和β- PP含量.表明随着乙烯含量的增加,β- PP的含量增加,而PP- c的结晶度下降.通过与同等熔融结晶条件下等规聚丙烯(iPP)的结晶形态相比较,发现乙烯组分含量的增加,改变了球晶的生长状况,降低了PP- c晶相的晶体完整性.     

聚丙烯β相结晶的研究

本文研究了冷却速率、结晶温度和熔体温度等因素对聚丙烯β相结晶得到的试样的熔融行为的影响。发现β晶型熔融峰的面积随冷却速率的降低或结晶温度的升高而增加。在低于300℃的温度下,熔体温度对聚丙烯的β相结晶无影响。300℃以上的高温破坏了聚丙烯β相结晶的晶核,冷却结晶时不再生成β相晶体。测定了α相及β相球晶在123—140℃的温度范围内线性增长速率,发现在140℃以下,β球晶的增长速率大于α球晶。研究了β相结晶动力学,发现聚丙烯β相结晶不符合Avrami方程,而要用不完全球晶结晶的动力学理论来描述。     

β型聚丙烯注塑件的分层结构与力学性能

用X-射线衍射仪研究了不加和加成核剂形成不同晶型的三种聚丙烯注塑件的分层结晶结构,获得各层结晶度和β晶型含量(k_β)随皮芯距离的分布规律,测定了试件弯曲、拉伸和冲击性能。发现,纯等规聚丙烯试件主要含α晶型,皮层的结晶度和k_β低于芯层。加有α成核剂的试件仅含有α晶型,皮层的结晶度也低于芯层。加有β成核剂的试件主要含β晶型,皮层的结晶度和k_β值高于芯层。纯聚丙烯试件和β型为主的试件的分层结构中存在α晶和β晶间的转变。与α型聚丙烯相比,β型聚丙烯有较低的屈服强度,却有较高的抗张强度,显示很高的拉伸韧性和延展性,可明显提高室温以及玻璃化温度以下的低温抗冲击性能。     

由N—催化剂催化聚合的聚丙烯结晶行为研究

用小角X-射线散射法(SAXS),广角X-射线衍射法(WXAD)和差示扫描量热法(DSC)对由N-催化剂催化聚合的聚丙烯结晶行为进行探讨。发现这种聚丙烯结晶中有β晶型存在,且其含量随结晶时间增加而增加随结晶温度升高而降低;β晶含量增加,聚合物的长周期也会增加,β晶对长周期的影响比α晶更大。乙烯共聚改性后的聚丙烯因分子链规整性下降而阻止了β晶的形成。在熔融状态下结晶时,β晶的形成要求聚丙烯的分子链具有更高的规整性。这些实验结果均从分子链段结晶机理得到了解释。     

相变过程对等规聚丙烯/炭黑复合材料中填料网络的影响

采用柔和混合方法制备出炭黑(CB)填充等规聚丙烯(iPP)复合材料,CB在iPP熔体中可以进行团聚而形成填料网络,采用动态流变-电阻同步测试的方法,研究原位结晶-熔融过程对所形成网络的影响.实验结果表明,经历原位结晶-熔融后复合材料中可以被动态流变实验检测到的填料网络消失,这是由于结晶和熔融过程中都会影响填料网络结构,而熔融过程中网络的破坏更为显著.相变后网络的重建过程说明,相变过程不能完全破坏熔体中形成的团聚结构,填料网络容易重新形成.     

β晶型聚丙烯的力学性质

研究了主要含β晶型的聚丙烯在不同温度下的应力-应变性质,并与同一商品牌号得到的α晶型聚丙烯作了对比。发现,β晶型试样的屈服强度低于α晶型,而抗冲击强度则比α晶型试样高1—2倍。结合X射线衍射法对β晶型试样在拉伸过程中发生的晶型转变的研究及形变的分子机制解释了二种晶型试样在力学性质上的差异。     

有机季鏻盐插层改性黏土诱发聚丙烯γ晶

选用有机季鏻盐作为插层剂对黏土进行有机化插层改性,制备出有机黏土,通过熔融插层法制备聚丙烯/有机黏土纳米复合材料.XRD表明有机季鏻盐改性的黏土与聚丙烯形成结构为剥离型与插层型并存的纳米复合材料.利用DSC研究了纳米复合材料的熔融过程,结果显示有机黏土对聚丙烯的结晶度影响不明显.XRD和DSC的研究均表明,有机黏土可以诱发聚丙烯产生不常见的γ晶型.当黏土含量为5 wt%时,γ晶型占整个结晶部分的12%左右.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.