Aroma composition of red wines by different extraction methods and Gas Chromatography-SIM/MASS spectrometry analysis

One hundred and one volatile compounds, reported in literature as powerful odorants of wine, were quantified by Gas Chromatography-Selective Ion Monitoring/Mass Spectrometry (GC-SIM/MS) in Primitivo, Aglianico, Merlot and Cabernet Sauvignon red wines. Wine samples were extracted by 3 different extraction methods: 1) separation of the alcoholic fraction from the aqueous phase by salting-out and subsequent extraction by liquid-liquid micro-extraction with 1,1,2-trichlorotrifluoroethane (Freon 113); 2) extraction by liquid-liquid micro-extraction with dichloromethane; 3) solid phase extraction (SPE cartridge: 800 mg of LiChrolut EN resin) with pentane-dichloromethane (20:1) and dichloromethane. The selection of the ion fragments used for quantification was directly performed on a red wine sample. For each compound the area of the corresponding peak was normalized respect to the peak of the internal standard and then interpolated in a calibration curve obtained analysing a model wine solution (water, ethanol, tartaric acid and known amounts of analytes and of internal standard). The methods showed a good linearity: r2>0.990, except for farnesol (isomer a and c), octanal, decanal, furaneol and phenylacetic acid with 0.966 < or = r2 < or = 0.990. The 7 most powerful odorants were: beta-damascenone, acetaldehyde, maltol, ethyl 2-methylbutanoate, ethyl 3-methylbutanoate, 3-methylbutanoic acid and acetal; 7 other slightly less important were: ethyl hexanoate, ethyl acetate, 1-octen-3-ol, butanoic acid, rose oxide, furaneol and sotolon. The Aglianico wines were characterised by the major fermentation compounds (esters, fatty acids and 2-phenylethanol), beta-damascenone, beta-ionone and linalool. The Primitivo wines were characterized by furaneol, methoxypyrazine, gamma-nonalactone and acetaldehyde, while Cabernet Sauvignon and Merlot wines principally by cask derivates (vanillin, (Z) 3-methyl-gamma-octalactone [(Z) wiskylactone], maltol and eugenol), some aldehydes and 3-isopropyl-2-methoxypyrazine.     

Analysis of several phenolic compounds with potential antioxidant properties in grape extracts and wines by high-performance liquid chromatography-photodiode array detection without sample preparation

A RP-HPLC method that allows the separation of several types of phenolic compounds present in grapes and wines by direct injection of samples, using a binary gradient with solvents free of salts and photodiode array detection is described. Results show that more than 15 different phenolic molecules with antioxidant properties (flavan-3-ols, anthocyanins, cinnamic acid derivatives, flavonol derivatives and trans-resveratrol) may be separated in a single run by direct injection of red wine. The method is also valuable for the analysis of these compounds in white wine and in skins, seeds and pulp extracts of red and white grapes.     

Volatile compounds responsible for aroma of Jutrzenka liquer wine

Jutrzenka is a sweet liquer wine produced in Poland from the grape variety of the same name, developed in Poland to withstand the harsh climate of winery regions. Jutrzenka wine has a characteristic aroma with strong fruity and flowery notes, which make it unique among other liquer wines as demonstrated in sensory profile analysis. The work was aimed at characterization of volatile compounds in this wine, with the emphasis on characterization of compounds responsible for its unique aroma. Gas chromatography-olfactometry (GC-O) was applied to identify the key odorants using aroma extract dilution analysis (AEDA) approach. To facilitate free and bound terpenes and C(13)-norisoprenoids identification solid phase extraction (SPE) was used followed by GC/MS. Among identified key odorants β-damascenone was the compound having the highest FD (4096), followed by isoamyl alcohol, 4-mercapto-4-methyl-2-pentanone (FD=2048), methional, linalool, ethyl decanoate (FD=1024) and ethyl hexanoate, furaneol (FD=512). Other significant compounds were ethyl 2-methyl propanoate, ethyl 2-methylbutanoate and phenyl ethyl alcohol. Determination of odor activity values (OAV) showed the highest values for β-damascenone (566), 4-mercapto-4-methyl-2-pentanone (288) ethyl hexanoate (32) and linalool (7). Jutrzenka exhibited also a rich profile of free, and to lesser extent bound terpenes.     

气相色谱-质谱法分析牛蒡酒香气成分

用乙醚提取，以气相色谱-质谱法分析了牛蒡酒香气的成分，从牛蒡酒中共分离鉴定出36种成分，其中主要成分是乙酸乙酯、已酸、异戊醇，它们约占总量的69%。牛蒡酒中异戊醇与异丁醇的比例高达60：1，表明该酒品质优良。     

Separation of positional isomers by the use of coupled shape-selective stationary phase columns

The successful separation of 2- and 3-methyl-substituted positional isomers of butanol, butyl acetate, and butanoic acid and its ethyl ester, is reported. These compounds are of interest in the study of wine flavour, however the separation of the 2- and 3-methyl isomers may present problems, and more so in the presence of the wine matrix components, when single capillary column gas chromatography (GC) is used. The strategy to achieve separation was based on the use of shape-selective cyclodextrin derivative (CDD) capillary columns (commonly referred to as chiral columns). These columns provide simultaneous resolution of the enantiomeric pairs of the 2-methyl isomers, and at the same time the ability to separate the 3-methyl isomer from the 2-methyl is achieved in all but the case of the ( S)-2- and 3-methylbutanol. The advantages of using shape-selective columns to perform this study is demonstrated, with coupling of two CDD columns giving improved separations of these compounds. Although these compounds are relatively volatile, cryogenic modulated comprehensive two-dimensional GC was shown to provide good pulsed peak profiles with chiral separation in the first dimension when a thicker film trapping column segment was employed. The components of interest were well separated from other wine matrix components.     

Headspace-solid phase microextraction-gas chromatography as a tool to define an index that establishes the retention capacity of the wine polymeric fraction towards ethyl esters

A headspace-solid phase microextraction followed by gas chromatographic analysis (HS-SPME-GC) was developed to be applied in the study of the interactions between the wine polymeric fraction and the ethyl esters: ethyl hexanoate, ethyl octanoate, and ethyl decanoate. Wine models (WM) were prepared with 10% (v/v) aqueous ethanol at pH 3.5 with distinct wine polymeric concentrations prepared from white wine of Vitis vinifera L. var. Fern?o-Pires: 1.0 g L(-1) (PWM1), with a polymeric concentration approaching the real one in wine; 10.0 g L(-1) (PWM10); and 30.0 g L(-1) (PWM30), saturated with polymeric fraction. A reference wine model (RWM) was prepared without polymeric fraction. Each volatile compound (4.0 mg L(-1)) was added separately to the RWM and to the WM with the three levels of polymeric material (PWM). From the retention index (RI) calculated for each compound using the formula: [RI = 1 - (C(RWM) - C(PWM))/C(RWM)], where C(RWM) is the concentration of the compound in the RWM and C(PWM) is the concentration of the compound in the given PWM, the retention capacity of each wine polymeric fraction towards the three esters was established. The higher retention indexes were observed for ethyl decanoate, the more hydrophobic compound, and for the PWM with higher concentration. Furthermore, this study also suggested that the retained compounds are dosed to the headspace, which may promote the perception of their aroma for a longer period of time.     

Stable isotope dilution analysis of wine fermentation products by HS-SPME-GC-MS

The aim of this study was to quantify, in a single analysis, 31 volatile fermentation-derived products that contribute to the aroma of red and white wine. We developed a multi-component method based on headspace solid-phase microextraction coupled with gas chromatography mass spectrometry (HS-SPME-GC-MS). The 31 volatile compounds analysed include ethyl esters, acetates, acids and alcohols. Although these compounds have a range of functional groups, chemical properties, volatilities, affinities for the SPME fibre, and are found in wine at various concentrations, the accuracy of the analysis was achieved with the use of polydeuterated internal standards for stable isotope dilution analyses (SIDA). Nine of the labelled standards were commercially available, while 22 were synthesised. The method was validated by a series of duplicate spiked standard additions to model, white and red wine matrices over the concentration range relevant for each compound in wine. This demonstrated that the appropriate use of SIDA helped to account for matrix effects, for instance potential sources of variation such as the relative response to the MS detector, ionic strength, ethanol content and pH of different wine matrices. The resultant calibration functions had correlation coefficients (R²) ranging from 0.995 to 1.000. Each compound could be quantified at levels below its aroma threshold in wine. Relative standard deviations were all <5%. The method was optimised for the best compromise (over the 31 compounds) of wine dilution factor, level of sodium chloride addition, SPME fibre, SPME temperature, SPME time, GC column and MS conditions. Confirmation of identity was achieved by retention time and peak shape, and measurement of at least three ions for each analyte and internal standard with the MS operating in selected ion monitoring mode to facilitate more precise quantitation with a high sampling rate. The method is a valuable research tool with many relevant applications. A novel method for the combined chiral separation and SIDA quantification of 2- and 3-methylbutanoic acid is also demonstrated.     

Identification of potent odourants in wine and brewed coffee using gas chromatography-olfactometry and comprehensive two-dimensional gas chromatography

Volatile constituents in wine and brewed coffee were analyzed using a combined system incorporating both GC-olfactometry (GC-O) and comprehensive two-dimensional GC-flame ionization detection (GC×GC-FID). A column set consisting of a 15m first dimension ((1)D; DB-FFAP (free fatty acid phase)), and a 1.0m (2)D column (DB-5 phase) was applied to achieve the GC×GC separation of the volatile extracts isolated by using solid phase extraction (SPE). While 1D GC resulted in many overlapping peaks, GC×GC allowed resolution of co-eluting compounds which coincided with the odour region located using GC-O. Character-impact odourants were tentatively identified through data correlation of GC×GC contour plots across results obtained using either time-of-flight mass spectrometry (TOFMS), or with flame photometric detection (FPD) for sulfur speciation. The odourants 2-methyl-2-butenal, 2-(methoxymethyl)-furan, dimethyl trisulfide, 2-ethyl-5-methyl-pyrazine, 2-octenal, 2-furancarboxaldehyde, 3-mercapto-3-methyl-1-butanol, 2-methoxy-3-(2-methylpropyl)-pyrazine, 2-furanmethanol and isovaleric acid were suspected to be particularly responsible for coffee aroma using this approach. The presented methodology was applied to identify the potent odourants in two different Australian wine varietals. 1-Octen-3-ol, butanoic acid and 2-methylbutanoic acid were detected in both Merlot and a Sauvignon Blanc+Semillon (SV) blend with high aroma potency. Several co-eluting peaks of ethyl 4-oxo-pentanoate, 3,7-dimethyl-1,5,7-octatrien-3-ol, (Z)-2-octen-1-ol, 5-hydroxy-2-methyl-1,3-dioxane were likely contributors to the Merlot wine aroma; while (Z)-3-hexen-1-ol, β-phenylethyl acetate, hexanoic acid and co-eluting peaks of 3-ethoxy-1-propanol and hexyl formate may contribute to SV wine aroma character. The volatile sulfur compound 2-mercapto-ethyl acetate was believed to contribute a fruity, brothy, meaty, sulfur odour to Australian Merlot and SV wines.     

Simultaneous determination of endocrine disrupting phenolic compounds and steroids in water by solid-phase extraction-gas chromatography-mass spectrometry

A solid-phase extraction (SPE)-gas chromatography (GC)-mass spectrometry (MS) analytical method for the simultaneous separation and determination of endocrine disrupting chemicals (EDCs) from water samples is described in detail. Important and contrasting EDCs including estrone, 17beta-estradiol, 17beta-ethynylestradiol, 16beta-hydroxyestrone, 4-nonylphenol, bisphenol A and 4-tert-octylphenol were selected as the target compounds. The SPE technique, followed by the derivatisation with bis (trimethylsilyl) trifluoroacetamide was used for the extraction recoveries of target compounds from water samples. A number of parameters that may affect the recovery of EDCs, such as the type of SPE cartridges, eluents, as well as water properties including pH value, and concentration of salts and humic substances were investigated. It is shown that the Oasis cartridges produced the best recoveries of target EDCs while ethyl acetate was efficient in eluting EDCs from SPE cartridges. The recovery of some EDCs was enhanced by the addition of salt, but reduced by the increase in pH value and humic acid concentration. The optimised method was further verified by performing spiking experiments in natural river water and seawater matrices, with good recovery and reproducibility for all the selected compounds. The established method was successfully applied to environmental water samples from East and West Sussex, UK, for the determination of the target EDCs.     

Influence of Fermentation Method on Phenolics,Antioxidant Capacity,and Volatiles in Blackberry Wines

The influence of the type of fermentation method on phenolics, antioxidant capacity, and volatiles in blackberry wine was studied. Dry blackberry wines made by traditional fermentation (TF) and carbonic maceration fermentation (CMF) were analyzed for total polyphenols, flavanols, flavonoids, anthocyanins, proanthocyanidin, and antioxidant capacity. High-performance liquid chromatography was used for analysis of nonflavonoid phenolics (gallic, benzoic, salicylic, syringic, caffeic, coumaric, and ferulic) and flavonoids (catechin, quercetin, and rutin). Volatiles were detected by gas chromatography-mass spectrometry. The results showed that CMF fermentation afforded higher antioxidant activity and phenolic content, especially individual polyphenolics. The total level of phenolics in the CMF wine was substantially higher than in traditional wines: 2953 mg of gallic acid equivalents (GAE)/L for CMF wine vs. 1647 mg of GAE/L for traditional wine. A total of 53 kinds of volatile compounds were detected. Of these, 35 were detected in traditionally brewed wine and 46 in CMF fermented wine. Thus, CMF wine had a more complement volatile profile. The dominance of fruity and floral odor components derived from ethyl esters of fatty acids resulted in the indistinguishable aroma of TF and CMF wines. But, CMF wine had a more complicated aroma. The present results could complement existing theory on the processing of blackberry wines.     

HPLC study of the efficiency of extraction of phenolic compounds

Summary The rate of extraction of phenolic compounds in two different solvents has been studied by liquid chromatography (HPLC) under reverse phase, gradient elution conditions. The solvents were diethyl ether and ethyl acetate. The method has been applied to two natural samples, a white wine and apple pulp.     

蛇龙珠干红葡萄酒香气成分的GC-MS分析

研究宁夏贺兰山东麓地区蛇龙珠(Cabemet Gemischt)干红葡萄酒香气的化学成分,采用溶液萃取法提取蛇龙珠干红葡萄酒中的香气成分;用气相色谱一质谱进行分离测定,结合计算机检索技术对分离化合物进行鉴定,应用TIC峰面积归一法测定各成分的相对含量;分离出32个峰,鉴定出29个香气化学成分,共占其色谱流出组分总量的98．06％;其中相对含量以3-甲基丁醇(47．97％)、丁二酸二乙酯(16．49％)、苯乙醇(10．33％)、2-羟基丙酸乙酯(6．41％)、2-甲基丙醇(3．51％)、二氢化-2[3氢]-呋喃酮(2．07％)、2,3-丁二醇(1．93％)、四氢化2-甲基噻吩(1．68％)、乙酸乙酯(1．21％)、己醇(0．95％)等成分为主。     

Isocratic chromatography of resveratrol and piceid after previous generation of fluorescent photoproducts: wine analysis without sample preparation

Resveratrol and its 3-glucoside (piceid), are stilbene-like molecules produced by plants. Both of them are weakly fluorescent, but highly fluorescent compounds are obtained when their hydroethanolic solutions are UV-irradiated, which implies a substantial improvement in the sensitivity of analytical methods. Experimental design (central composite design) together with the response surface methodology have been used to find optimum conditions for the fast, sensitive, and precise chromatographic analysis (with isocratic elution) of resveratrol and piceid in wine samples. These compounds have been UV-transformed into their respective photoproducts, which have been separated in a C18 column (Novapack C(18) 150x3.9 mm, 4 microm) by isocratic elution, using a mobile phase made up of acetonitrile and 4.1 vol% aqueous acetic acid, 19:81 v/v, at a flow rate of 0.8 mL/min, and fluorimetrically detected at 364 nm (lambda(exc) = 260 nm). Detection limits (S/N = 3) are 0.29 and 0.28 microg/L for resveratrol and piceid, respectively. The method has been applied to the analysis of these compounds in wine samples without a clean-up step. The analysis is completed in only 20 min. The standard addition method has been applied to the analysis of a commercial red wine and average recoveries near 100% were obtained for resveratrol and piceid. Three wine pools were satisfactorily analysed by external calibration.     

Fast analysis of important wine volatile compounds development and validation of a new method based on gas chromatographic-flame ionisation detection analysis of dichloromethane microextracts

A method for the simultaneous determination of major (10-200 mg/l) and minor (0.1-10 mg/l) volatile compounds from wine has been optimised and validated. A 3-ml volume of wine is diluted with water (7 ml), salted with 4.5 g of ammonium sulfate and extracted with 0.2 ml of dichloromethane. The extract is injected in the split mode in a GC system, separated on a Carbowax 20M capillary column and detected by flame ionisation detection. Volatiles from wine are divided into four groups according to their behaviour in the extraction, and a specific internal standard has been selected for each group. The method allows satisfactory determination of more than 30 volatile compounds of wine. Compounds analysed include acetaldehyde, diacetyl, acetoine (3-hydroxy butanone), fusel alcohols and their acetates, and fatty acids and their ethyl esters. The linear dynamic range of the method covers the normal range of occurrence of analytes in wine and extends from at least one magnitude order to more than two, with typical r2 between 0.9938 and 0.9998. Reproducibility ranges from 3.1 to 10% (as RSD) with 5.5% as the average. The analysis of spiked samples has shown that matrix effects do not significantly affect method performance.     

葡萄酒中白藜芦醇的固相萃取GC/MS法测定及其生理活性的初步研究

用反向C₁₈固相萃取小柱对葡萄酒进行了预处理,然后用BSTFA硅烷化试剂对萃取物进行了衍生化处理,用气相色谱/质谱对葡萄酒中顺式、反式白藜芦醇进行了同时测定,建立了定量分析方法.对方法的精密度和回收率进行了测定,方法的相对标准偏差分别为4.48%(顺式)和5.23%(反式).顺式、反式白藜芦醇的平均回收率分别为94.4%和97.6%.并对10种国产葡萄酒和两种进口葡萄酒样品进行了测定.对白藜芦醇的生理活性也进行了实验,初步探讨了白藜芦醇对大鼠血管平滑肌细胞(VSMC)、大肠癌细胞株Lovo细胞和小鼠成纤维株3T3细胞的生长生殖活性的影响,观察了其形态变化.     

超高效液相色谱-电喷雾串联质谱法直接测定黄酒和葡萄酒中氨基甲酸乙酯

建立了超高效液相色谱-电喷雾串联质谱(UPLC-ESI-MS/MS)直接测定黄酒和葡萄酒中氨基甲酸乙酯含量的方法。黄酒和葡萄酒样品经蒸馏水简单稀释后,过0.22 μm微孔滤膜,直接进行UPLC-MS/MS分析检测。以Waters Acquity UPLCTMBEH C18色谱柱为分析柱,乙腈和0.1%(v/v)乙酸水溶液为流动相,采用电喷雾正离子(ESI+)模式电离,多反应监测(MRM)模式检测,以氨基甲酸丁酯(BC)作为内标进行定量。结果表明: 方法在2～500 μg/L的范围内线性关系良好(相关系数大于0.995),其对黄酒和葡萄酒的检出限为1.7 μg/L,定量限为5.0 μg/L,可达到黄酒和葡萄酒中氨基甲酸乙酯的检测要求。当添加水平为10、20和100 μg/L时,黄酒和葡萄酒中待测组分的回收率为90%～102%,日内精密度(n=6)为0.8%～4.5%,日间精密度(n=6)为1.4%～5.6%。该方法样品处理简单,前处理过程不使用有机溶剂,测定快速、准确,灵敏度高,非常适合黄酒和葡萄酒中氨基甲酸乙酯的快速检测和定量分析。     

Classification of wines from five Spanish origin denominations by aromatic compound analysis

Wine is a complex matrix in which aroma compounds play an important role in the characterization of the flavor pattern of a given wine. Twelve volatile compounds were determined in 244 samples of Spanish red wines from different denominations of origin: Rioja, Navarra, Valdepe?as, La Mancha, and Cari?ena. The samples were analyzed by GC using headspace solid-phase microextraction. The concentration (mg/mL) intervals obtained were 3-methyl-butyl acetate (3.9 to 116), 3-methyl-1-butanol (93 to 724), ethyl hexanoate (0.8 to 39), 1-hexanol (0.3 to 6.7), ethyl octanoate (1.4 to 41), diethyl succinate (0.2 to 13), 2-phenyl ethyl acetate (0 to 5.3), hexanoic acid (0 to 8.3), geraniol (0 to 3.0), 2-phenylethanol (1.5 to 56), octanoic acid (0 to 20), and decanoic acid (0 to 3.3). Wines were classified by multivariate statistical methods: principal component analysis, and lineal discriminant analysis. A correct differentiation among wines according to their origin was obtained by lineal discriminant analysis.     

On-line monitoring of continuous beer fermentation process using automatic membrane inlet mass spectrometric system

A fully automatic membrane inlet mass spectrometric (MIMS) on-line instrumentation for the analysis of aroma compounds in continuous beer fermentation processes was constructed and tested. The instrumentation includes automatic filtration of the sample stream, flushing of all tubing between samples and pH control. The calibration standards can be measured periodically. The instrumentation has also an extra sample line that can be used for off-line sample collection or it can be connected to another on-line method. Detection limits for ethanol, acetic acid and eight organic beer aroma compounds were from μg l⁻¹ to low mg l⁻¹ levels and the standard deviations were less than 3.4%. The method has a good repeatability and linearity in the measurement range. Response times are shorter than or equal to 3 min for all compounds except for ethyl caproate, which has a response time of 8 min. In beer aroma compound analysis a good agreement between MIMS and static headspace gas chromatographic (HSGC) measurements was found. The effects of different matrix compounds commonly present in the fermentation media on the MIMS response to acetaldehyde, ethyl acetate and ethanol were studied. Addition of yeast did not have any effect on the MIMS response of ethanol or ethyl acetate. Sugars, glucose and xylose, increased the MIMS response of all studied analytes only slightly, whereas salts, ammonium chloride, ammonium nitrate and sodium chloride, increased the MIMS response of all three studied compounds prominently. The system was used for on-line monitoring of continuous beer fermentation with immobilised yeast. The results show that with MIMS it is possible to monitor the changes in the continuous process as well as delays in the two-phase process.     

Volatile composition of Baga red wine: Assessment of the identification of the would-be impact odourants

Wines produced from Baga native variety from the Portuguese Bairrada Appellation, harvest 2000, were submitted to a liquid–liquid continuous extraction with dichloromethane and analysis by gas chromatography–mass spectrometry (GC–MS). A total of 53 compounds were identified and quantified. This wine has 225 mg l⁻¹ volatile compounds, which include aliphatic and aromatic alcohols (44%), acids (27%), esters (15%), lactones (6%), amides (5%), and phenols (1%). To achieve the identification of the major would-be impact odourants, the aroma index was calculated using the concentration of each volatile component and the corresponding odour threshold reported in the literature. This methodology proved suitable, as a preliminary step, for the determination of the would-be impact odourants of Baga wine. From the 53 compounds identified, nine were determined as the most powerful odourants: guaiacol, 3-methylbutanoic acid, 4-ethoxycarbonyl-γ-butyrolactone, isobutyric acid, 2-phenylethanol, γ-nonalactone, octanoic acid, ethyl octanoate and 4-(1-hydroxyethyl)-γ-butyrolactone. These data suggest Baga wine as a fruity-type product with an aroma correlated to a restricted number of compounds.