pH敏感的聚(L-谷氨酸)-交联聚丙烯酸水凝胶的合成与性能研究

通过在聚L-谷氨酸侧链部分接枝甲基丙烯酸2-羟乙酯得到含有双键的聚(L-谷氨酸),将其与丙烯酸共聚得到由聚(L-谷氨酸)侧链接枝并交联聚丙烯酸的pH敏感水凝胶.研究水凝胶在不同pH的缓冲溶液中的溶胀性、溶胀动力学,并通过SEM观察水凝胶的微观结构.结果表明,水凝胶在低pH环境下的溶胀率明显低于高pH环境中的溶胀率,不同...     

水凝胶及其在药物控释体系上的应用

智能水凝胶作为药物载体有着良好的应用前景。人体环境中存在一些变化的因素，如温度、pH。因此，温度敏感性水凝胶和pH敏感性水凝胶可用于药物在人体中的控释体系。本文主要介绍水凝胶材料的种类以及智能水凝胶在药物控释体系上的应用。     

pH敏感性智能水凝胶的设计及其应用

水凝胶是一种交联的三维网状亲水性聚合物材料,具有与生物组织相似的特点并且能够吸收大量的水分。作为智能水凝胶的一种,pH敏感性水凝胶因其结构中含有大量碱性或酸性基团从而具有一定的pH敏感性。凭借这些特性,近年来pH敏感性水凝胶在生物、医学、物理、环境、纺织等众多研究领域备受关注。本文围绕p H敏感性水凝胶的响应机制、分类以及应用三个方面进行综述。在响应机制上,本文从响应过程、影响因素和溶胀扩散模型三方面进行综述;在分类上,根据水凝胶敏感性的不同分为溶胀-收缩类和溶胶-凝胶类两类,并进一步根据pH作用范围的不同将溶胀-收缩类细分为阴离子类、阳离子类以及两性离子类,溶胀-收缩类细分为硼酸酯类、酰腙类以及亚胺类;在应用研究上,本文总结了其在医学、环境、生物、智能检测、功能材料等热门领域的研究情况。最后,对pH敏感性水凝胶的未来的发展方向进行了展望。     

刺激响应性水凝胶在肿瘤治疗中的研究进展

恶性肿瘤的治疗在临床中一直备受关注，由于肿瘤细胞的浸润性和顽固性，常规治疗通常会产生严重的毒副作用。相较于全身化疗，局部载药水凝胶的使用显著降低了全身毒性并可实现药物在肿瘤部位的持续递送。此外，经物理掺杂或化学修饰的刺激响应性水凝胶，还可响应环境条件变化(如温度、pH、光等),实现原位交联和药物可控释放，大大提高了临床顺应性和药物递送效率。本综述分类讨论了用于肿瘤治疗的刺激响应性水凝胶的设计策略；汇总了近年来此类水凝胶的研究进展及其药物递送方案；并针对该领域存在的实际问题提出了可能的发展方向。     

明胶-聚异丙基丙烯酰胺水凝胶的pH、温度敏感性

用明胶(Gel)和N 异丙基丙烯酰胺(NIPAM)为原料,制备了Gel/聚异丙基丙烯酰胺(PNIPAM)水凝胶;研究了不同含量的水凝胶的温度、pH敏感性。结果表明:温度对水凝胶pH敏感性的影响取决于水凝胶的组成。明胶含量高的水凝胶,其pH敏感性几乎不受温度的影响;当0.500.90时,pH值几乎不影响水凝胶的温敏性。     

明胶-聚异丙基丙烯酰胺水凝胶的溶胀动力学

采用明胶（Gel)和N－异丙基丙烯酰胺（NIPAM）为原料，制备了Gel/聚异丙基丙烯酰胺（PNIPAM）水凝胶系列；研究了原料配比、pH值及温度对水凝胶溶胀速度的影响。结果表明，当温度大于PNIPAM的最低临界溶液温度（LCST）值时，Gel/PNIPAM水凝胶的溶胀速度随着组分中PNIPAM的增加而降低，且溶胀过程以扩散渗透控制为主。而pH对水凝胶溶胀速度的影响与温度有关。Gel/PNIPAM配比为5／5，温度大于LCST时，水凝胶的pH敏感性受明胶控制；温度低于LCST时，pH对水凝胶的溶胀速度的影响很小。     

海藻酸钠/聚(N-异丙基丙烯酰胺)半互穿网络水凝胶的制备及性能研究

由海藻酸钠(SA)和聚(N-异丙基丙烯酰胺)(PNIPAAm)制得的半互穿网络水凝胶具有温度及pH敏感特性。在酸性(pH=1.3)和弱碱性条件(pH=7．4)下，研究了温度对该凝胶溶胀度的影响，结果表明，该凝胶溶胀度均随着温度的提高而下降，但在pH=1．3时，溶胀度小于PNIPAAm水凝胶的；在pH=7．4时，结果正好相反。在25℃和37℃的条件下，分别考察pH对该凝胶溶胀度的影响，结果表明，在25℃时该凝胶有良好的pH敏感性，而在37℃时，敏感性不明显。同时也发现该凝胶对pH、温度的脉冲刺激有较快的响应性。     

响应性水凝胶及其在生物医药领域应用研究进展

响应性水凝胶又称"智能水凝胶",是以水凝胶为基础,经修饰响应多种理化性质及微小环境变化,从而改变自身性质的一类水凝胶。响应性水凝胶目前广泛应用于生物医药领域、材料领域等,如:制备pH响应性水凝胶负载阿霉素(DOX)治疗癌症,温度响应性水凝胶制作3D生物打印材料用于创伤修复,葡萄糖响应性水凝胶治疗糖尿病足等。本文介绍了响应性水凝胶研究的国内外发展动态,包括响应性水凝胶的制备、修饰方法及其在生物医药领域的应用,并对未来的发展方向进行了讨论与展望。     

羧甲基纤维素基复合水凝胶的研究及应用进展

羧甲基纤维素(CMC)水凝胶是一种具有亲水性的天然三维聚合物材料,具有高吸水性,因此以羧甲基纤维素钠制备的水凝胶安全无毒可生物降解,被广泛应用于医药、食品、农业和环境等领域,作为保鲜材料、抗菌材料、生物传感器、药物输送系统和去除重金属的吸附剂。本文按CMC复合水凝胶材料来源的不同,分类综述了大分子/CMC水凝胶、单体/CMC水凝胶和无机物/CMC水凝胶的研究进展、功能特性以及应用领域,为羧甲基纤维素复合水凝胶的研究提供一定的思路和理论依据。总结此方向研究中不同材料对羧甲基纤维素复合水凝胶性能的提升情况,同时对羧甲基纤维素水凝胶的应用前景进行了展望。     

含儿茶酚基团的湿态组织粘附水凝胶

湿态粘附作用对于生命的孕育和发展具有重要意义。水凝胶是一类兼具固液特性的智能材料，组织粘附水凝胶因多功能性和生物相容性而被广泛应用于伤口闭合和修复、细胞工程、组织工程等领域。然而，湿态组织表面的水合层阻碍了组织粘附水凝胶与组织表面形成界面粘附键。面对这一挑战，受海洋贻贝足丝蛋白中DOPA的儿茶酚基团是水下粘附的关键结构的启发，含儿茶酚基团的湿态组织粘附水凝胶的研究引起了广泛关注。本综述介绍了贻贝足丝蛋白(Mfps)的结构及湿态粘附机理，并将儿茶酚衍生物分为天然Mfps或利用基因工程合成的Mfps、含儿茶酚基团的小分子化合物、儿茶酚基团改性的天然高分子以及含儿茶酚基团的合成功能高分子；随后，概述近十年含儿茶酚基团的湿态组织粘附水凝胶在组织创口修复材料、生物涂层材料、靶向型药物输送材料、生物电子设备材料的研究进展；文末，展望了此类水凝胶材料未来发展面临的机遇和挑战。     

海藻酸钠和聚N-异丙基丙烯酰胺半互穿网络水凝胶的溶胀动力学研究

以海藻酸钠 (SA)和N 异丙基丙烯酰胺 (NIPAM)为原料 ,制备出具有温度敏感性的半互穿网络水凝胶 (SA PNIPAMsemi IPN) .主要研究了海藻酸钠用量、水介质温度及pH值对该凝胶溶胀速率的影响 .结果表明 ,在PNIPAM最低临界溶解温度 (LCST)以下 ,该凝胶的溶胀速率随着凝胶网络中SA组分的增加而增大 ,且溶胀速率取决于高分子链的松弛速率 ;pH对凝胶溶胀速率的影响与温度有关 ,温度对溶胀速率的影响与pH有关 .     

Synthesis and characterization of PVP/AAc copolymer hydrogel and its applications in the removal of heavy metals from aqueous solution

Chelating poly(vinylpyrrolidone/acrylic acid) (PVP/AAc) copolymer hydrogels were prepared by radiation-induced copolymerization. The effects of preparation parameters such as PVP content in the hydrogel and irradiation dose on the swelling behavior of the hydrogel were studied. The pH dependent swelling was investigated. The thermal stability of the prepared hydrogel and the metal chelated ones was characterized by TGA. The removal of Fe(III), Cu(II), and Mn(II) from aqueous solution by the prepared PVP/AAc chelating hydrogel was examined by batch equilibration technique. The influence of treatment time, pH, and the initial feed concentration on the amount of the metal ions removed was studied. The results show that the removal of the metal ion followed the following order: Fe(III) > Cu(II) > Mn(II). The amounts of the removed metal ions increased with treatment time and pH of the medium. To re-use the hydrogel, the metal ions were stripped by using 2 N HCl.     

Synthesis of Carboxymethyl Cellulose Based Drug Carrier Hydrogel Using Ionizing Radiation for Possible Use as Site Specific Delivery System

A unique natural polymer based colon specific drug carrier was prepared from carboxymethyl cellulose (CMC) and acrylic acid (AAc) in aqueous solution employing γ‐radiation induced copolymerization and crosslinking. The effect of preparation conditions such as the natural polymer content and irradiation dose on gelation process was investigated. The swelling behavior of the prepared hydrogels was characterized by investigating the time and pH dependent swelling of the (CMC/AAc) hydrogels of different CMC content. The effects of the hydrogel composition and pH of the swelling medium on the swelling indices were estimated. The results show that the increment in the CMC content in the feed solution enhances the gelation process. The results also show the dependence of the swelling indices on both hydrogel composition and pH value of the swelling medium. To evaluate the ability of the prepared hydrogel to be used as a colon‐specific drug carrier, the release profile of theophylline was studied as a function of time at pH 1 and pH 7.     

γ-irradiated chitosan-polyvinyl pyrrolidone hydrogels as pH-sensitive protein delivery system

The effects of pH of the buffer solution and the composition of the hydrogel system on the bovine serum albumin (BSA) adsorption capacity of chitosan (CS)–polyvinyl pyrrolidone (PVP) (CSPVP) hydrogels and release of BSA were investigated. Poly-electrolyte CSPVP hydrogels with different compositions were prepared by irradiating CS/PVP/water mixtures with γ-rays at ambient temperature. The adsorption capacity of hydrogels was found to increase from 0 to 350 mg BSA/g dry gel, by changing external stimuli and hydrogel composition. The adsorption of BSA within CSPVP hydrogels increased with increase in CS content in the hydrogels. When the irradiation doses of hydrogel increased, the adsorption of BSA decreased. The maximum adsorption of BSA was observed at pH 5. A significant amount of the adsorbed BSA (up to 95%) was eluted in the phosphate medium containing 0.1 M NaCl at pH 7.4.     

Adsorption of Dyes Using Multi-walled Carbon Nanotube Hydrogel

The hydrophilic multi-walled carbon nanotube(MWCNT)hydrogel was prepared using acrylic acid,acrylamide and hydrophilic MWCNT.The orthogonal experiment was applied to optimize the synthetic conditions.The MWCNT hydrogel was characterized by Fourier transform infrared spectrophotometer(FTIR)and scanning electron microscopy(SEM)analysis.The MWCNT hydrogel was used as the adsorbent to adsorb water-soluble cationic dye.This study evaluated the adsorption performance of hydrogels on four dyes of safranine Ts crystal violet,malachite green and methylene blue in water.The effects of the amount of hydrogel,the size of hydrogel,pH;and the temperature on the adsorption performance were investigated.The adsorption kinetic and adsorption isotherm curves were measured.The experimental results show that the MWCNT hydrogel can be easily separated from water and the adsorption capacity is much greater compared to the hydrogel without MWCNT.The MWCNT hydrogels can be used in wastewater treatment with a great potential.     

ABSORPTION OF METAL IONS AND SWELLING PROPERTIES OF POLY(ACRYLIC ACID-CO-ITACONIC ACID) HYDROGELS

Hydrogels of acrylic acid and itaconic acid has been synthesized with different monomers ratios. The swelling process of the different xerogels immersed in water and salt solutions has been studied. The swelling of hydrogels loaded with metal cations (Cu²⁺, Zn²⁺) was also investigated. The swelling process was monitored by the increase in the weight of hydrogel as a function of time. The absorption properties of metal ions were studied by using the hydrogel, and different concentrations of copper and zinc solutions (prepared from sulphate salts). The influence of pH on the absorption process was studied. For the absorption of metal ions, the amount of ions absorbed within the hydrogel can be calculated from the initial and equilibrium concentrations of the metal ions in aqueous phase, the weight of the hydrogel, and the volume of solution used. Metal absorption increased when pH, salt concentration in external solution and itaconic acid content is levelled.

The swelling isotherms which consisted of an initial fast increase levelled off asymptotically to the equilibrium swelling limit. The experimental data clearly suggest that our hydrogels follow a second-order kinetics for both cases (unload and metal loaded). The kinetics rate constant and the equilibrium water content, K, have been calculated for every monomer ratio from the experimental data according to the kinetics equation. Both magnitudes decreased as the itaconic acid content decreases in the xerogels.     

Adsorption and controlled release of Chlortetracycline HCl by using multifunctional polymeric hydrogels

Adsorption and controlled release of Chlortetracycline HCl to and from multifunctional polymeric materials (HEMA/MAA) hydrogels were investigated. P(HEMA/MAA) hydrogels were synthesized by gamma radiation-induced copolymerization of 2-hydroxyethylmethacrylate (HEMA) and methacrylic acid (MAA) in aqueous solution. The influence of copolymer composition and pH value of the surrounding medium on the type of water diffusion into the glassy polymer were discussed. Drug, Chlortetracycline HCl containing hydrogels, with different drug concentration to polymer ratios, was loaded by direct adsorption method. The influence of MAA content in the gel on the adsorption capacities of hydrogel was studied. Chlortetracycline HCl adsorption capacity of hydrogels was found to increase from 8 to 138 mg Chlortetracycline HCl per gram dry gel with increasing amount of MAA in the gel system and drug concentration. The effect of pH on the releasing behavior of Chlortetracycline HCl from gel matrix was investigated. In vitro drug release studies in different buffer solutions show that the basic parameters affecting the drug release behavior of hydrogel are the pH of the solution and MAA content of hydrogel.     

pH and reduction dual‐stimuli‐responsive PEGDA/PAMAM injectable network hydrogels via aza‐michael addition for anticancer drug delivery

A pH and reduction dual‐stimuli‐responsive PEGDA/PAMAM injectable network hydrogel containing “acetals” as pH‐sensitive groups and “disulfides” as reducible linkages was designed and synthesized via aza‐Michael addition reaction between PAMAM and PEGDA diacrylates. The pore size and swelling ratio of hydrogels was varied from 14 ± 3 to 19 ± 4 μm and 214 ± 13 to 300 ± 19 μm, respectively, with varying ethylene glycol repeating units in diacrylates. The swelling ratio of PEGDA/PAMAM network hydrogel increased with increase in the molecular weight of PEG and with decrease in pH. The presence of different cationizable amino‐functionalities in PEGDA/PAMAM network hydrogel helped to enhance the swelling ability of hydrogel under the acidic conditions. The continuous increase in metabolically active live HeLa cells with time in MTT assay implied biocompatibility/noncytotoxicity of the synthesized PEGDA/PAMAM injectable network hydrogel. Furthermore, the prepared PEGDA/PAMAM hydrogel showed higher degradation at lower pH and at higher concentration of DTT. The burst release of doxorubicin from PEGDA/PAMAM hydrogel under the environment of the lower pH and in presence of DTT compared to the release at normal physiological pH and in absence of DTT suggested the potential ability of this model hydrogel system for targeted and selective anticancer drug release at tumor tissues. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2080–2095     

去质子化调控的肝素/壳聚糖抗凝血多层膜

本文研究了环境pH值变化对多层膜表面性能的影响, 并且评价了组装pH值与测试pH值的差异对多层膜血液相容性的影响.     

Controlling degradation of acid-hydrolyzable pluronic hydrogels by physical entrapment of poly(lactic acid-co-glycolic acid) microspheres

Chemically crosslinked biodegradable hydrogels based on di-acrylated Pluronic F-127 tri-block copolymer were prepared by a photopolymerization method. Poly(lactic acid-co-glycolic acid) (PLGA) microspheres were physically entrapped within the Pluronic hydrogel in order to modulate the local pH environment by acidic degradation by-products of PLGA microspheres. The PLGA microspheres were slowly degraded to create an acidic microenvironment, which facilitated the cleavage of an acid-labile ester-linkage in the biodegradable Pluronic hydrogel network. The presence of PLGA microspheres accelerated the degradation of the Pluronic hydrogel and enhanced the protein release rate when protein was loaded in the hydrogel.SEM image of photo-crosslinked Pluronic hydrogel entrapping PLGA microspheres.