基于脉冲微反装置的Au/HZSM-5催化剂上正丁烷反应性能研究

以HZSM-5沸石分子筛为载体,尿素为沉淀剂,采用常压沉积-沉淀法和负压沉积-沉淀法制备了系列Au/HZSM-5沸石催化剂并采用常规催化剂表征方法对其进行了表征.用脉冲微反装置评价了纯正丁烷(99.9%)在氢型和金改性的纳米HZSM-5催化剂上的反应活性和烯烃选择性.结果表明,在550℃下,负压沉积-沉淀法制备的不同金负载量的纳米HZSM-5催化剂上的转化率和烯烃选择性都远高于常压沉积沉淀法制备的催化剂.改性量为2.0%的Au/HZSM-5-A(负压)催化剂正丁烷转化率达到了58.0%、烯烃选择性为57.2%.脱氢和脱甲基活化是正丁烷的重要活化方式,也是影响其烯烃选择性的主要因素.金改性在提高正丁烷转化率的同时,也促进了正丁烷的脱氢和脱甲基活化.纳米HZSM-5因晶粒度小,孔道短和微孔扩散阻力低而有利于正丁烷转化.负压有利于清除HZSM-5内部的无定型杂质和脱气净化处理,有利于金的负载量和分散度.     

碱改性ZSM-5分子筛及脱硫性能的研究

用4 mol·L-1Na2CO3溶液处理ZSM-5分子筛[HZSM-5(C)],处理后的分子筛采用n(TPAOH)∶n(Si O2)=0.2∶1的TPAOH溶液进行二次晶化[HZSM-5(C-T)]。制备了Ni-Mo/HZSM-5(原粉)、Ni-Mo/HZSM-5(C)和Ni-Mo/HZSM-5(C-T)催化剂。在小型连续固定床反应器上,考察了Ni-Mo/HZSM-5,Ni-Mo/HZSM-5(C)和Ni-Mo/HZSM-5(C-T)催化剂的硫醚化反应性能。结果表明:Na2CO3处理形成了微-介孔多级孔HZSM-5分子筛,提高了硫醇转化率;TPAOH二次晶化,修复了分子筛的孔道,增加了介孔的数量,进一步提高了硫醇的转化率。考察了TPAOH二次晶化前后,HZSM-5分子筛的热稳定性和水热稳定性。结果表明:Na2CO3处理降低了HZSM-5分子筛的热稳定性和水热稳定性,而TPAOH二次晶化,提高了HZSM-5分子筛的热稳定性和水热稳定性。     

双功能WC/HZSM-5催化剂上正己烷芳构化反应性能

以HZSM-5(SiO2/Al2O3=38)为载体,偏钨酸铵为钨源制备了双功能催化剂WC/HZSM-5,考察了其催化正己烷芳构化反应性能,并采用X射线衍射、扫描电子显微镜、X射线能量散射谱和程序升温氨脱附等手段对催化剂进行了表征,探讨了制备方法和WC含量对WC/HZSM-5催化剂性能的影响.结果表明,采用原位还原碳化法制备的WC/HZSM-5(RC)催化剂上正己烷芳构化反应性能优于浸渍法制备的WC/HZSM-5(IP).5%WC/HZSM-5(RC)样品在反应初始阶段芳烃选择性为10.28%,而HZSM-5上的仅为2.56%.WC/HZSM-5(RC)催化剂上反应产物中轻质芳烃(苯、甲苯和二甲苯)含量增加,重质芳烃C9+含量降低,其催化性能优于Pt/HZSM-5催化剂.产物分布的变化可能是由于WC与分子筛间的协同作用所致.     

等级孔微孔-介孔Fe2O3/ZSM-5中空分子筛催化材料的制备及催化苄基化性能

ZSM-5分子筛具有极其均匀的孔道结构、 良好的形状选择性和催化活性及耐水热稳定性, 是一种高效、 绿色的固体催化剂, 被广泛应用于石油催化裂化、 精细化工和环境保护等领域. 但其单一的微孔结构大大降低了客体分子的流通扩散性, 导致由大分子参与的芳烃烷基化反应受到极大限制. 本文采用NaOH/四丙基氢氧化铵(TPAOH)混合碱处理微孔ZSM-5, 制备了具备高结晶度、 高比表面积的等级孔微孔-介孔ZSM-5中空分子筛材料, 该材料在保持微孔孔道良好水热稳定性和大量活性中心的同时, 还通过介孔的引入进一步促进反应物及产物的扩散, 使间三甲苯苄基化反应的转化率提高了3.8倍. 通过在等级孔微孔-介孔ZSM-5中空材料上负载Fe, 开发出了具有双功能的等级孔微孔-介孔Fe₂O₃/ZSM-5中空催化剂, 该催化剂在苯的苄基化反应中表现出优异的催化性能, 当Fe负载量(质量分数)为6.67%, 反应温度为75 ℃, 反应时间为15 min时, 转化率高达98.3%, 选择性为81.6%, 最终收率达到80.2%.     

Pt改性分子筛催化剂上丙烷与苯的烷基化反应

研究了不同分子筛负载的Pt催化剂上丙烷与苯的烷基化反应.结果表明,Pt/HZSM-5具有较好的催化性能.在0~0.3%范围内提高Pt负载量可以提高催化剂的催化活性和生成C9以及C10 芳烃的选择性,降低非芳烃产物的选择性.较低的反应温度、较高的苯/丙烷摩尔比和较高的空速有利于烷基芳烃的生成.     

MgO/HZSM-5中MgO分散状态和催化性能的关系

以硝酸镁、醋酸镁为前身物,通过浸渍法制备了不同系列MgO/ HZSM-5催化剂,用XRD、XPS方法研究了MgO在HZSM-5上的分散状态,用NH3-TPD方法考察了催化剂的酸性,用常压连续流动微型反应装置考察MgO/ HZSM-5在甲苯甲醇烷基化反应中的催化性能.发现前身物不同,MgO在HZSM-5上的分散状态也不同,催化剂的活性和选择性与MgO分散状态密切相关.MgO负载量相同时,在以硝酸镁为前身物制备的催化剂中,MgO在HZSM-5内外表面均有分散,催化剂的对位选择性较高,而活性较低;在以醋酸镁为前身物制备的催化剂中,MgO较多分布在HZSM-5外表面,催化剂的活性较高,但选择性较低.使用醋酸镁为前身物,通过二次浸渍和高温水汽处理,适当改变MgO在分子筛表面的分布并使孔道窄化,可在活性降低较少的情况下显著提高催化剂对二甲苯选择性.     

二维HZSM-5纳米片的合成及催化苯与稀乙烯烷基化制乙苯

采用晶种导向的方法, 以四丙基溴化铵为模板剂, 乙胺为矿化剂, 硅溶胶为硅源, 氯化铝为铝源, 60 nm Silicate-1为晶种, 于水热条件下合成了具有不同b轴厚度及硅铝比的二维 HZSM-5纳米片. 采用不同碱源对分子筛进行碱处理, 其中经NaOH处理以及NaOH与四丙基氢氧化铵(TPAOH)联合处理得到了二维多级孔HZSM-5纳米片. 利用X射线衍射(XRD)、 扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 Ar吸附-脱附、 氨-程序升温脱附(NH₃-TPD)、 X射线荧光光谱(XRF)和X射线光电子能谱(XPS)等手段对催化剂的结构和酸性进行了表征, 考察了硅铝比和b轴厚度对催化苯与稀乙烯烷基化反应的影响. 研究结果表明, 在360 ℃, 1.4 MPa, 苯烯比为6, 乙烯体积分数为15%, 乙烯质量空速(WHSV)为1.5 h^-1的反应条件下, 随着硅铝原子比从80提高至200, 苯的转化率略有下降, 乙基选择性保持在99.2%以上, 但甲苯及二甲苯选择性分别从0.11%和0.09%均下降至0.05%. 将不同b轴厚度的HZSM-5纳米片催化剂在苯烯比为1的条件下进行实验发现, 硅铝比为160的大晶粒HZSM-5催化剂失活严重, 反应50 h时苯的转化率从34.6%下降至8%, 二甲苯选择性达到0.37%; 而b轴厚度为100 nm的二维 HZSM-5纳米片作为催化剂时苯的转化率稳定在44.0%, 乙基选择性为94.8%, 二甲苯选择性下降至0.22%, 并在100 h内保持反应性能不变.     

HF改性的Pt/ZSM-5催化剂在苯和甲醇烷基化反应中的应用

以HF改性的Pt/ZSM-5为催化剂,研究了其在苯和甲醇烷基化反应的应用,并用XRD、NH₃-TPD、BET等表征方法研究了改性前后催化剂酸性和孔结构变化。 结果表明,经HF改性后,Pt/ZSM-5催化剂的酸性增强、酸量增加,苯和甲醇烷基化反应性能明显提升。 3%HF-0.2%Pt/ZSM-5催化剂催化苯和甲醇烷基化反应时,甲苯和二甲苯选择性达到92.20%。 但是,HF负载量大于6%时,HF脱除的部分骨架硅和骨架铝会堆积在催化剂孔道内部,限制了反应物和产物的扩散,造成其催化性能下降。 通过计算得到了HF改性的Pt/ZSM-5催化剂上苯和甲醇烷基化反应的活化能为118 kJ/mol。     

La改性HZSM-5分子筛催化剂甲醇转化制汽油反应性能研究

采用浸渍法制备了La改性HZSM-5分子筛催化剂,利用X射线衍射（XRD）、氮气吸附-脱附、氨气程序升温脱附（NH₃-TPD）以及吡啶吸附红外光谱（Py-FTIR）技术对催化剂进行表征,并在固定床微型反应评价装置上,在反应温度350℃,系统压力0.1 MPa,甲醇质量空速4.74 h^-1的条件下,考察La改性HZSM-5分子筛催化剂的甲醇转化制汽油反应性能。结果表明,La改性HZSM-5分子筛催化剂的酸量降低,比表面积和孔容减小。La负载量为4%时,其MTG反应性能最佳,催化剂的寿命和汽油收率分别由改性前的12 h和52.69%增加到16 h和59.28%。此外,随着La负载量的增加,汽油中芳烃含量显著降低,降幅达18%。     

新型Pd/HZSM-5-N催化剂的制备及其在苯甲醇氧化反应中的应用

以分子筛HZSM-5为前驱体,氨气为氮源,直接高温氮化制得掺氮分子筛HZSM-5-N(1);以Pd(OAc)₂为钯源,1为载体,采用溶胶-固载法制备了一系列不同钯负载量(α)的新型Pd^α/1催化剂,其结构和性质经SEM, FT-IR,元素分析,XRD, N₂-BET和ICP表征。以苯甲醇氧化成苯甲醛反应为探针反应,研究了α, Pd^α/1用量,反应时间和反应温度对Pd^α/1催化性能的影响。结果表明：在最优反应条件(Pd₂/1 40 mg,于120 ℃反应180 min)下,苯甲醇转化率为66.7%,苯甲醛选择性为92.9%。 Pd₂/1重复使用性能较好,循环使用5次,催化活性保持不变。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.