γ-Fe2O3纳米纤维的丙酮敏感特性

采用静电纺丝法制备了PVP/FeC₆H₅O₇复合纳米纤维, 并将复合纤维在500 ℃高温烧结3 h, X射线衍射分析(XRD)表明, 烧结后的产物为正尖晶石结构的γ-Fe₂O₃晶体. 扫描电子显微镜(SEM)观测结果表明, 制得了直径均匀、 连续的复合纳米纤维, 其平均直径约为1000 nm; 烧结后的γ-Fe₂O₃纳米纤维保持了其连续性, 但纤维发生了收缩, 直径较烧结前小, 平均约为600 nm. 比表面积分析表明, γ-Fe₂O₃纳米纤维比表面积为57.18 m²/g. 气敏性能测试结果表明, 230 ℃为γ-Fe₂O₃纳米纤维检测丙酮气体的最佳工作温度. 在此温度下, γ-Fe₂O₃纳米纤维对丙酮气体表现出高响应度[S=6.9, c(Acetone)=7.88×10⁴ mg/m³]和线性度(7.88×10²~1.58×10⁵ mg/m³浓度范围内). 同时, γ-Fe₂O₃纳米纤维气体传感器件还表现出良好的长期稳定性.     

ZIF-67衍生的花状Ga掺杂Co3O4用于增强三乙胺传感性能

基于Ga³⁺对Co-MOF(ZIF-67)进行掺杂的策略，衍生制备了具有花状结构的Ga掺杂Co₃O₄气敏材料，并应用于三乙胺(TEA)选择性气敏传感。采用X-射线衍射仪表征了气敏材料的晶体构型，结果表明，Ga离子成功地掺杂到Co₃O₄晶格中。采用扫描电镜以及透射电镜对气敏材料的微观形貌进行表征，结果表明，含有1%Ga掺杂比例的Co₃O₄具有更为疏松多孔的花状结构。采用X-射线光电子能谱以及氮气吸脱附测试对材料的氧空位含量以及比表面积进行表征，结果表明，含有1%Ga掺杂比例的Co₃O₄具有丰富的氧空位含量以及较大的比表面积。最后，采用CGS-8气敏测试分析系统对含有不同Ga掺杂比例的Co₃O₄气敏材料进行三乙胺选择性气敏测试，结果表明，Ga掺杂比例为1%的Co₃O₄气敏传感器显示出最优的TEA气敏响应特性，...     

平面型乙醇快速响应气敏传感器的制备

采用水热法合成了纳米In₂O₃颗粒,将其旋涂于陶瓷基片上经氮化处理获得InN基片,再对InN基片进行氧化,合成出气敏材料并在一种微型平面电极片上制备了传感器件.采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）仪、X射线光电子能谱（XPS）等手段对材料的形貌、组成进行了表征与分析,结果表明,最终获得了松枝状结构的InN-In₂O₃纳米复合材料.对器件的气敏性能进行了测试,发现基于此材料制备的平面型气敏传感器对乙醇气体具有良好的气敏性能：检测浓度为1.025 mg/m³（500 ppb）的乙醇蒸汽的灵敏度可达18;检测2.05 mg/m³（1 ppm）的乙醇的响应-恢复时间最快仅为1 s;最佳工作温度低,仅为50℃.     

偶氮苯-PVP复合薄膜光波导传感器检测苯乙烯

将掺杂偶氮苯（Azo）的聚乙烯吡咯烷酮（PVP）作为敏感试剂,利用旋转甩涂法将其固定在钾离子（K⁺）交换玻璃光波导表面,研制了Azo-PVP复合薄膜/K⁺交换玻璃光波导气敏元件,并对其气敏特性进行研究。实验结果表明,该敏感元件对苯乙烯蒸汽有较好的选择性响应,其最低检测浓度为1.0×10^-8体积比（V/V₀）,响应-恢复时间分别为9 s和24 s。在浓度1.0×10^-81.0×10^-3（V/V₀）范围内,气体浓度与输出光强度之间有较好的线性关系。     

基于二茂铁的两个查尔酮衍生物的合成及超快三阶非线性光学响应

二茂铁是合成新颖有机功能材料的基本单元之一。 本文设计并合成了两个基于二茂铁的同分异构查尔酮衍生物:1-二茂铁基-3-(噻吩-2-基)丙烯酮(a)和1-二茂铁基-3-(噻吩-3-基)丙烯酮(b)。 采用超快激光Z-扫描技术(脉宽180 fs,波长532 nm)测定了化合物a和b的三阶非线性光学性质。 结果表明,化合物a吸收系数β=-2.1×10^-12 m/W,折射率n₂=1.9×10^-19 m²/W,分子超极化率γ=5.37×10^-32 esu;化合物b:β=-1.2×10^-13 m/W,n₂=2.0×10^-19 m²/W,γ=4.48×10^-32 esu。 说明在飞秒激光激发下,电荷转移能够在化合物a和b分子内部快速进行,二者均具有优异的超快三阶非线性光学响应。 在B3LYP/6-311+G(d,p)理论水平下,计算了化合物a和b分子轨道能量、极化率和各基团在前线分子轨道中的占有率。 理论计算结果显示,二茂铁基团在化合物a和b前线分子轨道中占有率分别为97%和98%,对两化合物的非线性光学性能起主导作用。     

电/离子导体双包覆的LiNi0.8Co0.1Mn0.1O2锂离子电池阴极材料及其电化学性能

高镍三元材料LiNi_0.8Co_0.1Mn_0.1O₂ (NCM)比容量高且成本低, 但材料结构在电化学循环过程中的不稳定性影响了其大规模的应用, 可采用表面包覆的策略来改善材料的结构稳定性, 从而提高其电化学性能. 本工作结合高速固相包覆法和高温烧结法, 分别将电子导体氧化锡锑(ATO)和锂离子导体偏磷酸锂(LOP)共同包覆在NCM材料表面. 双包覆后的NCM材料的电子电导率从2.17×10^-3 Ѕ•cm^-1提高至1.02×10^-2 Ѕ•cm^-1, 锂离子扩散系数也从7.05×10^-9 cm²•s^-1提高至2.88×10^-8 cm²•s^-1. 同时, NCM表面的双包覆层可以在循环过程中阻止电极材料与电解液发生氧化还原反应, 抑制材料不利相变, 减少氧的析出, 稳定材料结构. 电化学性能测试表明, 经过表面包覆后, NCM材料在1 C (180 mA•g^-1)的电流下和2.7~4.3 V (vs. Li/Li⁺)的电压范围内, 循环150周后容量为161.1 mAh•g^-1, 保持率为87.1%, 而在10 C的充放电倍率下具有133 mAh•g^-1的可逆比容量.     

基于一维双螺旋链的锌配合物的合成与荧光性能

选择配体N,N'-双(3-吡啶)丙二酰胺(3-bpma)、1,4-对苯二乙酸(H₂pda)和硝酸锌在水热条件下,自组装制备了一个基于双螺旋链的三维超分子锌配合物[Zn(3-bpma)(pda)]_n(1),并通过红外光谱、元素分析、热重分析和X射线单晶衍射分析进行了晶体结构表征。 单晶结构分析表明标题锌配合物是正交晶系,Pna21空间群,晶胞参数a=1.62512(11) nm,b=1.15947(8) nm,c=1.19282(8) nm,α=90°,β=90°,γ=90°,V=2.2476(3) nm³,M_r=513.80,D_c=1.518 g/cm³,Z=4,F(000)=1056,R₁=0.0381,wR₂=0.0669。 金属锌离子被两种桥连配体3-bpma和pda连接形成一种一维双螺旋链状结构,相邻的链间进一步通过氢键作用拓展成为三维超分子网络结构。 标题锌配合物具有强荧光发射特性,而且其对不同的有机溶剂分子和金属离子有显著的荧光传感特性,可以作为检测硝基苯的高灵敏性荧光传感材料。 CCDC:1811967     

芘基查尔酮的合成及三阶非线性光学性质

合成了一种新的具有潜在应用价值的非线性光学(NLO)有机材料1-(芘-1-基)-3-(4-二甲氨基苯基)丙烯酮(PMAK),并通过 NMR、IR、MS和元素分析等技术手段进行了表征。 采用溶液Nd:YAG激光技术测定了PMAK的三阶非线性光学性质并确定了相关参数。 纳秒实验结果:折射率n₂=-3.5×10^-17 m²/W,吸收系数β=7.0×10^-10 m/W,极化率χ⁽³⁾=2.54×10^-11 esu,分子超极化率γ=3.44×10^-30 esu;皮秒实验结果:n₂=-2.8×10^-18 m²/W,β=8.3×10^-11 m/W,χ⁽³⁾=2.49×10^-12 esu,γ=3.33×10^-31 esu。     

Y掺杂的ZnO纳米纤维材料的制备及其气敏传感器作用机理

采用静电纺丝法成功制备了Y掺杂的ZnO纳米纤维.并通过X射线衍射(XRD),扫描电子显微镜(SEM),能量色散X射线(EDX),透射电子显微镜(TEM)以及热重差热分析(TG-DTA)等手段对样品的结构和形貌进行了表征分析.同时用纯的ZnO和Y掺杂的ZnO纳米纤维制备了传感器,对浓度为(1-200)×10^-6 (体积分数)丙酮的气敏特性进行了测试分析.测试结果表明,可以通过简单控制纳米纤维中Y的含量,来微调该传感器的气敏特性.同时也发现通过Y掺杂, ZnO纳米纤维对丙酮的气敏特性有所改善,表现出很高的响应.纯ZnO和Y掺杂ZnO制成的传感器对几种潜在干扰气体表现出良好的选择性,比如氨气、苯、甲醛、甲苯以及甲醇.本文最后也讨论了该传感器的气敏作用机理.     

亚磷酸锌无机-有机杂化化合物的合成与结构表征

在水热条件下, 以1,6-己二胺为模板剂合成了一个三维(3D)亚磷酸锌无机-有机杂化化合物(C₆N₂H₁₆)_0.5ZnHPO₃(ZnHPO-CJ15), 并对其单晶结构进行了解析. 结果表明, ZnHPO-CJ15晶体属单斜晶系, P2₁/c空间群, a=1.19587(7) nm, b=0.82766(5) nm, c=0.77756(5) nm, α=90.00°, β=95.8370(10)°, γ=90.00°, V=0.76562(8) nm³, Z=1. ZnHPO-CJ15具有层柱状结构, 其骨架结构是由ZnO₃N四面体和HPO₃假四面体连接构成的二维4×8元环网层结构, 层与层之间由1,6-己二胺分子与Zn配位柱撑连接形成三维结构.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.