介孔TiO2-ZnO复合薄膜的制备与表征

以三嵌段聚合物P123为模板剂, 以钛酸异丙酯和二水乙酸锌为无机前驱体, 利用溶胶-凝胶法和旋涂法成功地制备了不同ZnO含量的介孔TiO2-ZnO复合薄膜. 在ZnO前驱体摩尔分数为0~50％范围内获得薄膜质量较高的介孔TiO2-ZnO复合薄膜. 用小角XRD、扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)、能谱仪(EDS)、紫外-可见吸收光谱(UV-Vis)及X射线光电子能谱(XPS)对所得的复合薄膜进行了表征和分析. EDS和XPS等研究证明介孔薄膜为TiO2和ZnO的复合体系, 且ZnO前驱体含量的增加仍能保持TiO2-ZnO复合薄膜的均匀性. UV-Vis研究结果表明, 介孔复合薄膜的光学带隙宽度为3.45-3.58 eV, 随着ZnO含量的增加, 复合薄膜的紫外吸收蓝移.     

热分解双(2-氨基烟酸)锌(Ⅱ)制备的介孔微砖ZnO纳米颗粒的光催化活性(英文)

Hollow microblocks of [Zn(anic)_2], as a novel coordination compound, were synthesized using 2-aminonicotinic acid(Hanic) and zinc(Ⅱ) nitrate tetrahydrate. The chemical composition of the zinc complex, ZnC_(12)H_(10)N_4O_4, was determined by Fourier transform infrared(FTIR) spectroscopy and elemental analysis. The synthesized zinc complex was used as a precursor to produce ZnO nanostructures by calcination at 550 °C for 4 h. Morphological studies by scanning electron microscopy and transmission electron microscopy revealed the formation of porous microbricks of ZnO nanoparticles. N_2 adsorption-desorption analysis showed that the obtained ZnO microbricks possess a mesoporous structure with a surface area of 8.13 m~2/g and a pore size of 22.6 nm. The X-ray diffraction pattern of the final product proved the formation of a pure ZnO composition with a hexagonal structure. Moreover, FTIR analyses showed that the 2-aminonicotinic acid ligand peaks were absent after the calcination step. Diffuse reflectance spectroscopy was used to determine the band gap energy of the produced ZnO and it was about 3.19 eV. To investigate the photocatalytic activity of the porous ZnO nanostructure, a series of photocatalytic tests were carried out to remove Congo red, as a representative toxic azo dye, from aqueous solution. The results show that the product can be used as an efficient photocatalyst for waste water treatment with high degradation efficiency.     

Determination of the interface band alignment of Mg2Si/4H-SiC heterojuction for potential photodetector application

The Mg₂Si/4H-SiC heterojunction was prepared by radio frequency (RF) magnetron sputtering technique. The binding energies of Mg 2p, Si 2p, and C 1s core levels and the maxima of valence band were measured by X-ray photoelectron spectroscopy (XPS). Using the optical bandgap of Mg₂Si (0.78 eV) and 4H-SiC (3.25 eV), the band offsets of valence band (VBO) and conduction band (CBO) at Mg₂Si/4H-SiC interface were identified as 1.47 and 1.00 eV, respectively. The band alignment was evaluated to be type-I band alignment. The Mg₂Si/4H-SiC heterojunction could be a promising candidate for the infrared (IR) photodetector.     

Synthesis,Characterization and Photocatalytic Activity of Mg‐Impregnated ZnO–SnO2 Coupled Nanoparticles

ZnO–SnO₂ nanoparticles were prepared by coprecipitation method; then Mg, with different molar ratios and calcination temperatures, was loaded on the coupled nanoparticles by impregnation method. The synthesized nanoparticles were characterized by X‐ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray spectroscopy (EDX), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), and Brunauer–Emmett–Teller (BET) techniques. Based on XRD results, the ZnO–SnO₂ and Mg/ZnO–SnO₂ nanoparticles were made of ZnO and SnO₂ nanocrystallites. According to DRS spectra, the band gap energy value of 3.13 and 3.18 eV were obtained for ZnO–SnO₂ and Mg/ZnO–SnO₂ nanoparticles, respectively. BET analysis revealed a Type III isotherm with a microporous structure and surface area of 32.051 and 49.065 m² g^?1 for ZnO–SnO₂ and Mg/ZnO–SnO₂, respectively. Also, the spherical shape of nanocrystallites was deduced from TEM and FESEM images. The photocatalytic performance of pure ZnO–SnO₂ and Mg/ZnO–SnO₂ was analyzed in the photocatalytic removal of methyl orange (MO). The results indicated that Mg/ZnO–SnO₂ exhibited superior photocatalytic activity to bare ZnO–SnO₂ photocatalyst due to high surface area, increased MO adsorption and larger band gap energy. Maximum photocatalytic activity of Mg/ZnO–SnO₂ nanoparticles was obtained with 0.8 mol% Mg and calcination temperature of 350°C.     

Efficient photocatalytic degradation of phenol over Co3O4/BiVO4 composite under visible light irradiation

Co3O4/BiVO4 composite photocatalyst with a p-n heterojunction semiconductor structure has been synthesized by the impregnation method. The physical and photophysical properties of the composite photocatalyst have been characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transimission electron microscopy (TEM), BET surface area, and UV-visible diffuse reflectance spectra. Co is present as p-type Co3O4 and disperses on the surface of n-type BiVO4 to constitute a heterojunction composite. The photocatalyst exhibits enhanced photocatalytic activity for phenol degradation under visible light irradiation. The highest efficiency is observed when calcined at 300 degrees C with 0.8 wt % cobalt content. On the basis of the calculated energy band positions and PL spectra, the mechanism of enhanced photocatalytic activity has been discussed.     

Fabrication of composite photocatalyst g-C3N4-ZnO and enhancement of photocatalytic activity under visible light

The g-C(3)N(4)-ZnO composite photocatalysts with various weight percents of ZnO were synthsized by a simple calcination process. The photocatalysts were characterized by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HR-TEM), UV-vis diffuse reflection spectroscopy (UV-vis), X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA). The PXRD and HR-TEM results show that the composite materials consist of hexagonal wurzite phase ZnO and g-C(3)N(4). The solid-state UV-vis diffuse reflection spectra show that the absorption edge of the composite materials shifts toward the lower energy region and to longer wavelengths in comparison with pure ZnO and g-C(3)N(4). Remarkably, the photocatalytic activity of g-C(3)N(4)-ZnO composites has been demonstrated, via photodegradation of Methyl Orange (MO) and p-nitrophenol experiments. The photocatalytic activity of g-C(3)N(4)-ZnO for photodegradation of Methyl Orange and p-nitrophenol under visible light irradiation was increased by over 3 and 6 times, respectively, to be much higher than that of single-phase g-C(3)N(4), clearly demonstrating a synergistic effect between ZnO and g-C(3)N(4). The concentrations of Zn(2+) in g-C(3)N(4)-ZnO system after a photocatalytic reaction at various reaction times were found to be much lower than those for a ZnO system under the same reaction conditions, indicating that the g-C(3)N(4)-ZnO composite possesses excellent long-term stability for a photocatalytic reaction in aqueous solutions. Furthermore, a synergistic photocatalysis mechanism between ZnO and g-C(3)N(4) was proposed based on the photodegradation results. Such obviously improved performance of g-C(3)N(4)-ZnO can be ascribed mainly to the enhancement of electron-hole separations at the interface of ZnO and g-C(3)N(4).     

Optical and photocatalytic properties of heavily F(-)-doped SnO2 nanocrystals by a novel single-source precursor approach

Heavily F-doped SnO(2) nanocrystals were successfully prepared by a novel synthetic approach involving low-temperature oxidation of a Sn(2+)-containing fluoride complex KSnF(3) as the single-source precursor with H(2)O(2). The F-doped SnO(2) powder was characterized by powder X-ray diffraction, TG-MS, BET surface area, diffuse reflectance spectroscopy, XPS, PL, FTIR spectroscopy, Raman spectroscopy, EPR spectroscopy, SEM, and TEM. Broadening of the diffracted peaks, signifying the low crystallite size of the products, was quite evident in the powder X-ray diffraction pattern of SnO(2) obtained from KSnF(3). It was indexed in a tetragonal unit cell with lattice constants a = 4.7106 (1) ? and c = 3.1970 (1) ?. Agglomeration of particles, with an average diameter of 5-7 nm, was observed in the TEM images whose spotwise EDX analysis indicated the presence of fluoride ions. In the core level high-resolution F 1s spectrum, the peak observed at 685.08 eV was fitted by the Gaussian profile yielding the fluoride ion concentration to be 21.23% in the SnO(2) lattice. Such a high fluoride ion concentration is reported for the first time in powders. SnO(2):F nanocrystals showed greater thermal stability up to 300 °C when heated in a thermobalance under flowing helium, after which generation of small quantities of HF was observed in the TG coupled mass spectrometry analysis. The band gap value, estimated from the Kubelka-Munk function, showed a large shift from 3.52 to 3.87 eV on fluoride ion doping, as observed in the diffuse reflectance spectrum. Such a large shift was corroborated to the overdoped situation due to the Moss-Burstein effect with an increase in the carrier concentration. In the photoluminescence (PL) spectrum, SnO(2):F nanocrystals exhibited a broad green emission arising from the singly ionized oxygen vacancies created due to higher dopant concentration. The evidence for singly ionized vacancies was arrived from the presence of a signal with a g value of 1.98 in the ESR spectrum of SnO(2):F at room temperature. The disordered nature of the rutile lattice and the enormous oxygen vacancies created due to fluoride ion doping were evident from the broad bands observed at 455, 588, and 874 cm(-1) in the room-temperature Raman spectrum of SnO(2):F. As the consequence of the oxygen vacancies, F-doped SnO(2) was examined for the function as a photocatalyst in the degradation of aqueous RhB dye solution under UV irradiation. A very high photocatalytic efficiency was observed for the F-doped SnO(2) nanocrystals as compared to pure SnO(2). The BET surface area of pure SnO(2) was quite high (207.81 m(2)/g) as compared to the F-doped SnO(2) nanocrystals (45.16 m(2)/g). Pore size analysis showed a mean pore diameter of 1.97 and 13.97 nm for the pure and doped samples. The increased photocatalytic efficiency was related to the very high concentration of oxygen vacancies in SnO(2) induced by F doping.     

Ag/ZnO纳米纤维的制备及光催化性能

采用静电纺丝技术及煅烧法制备了氧化锌纳米纤维, 然后采用水热法将银纳米颗粒负载到了氧化锌纳米纤维表面. 利用X射线衍射(XRD)、 X射线光电子能谱(XPS)、 能量色散X射线光谱(EDX)、 扫描电子显微镜(SEM)及透射电子显微镜(TEM)等技术对合成的Ag/ZnO纳米纤维的结构和组成进行了表征. SEM结果表明, 直径在5~100 nm之间的银纳米颗粒附着在直径在80~330 nm之间的氧化锌纤维表面形成了异质结构. 以常见的有机污染物甲基橙、 亚甲基蓝和罗丹明B等为降解底物, 对Ag/ZnO纳米纤维的光催化性能进行了表征. 结果表明, 负载银纳米颗粒后, 复合催化剂的光催化性能明显提高.     

Tailoring the optical property by a three-dimensional epitaxial heterostructure: a case of ZnO/SnO2

Epitaxial growth, as a best strategy to attain a heterostructure with a well-defined and clean interface, usually takes place on a planar substrate. In this paper, using a ZnO/SnO2 core-shell heterostructure as an example, we demonstrate the possibility of establishing a three-dimensional epitaxial interface between two materials with different crystal systems for the first time and show possible tailoring optical properties by building the heteroepitaxial crystal interface. The characterization results of element mapping, high-resolution transmission electron microscopy, and selected area electric diffraction reveal that the as-prepared ZnO/SnO2 heterostructure has a tetrapod-like ZnO core and a SnO2 shell with 15-30 nm, and their special epitaxial relation is (010)SnO2//(010)ZnO and [100]SnO2//[0001]ZnO. Such three-dimensional epitaxy between the ZnO core and SnO2 shell is quite different from the usual planar epitaxy or three-dimensional epitaxy between materials having the same crystal structure. A rational model of such complicated epitaxy has been proposed through investigating the certain structural comparability between the wurtzite ZnO and rutile SnO2 crystals. The as-prepared T-ZnO/SnO2 epitaxial heterostructure exhibits unique luminescence properties in contrast with individual tetrapod ZnO and SnO2 nanostructures, in which the epitaxial interface induces new luminescence properties. This result may inspire great interest in exploring other complicated epitaxy systems and their potential applications in laser, gas sensor, solar energy conversion, photo catalysis, and nanodevices in the future.     

Flower-like Bi2WO6/ZnO composite with excellent photocatalytic capability under visible light irradiation

The photocatalytic ability of ZnO is improved through the addition of flower-like Bi₂WO₆ to prepare a Bi₂WO₆/ZnO composite with visible light activity. The composite is characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy with UV–vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy and N₂ adsorption-desorption isotherms. After modification, the band gap energy of Bi₂WO₆/ZnO is reduced from 3.2 eV for ZnO to 2.6 eV. Under visible light irradiation, the Bi₂WO₆/ZnO composite shows an excellent photocatalytic activity for degrading methylene blue (MB) and tetracycline. The photo-degradation efficiencies of (0.3:1) Bi₂WO₆/ZnO for MB and tetracycline are approximately 246 and 4500 times higher than those of bare ZnO, respectively, and correspondingly, the photo-degradation rates for the two pollutants are approximately 120 and 200 times higher than those with bare ZnO, respectively. Moreover, the photocatalyst of (0.3:1) Bi₂WO₆/ZnO exhibits a higher transient photocurrent density of approximately 4.5 μA compared with those of bare Bi₂WO₆ and ZnO nanoparticles. The successful recombination of Bi₂WO₆ and ZnO enhances the photocatalytic activity and reduces the band gap energy of ZnO, which can be attributed to the effective separation of electron–hole pairs. Active species trapping experiments display that [O₂]^? is the major species involved during photocatalysis rather than ?OH and h⁺. This study provides insight into designing a meaningful visible-light-driven photocatalyst for environmental remediation.     

Estimation of band alignment at CdS/Cu2ZnSnS4 hetero-interface by direct XPS measurements

This paper aims to estimate the band alignment to CdS/CZTS hetero-interface by direct X-ray photoelectron spectroscopy (XPS) measurements. XPS was used to determinate the valence-band offset (VBO) directly by determining the valence band positions at the hetero-interface. The conduction band offset (CBO) value was estimated based on the band gap measurements by UV/Visible spectroscopy and VBO measurements. The position of valence band (VB) changes close to the CdS-CZTS interface and the CBO is cliff-like. The band alignment diagram indicates that the CdS-CZTS interface heterojunction is type II.     

Liquid crystal alignment properties on surface-reformed solution-derived lanthanum-doped zinc oxide films

Liquid crystal (LC) alignment characteristics were investigated using a solution-derived lanthanum-doped zinc oxide (La:ZnO) film that was exposed to various intensities of ion-beam (IB) irradiation. At an IB intensity of 1700 eV, uniform and homogeneous LC alignment was achieved, as revealed by cross-polarized optical microscopy and pre-tilt angle measurement. Field-emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to verify that the IB irradiation induced physical and chemical surface reformation of the La:ZnO film that relate to LC alignment. FE-SEM and AFM revealed that the IB irradiation reformed the existing surface structure into a new structure with an altered surface roughness. The XPS results showed that the van der Waals force with anchoring energy increased as the IB intensity increased, and this profoundly affected the state of LC alignment. The capacitance-voltage (C-V) hysteresis curve was measured as a function of IB intensity to characterize the accumulated charge as a residual DC. Nearly zero C-V hysteresis was achieved at an IB intensity of 1700 eV. Therefore, a solution-derived La:ZnO film with an IB intensity of 1700 eV has great potential for high-quality LC applications.     

From Zn-Al layered double hydroxide to ZnO nanostructure:Gradually etching by sodium hydroxide

Zn-Al layered double hydroxide(LDH) was used as precursor to produce ZnO nanostructures through dissolution of aluminum hydroxide in caustic soda.The Zn-Al LDH could transform into different nanostructures of ZnO on LDH nanosheets and even pure ZnO nanorods under various NaOH concentration.The formed ZnO nanorods vertically aligned on both LDH sides.UV-vis diverse reflectance spectra show that the obtained ZnO nanorods have a band gap of approximately 3.05 eV.Such ZnO/LDH nanostructures might be used as photocatalyst in the organic pollutant decomposition.     

Photodegradation of Rhodamine B on Sulfur Doped ZnO/TiO2 Nanocomposite Photocatalyst under Visible-light Irradiation

Sulfur doped ZnO/TiO₂ nanocomposite photocatalysts were synthesized by a facile sol‐gel method. The structure and properties of catalysts were characterized by X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), UV‐vis diffusive reflectance spectroscopy (DRS) and N₂ desorption‐adsorption isotherm. The XRD study showed that TiO₂ was anatase phase and there was no obvious difference in crystal composition of various S‐ZnO/TiO₂. The XPS study showed that the Zn element exists as ZnO and S atoms form SO^2?₄. The prepared samples had mesoporosity revealed by N₂ desorption‐adsorption isotherm result. The degradation of Rhodamine B dye under visible light irradiation was chosen as probe reaction to evaluate the photocatalytic activity of the ZnO/TiO₂ nanocomposite. The commercial TiO₂ photocatalyst (Degussa P25) was taken as standard photocatalyst to contrast the prepared different photocatalyst in current work. The improvement of the photocatalytic activity of S‐ZnO/TiO₂ composite photocatalyst can be attributed to the suitable energetic positions between ZnO and TiO₂, the acidity site caused by sulfur doping and the enlargement of the specific area. S‐3.0ZnO/TiO₂ exhibited the highest photocatalytic activity under visible light irradiation after Zn amount was optimized, which was 2.6 times higher than P25.     

反蛋白石结构ZnO@PDA用于增强光催化产H2O2性能

利用太阳能驱动生产高能量密度的H₂O₂太阳能燃料引起了广泛关注,但目前光催化剂缓慢的动力学限制了其实际应用。本文制备一种聚多巴胺(PDA)改性的反蛋白石结构ZnO(ZnO@PDA)光催化剂,用于可持续性的光催化产H₂O₂。由于电子的转移,因此当PDA与ZnO接触后,会在界面处形成一个从PDA指向ZnO的内建电场。在内建电场和能带弯曲的驱动下,ZnO导带中的光生电子与PDA最高占据分子轨道(HOMO)中的空穴复合,符合梯型异质结的电荷转移和分离途径。这种独特的梯型异质结确保了有效的电子或空穴的分离并且留存下具有强氧化还原能力的光生载流子。此外,与纯ZnO相比,反蛋白石结构的ZnO@PDA具有更强的光吸收能力。实验表明,归因于光吸收能力的提高,光生载流子的有效分离和强氧化还原能力,负载0.03% (原子分数) PDA的ZnO样品具有最佳的产H₂O₂性能(1011.4 μmol·L^-1·h^-1),分别是纯ZnO和PDA的4.4和8.9倍。     

异质结型AgBr/CuO光催化剂的合成、 光催化活性及再生

采用沉淀法制备了具有p-n异质结结构的AgBr/CuO可见光催化剂, 对其结构进行了表征, 通过甲基橙溶液的降解率评价了AgBr/CuO的光催化活性, 并通过活性物种测试及能带结构分析推测了其光催化机理, 采用3%(质量分数)溴水对使用后的AgBr/CuO进行了再生处理. 结果表明, 在可见光照射下, 0.1 g AgBr/CuO光催化剂30 min对甲基橙溶液(初始浓度为15 mg/L)的降解率高达92%, 远高于同等条件下的AgBr. AgBr/CuO光催化活性提高的原因是AgBr与CuO的复合一方面使催化剂的禁带宽度变宽, 提高了光生电子与光生空穴的氧化还原能力; 另一方面, 在两者之间形成了p-n型异质结结构, 有利于光生电子的转移及光生电子与空穴的分离. 采用绿色环保的溴水再生法可显著恢复催化剂的光催化活性.     

Multifunctional silicene/CeO2 heterojunctions: Desirable electronic material and promising water-splitting photocatalyst

The first-principles calculations demonstrate that covalently bonded (cb) heterojunction and van der Waals (vdW) heterojunction can coexist in silicene/CeO₂ heterojunctions, due to the different stacking patterns. Especially, the cb heterojunction with band gap of 1.97 eV, forms a type-II heterojunction, exhibits good redox performance and has high-effective optical absorption spectra, thus it is a promising photocatalyst for overall water splitting. Besides, for the vdW heterojunction, the Dirac cone of silicene is well kept on CeO₂ semiconducting substrate, with a considerable energy gap of 0.43 eV, which can be an ideal material in building silicene-based electronic device. These results may open a new gateway in both of nanoelectronic device and energy conversion for silicene/CeO₂ nanocomposites.     

Preparation and characterization of sulfur-modified mesoporous titania photocatalyst

Sulfur-modified mesoporous titania (S-MTiO₂) was investigated as a potential photocatalyst under visible light. The photocatalyst was prepared by template method using thiourea and tetrabutyl titanate (Ti(OC₄H₉)₄) as precursors and Pluronic P123 as template. The photoabsorbance of as-prepared photocatalyst was measured by UV-vis absorption spectroscopy, which confirmed the extension of absorption into the visible region. The microstructure of S-MTiO₂ was characterized using X-ray diffraction (XRD) and N₂ adsorption-desorption measurements. The micro crystal of the S-doped photocatalyst consisted of anatase phase and no significant influence on the nature of crystal formation. X-ray photoelectron spectroscopy (XPS) measurements indicated the presence of C in the prepared photocatalyst in addition to S. The photo-catalytic performance was studied by photodegradation methyl orange (MO) in water under visible light irradiation. The calcination temperature and the doping content influenced the photoactivity.     

水热法制备Fe3+改性的SnO2纳米颗粒

采用水热法制备了Fe3+改性的SnO2纳米颗粒, 通过XRD、BET、TEM、FT-IR和紫外-可见漫反射光谱(DRS)对其结构和光学性质进行研究. 结果表明, 水热过程实现了氧化锡的直接晶化, 产物为金红石结构, Fe3+进入SnO2的晶格之中形成固溶体. 这种方法制备的Fe3+改性的SnO2纳米颗粒为单分散状态, 粒径分布均匀, 纯的SnO2未焙烧前平均粒径为6.0 nm, 随着Fe3+添加量的增大, 样品的粒径减小. BET显示纯的SnO2样品比表面积为206.1 m2•g−1, 随着Fe3+添加量增大, 产物的比表面积增大, 同时样品的紫外-可见吸收发生红移.     

Graphene/BiOI composites synthesized via the oil bath method and their application for efficient photocatalytic degradation of methyl orange under visible light irradiation

An efficient and simple oil bath method for rapid synthesis of graphene/BiOI as visible light active photocatalyst was described. The resultant graphene/BiOI composites were characterized by different techniques, including scanning electron microscopy, X-ray diffraction, and ultraviolet-visible diffuse reflectance spectroscopy. The photocatalytic activity of the as-prepared graphene/BiOI composites for methyl orange degradation was also investigated under visible light irradiation. The results show that BiOI and graphene taken with a mass ratio of 100: 1 exhibited the highest photocatalytic efficiency, which is two times that of pure BiOI. Part of this effect results from higher specific surface area that provides an increased number of active sites. A relatively narrow band gap (2.08 eV) formed in the heterostructure can also contribute to this effect. A suggestion of the photocatalytic mechanism was also offered.