立方晶型Sb2O3纳米晶的合成及光催化性能

采用沉淀法合成了立方晶型Sb2O3纳米晶,通过X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和电子自旋共振谱(ESR)等对样品进行了详细的表征。以紫外光光催化降解甲基橙为反应模型评价了样品的光催化性能。结果表明:沉淀法合成的立方晶型Sb2O3纳米晶颗粒小,表现出良好的光催化性能。对立方晶型Sb2O3纳米晶光催化降解甲基橙的原因进行了探讨,并提出了降解甲基橙的反应机理。     

纳米晶CuLa3Se5微波溶剂热合成及结构研究

采用微波溶剂热法合成纳米晶CuLa3Se5,具有快速,节能、纯度高、粒度小(平均粒径为20～30 nm)等优点.通过X射线粉末衍射(XRD)、透射电子显微镜(TEM)、扫描电镜能谱分析(EDS)和X射线光电子能谱(XPS)等手段表征其组成.讨论了微波溶剂热合成纳米晶的机制.漫反射紫外-可见吸收光谱(UV-Vis)表明标题化合物禁带宽度为2.27 eV,具有优良的半导体性能.     

V^5＋离子掺杂纳米氧化铈的合成与表征

以硝酸铈、柠檬酸和偏钒酸铵为原料,采用溶胶-凝胶(sol-Gel)法制备了V5+离子掺杂纳米CeO2粉体.利用X射线粉晶衍射(XRD)和 扫描电镜(SEM)等方法研究了合成反应条件(焙烧温度、V5+掺入量等)对合成物的微观结构、物相组成以及性能的影响.XRD分析表明所合成的CeO2纳米晶粒具有空间群符号为Fm3m的立方晶体结构.随焙烧温度的升高,合成的CeO2晶粒结晶度增高.对甲基蓝的光催化降解试验表明,纳米CeO2对甲基蓝具有较好的光催化降解效果,焙烧温度对纳米CeO2的光催化活性有较大影响,适量V5+的掺入有利于提高纳米 CeO2的光催化降解效果,掺1%V5+离子的CeO2光催化降解甲基蓝6 h,其降解率可达89%以上.     

低共熔溶剂中纳米氧化锌的制备及形貌调控

分别以工业氧化锌、氯化锌和草酸锌为锌源,氯化胆碱-尿素低共熔溶剂为溶剂,通过沉淀法制备了不同结构和形貌的纳米氧化锌。通过X射线衍射仪(XRD)、扫描电子显微镜(SEM)和甲基橙光催化降解对样品进行了表征,分析了锌源变化对产物形貌的影响以及不同形貌氧化锌形成过程中前驱体的调控作用及反应机理。并将制备的不同形貌氧化锌应用于光催化降解甲基橙。结果表明制备的由纳米晶组装而成的厚块状Zn O纳米结构对甲基橙有良好的光催化性能。     

偏锡酸锌纳米微粒的水热法制备及其对甲基橙降解的光催化性能

以醋酸锌和氯化锡为原料,以聚甲基丙烯酸钠(PMA)为表面活性剂,利用水热法合成了偏锡酸锌(ZnSnO3)纳米微粒;采用X射线衍射仪、傅立叶变换红外光谱仪、扫描电镜等分析了ZnSnO3纳米微粒的晶相、表面组成、形貌;并测定了ZnSnO3纳米微粒对甲基橙溶液的光催化降解性能.结果表明,所得ZnSnO3纳米微粒粒径约为20nm,表面存在羧基;其对pH=2的甲基橙溶液的光催化降解效果较好,甲基橙的初始浓度越低,降解效果越明显;随着催化剂用量的增加,降解效率逐渐增大.此外,循环催化试验结果表明ZnSnO3纳米微粒具有较好的催化稳定性.     

稀土离子掺杂的AgLa(WO4)2枝状纳米材料的合成与上转换发光性质

通过无模板的水热方法合成了AgLa(WO4)2树枝状纳米晶,没有表面活性剂等模板的介入,使反应变得简捷、绿色和经济. 综合利用多种测试手段对所得材料进行了表征,如X-射线粉末衍射,扫描电子显微镜,透射电子显微镜等,并根据实验结果的分析提出了扩散限制生长（DLA,diffusion-limited aggregation）模型. AgLa(WO4)2树枝状纳米晶可以作为稀土离子掺杂的主体材料,这种掺杂稀土离子（Yb3+, Er3+, Tm3+）的纳米晶在980 nm激光激发下展示丰富的上转换发光颜色. 根据上转换光谱详细研究了AgLa(WO4)2:RE3+树枝状纳米晶在980 nm激光激发下的上转换发光性质和发光机理.     

海绵状纳米结构TiO2膜的制备及其光催化活性

采用电化学阳极氧化法在钛表面构筑了海绵状纳米结构TiO2膜. 应用扫描电子显微镜(SEM)和X射线衍射(XRD)对膜层的形貌和晶型进行了分析和表征, 考察了阳极氧化时间对膜层厚度的影响, 并通过海绵状纳米结构TiO2膜对甲基橙的光催化降解研究了膜层厚度与光催化活性的关系. 结果表明, 海绵状纳米结构TiO2膜对甲基橙具有光催化降解作用, 而且随着膜层厚度的增加, 光催化降解速率显著增大, 厚度为2.2 μm的海绵状纳米结构TiO2膜对甲基橙的光催化降解速率是厚度为480 nm的6.4倍.     

石墨烯-二氧化钛复合催化剂对光催化性能的提高(英文)

以石墨烯氧化物和钛酸四丁酯为原料,通过水热法、无氧煅烧转晶合成了graphene-TiO2复合催化剂,并采用透射电镜、X射线衍射、拉曼光谱和X射线光电子能谱等手段对其进行了表征.结果表明,TiO2全部为锐钛矿晶型,呈纳米颗粒状附着在薄膜状的graphene表面.以亚甲基蓝为目标物,评价了graphene-TiO2催化剂的光催化性能.结果表明,graphene-TiO2的光催化降解能力明显优于相同方法制备的纳米TiO2颗粒,且具有较好的稳定性,空穴在降解过程中起主要作用,碱性溶液更有利于催化剂对MB的降解.     

F掺杂制备具有高暴露(001)晶面的BiOCl纳米片及其光催化性能

采用溶剂热-煅烧法,通过F掺杂合成了一系列具有高暴露(001)晶面的BiOCl纳米片。应用X射线衍射、N_2物理吸附、扫描电子显微镜、透射电子显微镜、X射线光电子能谱、紫外可见漫反射光谱、红外光谱和光电流响应等物理化学方法对合成的样品进行了表征分析。结果表明,掺杂适量的F可以促进BiOCl(110)优势晶面的生长,形成高暴露(001)晶面,同时可抑制BiOCl晶粒的长大,并增大BiOCl纳米片的比表面积和提高其表面羟基的数量。在模拟太阳光下,光催化降解偶氮染料罗丹明B结果表明,F掺杂能显著提高BiOCl对罗丹明B的光催化降解活性。其中F_(1.0)-BiOCl对罗丹明B的降解速率是BiOCl的2.67倍。此外,F_(1.0)-BiOCl对酸性橙Ⅱ的光催化降解活性是商业光催化剂P25(TiO_2)的1.24倍。F掺杂引起光催化活性大幅提升的主要原因是,高暴露(001)晶面的生成提升了BiOCl纳米片对染料的吸附性能,同时加快了光生e~-和h~+分离。     

(Ni-Mo)/TiO2纳米薄膜光催化降解刚果红的性能与机理

用恒电流复合电沉积方法制备(Ni-Mo)/TiO2薄膜,以扫描电子显微镜(SEM)、X射线衍射(XRD)、拉曼(Raman)光谱和紫外-可见漫反射光谱(UV-VisDRS)对薄膜的表面形貌、晶相结构和光谱特性进行了表征,以刚果红为模拟污染物对薄膜的光催化性能进行了测定,并讨论了刚果红溶液的pH值对薄膜光催化活性的影响.采用循环伏安技术和向溶液中加入活性物种捕获剂的方法对薄膜光催化降解机理进行了探索.结果表明:(Ni-Mo)/TiO2薄膜是由粒径为50-100nmTiO2纳米粒子相和纳米晶Ni-Mo固溶体相构成的复合薄膜.薄膜具有较高的光催化活性,卤钨灯照射80min后,复合薄膜光催化刚果红的降解率是多孔TiO2(DegussaP25)/ITO(氧化铟锡)纳米薄膜的2.43倍.(Ni-Mo)/TiO2薄膜光催化活性的提高主要归因于薄膜层中有效形成的(Ni-Mo)/TiO2异质结和良好的电子通道,以及Ni-Mo纳米晶合金对溶解氧和激发电子还原反应的催化作用.分别给出了在紫外和可见光下薄膜光催化降解刚果红的反应机理.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.