紫外光照射制备具有光学活性的银纳米粒子

以脱氧胆酸钠(NaDC)为还原剂、稳定剂,经紫外光辐照AgNO3溶液在室温下制备出尺寸30 nm左右的类球形的银纳米粒子。用紫外-可见光谱、透射电镜、圆二色谱和傅立叶变换红外光谱等测试手段对所制备的脱氧胆酸钠包裹的银纳米粒子进行了表征。红外光谱结果表明,在紫外光激发下,脱氧胆酸钠甾环上12α-OH发生氧化反应,同时还原Ag+为单质银,并聚集生成银纳米粒子。溶液的pH值对光化学氧化还原反应速度有着重要的影响,增加溶液的pH值,Ag+的还原反应速度明显加快。在吸附在银粒子表面的脱氧胆酸钠的手性氛围诱导下,生成的银纳米粒子在其表面等离子体共振区域出现手性信号。     

载银羟基磷灰石抗菌粉体和陶瓷的制备及抗菌性能

采用水热法一步合成载银羟基磷灰石抗菌粉体(Ag-HA),并将其应用于抗菌陶瓷的制备。研究结果表明水热条件下HA实际载银量与AgNO₃加入量存在较好的线性关系。XRD和TEM分析结果显示Ag-HA与HA具有相同的晶体结构,水热条件下Ag⁺取代Ca²⁺在HA晶体中的位置,生成Ag_xCa_10-x(PO₄)₆(OH)₂。Ag-HA长度随Ag⁺掺入量的增加而增大,当Ag⁺掺入量增加至1.50%时,Ag-HA由棒状生长为晶须状。选择4.50% Ag-HA作为抗菌粉体,其掺入量为9wt%时,陶瓷的抗菌率>99.9%,此时釉料中Ag₃PO₄含量为0.56%,低于目前研究中釉料中Ag₃PO₄添加量(2wt%~4wt%),不但在一定程度上解决了抗菌陶瓷产品成本较高的问题,而且满足JC/T 897-2002(抗菌陶瓷制品抗菌性能)对抗菌陶瓷抗菌性能的要求。     

K+掺杂双钙钛矿Cs2AgInCl6的发光性质

采用固相球磨法制备了K⁺掺杂双钙钛矿Cs₂AgInCl₆纳米材料,该方法无需配体辅助,绿色环保。通过X射线衍射和拉曼光谱对晶体结构进行研究,通过激发光谱、发射光谱和时间分辨光谱对其发光性能进行研究。结果表明,Cs₂AgInCl₆为立方晶体,属于Fm3m空间群,由于宇称禁戒跃迁,其荧光量子产率(PLQY)低,小于0.1%。低于60%的K⁺掺杂主要取代Ag⁺的位置,引起Cs₂AgInCl₆的晶格膨胀,消除了晶格结构的反演对称性,打破了宇称禁戒跃迁,掺杂后Cs₂AgInCl₆的光致发光强度显著增强。K⁺的最佳掺杂比例为40%,Cs₂Ag_0.6K_0.4InCl₆材料发射中心波长为640 nm,半高宽为180 nm,平均荧光寿命达到29.2 ns,PLQY达到10.5%。当K⁺掺杂比例超过60%,K⁺开始取代Cs⁺的位置,产物发生相变,出现立方相的Cs_2-xK_1+x-yAg_yInCl₆和单斜相的Cs_2-xK_1+xInCl₆产物,这些产物由于强电子-声子耦合,非辐射复合占据主导地位。     

载银sod基纳米分子筛的合成及抗菌性能

采用两步法合成了sod基系列分子筛(EMT、FAU、SOD),并通过离子交换法引入Ag⁺得到载银分子筛,通过X射线衍射(XRD)、扫描电子显微镜(SEM)证明离子交换前后分子筛骨架结构和晶粒尺寸没有发生明显变化;通过红外光谱(IR)、热重(TG)证明制得的载银分子筛具有良好的稳定性;对获得的载银分子筛进行了Ag⁺释放实验与抗菌能力测试,考察了分子筛种类和晶粒尺寸对抗菌性能的影响。结果表明具有笼状结构的FAU与EMT分子筛因可储存更多的Ag⁺而具有更好的抗菌性能,而具有超笼结构的FAU分子筛抗菌性能最优。通过对比不同晶粒尺寸载银FAU分子筛抗菌数据发现,晶粒尺寸为100 nm的载银FAU分子筛因外表面丰富的抗菌活性位点以及其内部可以储存并不断释放Ag⁺而具有最优的抗菌性能和抗菌寿命。而晶粒尺寸为10 nm的载银FAU分子筛由于晶粒尺寸较小、外比表面积大、扩散路径短,Ag⁺的释放速率最快,抗菌效率最高。     

双钙钛矿型Ca2Gd1-xTaO6：xTb3+绿色荧光粉的合成与荧光性质

通过高温固相法合成了双钙钛矿型Ca₂Gd_1-xTaO₆：xTb³⁺（CGTO：xTb³⁺）绿色荧光粉。采用X射线衍射、扫描电镜、荧光光谱、荧光衰减曲线、量子效率（η）测试分别表征了CGTO： xTb³⁺荧光粉的物相、形貌和荧光性质。在紫外光激发下,CGTO： xTb³⁺荧光粉实现了较强的绿光发射,绿光为Tb³⁺离子的⁵D₄-⁷F₅跃迁。通过变温发射光谱研究发现CGTO：0.15Tb³⁺荧光粉的热猝灭活化能为0.181 9 eV。在255 nm的激发下,最佳Tb³⁺掺杂浓度的CGTO：0.15Tb³⁺荧光粉的量子效率为32.32%。     

一步水热合成Cu-SAPO-34选择性催化丙烯还原氮氧化物

采用一步法水热合成不同Cu/Al比的Cu-SAPO-34催化剂,并对其丙烯选择性催化还原NO（C₃H₆-SCR）性能进行了研究。通过N₂吸附-脱附、X射线衍射（XRD）、X射线光电子能谱（XPS）、程序升温还原（H₂-TPR）和原位漫反射傅里叶变换红外光谱（In situ DRIFTS）等研究手段对催化剂进行表征,考察Cu-SAPO-34中Cu物种含量对催化剂的物理化学性质和反应活性的影响。结果表明,当铜负载量为2.76%~4.12%（w/w）时,Cu-SAPO-34催化剂在富氧条件下300~400℃内表现出非常有吸引力的C₃H₆-SCR活性,可实现~100%的脱硝效率和~100%的N₂选择性。原位红外光谱研究表明,Cu-SAPO-34分子筛骨架上孤立的Cu²⁺离子是NO吸附和活化形成NO₂^-/NO₃^-中间物种的主要活性位,并通过C₃H₆-SCR反应过程中Cu²⁺/Cu⁺氧化还原循环来实现Cu²⁺离子的持续供给。     

电荷补偿对Ba2ZnGe2O7：Bi3+荧光粉发光性质的影响

采用高温固相法制备了2个系列的荧光粉样品：Ba_2-xZnGe₂O₇：xBi³⁺（系列Ⅰ）和Ba_1.994-yK_yZnGe₂O₇：0.006Bi³⁺（系列Ⅱ）。X射线衍射（XRD）测试结果表明,少量Bi³⁺、K⁺的掺杂不会明显改变材料的物相结构。样品的荧光光谱测试结果表明,虽然2个系列样品的发光光谱都随组成成分变化有少量变化,但发光颜色基本上均为黄绿色。在358 nm的激发下,荧光粉的发射光谱呈现一个峰值在500 nm的宽发射带,归属于³P₁→¹S₀能级跃迁。在500 nm监测下,荧光粉的最强激发峰位于358 nm,归属于¹S₀→³P₁能级跃迁,此外还有一个位于320 nm的肩峰归属于O^2--Bi³⁺电荷转移带。系列Ⅰ样品的光谱数据结果指出,Bi³⁺的最佳掺杂量x为0.006。在该基质中,Bi³⁺掺杂取代Ba²⁺属于不等价取代,会在晶格中产生Ba²⁺空位或间隙O^2-,对材料的发光强度产生负面影响。对此,采用K⁺与Bi³⁺协同掺杂起到电荷补偿的作用,填补Ba²⁺空位或捕获间隙O^2-缺陷。空位被填补或间隙被捕获均减少了晶格畸变,从而使发光强度明显提高。系列Ⅱ样品的光谱数据表明,完全电荷补偿的荧光粉样品相比于没有掺K⁺的样品,其发光强度提高了约2.5倍。     

水热合成LuF3:Yb3+,Er3+微晶及其上转换发射与温度传感特性

通过在不同pH值下的简易水热法合成不同Yb³⁺离子（n_YB³⁺/n_Lu³⁺=5%~15%）和Er³⁺离子（n_Er³⁺/n_Lu³⁺=1%~5%）掺杂浓度的LuF₃∶Yb³⁺,Er³⁺微晶荧光粉。发现pH值对正交相LuF₃∶Yb³⁺,Er³⁺的合成起着关键作用。在980 nm激发下,LuF₃∶Yb³⁺,Er³⁺荧光体呈现出以523 nm（²H_11/2→⁴I_15/2）和539 nm（⁴S_3/2→⁴I_15/2）为中心的强绿光上转换（UC）发射以及以660 nm（⁴F_9/2→⁴I_15/2）为中心弱红光上转换发射。通过使用X射线衍射（XRD）和光致发光（PL）分析测定了最强发射强度的Er³⁺和Yb³⁺的最佳掺杂浓度。浓度依赖性研究表明,达到最强的绿光上转换发光时最佳掺杂浓度为10% Yb³⁺,2% Er³⁺。通过改变泵浦功率来研究LuF₃∶Yb³⁺,Er³⁺荧光粉UC发光机制。通过980 nm二极管激光器在293~573 K的范围内研究了在523和539 nm处的2个绿光UC发射带的荧光强度比（FIR）的温度依赖性,发现在490 K得到最大灵敏度约为15.3×10^-4 K^-1。这表明LuF₃∶Yb³⁺,Er³⁺荧光体可应用于具有高灵敏度的光学温度传感器。     

Tm3+/Er3+/Ho3+共掺SiO2-Bi2O3-AlF3-BaF2玻璃发光性能

采用高温熔融法制备了Tm³⁺/Er³⁺/Ho³⁺共掺的铋硅酸盐50SiO₂-40Bi₂O₃-5AlF₃-5BaF₂玻璃。研究了在808 nm激光器（Laser Diode）激发下Tm³⁺/Er³⁺/Ho³⁺共掺的铋硅酸盐在2 060 nm处的发光性能,同时测试及分析了该铋硅酸盐玻璃的差热特性、吸收光谱及荧光光谱。根据吸收光谱以及Judd-Oflet理论,计算了Ho³⁺的Judd-Oflet强度参数Ω_t（t=2,4,6）以及Tm³⁺/Er³⁺/Ho³⁺相应的吸收截面。铋硅酸盐玻璃中,Tm₂O₃、Er₂O₃和Ho2O3掺杂浓度分别为0.75%、1.0%和0.5%时,2 060 nm处Ho³⁺∶⁵I₇→⁵I₈发射峰强度达到最大。对Tm³⁺/Er³⁺/Ho³⁺ 3种离子的光谱性质和离子间可能存在的能量传递也做了分析。Ho³⁺在1 953 nm处的最大吸收截面σ_abs为9.08×10^-21 cm²,在2 060 nm处的最大发射截面σem为11.68×10^-21 cm²,辐射寿命τ_mea为2.75 ms,具有良好的增益效应σ_emτ（3.212×10^-20 cm^-2·ms）。     

白光LED用Sr0.955Al2Si2-xTixO8：Eu2+荧光粉的晶体结构和光谱特性

由高温固相反应制得Sr_0.955Al₂Si_2-xTi_xO₈：Eu²⁺（x=0~1.0）系列试样,研究了Ti⁴⁺置换Si⁴⁺对其晶体结构和光谱特性的影响。Ti⁴⁺以类质同相替代Si⁴⁺进入晶体晶格中,形成了连续固溶体,其晶胞参数a,b,c,β和晶胞体积V随Ti⁴⁺置换量呈线性递增。Ti⁴⁺置换Si⁴⁺对晶胞参数c的影响显著,b其次,a最小。荧光激发谱为宽带,位于230~400nm,由267nm、305nm、350nm和375nm 4个峰拟合成,表观峰值位于351nm;随着Ti⁴⁺置换量的增加,半高宽（FWHM）从105nm减小到93nm。发射光谱位于380~600nm,表观峰值位于407nm,可由406nm和441nm两峰拟合而成并且随Ti⁴⁺置换量增加线性红移,Ti⁴⁺进入晶格对长波长发射中心影响较少;Ti⁴⁺置换量为1.0时,表观发射峰位从407nm红移至417nm;利用试样荧光光谱和VanUitert经验公式,得出SrAl₂Si₂O₈：Eu²⁺中Sr²⁺的配位数为9。随着Ti⁴⁺置换量Si⁴⁺进入基质晶格,造成Eu-O距离变小,使得Eu²⁺所处的晶体场强度增强,发光中心Eu²⁺的5d能级分裂增大,造成Eu²⁺最低发射能级重心下移,两拟合谱峰峰位均呈线性红移。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.