基于ZnO溶胶-凝胶固定的酪氨酸酶传感器的研制

通过使用带正电荷的ZnO溶胶-凝胶在玻碳电极表面固定酶,研制了一种简单有效的酪氨酸酶传感器。结果表明,ZnO溶胶-凝胶的等电点为酪氨酸酶的固定提供了有利的微环境,酪氨酸酶能很好地保持其生物活性。所研制的传感器达到95%稳定状态电流的时间在10 s以内。酚类化合物可通过酶催化产生的醌在-200 mV(对饱和甘汞电极)直接还原而测定,传感器对苯酚测定的灵敏度为168μA.mmol-1.L-1,线性范围为1.5×10-7~4.0×10-5mol.L-1,检出限为8.0×10-8mol.L-1。该传感器使用二周后活性仍保持原有活性的75%。     

基于蛋白A/纳米金/壳聚糖分散的多壁碳纳米管修饰的电位型甲胎蛋白免疫传感器的研究

将壳聚糖分散的多壁碳纳米管(MWNT-CS)滴涂于金电极(Au)表面,利用壳聚糖大量的氨基将纳米金(nano-Au)固定到金电极表面,再利用蛋白A(PA)的定向固定效应将甲胎蛋白抗体(anti-AFP)固定到纳米金修饰的金电极表面,从而制得高灵敏、高稳定电位型甲胎蛋白免疫传感器。蛋白A为抗原和抗体的反应提供了合理的基础,纳米金的存在提高了抗体在电极表面的固定量,多壁碳纳米管(MWNT)促进了电子的传递,从而缩短电极的响应时间。在优化的实验条件下,该传感器响应的电极电位与甲胎蛋白浓度的对数在7.0~190.0μg/L的范围内保持良好的线性关系,检出限(S/N=3)为3.9μg/L。     

壳聚糖-纳米金-葡萄糖氧化酶生物传感器的制备及其应用于葡萄糖的测定

采用了一种简便快捷的电沉积方法制备了壳聚糖-纳米金复合膜并应用于葡萄糖生物传感器的构建.氯金酸和壳聚糖的混合液在玻碳电极表面电化学还原为金纳米粒子,再将葡萄糖氧化酶通过戊二醛交联的方式固定在纳米金复合膜修饰的玻碳电极表面,制成一种新型的葡萄糖氧化酶生物传感器.该传感器对葡萄糖的响应十分快速,在5 S内即达到平衡.测定葡萄糖的线性范围为20μmol·L-1～5 mmol·L-1,检出限(3S/N)为12μmol·L-1.     

Tyr/Glu/Fe_3O_4/Nafion/CNT/GCE酪氨酸酶生物传感器的制备及应用于农药检测的研究

制备了磁性四氧化三铁纳米粒子,采用碳纳米管、Nafion等功能性材料构建了酪氨酸酶(Tyr)生物传感器,并将其应用于农药的检测.实验表明,四氧化三铁纳米粒子具有良好的生物兼容性,碳纳米管能够有效地促进电子传递,修饰了四氧化三铁纳米粒子等功能性材料的酶传感器,响应速度快,检测灵敏度高,稳定性好;固定在传感器上的酪氨酸酶有良好的酶动力学响应,其表观米氏常数为61.5μmol/L.利用农药对酪氨酸酶的抑制作用,以苯酚为底物,对农药呋喃丹进行了检测,检测限达到2.0×10-9mol/L.     

无试剂金胶-半胱胺苯酚传感器研究

用电化学方法研究了金胶表面固定酪氨酸酶(Tyr)的直接电子传递行为和该修饰电极在苯酚分析方面的应用。金胶联接在半胱胺自组装单层尾部的氨基上。在pH7.0的0.1 mol/L磷酸盐缓冲溶液中,Tyr/金胶/半胱胺修饰电极上的Tyr进行直接电子传递,产生一对氧化还原峰。固定在金胶表面的Tyr的表面覆盖度为6.6×10-10mol/cm2。不需要电子媒介体的作用,该传感器对苯酚的还原具有较好的电催化作用。苯酚测定的线性范围为2.5μmol/L~5 mmol/L,检出限为0.8μmol/L(信噪比是3)。该传感器对苯酚的测定显示了良好的重复性。在高浓度的苯酚中,此传感器表现出Michaelis-Menten行为,KMapp为3.8 mmol/L。     

基于Nafion-氧化石墨烯复合物/硫堇/纳米金构建过氧化氢传感器的研究

利用Nafion(全氟聚苯乙烯磺酸溶液)-氧化石墨烯复合物、硫堇和纳米金构建了H2O2酶传感器。首先将氧化石墨烯分散在体积分数0.2%Nafion溶液中制得Nafion-氧化石墨烯的复合物,并将其固定在玻碳电极表面,通过静电吸附将带正电荷的硫堇吸附到Nafion-氧化石墨烯复合膜修饰的玻碳电极表面,再利用静电吸附将纳米金修饰于电极上,通过纳米金来固定辣根过氧化物酶从而制得H2O2传感器。用循环伏安法和计时电流法考察该修饰电极的电化学特性。H2O2浓度为5.5×10-6~1.0×10-3mol/L时,酶电极的响应电流值与H2O2的浓度呈良好的线性关系,检出限为1.80×10-6mol/L。     

基于纳米金/硫堇层层自组装的新型电流型酶-癌胚抗原免疫传感器

将Nafion 膜固定在金电极(Au)表面, 通过静电吸附和共价键合作用将硫堇(Thi)和纳米金颗粒(nano-Au)层层自组装到Nafion膜修饰的金电极表面. 再通过形成的纳米金单层吸附癌胚抗体(anti-CEA), 最后用辣根过氧化物酶(HRP)代替牛血清白蛋白(BSA)封闭电极上的非特异性吸附位点, 并同时起到放大响应电流信号的作用, 从而制得高灵敏、高稳定电流型酶-癌胚抗原(CEA)免疫传感器. 通过循环伏安和交流阻抗考察了电极表面的电化学特性, 并对该免疫传感器的性能进行了详细的研究. 该传感器对CEA检测的线性范围为2.5~80.0 ng/mL, 检测限为0.90 ng/mL.     

基于纳米金与碳纳米管-纳米铂-壳聚糖纳米复合物固定癌胚抗原免疫传感器的研究

采用纳米金(nano-Au)、多壁碳纳米管-纳米铂-壳聚糖的纳米复合物(MWNT-Pt-CS)及电子媒介体硫堇(Th)固载抗体制得高灵敏癌胚抗原免疫传感器．首先, 于壳聚糖溶液中用NaBH4还原H2PtCl6, 并将多壁碳纳米管分散于其中制得碳纳米管-纳米铂-壳聚糖纳米复合物, 并将其滴涂在玻碳电极上成膜; 然后, 吸附电子媒介体硫堇制得硫堇/碳纳米管-纳米铂-壳聚糖(Th/MWNT-Pt-CS)修饰电极．利用壳聚糖和硫堇分子中大量的氨基固定纳米金并吸附癌胚抗体(anti-CEA); 最后, 用辣根过氧化物酶(HRP)封闭活性位点从而制得高灵敏电流型免疫传感器．在优化的实验条件下, 该传感器响应的峰电流值与癌胚抗原(carcinoembryonic antigen)浓度在0.5～10和10～120 ng/mL的范围内保持良好的线性关系, 检测限为0.2 ng/mL．     

基于仿生聚多巴胺膜和纳米金的酶固定化平台的构建

首次以仿生聚多巴胺膜为功能基底膜并结合使用纳米金, 构建了一种高导电性、稳健的酶生物分子固定化平台. 以固定辣根过氧化物酶(HRP)为例, 发展了一种新的电化学酶传感器用于H2O2的测定. 结果表明, 酶传感器借助聚多巴胺膜对基底电极的高结合力及其高生物亲和性与电活性, 并协同纳米金的“电子通道”作用, 不仅可以实现酶分子在电极表面的大量而高活性的固定化, 而且能促进电子在酶活性中心和电极表面间的快速传递. 与采用其它常见聚合物材料(例如壳聚糖)的酶传感器比较, 以聚多巴胺/纳米金固定化平台发展的酶传感器具有更优良的检测H2O2的性能. 其对H2O2的检测线性范围为4.0×10－7～4.5×10－4 mol•L－1, 检测限为3.7×10－7 mol•L－1, 灵敏度为100.2 μA•L•mmol－1. 此外, 该酶传感器还具有优良的检测重现性和存贮稳定性, 以及较好的抗干扰能力.     

纳米聚苯胺修饰石墨电极的葡萄糖双酶传感器

用循环伏安法在石墨电极上制得纳米纤维聚苯胺, 并在其上固定葡萄糖氧化酶(GOD)和辣根过氧化物酶(HRP)制备葡萄糖双酶传感器. 用交流阻抗、SEM等技术对其进行表征; 考察了各种因素对双酶电极响应电流的影响以及双酶电极的稳定性. 该传感器对葡萄糖响应电流的测定在0.05 V(vs SCE)下进行, 有效避免了电活性物质的影响, 线性响应范围为0.05-2.0 mmol·L-1.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.