均布载荷作用下具有光滑中心波纹膜片的非线性分析

采用轴对称旋转壳体的简化Reissner方程，研究了在均布载荷作用下具有光滑中心波纹膜片的非线性弯曲问题。应用格林函数方法，波纹膜片的非线性边值问题化为了非线性积分方程的求解。为了求解积分方程并防止发散，一个插值参数被引入到迭代格式中。计算表明，当载荷很小时，任何插值参数值均能保证迭代的收敛性，取插值参数值接近或等于1获得较快的收敛速度，而当载荷较大时，插值参数值不能取得过大。绘出了波纹膜片的特征曲线，得到的特征曲线可供设计参考。可以断言，当载荷不大时，特征曲线是近似线性的，随着载荷的增大，特征曲线开始向上弯曲，明显偏离线性。本文中提出的解决方法适应于任意轴向截面的波纹壳体。     

均布载荷作用下带边缘大波纹膜片的非线性弯曲

采用轴对称旋转壳体的简化Reissner方程，研究了在均布载荷作用下具有硬中心的带边缘大波纹膜片的非线性弯曲问题．应用积分方程方法，获得了具有夹紧固定和滑动固定两种外边界的膜片的特征关系，即荷载-中心挠度曲线．作为算例，给出了夹紧固定膜片中的应力分布．     

METHOD OF GREEN＇S FUNCTION OF CORRUGATED SHELLS

By using the fundamental equations of axisymmetric shallow shells of revolution, the nonlinear bending of a shallow corrugated shell with taper under arbitrary load has been investigated. The nonlinear boundary value problem of the corrugated shell was reduced to the nonlinear integral equations by using the method of Green＇s function. To solve the integral equations, expansion method was used to obtain Green＇s function. Then the integral equations were reduced to the form with degenerate core by expanding Green＇s function as series of characteristic function. Therefore, the integral equations become nonlinear algebraic equations. Newton＇ s iterative method was utilized to solve the nonlinear algebraic equations. To guarantee the convergence of the iterative method, deflection at center was taken as control parameter. Corresponding loads were obtained by increasing deflection one by one. As a numerical example,elastic characteristic of shallow corrugated shells with spherical taper was studied.Calculation results show that characteristic of corrugated shells changes remarkably. The snapping instability which is analogous to shallow spherical shells occurs with increasing load if the taper is relatively large. The solution is close to the experimental results.     

集中载荷作用下具有光滑中心波纹膜片的非线性分析

波纹膜片是一种薄壳弹性体，由于它的参数很多，又相互制约，所以使得它的设计很复杂。在大多数位移式仪器仪表中，要求波纹膜片产生至少和膜片厚度是同样数量级的弹性位移。这就要求使用薄壳的几何非线性理论进行分析。大多数学者研究波纹膜片的弯曲问题，是采用扁壳理论讨论具有浅波纹的膜片。而工程实际中，经常遇到深波纹膜片，这就要求从一般壳体大挠度方程进行求解。本文采用轴对称旋转壳体的简化Re-issner方程。研究了在中心集中载荷作用下具有光滑中心波纹膜片的非线性弯曲问题。应用积分方程方法，可以获得膜片的特征关系（载荷-中心挠度关系）和应力分布。文末给出实例计算的数值结果。     

复合载荷作用下具有光滑中心波纹膜片的非线性分析

采用轴对称旋转壳体的简化Reissner方程，研究了在复合载荷作用下具有光滑中心波纹膜片的非线性弯曲问题。应用积分方程方法，可以获得膜片的特征关系（载荷－中心挠度关系）。文末给出了实例计算的数值结果。     

Nonlinear vibration of corrugated shallow shells under uniform load

Based on the large deflection dynamic equations of axisymmetric shallow shells of revolution, the nonlinear forced vibration of a corrugated shallow shell under uniform load is investigated. The nonlinear partial differential equations of shallow shell are reduced to the nonlinear integral-differential equations by the method of Green's function. To solve the integral-differential equations, expansion method is used to obtain Green's function. Then the integral-differential equations are reduced to the form with degenerate core by expanding Green's function as series of characteristic function. Therefore, the integral-differential equations become nonlinear ordinary differential equations with regard to time. The amplitude-frequency response under harmonic force is obtained by considering single mode vibration. As a numerical example, forced vibration phenomena of shallow spherical shells with sinusoidal corrugation are studied. The obtained solutions are available for reference to design of corrugated shells     

波纹壳的摄动解法

应用扁锥壳的非线性大挠度理论,研究了在均布载荷和中心集中载荷下,具有光滑中心的锯齿形和梯形波纹壳,采用摄动法和幂级数方法,得到了波纹壳的弹性特征。本文的解答符合实验结果。     

Nonlinear natural frequency of shallow conical shells with variable thickness

IntroductionTheplatesandtheshellswithvariablethicknessarewidelyusedinengineering .Theproblemaboutstaticshasbeenstudiedbymanyscholars;therearemanyRefs .[1 -4 ]inthisfield .Papersaboutnonlineardynamicsaremuchless[5 ,6 ].Inthispaper,selectingthemaximumamplitudeinthecenterofshallowconicalshellswithvariablethicknessasperturbationparameter,thenonlinearnaturalfrequencyofshallowconicalshellswithvariablethicknessisobtainedbymethodgiveninRef.[7] .Thenonlinearnaturalfrequencyisnotonlyconnectedwiththeva…     

柱面扁壳的非线性数值分析

本文研究了柱面扁壳在均布荷载作用下的大变形弯曲问题。首先导出了位移型非线性控制微分方程,然后结合两种边界情况(简支与固定)给出了用正交配点法进行解算的详细公式。     

任意变厚度的旋转扁薄壳非线性稳定的幂函数解法

以幂函数为试函数,两次使用配点法成功地分离了耦合的大挠度方程,从而导出变厚度旋转扁壳非线性稳定的计算式。支座可以是弹性的。本文给出了均布或多项式分布荷载作用下,线性或多项式型变厚度的圆锥壳、球壳、余弦壳或四次多项式型旋转壳的上、下临界荷载。均布荷载作用下指数型变厚度球壳的上临界荷载同其他方法的结果作了比较。用配点法编写的程序具有收敛范围大、精度高、通用性强和计算时间少的优点。     

Stability of Orthotropic Corrugated Cylindrical Shells

A technique for stability analysis of cylindrical shells with a corrugated midsurface is proposed. The wave crests are directed along the generatrix. The relations of shell theory include terms of higher order of smallness than those in the Mushtari–Donnell–Vlasov theory. The problem is solved using a variational equation. The Lamé parameter and curvature radius are variable and approximated by a discrete Fourier transform. The critical load and buckling mode are determined in solving an infinite system of equations for the coefficients of expansion of the resolving functions into trigonometric series. The solution accuracy increases owing to the presence of an aggregate of independent subsystems. Singularities in the buckling modes of corrugated shells corresponding to the minimum critical loads are determined. The basic, practically important conclusion is that both isotropic and orthotropic shells with sinusoidal corrugation are efficient only when their length, which depends on the waveformation parameters and the geometric and mechanical characteristics, is small     

Unsymmetrical nonlinear bending problem of circular thin plate with variable thickness

Introduction Manystructuralelements(pole,plate,shell)withunevenandvariablethicknessarewidely usedinallkindsofengineeringfields.Engineerscansavematerialswhentheydesignbecause theseelementshavebetteroptimizedshapeofstructuralfeature,butthisaddsdifficultytotheanalysisoftheirmechanicalcapability.Manypreviouspapers[1-4]havesolvedtheproblemof symmetricalaxis,butnobodyhassolvedtheunsymmetricalnonlineardeformationproblemof circularthinplatewithvariablethicknessandunsymmetricalaxisuptonow,afewworkonly …     

半圆环截面细环壳的屈曲

本文由Sanders非线性平衡方程和Koiter小应变协调方程推导出细环壳的非线性微分方程和稳定方程。用伽辽金法求解了静水压或边界载荷作用下的半园环截面细环壳的稳定方程。对于不同的边界条件及一系列几何参数,计算得到了临界载荷及屈曲模态。     

S型功能梯度扁球壳非线性屈曲的渐近分析

本文利用渐近迭代法获得了边界弹性支撑的功能梯度扁球壳的非线性屈曲问题的理论解．假设材料组分体积分数沿壳体厚度方向呈sigmoid幂函数变化,边界上考虑一般的弹性支撑约束．基于经典的薄壳理论和几何非线性关系,导出了S型功能梯度扁球壳的非线性屈曲问题的控制方程．采用渐近迭代法通过两次迭代得到了无量纲挠度和均布荷载之间的非线性特征关系．通过与已有有限元方法和其他数值方法的结果对比,验证了本文解的有效性和高精度．同时,通过计算阐述了缺陷因子、材料参数、边界约束系数及特征几何参数对壳体临界屈曲荷载的影响．     

Uniform Convergence Series to Solve Nonlinear Partial Differential Equations: Application to Beam Dynamics

Extended trigonometric series of uniform convergence are proposed as a method to solve the nonlinear dynamic problemsgoverned by partial differential equations. In particular, the method isapplied to the solution of a uniform beam supported at its ends withnonlinear rotational springs and subjected to dynamic loads. The beam isassumed to be both material and geometrically linear and the end springs are of the Duffing type. The action may be a continuous load q = q(x, t) within a certain range and/or concentrated dynamic moments at the boundaries. The adopted solution satisfies the differential equation, the initial conditions, andthe nonlinear boundary conditions. It has been previously demonstrated that, due to the uniform convergence of the series, the method yieldsarbitrary precision results. An illustration example shows theefficiency of the method.     

Timoshenko-Type Theory in the Stability Analysis of Corrugated Cylindrical Shells

A technique is proposed for stability analysis of longitudinally corrugated shells under axial compression. The technique employs the equations of the Timoshenko-type nonlinear theory of shells. The geometrical parameters of shells are specified on discrete set of points and are approximated by segments of Fourier series. Infinite systems of homogeneous algebraic equations are derived from a variational equation written in displacements to determine the critical loads and buckling modes. Specific types of corrugated isotropic metal and fiberglass shells are considered. The calculated results are compared with those obtained within the framework of the classical theory of shells. It is shown that the Timoshenko-type theory extends significantly the possibility of exact allowance for the geometrical parameters and material properties of corrugated shells compared with Kirchhoff–Love theory.     

均布压力作用下悬链线波纹壳应力和位移的初参数积分方程分析

本文用初参数积分方程方法，对悬链线波纹壳在均布压力作用下的应力和位移进行了分析，并给出了一个算例。     

功能梯度截顶圆锥壳的热弹性弯曲精确解

研究了功能梯度材料截顶圆锥壳在横向机械载荷与非均匀热载荷同时作用下的变形问题. 基于经典线性壳体理论推导出了以横向剪力和中面转角为基本未知量的功能梯度薄圆锥壳轴对称变形的混合型控制方程. 假设功能梯度圆锥壳的材料性质为沿厚度方向按照幂函数连续变化的形式. 然后采用解析方法求解,得到了问题的精确解. 分别就两端简支和两端固支边界条件,给出了圆锥壳的变形随其载荷、材料参数等变化的特征关系曲线,重点分析和讨论了载荷参数与材料梯度变化参数对变形的影响.      

Theoretical analysis on elastic buckling of nanobeams based on stress-driven nonlocal integral model

Several studies indicate that Eringen's nonlocal model may lead to some inconsistencies for both Euler-Bernoulli and Timoshenko beams, such as cantilever beams subjected to an end point force and fixed-fixed beams subjected a uniform distributed load. In this paper, the elastic buckling behavior of nanobeams, including both EulerBernoulli and Timoshenko beams, is investigated on the basis of a stress-driven nonlocal integral model. The constitutive equations are the Fredholm-type integral equations of the first kind, which can be transformed to the Volterra integral equations of the first kind. With the application of the Laplace transformation, the general solutions of the deflections and bending moments for the Euler-Bernoulli and Timoshenko beams as well as the rotation and shear force for the Timoshenko beams are obtained explicitly with several unknown constants. Considering the boundary conditions and extra constitutive constraints, the characteristic equations are obtained explicitly for the Euler-Bernoulli and Timoshenko beams under different boundary conditions, from which one can determine the critical buckling loads of nanobeams. The effects of the nonlocal parameters and buckling order on the buckling loads of nanobeams are studied numerically, and a consistent toughening effect is obtained.     

Elastic nonlinear stability analysis of thin rectangular plates through a semi-analytical approach

A semi-analytical approach to the elastic nonlinear stability analysis of rectangular plates is developed. Arbitrary boundary conditions and general out-of-plane and in-plane loads are considered. The geometrically nonlinear formulation for the elastic rectangular plate is derived using the thin plate theory with the nonlinear von Kármán strains and the variational multi-term extended Kantorovich method. Emphasis is placed on the effect of destabilizing loads and on the derivation of the solution methodologies required for tracking a highly nonlinear equilibrium path, namely: parameter continuation and arc-length continuation procedures. These procedures, which are commonly used for the solution of discretized structural systems governed by nonlinear algebraic equations, are augmented and generalized for the direct application to the PDE. The boundary value problem that results from the arc-length continuation scheme and consists of coupled differential, integral, and algebraic equations is re-formulated in a form that allows the use of standard numerical BVP solvers. The performance of the continuation procedures and the convergence of the multi-term extended Kantorovich method are examined through the solution of the two-dimensional Bratu–Gelfand benchmark problem. The applicability of the proposed approach to the tracking of the nonlinear equilibrium path in the post-buckling range is demonstrated through numerical examples of rectangular plates with various boundary conditions.