Tire tread pattern design trigger on the stress distribution over rigid surfaces and soil compaction

Studies comparing the structural differences of tires have not qualitatively or quantitatively considered the effects of tread geometry on tire behaviour or the interactions of the tire with the surface. Therefore, to determine the effects of different tire tread patterns on the stress distribution of the tire and soil compaction, we compared the structural behaviours of a high-flotation tractive-tread (TT) tire and a smooth-tread (ST) tire. The experiments were conducted over a rigid and over a deformable surface. The results from the rigid surface shows the influences of the tread pattern and sidewalls is dependent of the loads. Over the deformable surface, the contact area of the TT tire was larger than that of the ST tire. The inflation pressure (IP) was mainly responsible for the load support before the soil reached its maximum deformation. Next, the tread and sidewalls exhibited the same behaviour as observed on the rigid surface. In addition, we observed alterations in the balloon point with the tread geometry and the type of surface due to changes in the contact pressure. With carcass deformation, the volume of the tire was visibly reduced, which indicated that the IP could increase.     

Development and validation of off-road tire-gravelly soil interaction using advanced computational techniques

This paper presents a novel modelling technique to compute the interaction between an 8x4 off-road truck and gravelly soil (sand with gravel soil). The off-road truck tire size 315/80R22.5 is modelled using the Finite Element Analysis (FEA) technique and validated using manufacturer-provided data in static and dynamic responses. The gravelly soil is modelled using Smoothed-Particle Hydrodynamics (SPH) technique and calibrated against physical measurements using pressure-sinkage and direct shear-strength tests. The tire-gravelly soil interaction is captured using the node symmetric node to segment with edge treatment algorithm deployed for interaction between FEA and SPH elements. The model setup consists of four tires presenting the four axles of the truck, the first tire is a free-rolling steering tire, the second and third tires are driven tires and the fourth tire is a free-rolling push tire. The truck tires-gravelly soil interaction is computed and validated against physical measurements performed in Göteborg, Sweden. The effect of gravelly soil compaction and truck loading on the tire performance is discussed and investigated.     

Tire inflation and its influence on drawbar characteristics and performance – Energetic indicators of a tractor set

This work deals with the influence of tire inflation on tractive characteristics and performance-energetic parameters of a ploughing set. The test was conducted using two tire sets with different tire pressures under field conditions. Measurements of tractive properties were performed by setting travel speeds to 5, 8, and 10 kph, respectively. The ploughing set was operated at 8 kph, according to the manufacturer’s recommendation. The measurement results were processed graphically and mathematically into the Vehicle Traction Ratio, drawbar power, and slip characteristics. The tire inflation, reduced from 180 to 65 kPa and/or 75 kPa, of tires with wide treads (low-profile) resulted in increase of the front tire footprint by 24.7% and rear tire footprint by 31.1%. This change had a positive impact on the specific tractive fuel consumption that decreased in the range from 3.4% to 16.0%, depending on the travel speed. The results of performed measurements revealed that reducing the tire inflation of appropriate tires can improve the drawbar characteristics and consequently the fuel consumption.     

Thermo-mechanically coupled investigation of steady state rolling tires by numerical simulation and experiment

In this contribution, a numerical framework for the efficient thermo-mechanical analysis of fully 3D tire structures (axisymmetric geometry) in steady state motion is presented. The modular simulation approach consists of a sequentially coupled mechanical and thermal simulation module. In the mechanical module, the Arbitrary Lagrangian Eulerian (ALE) framework is used together with a 3D finite element model of the tire structure to represent its temperature-dependent viscoelastic behavior at steady state rolling and finite deformations. Physically computed heat source terms (energy dissipation from the material and friction in the tire–road contact zone) are used as input quantities for the thermal module. In the thermal module, a representative cross-sectional part of the tire is employed to evaluate the temperature evolution due to internal and external heat sources in a transient thermal simulation. Special emphasis is given to an adequate material test program to identify the model parameters. The parameter identification is discussed in detail. Numerical results for three different types of special performance tires at free rolling conditions are compared to experimental measurements from the test rig, focusing especially on rolling resistance and surface temperature distribution.     

ANALYSIS OF GROUNDING CHARACTERISTICS AND STRAIN ENERGY OF RADIAL TIRES WITH RADIAL STIFFNESS1)

利用轮胎综合试验机对径向刚度下子午线轮胎进行性能试验,采用正交试验法针对不同胎压、垂向载荷下轮胎的接地特性进行分析,结合仿真软件ABAQUS与试验进行对比。结果表明,橡胶材料Mooney-Rivli模型也具有一定的适用性,胎压增大时径向刚度发生线性变化,胎面印痕由椭圆形转变成近似矩形,印痕面积略微增大;随着胎压的不断增大,胎面印痕的面积显著减小,接触面的压力主要集中在胎肩,胎冠处也有所增加;胎压一定时,垂向载荷逐渐增大时,整个印痕面的应力呈对称分布,印痕面应力由内高外低逐渐向外高内低变化。建立数学模型与有限元软件同时对轮胎进行应变能分析,发现在低胎压150 kPa下受载荷时轮胎容易发生微小侧向位移同时发生变形,此时极易引起迟滞损失并造成应变能急剧增加。     

Thrust and slip of a low-pressure tire on compressible ground by the compression-sliding approach

Driving wheels with low-pressure lugged tires are standard propulsion components of wheeled off-road vehicles. Such wheels have been mostly treated in theory as shorter tracks or even as “black boxes”. These procedures, however, appear not to be necessary since an updated theory of thrust generation, based on experiments with double-plate meter, was presented at the 2008 ISTVS Turin conference. This theory is based on the compaction-sliding (CS) concept, which claims that the rearward displacement of soil, a reason for slip, starts as horizontal soil compression by lugs (C-stage at lower thrust), followed by the slide of sheared off soil blocks (S-stage at higher thrust). The thrust in terms of ISTVS Standards equals gross tractive effort minus internal rolling resistance of a tire. The resultant thrust of a tire equals the sum of component thrusts of individual soil segments. The respective technique provides thrust-slip curves, which reflect tire size, loading, inflation pressure and tread pattern design, e.g. tread density, lug angle, pitch, height and tire casing lay-out and thus can be useful notably in assessing the traction properties of new tire designs. Concerning the evaluation of tire traction tests or similar applications, the CS approach offers a simplified version of thrust-slip formula (G-function), which complies with the CS concept and is easy to use.     

基于实验的数值反演的滚动轮胎稳态温度场的有限元分析

根据轮胎温度场的单向解耦分析思想,形成了一个基于ABAQUS程序的轮胎稳态温度场的分析方法,单向解耦过程分为变形、损耗、热传导三个分析过程。变形分析中,采用了平衡态的超弹性材料模型;损耗分析中,依据变形分析获得的应力应变场,结合材料粘性损耗特性来获得损耗能量;热传导分析中,依据实测的轮胎胎侧温度场,提出了一种基于实验的数值反演方法来确定胎侧的对流热边界条件。由于轮胎胎侧的形状和结构细节,其对流热边界不同于旋转平圆盘的对流热边界,本文的数值反演方法避免了实测胎侧对流热交换系数的困难。     

Soil compaction and tires for harvesting and transporting sugarcane

Four tire types (A, block-shape tread; B, rib-shape tread; C, low-lug tread; D, high-lug tread) used to harvest and transport sugarcane were compared regarding the compaction induced to the soil. Tires were tested at three inflation pressures (207, 276, 345 kPa) and six loads ranging from 20 to 60 kN/tire. Track impressions were traced, and 576 areas were measured to find equations relating inflation pressure, load, contact surface and pressure. Contact surface increased with increasing load and decreasing inflation pressure; however, the contact pressure presented no defined pattern of variation, with tire types A and B generating lower contact pressure. The vertical stresses under the tires were measured and simulated with sensors and software developed at the Colombian Sugarcane Research Center (Cenicaña). Sensors were placed at 10, 30, 50 and 70 cm depth. Tire types A and B registered vertical stresses below 250 kPa at the surface. These two tires were better options to reduce soil compaction. The equations characterizing the tires were introduced into a program to simulate the vertical stress. Simulated and measured stresses were adjusted in an 87–92% range. Results indicate a good correlation between the tire equations, the vertical stress simulation and the vertical stress measurement.     

Effects of tire inflation pressure and tractor velocity on dynamic wheel load and rear axle vibrations

The objective of this study was to evaluate the effects of agricultural tire characteristics on variations of wheel load and vibrations transmitted from the ground to the tractor rear axle. The experiments were conducted on an asphalt road and a sandy loam field using a two-wheel-drive self-propelled farm tractor at different combinations of tractor forward speeds of approximately 0.6, 1.6 and 2.6 m/s, and tire inflation pressures of 330 and 80 kPa. During experiments, the vertical wheel load of the left and right rear wheels, and the roll, bounce and pitch accelerations of the rear axle center were measured using strain-gage-based transducers and a triaxial accelerometer. The wavelet and Fourier analyses were applied to measured data in order to investigate the effects of self-excitations due to non-uniformity and lugs of tires on the wheel-load fluctuation and rear axle vibrations. Values for the root-mean-square (RMS) wheel loads and accelerations were not strictly proportional and inversely proportional to the forward speed and tire pressure respectively. The time histories and frequency compositions of synthesized data have shown that tire non-uniformity and tire lugs significantly excited the wheel load and accelerations at their natural frequencies and harmonics. These effects were strongly affected by the forward speed, tire pressure and ground deformation.     

Tire and soil effects on power loss: Measurement and comparison with finite element model results

In the present study, the effect of vertical load, tire inflation pressure and soil moisture content on power loss in tire under controlled soil bin conditions were investigated. Also a finite element model of tire-soil interaction in order to achieve a suitable model for predicting power loss in tire was created. Increasing the vertical load on the tire had a noteworthy impact on increasing the tire contact volume with the soil, reducing the percentage of slip, and increasing the rolling resistance; although, reducing the load on the tire had the opposite effect. At a constant inflation pressure, by increasing the vertical load on the tire, the amount of power loss due to the rolling resistance and the total power loss in the tire increased. Increase in soil moisture content increased the power loss caused by slip. Increasing the inflation pressure at a constant vertical load, also increasing the soil moisture content, led to an increase in the power loss caused by rolling resistance, and increase total power loss. The obtained error for estimating power loss of rolling resistance and total power loss was satisfactory and confirmed the acceptability of the model for power loss estimation.     

Transient dynamic response analysis of 3-D patterned tire rolling over cleat

Transient dynamic response of a rolling tire impacting with a small cleat is analyzed by an explicit finite element method. A 3-D tire model considering detailed tread blocks is used to accurately simulate the local tire-cleat impact process. The frictional dynamic contact problem is formulated by making use of total Lagrangian scheme and the penalty method. By imposing mass-proportional damping to only the tire parts showing the significant lateral deformation, the dynamic viscosity effect is artificially reflected. Time-history and frequency responses of the dynamic forces exerted on the tire axis are numerically predicted and assessed through the comparison with experimental results. As well as, the effects of the tire rolling speed and the inflation pressure on the transient dynamic response are parametrically investigated.     

Finite element modeling of tire/terrain interaction: Application to predicting soil compaction and tire mobility

Tire/terrain interaction has been an important research topic in terramechanics. For off-road vehicle design, good tire mobility and little compaction on terrain are always strongly desired. These two issues were always investigated based on empirical approaches or testing methods. Finite element modeling of tire/terrain interaction seems a good approach, but the capability of the finite element has not well demonstrated. In this paper, the fundamental formulations on modeling soil compaction and tire mobility issues are further introduced. The Drucker-Prager/Cap model implemented in ABAQUS is used to model the soil compaction. A user subroutine for finite strain hyperelasticity model is developed to model nearly incompressible rubber material for tire. In order to predict transient spatial density, large deformation finite element formulation is used to capture the configuration change, which combines with soil elastoplastic model to calculate the transient spatial density due to tire compaction on terrain. Representative simulations are provided to demonstrate how the tire/terrain interaction model can be used to predict soil compaction and tire mobility in the field of terramechanics.     

Tractive performance of a tread design for improved flexibility

The tractive performance of an 18.4R38 radial-ply tractor tire with increased flexibility in the tread area was compared to that of a standard tread design. Normal soil-tire interface stresses were measured at four locations on the lug surfaces of both tires operating on Decatur clay loam and Norfolk sandy loam soils. There was a tendency for the increased flexibility in the tread area to provide a higher net traction ratio at the same tractive efficiency as the standard tread design, especially on Decatur clay loam soil. The more flexible tread design reduced the magnitude of peak normal contact stresses across the tire width, which may have implications for reducing soil compaction without compromising tractive performance. The more flexible tire reduced the average normal contact stress by approximately 15% in the sandy loam soil and 23% in the clay loam soil for the range of operating conditions investigated.     

Development and evaluation of an in-situ tire testing facility with variable side slip angles

An in-situ tire test rig was developed for field research on tire tractive and maneuverability performances. The Single Wheel Tester (SWT) was mounted on a tractor and a tested wheel was driven by a hydromotor, along a frame of 3 m length. In the SWT, four load cells were utilized to measure longitudinal and lateral forces, input and self-aligning torques, and two optical counters were applied to calculate forward and angular velocities. Response Surface Methodology was used to execute experimental design and to analyze the collected data. Afterwards, reduced form of a 2 Factor Interaction model was extracted to predict rolling resistance using seven factors. The test results show that increasing the normal load and side slip angle will cause an increment of rolling resistance. The incremental growth rate of the rolling resistance due to the normal load increment was observed. At higher cone index values, increasing the angular velocity reduces the rolling resistance, although at lower cone index values, the effect of angular velocity on rolling resistance is in reverse order. In addition, the increasing moisture content effect on rolling resistance at lower side slip angle values was observed.     

A tire–ice model (TIM) for traction estimation

Increased traffic safety levels are of highest importance, especially when driving on icy roads. Experimental investigations for a detailed understanding of pneumatic tire performance on ice are expensive and time consuming. The changing ambient and ice conditions make it challenging to maintain repeatable test conditions during a test program. This paper presents a tire–ice contact model (TIM) to simulate the friction levels between the tire and the ice surface. The main goal of this model is to predict the tire–ice friction based on the temperature rise in the contact patch. The temperature rise prediction in the contact patch is based on the pressure distribution in the contact patch and on the thermal properties of the tread compound and of the ice surface. The contact patch is next classified into wet and dry regions based on the ice surface temperature and temperature rise simulations. The principle of thermal balance is then applied to compute the friction level in the contact patch. The tire–ice contact model is validated by comparing friction levels from simulations and experimental findings. Friction levels at different conditions of load, inflation pressure, and ice temperatures have been simulated using the tire–ice contact model and compared to experimental findings.     

Sensitivity analysis of tire-ice friction coefficient as affected by tire rubber compound properties

Previous studies show that the material properties of the rubber are among the most important factors when designing a tire. In this study, we investigated the effects of different rubber properties on tire performance on ice. A theoretical model that incorporates these tire material properties was developed. The model was used to estimate the height of the water film generated due to friction and the friction coefficient for both, dry and wet regions at the tire-ice contact patch. After validating the results using experimentally collected data, the model was used to perform a sensitivity analysis on the tire performance with respect to six material properties of the tread rubber: thermal conductivity, rubber density, Young’s modulus, specific heat, roughness parameter of the rubber, and radii of spherical asperities of the rubber. To study the effect of each parameter, the desired material property was varied within a specific range while the other parameters were kept constant. The results from this study show the sensitivity of the magnitude of the friction coefficient to the rubber material properties. The friction coefficient has a direct relationship with the density of the rubber and has an inverse relationship with Young’s modulus, specific heat, and roughness parameter.     

Theoretical and experimental analysis of the contact between a solid-rubber tire and a chassis dynamometer

We consider the problem of modeling the test where a solid-rubber tire runs on a chassis dynamometer for determining the tire rolling resistance characteristics.We state the problem of free steady-state rolling of the tire along the test drum with the energy scattering in the rubber in the course of cyclic deformation taken into account. The viscoelastic behavior of the rubber is described by the Bergströ m–Boyce model whose numerical parameters are experimentally determined from the results of compression tests with specimens. The finite element method is used to obtain the solution of the three-dimensional viscoelasticity problem. To estimate the adequacy of the constructed model, we compare the numerical results with the results obtained in the solid-rubber tire tests on the Hasbach stand from the values of the rolling resistance forces for various loads on the tire.     

Finite element analysis of tire traveling performance using anisotropic frictional interaction model

The traveling performance of off-the-road vehicles, such as construction machinery and exploration rovers, significantly depends on the interaction between the ground and the traveling mechanism, since inelastic ground deformation and frictional sliding phenomena are induced by the vehicle’s movement. In general, a tread surface causes anisotropic frictional interaction behavior on a macroscopic scale. In this study, an acceptable frictional interaction model was implemented to finite element method to rationally examine the anisotropic frictional interaction behavior between the tire and the ground. Finite element analysis of the single tire traveling performance, including certain slippage and side slip (skid), was then carried out to examine the effect of the anisotropic frictional interaction on the numerical results for the drawbar-pull and side force.     

Analytical model of longitudinal tire traction in snow

An analytical model to estimate longitudinal traction of a tire in snow was developed and verified to have good predictability in comparison with measurements. Snow traction of a tire is composed of four kinds of forces in this model: braking force attributable to snow compression, shear force of snow in void (space between tread blocks), frictional force, and digging force (edge effect generated by sipes and blocks). The mechanical characteristics of snow were considered in the prediction of braking force and shear force, but were not considered in the prediction of other forces. The contribution of shear force of snow in void and the frictional force was large in static traction (traction just before a tire slips). On the other hand, the contributions of digging force and frictional force were large in situations involving high slip ratios.