Steering forces on undriven tractor wheel

The steering forces on an undriven, angled wheel mounting a 6-16 8PR tire were measured on a wheel test carriage at zero camber angle and at 1.5 km/h forward speed in a soil bin with sandy clay loam soil. The lateral force developed was found to be a function of slip angle, normal load, and inflation pressure for a particular soil condition. An exponential relationship could estimate the coefficient of lateral force of the 6-16 tire. The coefficients of this equation were found to be linearly related to inflation pressure. Rolling resistance of the wheel tested was found to be a function of slip angle, normal load, and inflation pressure for the soil condition tested. A linear relationship existed between the rolling resistance and slip angle, where the coefficients were found to be a function of inflation pressure and normal load. The generalized equations developed in the present study for estimating coefficients of lateral force and rolling resistance by taking both the tire and operating parameters into account, were found to be reasonably good by looking at the high coefficient of determination between experimental and estimated values.     

Development and evaluation of an in-situ tire testing facility with variable side slip angles

An in-situ tire test rig was developed for field research on tire tractive and maneuverability performances. The Single Wheel Tester (SWT) was mounted on a tractor and a tested wheel was driven by a hydromotor, along a frame of 3 m length. In the SWT, four load cells were utilized to measure longitudinal and lateral forces, input and self-aligning torques, and two optical counters were applied to calculate forward and angular velocities. Response Surface Methodology was used to execute experimental design and to analyze the collected data. Afterwards, reduced form of a 2 Factor Interaction model was extracted to predict rolling resistance using seven factors. The test results show that increasing the normal load and side slip angle will cause an increment of rolling resistance. The incremental growth rate of the rolling resistance due to the normal load increment was observed. At higher cone index values, increasing the angular velocity reduces the rolling resistance, although at lower cone index values, the effect of angular velocity on rolling resistance is in reverse order. In addition, the increasing moisture content effect on rolling resistance at lower side slip angle values was observed.     

Modeling compaction in agricultural soils

Research was conducted to quantify the effect of tire variables (section width, diameter, inflation pressure); soil variables (soil moisture content, initial cone index, initial bulk density); and external variables (travel speed, axle load, number of tire passes) on soil compaction and to develop models to assess compaction in agricultural soils. Experiments were conducted in a laboratory soil bin at the Asian Institute of Technology in three soils, namely: clay soil (CS), silty clay loam soil (SCLS), and silty loam soil (SLS). A dimensional analysis technique was used to develop the compaction models. The axle load and the number of tire passes proved to be the most dominant factors which influenced compaction. Up to 13% increase in bulk density and cone index were observed when working at 3 kN axle load in a single pass using a 8.0–16 tire. Most of the compaction occurred during the first three passes of the tire. It was also found that the aspect ratio, tire inflation pressure and soil moisture content have significant effect on soil compaction. The initial cone index did not show significant effect. The compaction models provided good predictions even when tested with actual field data from previous studies. Thus, using the models, a decision support system could be developed which may be able to provide useful recommendations for appropriate soil management practices and solutions to site-specific compaction problems.     

Tractor tire aspect ratio effects on soil bulk density and cone index

A 580/70R38 tractor drive tire with an aspect ratio of 0.756 and a 650/75R32 tire with an aspect ratio of 0.804 were operated at two dynamic loads and two inflation pressures on a sandy loam and a clay loam with loose soil above a hardpan. Soil bulk density and cone index were measured just above the hardpan beneath the centerline and edge of the tires. The bulk densities were essentially equal for the two tires and cone indices were also essentially equal for the two tires. Soil bulk density and cone index increased with increasing dynamic load at constant inflation pressure, and with increasing inflation pressure at constant dynamic load. In comparisons of the centerline and edge locations, soil bulk density and cone index were significantly less beneath the edge than beneath the centerline of the tires. Soil compaction is not likely to be affected by the aspect ratio of radial-ply tractor drive tires when aspect ratios are between 0.75 and 0.80.     

Sources of variability in traction data

A 18.4R38 tyre was tested at 124 kPa inflation pressure, approximately 24 kN axle load in a firm and in a tilled Yolo-loam soil using (i) constant slip, (ii) constant draught, (iii) varying slip and (iv) varying draught tyre testing procedures. The results indicated that the constant slip test procedure leads to repeatable and consistent results whereas a variable slip test procedure leads to considerable scatter in the data. The constant draught test procedure yielded acceptable results. Varying slip appeared to influence the system dynamics much more than varying draught during tyre testing. An accurate method of predicting “true rolling radius” and “true slip” for an assumed zero condition is presented. The concept of motion resistance, its variability due to assumed zero conditions, and possible interpretations are discussed. The traction test data indicates that the motion resistance is not constant but varies with slip.     

Soil compaction and tires for harvesting and transporting sugarcane

Four tire types (A, block-shape tread; B, rib-shape tread; C, low-lug tread; D, high-lug tread) used to harvest and transport sugarcane were compared regarding the compaction induced to the soil. Tires were tested at three inflation pressures (207, 276, 345 kPa) and six loads ranging from 20 to 60 kN/tire. Track impressions were traced, and 576 areas were measured to find equations relating inflation pressure, load, contact surface and pressure. Contact surface increased with increasing load and decreasing inflation pressure; however, the contact pressure presented no defined pattern of variation, with tire types A and B generating lower contact pressure. The vertical stresses under the tires were measured and simulated with sensors and software developed at the Colombian Sugarcane Research Center (Cenicaña). Sensors were placed at 10, 30, 50 and 70 cm depth. Tire types A and B registered vertical stresses below 250 kPa at the surface. These two tires were better options to reduce soil compaction. The equations characterizing the tires were introduced into a program to simulate the vertical stress. Simulated and measured stresses were adjusted in an 87–92% range. Results indicate a good correlation between the tire equations, the vertical stress simulation and the vertical stress measurement.     

Experimental analysis of vertical soil reaction and soil stress distribution under off-road tires

In this study, the vertical soil reaction acting on a driven wheel was measured by strain gages bonded to the left rear axle of a 2WD tractor driven under steady-state condition on different soil surfaces, tractor operations, and combinations of static wheel load and tire inflation pressure. In addition, the measurements of radial and tangential stresses on the soil–tire interface were made simultaneously at lug’s face and leading side near the centerline of the left rear tire using spot pressure sensors. The experimental results indicate that the proposed method of vertical soil reaction measurement is capable of monitoring the real-time vertical wheel load of a moving vehicle and provides a tool for further studies on vehicle dynamics and dynamic wheel–soil interaction. Furthermore, the measured distributions of soil stresses under tractor tire could provide more real insight into the soil–wheel interactions.     

Rolling deformation of truck tires: Measurement and analysis using a tire sensing approach

Measurements on rolling tire deformation provide deep insights into the mechanism of generating tire forces and moments. For free rolling tires, substantial attention has been given to the rolling resistance because of its significant impact on the fuel consumption and CO₂ emissions. This paper attempts to investigate the rolling resistance force through measurements of the rolling deformation of truck tires using a tire sensing approach. An optical tire sensor system is used to measure rolling tire deformation, which includes the deformed inner profile, sidewall deformation, and tread deformation. Measurements were conducted on a test truck for both new and used tires. In addition, the influences from operational factors such as wheel load and inflation pressure on tread deformation were examined and analyzed.     

Dynamic load and inflation pressure effects on contact pressures of a forestry forwarder tire

A Trelleborg Twin 421 Mark II 600/55-26.5 steel-reinforced bias-ply forwarder drive tire at inflation pressures of 100 and 240 kPa and dynamic loads of 23.9 and 40 kN was used at 5% travel reduction on a firm clay soil. Effects of dynamic load and inflation pressure on soil–tire contact pressures were determined using six pressure transducers mounted on the tire tread. Three were mounted on the face of a lug and three at corresponding locations on the undertread. Contact angles increased with decreases in inflation pressure and increases in dynamic load. Contact pressures on a lug at the edge of the tire increased as dynamic load increased. Mean and peak pressures on the undertread generally were less than those on a lug. The peak pressures on a lug occurred forward of the axle in nearly all combinations of dynamic load, inflation pressure, and pressure sensor location, and peak pressures on the undertread occurred to the rear of the axle in most of the combinations. Ratios of the peak contact pressure to the inflation pressure ranged from 0 at the edge of the undertread for three combinations of dynamic load and inflation pressure to 8.39 for the pressure sensor on a lug, near the tire centerline, when the tire was underinflated. At constant dynamic load, net traction and tractive efficiency decreased as inflation pressure increased.     

Soil stress state orientation beneath a tire at various loads and inflation pressures

Stress state transducers (SSTs) were used to determine the orientation of the major principal stress, σ₁, in soil beneath the centeline of an 18.4R38 radial-ply R-1 drive tire operated at 10% slip. Two soils, a sandy loam and a clay loam, were each prepared twice to obtain two density profiles. One profile of each soil had a hardpan and the soil above the hardpan was loose. The soil in the second profile was loosely tilled. The stress state was determined at a depth of 358 mm in the sandy loam and 241 mm in the clay loam soil. The tire was operated at two dynamic loads (13.2 and 25.3 kN), each at two levels of inflation pressure (41 and 124 kPa). When the orientation of σ₁ was determined directly beneath the axle, the mean angles of tilt in the direction of travel ranged from 6 to 23 degrees from vertical. Inflation pressure did not significantly affect the angle when the dynamic load was 13.2 kN in the sandy loam soil, and neither inflation pressure nor dynamic load significantly affected the angle in the clay loam soil. When the dynamic load was 25.3 kN in the sandy loam soil, the orientation of the major principal stress determined directly beneath the axle was tilted significantly more in the direction of travel when the tire was at 41 kPa inflation pressure than when at 124 kPa. These changes in stress orientation demonstrate the importance of measuring the complete stress state in soil, rather than stresses along only one line of action. The changing orientation of σ₁ as the tire passes over the soil indicates the soil undergoes kneading and supports future investigation of the contribution of changes in stress orientation to soil compaction.     

Tire footprint characteristics as a function of soil properties and tire operations

The main objective of the following presentation is to examine the possibility of predicting agricultural tire footprint parameters under different operational conditions. The experimental part of the research involved the operation of two agricultural transport tires on two soils, under variations of tire load, inflation pressures and soil moisture contents. Results obtained show that tire footprint parameters, such as contact area, length, width and sinkage, can be reliably predicted using multifactorial linear and total regressions, within the range of recommended tire loads, inflation pressures and soil moisture contents around the plastic limit.     

Modelling in FEM the soil pressures distribution caused by a tyre on a Rhodic Ferralsol soil

Tyre traffic over soil causes non-uniform ground pressures across the tyre width and along the soil–tyre contact area. The objective of this paper was to obtain in the topsoil the shape, magnitudes, distribution and transmission in depth of the ground pressures from a finite element model of soil compaction. The influence of tyre inflation pressure, tyre load and soil water content over the pressures propagation in the soil was analysed. The model shows how to low inflation pressure the tyre carcass supports most of the total load and the biggest peak pressures are distributed in the tyre axes when it traffics over firm soil. For high inflation pressure the incremented stiff causes that pressure is distributed with parabolic shape. In wet soil the inflation pressure does not influence on the ground pressure distribution, this depends only on the tyre load. The inflation pressure and tyre load changed the shape of the vertical pressures distribution on the surface of a hard dry soil, but these variables did not affect the distribution of vertical stresses in a soft wet soil or below a depth of 0.15 m.     

Thrust and slip of a low-pressure tire on compressible ground by the compression-sliding approach

Driving wheels with low-pressure lugged tires are standard propulsion components of wheeled off-road vehicles. Such wheels have been mostly treated in theory as shorter tracks or even as “black boxes”. These procedures, however, appear not to be necessary since an updated theory of thrust generation, based on experiments with double-plate meter, was presented at the 2008 ISTVS Turin conference. This theory is based on the compaction-sliding (CS) concept, which claims that the rearward displacement of soil, a reason for slip, starts as horizontal soil compression by lugs (C-stage at lower thrust), followed by the slide of sheared off soil blocks (S-stage at higher thrust). The thrust in terms of ISTVS Standards equals gross tractive effort minus internal rolling resistance of a tire. The resultant thrust of a tire equals the sum of component thrusts of individual soil segments. The respective technique provides thrust-slip curves, which reflect tire size, loading, inflation pressure and tread pattern design, e.g. tread density, lug angle, pitch, height and tire casing lay-out and thus can be useful notably in assessing the traction properties of new tire designs. Concerning the evaluation of tire traction tests or similar applications, the CS approach offers a simplified version of thrust-slip formula (G-function), which complies with the CS concept and is easy to use.     

Effects of reduced inflation pressure and vehicle loading on off-road traction and soil stress and deformation state

Field experiments on off-road vehicle traction and wheel–soil interactions were carried out on sandy and loess soil surfaces. A 14 T, 6 × 6 military truck was used as a test vehicle, equipped with 14.00-20 10 PR tyres, nominally inflated to 390 kPa. Tests were performed at nominal and reduced (down to 200 kPa) inflation pressures and at three vehicle loading levels: empty weight, loaded with 3.6 and 6.0 T mass (8000, 11,600 and 14,000 kg, respectively). Traction was measured with a load cell, attached to the rear of the test vehicle as well as to another, braking vehicle. Soil stress state was determined with the use of an SST (stress state transducer), which consists of six pressure sensors. Soil surface deformation was measured in vertical and horizontal directions, with a videogrammetric system. Effects of reduced inflation pressure as well as wheel loading on traction and wheel–soil interactions were analyzed. It was noticed that reduced inflation pressure had positive effects on traction and increased stress under wheels. Increasing wheel load resulted in increasing drawbar pull. These effects and trends are different for the two soil surfaces investigated. The soil surface deformed in two directions: vertical and longitudinal. Vertical deformations were affected by loading, while longitudinal were affected by inflation pressure.     

Soil displacement beneath an agricultural tractor drive tire

Soil strain transducers were used to determine strain in an initially loose sandy loam soil in a soil bin beneath the centerline of an 18.4R38 radial-ply tractor drive tire operating at 10% travel reduction. The initial depth of the midpoints of the strain transducers beneath the undisturbed soil surface was 220 mm. Strain was determined in the vertical, longitudinal, and lateral directions. Initial lengths of strain transducers were approximately 118 mm for the longitudinal and lateral transducers and 136 mm for the vertical transducer. The tire dynamic load was 25 kN and the inflation pressure was 110 kPa, which was a recommended pressure corresponding to the load. In each of four replications, as the tire approached and passed over the strain transducers, the soil first compressed in the longitudinal direction, then elongated, and then compressed again. The soil was compressed in the vertical direction and elongated in the lateral direction. Mean natural strains of the soil following the tire pass were −0.200 in the vertical direction, +0.127 in the lateral direction, and −0.027 in the longitudinal direction. The mean final volumetric natural strain from the strain transducer data was −0.099, which was only 35% of the mean change in natural volumetric strain calculated from soil core samples, −0.286. This difference likely resulted from the greater length of the lateral strain transducer relative to the 69 mm lateral dimension of the soil cores. The strain transducer data indicated the occurrence of plastic flow in the soil during one of the four replications. These results indicate the complex nature of soil movement beneath a tire during traffic and emphasize a shortcoming of soil bulk density data because soil deformation can occur during plastic flow while soil bulk density remains constant.     

Slip-based experimental studies of a vehicle interacting with natural snowy terrain

As longitudinal slip affects vehicle–pavement interactions on roads and hard surfaces, so too does it play an important role in interactions between vehicles and soft terrains, including snow. Although many slip-based models have been developed recently for tire–snow interactions (e.g., [1] and references cited therein), these models have only been partially validated, due to a lack of relevant experimental data. This paper presents comprehensive data from tests that were performed using a newly-developed test vehicle traversing natural snowy terrain, over a wide range of values for longitudinal slip, vertical load and torque via an effective accelerate/brake maneuver. Drawbar pull, motion resistance, wheel states and tire stiffness were presented as a function of slip; tire sinkage was obtained using a laser profilometer; strength and depth of snow were found using a snow micropenetrometer. The effects of the rear tire going over snow compacted by the front tire were also studied. The maximum traction force normalized by the vertical load is found to be ≈0.47, maximum motion resistance normalized by the vertical load is ≈0.4. Comparison of the trend and order-of-magnitude of test results with those from existing slip-based numerical model [1] shows good comparison in motion resistance, tire sinkage, and longitudinal stiffness, but indicates that a better traction model is needed to improve the comparison.     

Measurement of contact area, contact pressure and compaction under tires in soft soil

This paper reports about measurements of the contact area of agricultuural tires in a soil bin. Four tires of the dimensions 12.5/80-18, 13.6–28, 16.9–34 and 16.9–26 were tested on a soft sandy loam. Because the existing models for predicting the footprint are complicated, a simplified model has been established, yielding good results. Measured different contact areas of all four tires are nearly constant related to wheel load except for a small increase at higher loads. Using rated loads and applying the appropriate inflation pressure, the ground pressure of a group of similar tires in loose sandy loam is independent of the tire dimensions. Measured soil compaction under at tire a various wheel loads is compared with results obtained by a mathematical model.     

Effects of tyre inflation pressure and forward speed on vibration of an unsuspended tractor

Relationships among intensity of vibrations, tractor speed, soil moisture content and tyre inflation pressure are important for the design of tractor suspension systems. This study was designed to evaluate the effect of tyre inflation pressure and forward speed on tractor vibration in the paddy fields of Southern China by using a two-wheel-drive unsuspended tractor with different combinations of forward speed, tyre inflation pressure and soil moisture content. During experiments, the vertical vibration accelerations in front and rear axles and triaxial vibration accelerations of the tractor body were measured using three accelerometers. Fourier analysis was applied to determine root mean square acceleration values in the low frequency range from 0.1 to 10 Hz. The results of the study indicate that tractor vibration is strongly affected by changing forward speed and tyre inflation pressure, and especially by changing forward speed and rear tyre inflation pressure. The research also shows the variation in the pattern of vibration intensity especially at the tractor’s front axle when field soil moisture content is changed.     

Steering forces on undriven, angled wheels

The steering forces at low speed and zero camber angle were measured on undriven, angled wheels using tyres with no tread. The forces were measured in a soil bin using a moist loam soil at different levels of compaction. It was found that the coefficient of side force relative to the wheel was related to slip angle by an exponential relationship. Coefficient of rolling resistance relative to the wheel was a linear function of slip angle in the region zero to 20° but was an irregular function of slip angle at higher angles. The effects of tyre size, load, inflation pressure and soil condition were modelled well using different versions of the tyre mobility number. The most successful version of mobility number was one which incorporated both soil cohesion and internal friction angle. The coefficients of the exponential and linear relationships mentioned above were predicted with varying degrees of success using mobility number.     

The determination of deflection and contact characteristics of a pneumatic tire on a rigid surface

The contact pressure, contact area, contact width, contact length and vertical deflection of a pneumatic tire on a rigid surface depend on tire size, load and inflation pressure and can be derived by means of mathematical expressions. These expressions have been widely utilized and checked in practice for different tires.