板桁结构考虑局部屈曲空间计算的横向带板段单元法

用有限个横条带法构造了板桁组合结构板段考虑局部屈曲的空间位移模式,基于三维连续体的虚功增量方程,导出了横向条带板段单元的ＵＬ列式,并考虑了板段单元位形变化的影响,此计算方法自由度少,计算精度高,能用于大型板桁结构的几何非线性分析,文末计算了广东西江桥板桁组合结构模型梁,计算结果与实测结果吻合较好。     

一种适用于下承式钢桁结合桥计算的板梁组合单元

下承式钢桁结合桥具有建筑高度较低、行车时燥声、震动较小、刚度较大等优点,是高速铁路桥梁中比较理想的结构形式之一。为了能较合理和方便地分析下承式钢桁结合桥的力学行为,本文提出了一种考虑板梁共同作用和相对滑移的板梁组合单元。该单元以矩形板的4个结点的结点位移和板梁结合面3个点的相对滑移作为单元的基本自由度,板的位移模式通过对常规4结点矩形平板壳单元的形函数修正得到,梁的位移模式则根据板和梁之间的变形协调条件来确定。文末的算例表明,本文的解与试验结果和通用工程软件解较为吻合,说明了本文理论和方法的正确性。     

基于高阶剪切变形理论的四边形求积元板单元及其应用

近年来由各类新型复合材料或功能梯度材料构成的板结构在工程领域得到了广泛应用,其显著特点是材料性能沿板厚变化.为合理考虑横向剪切应变,许多学者基于Reddy高阶剪切变形理论,构建了不同的有限元单元对该类板结构进行分析,但其中满足$C^{1}$连续条件的单元相对较少.本文基于Reddy高阶剪切变形理论,采用求积元方法,建立了$C^{1}$连续的四边形板单元.利用该单元对均质材料、复合材料、功能梯度材料构成的等厚度矩形板、变厚度矩形板及等厚度斜板的线弹性弯曲和自由振动问题进行了计算分析,并与现有文献中的相应计算结果进行了对比.研究表明:基于高阶剪切变形理论的四边形求积元板单元具有较高的计算效率和良好的适应性,文中各类材料构成的等变厚度矩形板及等厚度斜板均只需1个单元即可得到理想的计算结果.对于等/变厚度矩形板,可仅使用9$\times$9个积分点,而对于等厚度斜板,随着斜角的增大,所需积分点的数目逐渐增多至15$\times $15.该四边形求积元板单元可进一步用于新型复合材料板的非线性分析.      

空间杆系与叠层板组合结构的非线性稳定分析

本文用非线性有限元法研究一种空间杆系与复合材料叠层板组合结构的非线性稳定问题，将杆系离散成空间梁柱单元，将复合材料叠层板离散成复合材料叠层板单元，并考虑了几何非线性和板的成层正交各向异性性质。为了获得较高的计算效率并顺利通过稳定临界点，求解非线性平衡方程采用了变增量步长和柱面弧长法迭代策略。在考证了程序的正确性之后，具体分析了几个工程模型，得出了于工程设计有益的结论。     

空间杆系与叠层板组合结构的非线性稳定分析

本文用非线性有限元法研究一种空间杆系与复合材料叠层板组合结构的非线性稳定问题。将杆系离散成空间梁柱单元，将复合材料叠层板离散成复合材料叠层板单元，并考虑了几何非线性和板的成层正交各向异性性质。为了获得较高的计算效率并顺利通过稳定临界点，求解非线性平衡方程采用了变增量步长和柱面弧长法迭代策略。在考证了程序的正确性之后，具体分析了几个工程模型，得出了于工程设计有益的结论。     

一种精确积分的四结点板弯曲单元

本文从Ｍｉｎｄｌｉｎ／Ｒｅｉｓｓｎｅｒ理论出发,采用一种新的平行四边形母单元和相应的形函数推导四结点板弯曲单元刚度矩阵的精确积分解。弯曲应变和横向剪切应变分别采用不同的插值公式构成单元刚度矩阵。理论和算例分析表明本文方法克服了“闭锁”现象并能应用于很薄的板,单元刚度矩阵计算速度比采用数值积分计算的同类单元的快四倍。     

用于多种夹层板等效的有限元分析法

针对夹层板力学性能解析法难于计算复杂结构的夹层板且通用性差的问题,本文采用有限元分析法研究了夹层板性能的等效方法。对夹层板的代表体单元模型施加位移约束,模拟弯曲变形时线性独立的应变分量和弯曲内力;根据夹层板内力与应变的本构关系,求出刚度矩阵;最后由刚度矩阵得出宏观等效弹性常数,从而把夹层板等效成连续材料的单层板单元。将该方法与解析法计算结果进行比较得到的夹层板单元四个主要弹性常数误差在0.2%以内,验证了该方法的有效性;另外采用该方法等效三种典型结构夹层板,比较实际模型和等效模型的弯曲响应,得到的误差均在1.4%以内,表明该方法在不考虑复杂多变的夹芯结构时具有通用性。     

圆板非线性振动有限元分析的一种迭代方法

同时考虑横向振动和板平面内的运动,用3节点有限元研究均匀圆板的轴对称大振幅非线性振动,构造了一个避免发散加速收敛的平均迭代法,并将计算结果与文献的已有结果做了比较。     

八节点非协调实体板单元

通过为三维实体等参元附加非协调位移模式,构造了能反映横向剪切变形影响的非协调实体板单元.单元采用完全的三维应力应变本构关系和实体几何描述,可给出板的三维应力状态.为确保不规则单元通过分片检验,推导了显式表达的非协调位移修正项.算例表明:单元无多余零能模式,对中厚板可给出满意的计算精度.     

聚碳酸酯板裂纹顶端的弹塑性研究

本文研究了聚碳酸酯板的延性断裂特征;提出了修正的强化Dugdale条带屈服模型,并用实验-数值计算混合法确定了强化弹塑性材料裂纹顶端附近的应力场参数.实验测定结果与理论等色线,计算的裂纹前沿塑性区长度相符合.由此,验证了所提出的修正强化Dugdale条带屈服模型的合理性.     

双主梁钢板组合连续梁桥翼缘有效宽度及几何构造参数分析

双主梁式钢板组合梁桥，在中小跨径桥梁中有良好的应用前景．由于其钢板主梁间距较大，桥面板正应力在桥横向的分布更加不均匀，剪力滞效应显著．结合工程实例，通过有限元分析，计算了双主梁式钢板组合梁桥的桥面板翼缘有效宽度．为保证桥面板作为主梁受压翼缘的利用率，依据我国现行规范，结合有效宽度计算结果推导了双主梁式钢板组合梁桥主梁间距的计算公式，根据统计资料，对桥梁宽跨比及主梁间距与桥面宽度的比值等几何构造参数进行了初步分析，以期为双主梁钢板组合梁桥构造设计提供参考依据．     

钢桁腹式混凝土组合箱梁翼板纵向应力的计算方法研究

为研究钢桁腹式混凝土组合箱梁翼板纵向应力沿横桥向的分布情况,运用有限元软件ANSYS建立一座35m等截面简支钢桁腹式混凝土组合箱梁的有限元模型,考虑斜向腹杆杆力作用会使翼板产生附加轴力及相应的附加应力,故利用能量变分法原理推导出组合箱梁的翼板纵向弯曲应力和纵向附加应力计算公式,并据此探讨适用于计算组合箱梁的翼板纵向应力的方法。将有限元值和理论值进行比较,吻合程度良好。研究结果表明,组合箱梁的下翼板纵向应力可采用纵向弯曲应力计算公式进行计算;为获得组合箱梁的翼板附加轴力,可将组合箱梁的钢桁腹杆和混凝土纵梁取出,认为两者通过节点构造共同构成平面桁架,翼板附加轴力即为平面桁架的弦杆杆力;组合箱梁的上翼板纵向应力可通过纵向弯曲应力和经修正的纵向附加应力叠加获得。     

大跨度斜拉桥动力特性分析

本文提出一种计算大距度钢桁梁斜拉桥动力特性的方法。文中分别采用桁段有限单元、空间梁元、空间杆元计算斜拉桥中桁架，桥塔、拉索的刚度矩阵与质量矩阵，采用子空间迭代法求解特征方程，所得结果可供设计参考。     

Large rotations in first-order shear deformation FE analysis of laminated shells

The paper deals with the geometrically non-linear analysis of laminated composite beams, plates and shells in the framework of the first-order transverse shear deformation (FOSD) theory. A central point of the present paper is the discussion of the relevance of five- and six-parameter variants, respectively, of the FOSD hypothesis for large rotation plate and shell problems. In particular, it is shown that the assumption of constant through-thickness distribution of the transverse normal displacements is acceptable only for small and moderate rotation problems. Implications inherent in this assumption that are incompatible with large rotations are discussed from the point of view of the transverse normal strain-displacement relations as well as in the light of an enhanced, accurate large rotation formulation based on the use of Euler angles. The latter one is implemented as an updating process within a Total Lagrangian formulation of the six-parameter FOSD large rotation plate and shell theory. Numerical solutions are obtained by using isoparametric eight-node Serendipity-type shell finite elements with reduced integration. The Riks-Wempner-Ramm arc-length control method is used to trace primary and secondary equilibrium paths in the pre- and post-buckling range of deformation. A number of sample problems of non-linear, large rotation response of composite laminated plate and shell structures are presented including symmetric and asymmetric snap-through and snap-back problems.     

正交异性钢桥面板轮载横向效应的解析分析方法

在分析正交异性钢桥面板构造特点的基础上,将轮载影响范围内的桥面板简化为弹性支撑的平面框架,建立了正交异性钢桥面轮载横向效应的解析分析模型,推导了纵肋弹性支撑刚度和车轮荷载集度等效计算方法,提出了桥面板与U肋交接位置处横向弯曲应力的解析公式,讨论并明确了影响桥面板横向弯曲应力峰值的关键敏感影响因素,并以某钢箱梁为例证明了本文算法的合理性。研究发现,本文方法计算得到桥面板与U肋相交位置的横向应力值与有限元结果相差不超过10%,证实了本文算法的正确性,也为正交异性钢桥面的初步设计提供了极大的方便;正交异性钢桥面板的横向轮载应力随U肋厚度和高度增加而增大,但随顶板厚度和横隔板间距增大而减小;相对而言,顶板内横向拉应力受顶板厚度的影响最为显著,对腹板倾角和U肋腹板厚度的变化并不敏感。     

桁架板等效刚度分析

桁架材料的连续介质等效模型的研究已有相当基础,而工程中桁架材料往往以类板结构形式出现,其变形表现出明显的弯曲特征。将类板桁架材料采用弯曲板模型模拟,研究合理的方法确定等效板模型的刚度具有重要意义。本文在基于Kirchhoff假定的小挠度薄板弹性理论框架下,研究了类板桁架材料的等效弯曲薄板模型,提出了确定薄板模型等效刚度的基于Dirichlet位移边界条件的代表体元法,给出了确定各刚度系数所对应的代表体元的边界位移形式。具体计算了几种典型形式桁架板的等效刚度,并采用有限元离散模型和实验技术分析了桁架板在一定的边界约束和荷载作用下的响应,并与等效板模型的分析结果进行了对比。结果表明,在响应分析中,具有等效刚度的薄板模型可准确模拟类板桁架材料;连续介质板等效刚度计算的积分法不能给出准确的桁架板等效刚度,而基于Dirichlet位移边界条件的代表体元法获得的等效板的刚度具有很高的精度。     

Stochastic nonlinear bending response of laminated composite plates with system randomness under lateral pressure and thermal loading

In this paper, the effect of sensitivity of randomness in system parameters on the nonlinear transverse central deflection response of laminated composite plates subjected to transverse uniform lateral pressure and thermal loading is examined. System parameters such as the lamina material properties, expansion of thermal coefficients, lamina plate thickness and lateral load are modelled as basic random variables. A higher order shear deformation theory in the von-Karman sense is used to model the system behavior of the laminated plate. A direct iterative-based C ⁰ nonlinear finite element method in conjunction with the first-order perturbation technique developed by the authors is extended for thermal problem to obtain the second-order response statistics, i.e., mean and variance of the nonlinear transverse deflection of the plate. Typical numerical results of composite plates with temperature independent and dependent material properties subjected to uniform temperature and combination of uniform and transverse temperature are obtained for various combinations of geometric parameters, uniform lateral pressures, staking sequences and boundary conditions. The results have been compared with those available in the literature and an independent Monte Carlo simulation.     

低速冲击下复合材料合板的响应过程模拟

运用一种精度较高的高阶位移模型分析了复合材料层合板在低速击下的响应过程,该位移模型能够同时考虑层间正应力和横向剪应力,另外,采用修正的Hertz接触定律与Newmark积分方法相结合,建立了冲击接触的有限元模型,本文的数值模拟计算结果与解析结果相比较证明了该方法的有效和精确性。     

Dynamic analysis of composite plate with multiple delaminations based on higher-order zigzag theory

In a recent paper, Cho and Kim [Journal of Applied Mechanics] proposed a higher-order cubic zigzag theory of laminated composites with multiple delaminations. The proposed theory is not only accurate but also efficient because it work with a minimal number of degrees of freedom with the application of interface continuity conditions as well as bounding surface conditions of transverse shear stresses including delaminated interfaces. In this work, we investigate the dynamic behavior of laminated composite plates with multiple delaminations. A four-node finite element based on the efficient higher-order zigzag plate theory of laminated composite plates with multiple delaminations is developed to refine the prediction of frequencies, mode shape, and time response. Through the dynamic version of the variational approach, the dynamic equilibrium equations and variationally consistent boundary conditions are obtained. Natural frequency prediction and time response analysis of a composite plate with multiple delaminations demonstrate the accuracy and efficiency of the present finite element method. To prevent penetration violation at the delamination interfaces, unilateral contact constraints by Lagrange multiplier method are applied in the time response analysis. The present finite element is suitable for the prediction of dynamic response of thick composite plates with multiple and arbitrary shaped delaminations.     

Nonlinear transient response of strain rate dependent composite laminated plates using multiscale simulation

The effects of strain rate dependency and inelasticity on the transient responses of composite laminated plates are investigated. A micromechanics model which accounts for the transverse shear stress effect, the effect of strain rate dependency and the effect of inelasticity is used for analyzing the mechanical responses of the fiber and matrix constituents. The accuracy of the micromechanics model under transverse shear loading is verified by comparing the results with those obtained using a general purpose finite element code. A higher order laminated plate theory is extended to capture the inelastic deformations of the composite plate and is implemented using the finite element technique. A complete micro–macro numerical procedure is developed to model the strain rate dependent behavior of inelastic composite laminates by implementing the micromechanics model into the finite element model. Parametric studies of the transient responses of composite plates are conduced. The effects of geometry, ply stacking sequence, material models, boundary conditions and loadings are investigated. The results show that the strain rate dependency and inelasticity influence the transient responses of composite plates via two significantly different mechanisms.