混合边界约束多层矩形薄板的自由振动解析解研究

构造带有补充项的双重正弦傅里叶级数作为振型函数通解,来研究混合边界约束多层矩形薄板的自由振动特性。考虑振型函数中待定常数的物理意义,再结合多层矩形薄板的边界条件,简化得到了具体混合边界约束多层矩形薄板的振型函数。结合控制方程、未用的边界条件和协调条件,建立了求解频率的解析方程组,将其转化为广义特征值问题求其量纲为一的频率。选取参数计算并与文献结果进行了对比,二者吻合良好,证明了本文所采用方法以及提出通解的正确性。该通解不但可以满足多层矩形薄板的任意边界约束条件,而且其中的各个待定常数具有明确的物理意义,同时该通解也能用于研究多层矩形薄板的弯曲和稳定问题,从而使得多层矩形薄板问题的求解简单化、统一化、规律化。     

各向异性矩形板的剪切屈曲分析

根据各向异性矩形薄板剪切屈曲横向位移函数的微分方程建立了一般性的解析解。该一般解包括三角函数和双曲线函数组成的解,它能满足四个边为任意边界条件的问题;该一般解还包括代数多项式解,它能满足四个角的边界条件问题。因此,这一解析解可用于精确地求解任意边界的各向异性矩形板的剪切屈曲问题。其中待定常数可由四边和四角的边界条件来确定,由此得出的齐次线性代数方程系数矩阵行列式等于零可以求得各阶临界载荷及其屈型。结合配点法,利用变形的对称和反对称性,以及对称迭层正方形板均可使计算更简单。以四边平夹的对称角铺设复合材料迭层板为例进行了计算和讨论。     

阶梯式矩形板的振动

用奇异函数建立阶梯式矩形板自由振动和强迫振动的微分方程并求得其通解，用Ｗ算子给出振型函数的表达式及常见支承条件下板的频率方程，本文解可用于多种边界条件的板。     

混合边界矩形薄板的自由振动

本文用离散型最小二乘法和配点法分析混合边界矩形薄板的自由振动问题.所提出的振型函数的试函数精确满足板内的控制微分方程和部分边界条件.计算特征值时只需在部分边界上配点即可.这样工作量少,精度较高,算例结果令人满意.     

三边简支一边自由混凝土矩形薄板的热弯曲

基于薄板的小挠度理论和叠加原理,考虑横向变温情况,将温度作用下的三边简支一边自由矩形薄板看作是面内温差作用下的四边简支矩形薄板和自由边上挠度作用下的三边简支一边自由矩形薄板的叠加,得到了温度作用下三边简支一边自由混凝土矩形薄板的挠度和弯矩解析解.首先通过在自由边界上试设具有待定参数的挠度函数,采用李维解法推导出三边简支一边自由矩形薄板在自由边界挠度作用下的挠度方程;其次利用横向变温作用下四边简支矩形薄板的求解得到待定参数;再采用叠加原理得出横向变温作用下三边简支一边自由矩形薄板的挠度和弯矩解析解;最后利用MATLAB编制程序得到了横向变温作用下三边简支一边自由矩形薄板的计算系数用表,为工程结构中三边简支一边自由混凝土矩形薄板在热环境下的设计计算提供了理论依据.     

角点悬空弯曲厚矩形板的边界积分法

在边界积分法中引用了拟基本系统矩形板,在该拟基本系统与实际系统之间应用功的互等定理,得到一挠曲面方程的积分表达式,只要对此表达式进行极简单的积分便可得到该挠曲面方程,这比直接求解Reissner挠度控制方程要简单,边界积分法的求解过程概念清晰,计算伊始便给出了挠曲面方程的总体表达式.以Reissner厚板理论为基础,应用边界积分法研究了角点悬空厚矩形板的弯曲问题,给出了在集中荷载作用下两邻边固定另两邻边自由且角点悬空弯曲厚矩形板的封闭解析解,并给出了相应的数据和图表以供工程上的应用和参考.     

夹紧矩形板拉伸及角点应力奇异性分析的积分方程方法

二对边夹紧矩形板拉伸(压缩)时的角点应力奇异性,最近由Gupta精确解决,他的方法比较特殊,难于推广一般情形.本文采用单裂纹基本解,并结合使用无限板条的Fourier变换通解,把夹紧无限板条的二条平行裂纹问题,化归为解一组柯西型奇异积分方程,在此基础上让裂纹与夹紧边界相交而割出所求的矩形板问题,进而对积分核作渐近分析,精确地求得了角点的应力奇异性特征方程,使问题获得解决.本文方法可推广至一般角点的分析.     

不连续Reissner矩形板的自由振动

用分区加权残值法研究Ressner矩形板在几何形状,边界条件等有突变时的自由振动问题,将研究对象按照结构几何形状和边界条件的具体情况划分为若干子域,在每个子域内用不同的试函数代入该域的内的控制方程到内部残值,并代入板的边界条件和各子域的协调条件得到边界残值和连续性残值,然后用最小二乘法消除残值,得到特征方程,文中讨论了该方法的收敛性和计算精度,求解了开孔矩形板的固有频率,并与已有结果进行了比较,结果表明：？该方法收敛性好,精度较高,适用范围广。     

压电功能梯度板自由振动的三维解

基于三维弹性理论和压电理论，导出了有限长矩形压电功率梯度板的动力学方程及相应的边界条件，并用幂级数展开法进行了求解，得到了压电功能梯度板自由振动的三维精确解公式，求解了自由振动的固有频率，并分析了压电系数的梯度变化对不同电学边界条件下压电板的自由振动频率的影响，结果可用于校核不同的近似理论及理解压电结构的动态行为。     

一边简支二角点支承的矩形板弯曲

在分析求解条件完备性的基础上将矩形板的弯曲划分为广义静定问题和广义超静定问题，分别采用直接求解和叠加法解决了一边简支一角点支承和一边简支二角点支承的矩形板在板面分布荷载、板边分布荷载、角点集中力作用下以及角点支承产生支座沉陷时的弯曲。计算表明这种解法收敛快，计算精度高，适用范围广     

FREE VIBRATION OF ANISOTROPIC RECTANGULAR PLATES BY GENERAL ANALYTICAL METHOD

According to the differential equation for transverse displacement function of anisotropic rectangular thin plates in free vibration, a general analytical solution is established. This general solution, composed of the composite solutions of trigonometric function and hyperbolic function, can satisfy the problem of arbitrary boundary conditions along four edges. The algebraic polynomial with double sine series solutions can also satisfy the problem of boundary conditions at four corners. Consequently, this general solution can be used to solve the vibration problem of anisotropic rectangular plates with arbitrary boundaries accurately. The integral constants can be determined by boundary conditions of four edges and four corners. Each natural frequency and vibration mode can be solved by the determinate of coefficient matrix from the homogeneous linear algebraic equations equal to zero. For example, a composite symmetric angle ply laminated plate with four edges clamped has been calculated and discussed.     

考虑地基耦合效应时中厚矩形板的非线性自由振动分析

基于各向同性中厚板理论，考虑板的非线性效应和地基耦合效应．应用Hamilton变分原理，建立了双参数地基上周边自由中厚矩形板的非线性运动控制方程，提出了一组满足问题全部边界条件的试函数。应用伽辽金法和谐波平衡法对方程进行求解。讨论了板的结构参数和地基的物理参数对弹性地基上周边自由中厚矩形板的非线性自由振动特性的影响。     

A free rectangular plate on elastic foundation

In the theory of elastic thin plates, the bending of a rectangular plate on the elastic foundation is also a difficult problem. This paper provides a rigorous solution by the method of superposition. It satisfies the differential equation, the boundary conditions of the edges and the free corners. Thus we are led to a system of infinite simultaneous equations. The problem solved is for a plate with a concentrated load at its center. The reactive forces from the foundation should be made to be in equilibrium with the concentrated force to see whether our calculation is correct or not.     

四角点支承四边自由矩形薄板屈曲问题的新解析解

角点支承矩形薄板的屈曲问题是板壳力学的一类重要课题，控制方程和边界条件的复杂性导致寻求该类问题的解析解十分困难。虽然各类近似/数值方法可用于解决此类难题，但作为基准的精确解析解在公开文献中鲜有报道。本文基于近年来提出的辛叠加方法，解析求解了四角点支承四边自由矩形薄板的屈曲问题。首先将问题拆分为两个子问题，接着利用分离变量与辛本征展开推导出子问题的解析解，最后通过叠加获得原问题的解。由于求解过程从基本控制方程出发，逐步严格推导，无需假定解的形式，因此本文解法是一种理性的解析方法。数值算例给出了不同长宽比和不同面内载荷比情况下，四角点支承四边自由矩形薄板的屈曲载荷和典型屈曲模态，并经有限元方法验证，确认了解析解的正确性。     

ANALYSIS OF SYMMETRIC LAMINATED RECTANGULAR PLATES IN PLANE STRESS

Symmetric laminated plates used usually are anisotropic plates. Based on the fundamental equation for anisotropic rectangular plates in plane stress problem, a general analytical solution is established accurately by method of stress function. Therefore the general formula of stress and displacement in plane is given. The integral constants in general formula can be determined by boundary conditions. This general solution is composed of solutions made by trigonometric function and hyperbolic function, which can satisfy the problem of arbitrary boundary conditions along four edges, and the algebraic polynomial solutions which can satisfy the problem of boundary conditions at four corners. Consequently this general solution can be used to solve the plane stress problem with arbitrary boundary conditions. For example, a symmetric laminated square plate acted with uniform normal load, tangential load and nonuniform normal load on four edges is calculated and analyzed.     

弹性地基上各向异性板的静力分析

根据弹性地基上各向异性矩形板弯曲挠度的微分方程精确的求得了适用于各种载荷的非齐次解和各类齐次解。其中由三角函数和双曲线函数组成的齐次解能满足四个边为任意边界条件的问题;由代数多项式和双正弦级数组成的齐次解能满足四个角为任意边界条件的问题。通过适当选取建立了满足任意边界条件和任意载荷作用的一般解。解中的积分常数完全由边界条件来决定。以四边简支承受均布载荷和局部分布载荷的对称迭层复合材料方板为例进行了计算和分析。其结果与已有文献结果是一致的。由于集中载荷不能求得作用点的弯矩,故在例题中改用局部分布载荷因而求得了最大弯矩。     

Three-dimensional vibration analysis of thick rectangular plates using Chebyshev polynomial and Ritz method

This paper describes a method for free vibration analysis of rectangular plates with any thicknesses, which range from thin, moderately thick to very thick plates. It utilises admissible functions comprising the Chebyshev polynomials multiplied by a boundary function. The analysis is based on a linear, small-strain, three-dimensional elasticity theory. The proposed technique yields very accurate natural frequencies and mode shapes of rectangular plates with arbitrary boundary conditions. A very simple and general programme has been compiled for the purpose. For a plate with geometric symmetry, the vibration modes can be classified into symmetric and antisymmetric ones in that direction. In such a case, the computational cost can be greatly reduced while maintaining the same level of accuracy. Convergence studies and comparison have been carried out taking square plates with four simply-supported edges as examples. It is shown that the present method enables rapid convergence, stable numerical operation and very high computational accuracy. Parametric investigations on the vibration behaviour of rectangular plates with four clamped edges have also been performed in detail, with respect to different thickness-side ratios, aspect ratios and Poisson’s ratios. These results may serve as benchmark solutions for validating approximate two-dimensional theories and new computational techniques in future.     

New analytic solutions for static problems of rectangular thin plates point-supported at three corners

This paper deals with the bending of rectangular thin plates point-supported at three corners using an analytic symplectic superposition method. The problems are of fundamental importance in both civil and mechanical engineering, but there were no accurate analytic solutions reported in the literature. This is attributed to the difficulty in seeking the solutions that satisfy the governing fourth-order partial differential equation with the free boundary conditions at all the edges as well as the support conditions at the corners. In the following, the Hamiltonian system-based equation for plate bending is formulated, and two types of fundamental problems are analytically solved by the symplectic method. The analytic solutions of the plates point-supported at three corners are then obtained by superposition, where the constants are obtained by a set of linear equations. The solution procedure presented in this paper offers a rigorous way to yield analytic solutions of similar problems. Some numerical results, validated by the finite element method, are shown to provide useful benchmarks for comparison and validation of other solution methods.