动载下裂纹应力强度因子计算的数值流形元法

相较于传统有限元,数值流形方法（numerical manifold method, NMM） 的一个显著优点是在处理裂纹问题时网格无需与裂纹重合,这就方便了岩体破坏过程的模拟. 基于包含裂尖增强函数的NMM,采用Newmark 隐式动力学算法进行时间积分,重点研究了动力载荷条件下裂纹动态应力强度因子（dynamic stress intensity factor,DSIF） 的求解方法. 针对典型的线弹性动力裂纹问题,给出了NMM 的数值算例. 结果表明NMM 能够准确计算动载荷条件下裂纹的DSIF,并且具有较好的收敛性.      

Dynamic fracture analysis of adhesive bonded material under normal loading

Dynamic fracture behavior of a Griffith crack along the interface of an adhesive bonded material under normal loading is studied. The singular integral equations are obtained by employing integral transformation and introducing dislocation density functions. By adopting Gauss-Jacobi integration formula, the problem is reduced to the solution of algebraic equations, and by collocation dots method. their solutions can be obtained Based on the parametric discussions presented in the paper, the following conclusions can be drawn： （1） Mode I dynamic stress intensity factor （DSIF） increases with increasing initial crack length and decreasing visco-elastic layer thickness, revealing distinct size effect; （2） The influence of the visco-elastic adhesive relaxation time on the DSIF should not be ignored.     

用裂纹张开位移计算三点弯曲试样的动态应力强度因子

给出了一种由裂纹的动态张开位移计算三点弯曲试样的动态应力强度因子的简单方法。对于两种不同几何尺寸的试样,在三类不同载荷作用下给出了数植算例,并与完全的动态有限元方法的计算结果进行了比较。结果表明:两种方法的计算结果相当一致。最后,还给出了由测定三点弯曲试样的裂纹张开位移确定试样的动态应力强度因子,最终确定材料动态起裂韧性的方法。     

The dynamic stress intensity factor analysis of adhesively bonded material interface crack with damage under shear loading

This paper studies the dynamic stress intensity factor (DSIF) at the interface in an adhesive joint under shear loading. Material damage is considered. By introducing the dislocation density function and using the integral transform, the problem is reduced to algebraic equations and can be solved with the collocation dots method in the Laplace domain. Time response of DSIF is calculated with the inverse Laplace integral transform. The results show that the mode Ⅱ DSIF increases with the shear relaxation parameter, shear module and Poisson ratio, while decreases with the swell relaxation parameter. Damage shielding only occurs at the initial stage of crack propagation. The singular index of crack tip is -0.5 and independent on the material parameters, damage conditions of materials, and time. The oscillatory index is controlled by viscoelastic material parameters.     

THE NMM-BASED EFG METHOD AND SIMULATION OF CRACK PROPAGATION

数值流形方法（numerucal manifold method,NMM）通过引入数学覆盖和物理覆盖两套系统来统一处理连续和非连续问题. 通过用移动最小二乘插值（moving least squares interpolation,MLS）中的节点影响域构造数学覆盖,得到了基于数值流形方法的无网格伽辽金法（element free Galerkin,EFG）. 该方法在保证前处理简单的同时,又能方便处理如裂纹等不连续问题. 建立了适用于小变形和大变形的裂纹扩展计算格式,并通过对曲折裂纹（kinked crack）的处理,在不加密的情况下实现了任意小步长的裂纹扩展,大大提高了在固定网格中模拟裂纹扩展的实用性. 大小变形的结果对比表明,按照不考虑构型变化的小变形计算,结果可能偏于危险.     

压电体中孔边Ⅲ型界面裂纹的动应力强度因子

采用Green函数法研究界面上含圆孔边界径向有限长度裂纹的两半无限压电材料对SH波的散射和裂纹尖端动应力强度因子问题.首先构造出具有半圆型凹陷半空间的位移Green函数和电场Green函数,然后采用裂纹"切割"方法构造孔边裂纹,并根据契合思想和界面上的连接条件建立起求解问题的定解积分方程.最后作为算例,给出了孔边界面裂纹尖端动应力强度因子的计算结果图并进行了讨论.     

Dynamic stress intensity factor of a crack perpendicular to the weak-discontinuous interface in a nonhomogeneous coating–substrate structure

A mechanical model was established for the antiplane dynamic fracture problem of a functionally graded coating–substrate structure with a coating crack perpendicular to the weak-discontinuous interface. The problem was reduced to a Cauchy singular integral equation by the methods of Laplace and Fourier integral transforms. Erdogan’s collocation method and the Laplace numerical inversion proposed by Miller and Guy were used to calculate the dynamic stress intensity factors. Three conclusions were drawn through parametric studies: (a) unlike the conclusion drawn for an interfacial crack, reducing the weak discontinuity of the interface will not necessarily decrease the dynamic stress intensity factor (DSIF) of the coating crack perpendicular to the interface; (b) increasing the stiffness of the substrate when that of the coating is fixed, or decreasing the stiffness of coating when that of the substrate is fixed, will be beneficial for the reduction of the DSIF of a coating crack perpendicular to the interface; and (c) the free surface has a greater influence on the DSIF than the interface does, and the effect of the interface on the DSIF is greater than that of the material stiffness in the crack-tip region.     

基于有限变形理论的数值流形方法研究简

原有数值流形方法通过积累每一时步的小变形而得到结构最终的大变形,然而,当结构发生大变形、大转动时往往产生较大计算误差. 针对该问题,从动量守恒方程以及应力边界条件的积分弱形式出发,引入流形方法的插值函数,建立了基于有限变形理论的数值流形方法. 通过对比改进前后流形方法的计算迭代格式,指出了原有流形方法计算大变形问题时的误差来源. 最后,通过大变形悬臂梁和旋转块体算例对有限变形流形方法进行了验证. 数值结果表明,改进后的流形方法能够很好地处理大变形大转动问题,消除了转动所带来的计算误差,其计算结果与解析解及ABAQUS 软件求得的数值解相吻合.     

Scattering of SH-waves by an interacting interface linear crack and a circular cavity near bimaterial interface

An analytical method is developed for scattering of SH-waves and dynamic stress concentration by an interacting interface crack and a circular cavity near bimaterial interface. A suitable Green‘s function is contructed, which is the fundamental solution of the displacement field for an elastic half space with a circular cavity impacted by an out-plane harmonic line source loading at the horizontal surface. First, the bimaterial media is divided into two parts along the horizontal interface, one is an elastic half space with a circular cavity and the other is a complete half space. Then the problem is solved according to the procedure of combination and by the Green‘s function method. The horizontal surfaces of the two half spaces are loaded with undetermined anti-plane forces in order to satisfy continuity conditions at the linking section, or with some forces to recover cracks by means of crack-division technique. A series of Fredholm integral equations of first kind for determining the unknown forces can be set up through continuity conditions as expressed in terms of the Green‘s function. Moreover, some expressions are given in this paper, such as dynamic stress intensity factor (DSIF) at the tip of the interface crack and dynamic stress concentration factor (DSCF) around the circular cavity edge. Numerical examples are provided to show the influences of the wave numbers, the geometrical location of the interface crack and the circular cavity, and parameter combinations of different media upon DSIF and DSCF.     

岩石双孔爆破过程的流形元法模拟

在流形元基本理论基础上,引入断裂力学的裂纹产生及扩展判据,应用二阶流形元对岩石双孔爆破过程进行了研究,模拟了双孔同时起爆和毫秒延时起爆两种条件下裂纹的产生和扩展、块体的形成以及漏斗形成过程,分析了爆炸载荷作用下岩石的破坏规律以及起爆条件对该过程的影响,验证了流形元法在研究冲击载荷作用下岩石从连续体到不连续体破坏过程的准确性和有效性,为研究类似问题提供一个新的思路和方法。     

爆炸荷载下岩石破坏的数值流形方法模拟

为了更好地利用数值流形方法对动力学问题进行分析,在对原数值流形方法中的动力学问题求解思想进行分析的基础上,采用动力有限元方法中的Newmark法对该算法进行了改进。改进后的数值流形方法与原来相比具有三个明显的优势:（1）当选择合适的参数后,该方法能够保证解的无条件收敛;（2）可以采用比原算法大得多的时间步长;（3）充分考虑了动力学问题中的阻尼效应。最后通过一个算例说明了改进后的数值流形方法能够很好地模拟岩石在冲击载荷作用下破坏的全过程,克服了有限元法不能模拟岩石破坏后块体运动情况的不足。     

Dynamic stress intensity factors of two collinear mode-III cracks perpendicular to and on the two sides of a bi-FGM weak-discontinuous interface

The mechanical model was established for the anti-plane dynamic fracture problem for two collinear cracks on the two sides of and perpendicular to a weak-discontinuous interface between two materials with smoothly graded elastic properties, as opposed to a sharp interface with discontinuously changing elastic properties. The problem was reduced as a system of Cauchy singular integral equations of the first kind by Laplace and Fourier integral transforms. The integral equations were solved by Erdogan's collocation method and the dynamic stress intensity factors in the time domain were obtained through Laplace numerical inversion proposed by Miller and Guy. The influences of geometrical and physical parameters on the dynamic stress intensity factors were illustrated and discussed, based on which some conclusions were drawn: (a) to increase the thickness of the FGM strip on either side of the interface will be beneficial to reducing the DSIF of a crack perpendicular to a bi-FGM interface and embedded at the center of one of the FGM strips; (b) To increase the rigidity of the FGM strip where the crack is located will increase the DSIF. However, when the material in one side of the interface is more rigid, the DSIF of the interface-perpendicular embedded crack in the other side will be reduced; (c) To decrease the weak-discontinuity of a bi-FGM interface will not necessarily reduce the stress intensity factor of a crack perpendicular to it, which is different from the case of interfacial crack; (d) For two collinear cracks with equal half-length, when the distance between the two inner tips is less than about three times of the half-length, the interaction of them is intensified, however, when the distance is greater than this the interaction becomes weak.     

The Analysis of Dynamic Stress Intensity Factor for Semi-Circular Surface Crack Using Time-Domain BEM Formulation

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｔｒａｎｓｉｅｎｔａｎａｌｙｓｉｓｆｏｒ 3＿Ｄｅｌａｓｔｏｄｙｎａｍｉｃｃｒａｃｋｐｒｏｂｌｅｍｓｉｓａｎｉｍｐｏｒｔａｎｔｃｏｎｔｅｎｔｉｎｆｒａｃｔｕｒｅｍｅｃｈａｎｉｃｓ.Ｂｅｃａｕｓｅｏｆｔｈｅｄｉｆｆｉｃｕｌｔｉｅｓｏｆｔｈｅｐｒｏｂｌｅｍｓ,ｔｈｅｃａｌｃｕｌａｔｉｏｎｏｆＤＳＩＦｆｏｒ 3＿Ｄｃｒａｃｋｉｓａｐｒｏｂｌｅｍｕｎｓｏｌｖｅｄｃｏｍｐｌｅｔｅｌｙｕｐｔｏｔｈｅｐｒｅｓｅｎｔ.Ｃｈｅｎ[1]ｆｉｒｓｔｌｙｕｓｅｄｔｈｅｆｉｎｉｔｅｄｉｆｆｅｒｅｎｃｅ…     

折线型裂纹对SH波的动力响应

利用Fourier积分变换方法,得出了无限平面中用裂纹位错密度函数表示的单裂纹散射场．根据无穷积分的性质,把单裂纹的散射场分解为奇异部分和有界部分．利用单裂纹的散射场建立了折线裂纹在SH波作用下的Cauchy型奇异积分方程．根据折线裂纹散射场和所得的积分方程讨论了裂纹在折点处的奇性应力及折点处的奇性应力指数．利用所得的奇性应力定义了折点处的应力强度因子．对所得Cauchy型奇积分方程的数值求解,可得裂纹端点和折点处的动应力强度因子。     

三点弯曲试样动态应力强度因子计算研究

利用Hopkinson压杆对三点弯曲试样进行冲击加载,采集了垂直裂纹面距裂尖2mm和与裂纹面成60°距裂尖5mm处的应变信号。根据裂尖附近测试的应变信号计算试样的动态应力强度因子,并与有限元计算结果进行比较,结果表明由于裂尖有一段疲劳裂纹区,通过裂尖附近应变信号来计算动态应力强度因子时,如果裂尖位置确定不准及粘贴应变片位置不够准确对计算结果将带来很大影响。因此利用应变片法计算动态应力强度因子时,为了获得更准确的计算结果,在实验后应对试件裂纹面进行分析测量,重新确定裂尖位置,必要时需对应变片至裂尖距离进行修正后再计算动态应力强度因子值。     

与两相材料界面接触的裂纹对SH波的散射

利用积分变换方法得出了两相材料中作用简谐集中力时的格林函数．根据所得的格林函数并利用Betti-Rayleigh互易定理得出了与界面接触裂纹的散射波场．裂纹的散射波场可分解为两部分，一部分为奇异的散射场，另一部分为有界的散射场．利用分解后的散射场，可得裂纹在SH波作用下的超奇异积分方程．根据裂纹散射场的奇异部分和Cauchy型奇异积分的性质得出了裂纹和界面接触点处的奇性应力指数和接触点角形域内的奇性应力．利用所得的奇性应力定义了裂纹和界面接触点处的动应力强度因子．对所得超奇异积分方程的数值求解可得裂纹端点和接解点处的应力强度因子。     

黏弹性体界面裂纹的冲击响应

研究两半无限大黏弹性体界面Griffith裂纹在反平面剪切突出载荷下,裂纹尖端动应力强度因子的时间响应,首先,运用积分变换方法将黏弹性混合黑社会问题化成变换域上的对偶积分方程,通过引入裂纹位错密度函数进一步化成Cauchy型奇异积分方程,运用分片连续函数法数值求解奇异积分方程,得到变换域内的动应力强度因子,再用Laplace积分变换数值反演方法,将变换域的解反演到时间域内,最终求得动应力强度因子的时间响应,并对黏弹性参数的影响进行分析。     

弹性波与单侧界裂纹相互作用问题的边界元法

措助边界元法设计了一种迭代修正方法来求解单侧界面裂纹模型与弹性波的相互作用问题,作为对算法的检验,用这种方法我们具体地分析了平面简谐弹性波对一个则界面裂纹的入射,给出了裂纹面的接触形态及应力场。     

A novel method in determination of dynamic fracture toughness under mixed mode I/II impact loading

The objective of this paper is to propose a novel methodology for determining dynamic fracture toughness (DFT) of materials under mixed mode I/II impact loading. Previous experimental investigations on mixed mode fracture have been largely limited to qusi-static conditions, due to difficulties in the generation of mixed mode dynamic loading and the precise control of mode mixity at crack tip, in absence of sophisticated experimental techniques. In this study, a hybrid experimental–numerical approach is employed to measure mixed mode DFT of 40Cr high strength steel, with the aid of the split Hopkinson tension bar (SHTB) apparatus and finite element analysis (FEA). A fixture device and a series of tensile specimens with an inclined center crack are designed for the tests to generate the components of mode I and mode II dynamic stress intensity factors (DSIF). Through the change of the crack inclination angle β (=90°, 60°, 45°, and 30°), the K_II/K_I ratio is successfully controlled in the range from 0 to 1.14. A mixed mode I/II dynamic fracture plane, which can also exhibit the information of crack inclination angle and loading rate at the same time, is obtained based on the experimental results. A safety zone is determined in this plane according to the characteristic line. Through observation of the fracture surfaces, different fracture mechanisms are found for pure mode I and mixed mode fractures.     

Moving interfacial crack between piezoelectric ceramic and elastic layers

An analysis is performed for the problem of a finite Griffith crack moving with constant velocity along the interface of a two-layered strip composed of a piezoelectric ceramic and an elastic layers. The combined out-of-plane mechanical and in-plane electrical loads are applied to the strip. Fourier transforms are used to reduce the problem to a pair of dual integral equations, which is then expressed in terms of a Fredholm integral equation of the second kind. The dynamic stress intensity factor(DSIF) is determined, and numerical results show that DSIF depends on the crack length, the ratio of stiffness and thickness, and the magnitude and direction of electrical loads as well as the crack speed. In case that the crack moves along the interface of piezoelectric and elastic half planes, DSIF is independent of the crack speed.