多段翼型吹气流动分离控制研究

基于雷诺平均Navier-Stokes粘性流动方程,采用数值模拟方法,分析了吹气控制对多段翼型气动性能的影响,阐述了吹气改善多段翼型流动的机理。采用有限体积法对雷诺平均Navier-Stokes方程进行空间离散,时间方向推进采用二阶迎风格式,湍流模型采用SST k-ω模型。结果表明:在多段翼型基础上采取吹气控制可以获得很好的气动增升效果,三段翼型的最大升力系数可达4.98;吹气可改善多段翼型表面流动,减小其流动分离,增加升力;在同样的吹气口几何参数条件下,在一定范围内增大吹气动量系数可以提高多段翼型的升力系数;在多段翼型主翼后段和襟翼同时施加吹气流动控制可以获得更好的效果,升力系数比基本三段翼型(基本构型A)增加30.05%。     

基于数值模拟的有限翼展吹气控制研究

以大攻角下增加升力、减小阻力为目的,采用计算流体力学方法,针对在有限展长的三维机翼模型上进行的局部开口吹气控制进行了数值研究。利用结构网格及相应的非定常流计算方法对吹气流动控制进行了数值仿真,分析了吹气动量系数、吹气位置等参数(重点研究吹气口展向位置)对气动特性的影响。研究表明:应用吹气技术可获得较好的气动特性,且能延迟边界层的分离;当吹气动量系数为0.000216且吹气口位于0.2c～0.205c时,二维模型升力系数增加8.2%,阻力系数减小17.2%;当开口长度是有限三维模型翼展的1/5、吹气动量系数为0.003,并在z为2.1～2.4m处引入吹气控制时,三维模型的升力系数增加22.6%,升阻比增加9.5%;对于本文的三维有限翼展机翼模型,当吹气口位于z为2.1～2.4m时可以获得最好的控制效果。     

跨音速翼型和机翼的气动优化设计

以NACA0012翼型和ONERA－M6机翼为基准,分别把可变误差多面体法（VEP）和遗传算法（GA）两种不同的优化方法与求解二维和三维欧拉方程的气动分析相结合,进行跨音速翼型和机翼的气动优化设计,并在其基础上对两种不同性质的优化方法在气动优化设计应用中的优化质量和计算效率进行比较,在优化设计的过程中,翼型通过解析函数线性叠加法来表示,机翼通过不变的翼型和可变的平面形状来表示,二维和三维欧拉方程采用Jamenson提出的有限体积方案,显式四步RungeKutta时间推进求解。     

可渗透壁对翼型声涡相互作用下流场及声场的影响

由仿生学原理构建的可渗透翼型对湍流气动噪声抑制作用已展现良好的应用前景。对NACA 0012可渗透翼型和实体翼型进行了数值计算，得到了声涡相互作用下气动噪声声场和流场，分析了可渗透壁对翼型流场和声场的影响。研究表明，相对实体翼型，可渗透壁通过减小声源强度降低了主纯音噪声声压级幅值和远场总声压级，消除了高阶离散纯音，但对噪声的指向性没有较大改变。进一步的流场分析表明，可渗透壁对翼型气动性能影响不大的情况下能够降低边界层扰动和翼型后缘大尺度涡旋强度，并推迟分离泡转捩和再附位置。     

融入压力分布信息的气动力建模方法

气动外形优化设计与飞行器性能分析中, 直接运用数值模拟或风洞实验获取气动力的成本高, 构建代理模型是提高外形优化和性能分析效率的重要途径. 然而, 构建模型的过程中, 研究者只关注积分后的气动力和力矩信息. 本文通过充分利用采样过程中所产生的压力分布信息, 来提高建模的精度和泛化性, 进而降低样本获取的成本. 提出了一种小样本框架下融入压力分布信息的气动力建模方法, 首先通过数值模拟或风洞试验获得不同流动参数状态下翼型表面的压力分布信息和气动系数, 其次通过本征正交分解技术对压力分布信息进行特征提取, 获取不同输入参数状态下压力分布信息对应的POD系数, 之后结合输入参数通过Kriging算法对压力分布信息进行建模, 将压力分布信息积分得到低精度气动系数的预测模型, 最后低精度气动系数结合输入参数通过Kriging算法构造高精度的气动系数预测模型. 通过同状态变翼型算例以及CAS350翼型变状态算例进行验证, 该方法相比于传统的克里金模型直接预测气动力, 有效提高了气动力的预测精度和模型的鲁棒性, 同时缩小了学习样本的数据量.      

褶皱幅度对仿生翼型滑翔气动特性的影响

蜻蜓翅膀具有独特的褶皱状形貌．研究者们致力于利用仿生学原理,设计在低雷诺数条件下具有更优气动性能的褶皱翼型．本文采用计算流体力学方法,求解二维不可压Navier-Stokes方程组,探讨了四种翼型（平板翼型、流线翼型、小幅度褶皱翼型和大幅度褶皱翼型）的气动表现．在低雷诺数条件下得到以下结果：(1) 较小幅度的褶皱结构有利于增加升力和减小阻力．(2) 雷诺数变化时褶皱翼型的升力系数呈非线性变化;在特定雷诺数区间,幅度相近的褶皱翼型会发生相对气动优势的转变．(3) 褶皱结构内的回流区通过减小粘性阻力,使得翼型总阻力下降．(4) 翼型前缘的极小区域会产生脉冲高升力,对升力表现产生较大影响．这些结果表明,调整褶皱幅度是实现褶皱翼型气动优化的有效方案．     

排翼布局飞行器气动性能的实验研究

通过低速低湍流度风洞实验,研究了利用排翼布局改善充气飞机采用大厚度翼型机翼带来的气动效率偏低问题。首先比较了采用不同厚度翼型的单翼与排式双翼布局的气动特性。在此基础上,为了优化排翼布局的气动特性,研究了给后翼安装偏转角对排翼布局气动特性的影响。同时,基于NACA0030翼型,设计了波纹型外形的充气机翼,比较了此外形下单翼和排翼布局气动性能的差异。实验结果表明,采用排翼布局能够改善采用厚翼型单翼布局的气动性能,而给后翼安装一定偏转角可以进一步提高排翼布局的升力和升阻比。采用波纹外形和光滑外形机翼模型的对比结果表明,波纹外形能够在大迎角时改善充气机翼的失速性能。分析认为,造成这一现象的流动机理是由于波纹型机翼在实验条件下提前由层流转捩为湍流,使失速推迟,流动分离现象有所减弱。     

基于气动特性翼型参数化方法的适用性研究

翼型的优化设计在飞机的研发生产过程中占据相当重要的地位,因为翼型的几何外形会直接影响到飞机的整体气动性能．合理选择恰当的翼型表达方式是翼型优化设计成功的关键之一,其中,参数化方法在近年来得到了广泛应用．针对翼型参数化方法,提出“几何鲁棒性”和“性能鲁棒性”作为评判方法优劣的重要参考标准．选取三种常用的翼型参数化方法--NURBS、CST和PARSEC方法,七种不同类型的翼型,采用四项指标作为系统的评判准则来研究各方法的拟合精度与多点扰动下的几何鲁棒性,并利用Foil Design软件计算气动性能的相关数据,研究各方法在多点扰动下的性能鲁棒性．经对比分析,这三种参数化方法对大部分翼型均具有良好的表达能力,且不同程度地体现了一定的几何鲁棒性与性能鲁棒性．     

基于人工神经网络的机翼外形预测

研究目的是根据机翼各项气动参数,快速准确地预测出符合气动条件的机翼外形.用PARSEC方法对剖面翼型进行参数化处理,得到表征其物理特性的外形参数;用守恒型全速势方程进行流场计算;建立包含214组机翼几何及气动特性的专家数据库.人工神经网络方法对数据库进行分类,训练和测试.先用SOM(Self-Organizing Map)神经网络按气动参数对数据进行分类,再分别用BP(Back Propagation)神经网络,RBF(Radial Basis Function)神经网络和GRNN(General regression Neural Net)进行训练和测试.机翼由6个翼剖面组成,每个翼剖面包含11个PARSEC特征参量,扭转角以及相对厚度,总共78个独立的外形参数.预测值和预期值的相关性分析以及误差分析表明,GRNN的预测结果相比于BP和RBF更为准确;在预测模型的升阻比的平均相对误差的绝对值时,BP的相对误差为2.37%,RBF是0.97%,GRNN是0.40%.     

飞行器的升力、阻力及升力与环量定理的起源

本文介绍了空气动力学中几个基本概念与定律的起源。其中,升力与阻力分别是空气对物体作用力的两个方向上的分量,它们均是由空气与物体的相对运动而产生的,并与该运动速度的平方成正比。库塔儒可夫斯基升力环量定理给出了翼型升力与翼型绕流之间的关系,开启了20世纪早期各国对翼型性能的研究。同时,鉴于理想流体圆柱绕流无阻力的理论结果与实验观察存在的矛盾开始激发人们对黏性流体运动的研究兴趣,并由此诞生了纳维斯托克斯方程组。而后普朗特提出边界层概念,巧妙解决了局部流动与整体流动的关系问题。针对大展弦比直机翼,普朗特又提出了基于升力线假设的升力线模型,并根据翼型气动数据得到三维机翼的气动性能。     

N-S方程数值研究翼型对微型扑翼气动特性的影响

首先基于嵌套网格发展了一套适用于三维扑翼研究的非定常雷诺平均Navier-Stokes(RANS)方程数值模拟方法.为了解决微型扑翼在低马赫数下的收敛问题,使用了预处理方法,湍流模型为BL模型.在该方法的基础上,保持状态参数和扑翼表面形状一定的情况下,分别研究了一系列不同厚度、不同弯度的翼型对于微型扑翼气动特性的影响....     

Numerical evaluation of the aerodynamic influence of the helicopter composite blade trailing edge tabs

In classical composite helicopter rotor blade production, a small flat tab must be formed along the entire trailing edge, in order to enable proper merging of the upper and the lower surface plies during manufacturing. By this, the original airfoil shape is altered. Such fixed tabs have been added in a range of possible angular positions to several existing asymmetrical helicopter airfoils, and their capability to change the moment coefficient about the aerodynamic center of the airfoils was initially analyzed. Although usual tabs are proportionally small, angular domains in which they do not remarkably change the required nearly zero aerodynamic moment, were quantified as very narrow. In the next stage, an algorithm has been defined and implemented: (a) for the determination of optimum angular tab positions for several asymmetrical airfoils, that satisfy the moment requirement (for such airfoils optimum tab direction cannot be known in advance), and (b) for the reduction of the influence of eventual inherent numerical errors of applied software to a minimum. The accuracy of this algorithm has been verified on a symmetrical airfoil, for which the optimum tab position is readily known. In the next step, the tab influence on other aerodynamic airfoil characteristics, and the influence on flight performance of a light helicopter from an on-going project, has been analyzed. Several possible tab design concepts were defined, and some characteristic aspects of their implementation were considered. At the level of preliminary helicopter performance calculations, the influence of the two general outcomes of the tab designs were analyzed, one that preserves initial relative airfoil thickness, and another which leads to its reduction. In the first case, the influence of the slight increase of drag coefficient was taken into account, while in the second one, the decrease of drag coefficient, accompanied with necessary additional strengthening and added blade mass was considered. In both cases applied modifications proved to have moderate direct influence on helicopter flight performance, compared with a hypothetic case that the original airfoil without tab could have been used instead. General conclusions have imposed the need for very careful approach in tab design for asymmetrical airfoils, which must be primarily focused on the tab’s potential remarkable influence on the aerodynamic moment.     

A new direct design method for the medium thickness wind turbine airfoil

The newly developed integral function of airfoil profiles based on Trajkovski conformal transform theory could be used to optimize the profiles for the thin thickness airfoil. However, it is hard to adjust the coefficients of the integral function for the medium thickness airfoil. B-spline curve has an advantage of local adjustment, which makes it to effectively control the airfoil profiles at the trailing edge. Therefore, a new direct design method for the medium thickness wind turbine airfoil based on airfoil integral expression and B-spline curve is presented in this paper. An optimal mathematical model of an airfoil is built. Two new airfoils with similar thickness, based on the new designed method and the original integral method, are designed. According to the comparative analysis, the CQU-A25 airfoil designed based on the new method exhibits better results than that of the CQU-I25 airfoil which is designed based on the original method. It is demonstrated that the new method is feasible to design wind turbine airfoils. Meanwhile, the comparison of the aerodynamic performance for the CQU-A25 airfoil and for the DU91-W2-250 airfoil is studied. Results show that the maximum lift coefficient and the maximum lift/drag ratio of the CQU-A25 airfoil are higher than the ones of DU91-W2-250 airfoil in the same condition. This new airfoil design method would make it possible to design other airfoils with different thicknesses.     

Numerical analysis of active chordwise flexibility on the performance of non-symmetrical flapping airfoils

This paper investigates the effect of active chordwise flexing on the lift, thrust and propulsive efficiency of three types of airfoils. The factors studied are the flexing center location, standard two-sided flexing as well as a type of single-sided flexing. The airfoils are simulated to flap with four configurations, and the effects of flexing under these configurations are investigated. Results show that flexing is not necessarily beneficial for the performance of the airfoils. However, with the correct parameters, efficiency is as high as 0.76 by placing the flexing centre at the trailing edge. The average thrust coefficient is more than twice as high, from 1.63 to 3.57 with flapping and flexing under the right conditions. Moreover, the single-sided flexing also gives an average lift coefficient as high as 4.61 for the S1020 airfoil. The shape of the airfoil does alter the effect of flexing too. Deviating the flexing phase angle away from 90° does not give a significant improvement to the airfoil’s performance. These results greatly enhance the design of a better performing ornithopter wing.     

钝后缘风力机翼型的环量控制研究

钝后缘风力机翼型具有结构强度高、对表面污染不敏感等优点,但其较大的阻力系数使得翼型的整体气动特性不够理想. 利用环量控制方法对钝后缘风力机翼型进行了流动控制,以改善钝后缘风力机翼型的气动特性,减弱尾迹区脱体涡强度. 通过对钝后缘风力机翼型环量控制方法进行相关的数值模拟,对比研究了环量控制方法的增升减阻效果, 研究了环量控制下翼型升阻力特性随射流动量系数的变化规律,并对不同射流动量系数下环量控制方法的气动品质因子和控制效率进行了分析. 研究结果表明:环量控制方法能够大幅提升钝后缘风力机翼型的升力系数,同时有效地降低翼型的阻力系数; 翼型的升力系数随射流动量系数的增大而增大,表现出很明显的分离控制阶段和超环量控制阶段的变化规律; 射流能耗的功率系数随射流动量系数的增大而增大,且增长速率逐渐增大;实施环量控制方法后叶片的输出功率同样随射流动量系数增大而增大,但增长速率逐渐降低. 总体来说,环量控制方法可以有效地改善钝后缘风力机翼型的气动特性以及功率输出特性,在大型风力机流动控制中具有很好的应用前景.      

Analysis of non-symmetrical flapping airfoils

Simulations have been done to assess the lift, thrust and propulsive efficiency of different types of non-symmetrical airfoils under different flapping configurations. The variables involved are reduced frequency, Strouhal number, pitch amplitude and phase angle. In order to analyze the variables more efficiently, the design of experiments using the response surface methodology is applied. Results show that both the variables and shape of the airfoil have a profound effect on the lift, thrust, and efficiency. By using non- symmetrical airfoils, average lift coefficient as high as 2.23 can be obtained. The average thrust coefficient and efficiency also reach high values of 2.53 and 0.61, respectively. The lift production is highly dependent on the airfoil＇s shape while thrust production is influenced more heavily by the variables. Efficiency falls somewhere in between. Two-factor interac- tions are found to exist among the variables. This shows that it is not sufficient to analyze each variable individually. Vorticity diagrams are analyzed to explain the results obtained. Overall, the S1020 airfoil is able to provide relatively good efficiency and at the same time generate high thrust and lift force. These results aid in the design of a better ornithopter＇s wing.     

Effect of one-sided unsteady energy supply on aerodynamic characteristics of airfoils in a transonic flow

The possibility of controlling the aerodynamic characteristics of airfoils in transonic flight regimes by means of one-sided pulsed-periodic energy supply is studied. Based on the numerical solution of two-dimensional unsteady gas-dynamic equations, the change in the flow structure in the vicinity of a symmetric airfoil at different angles of attack and the aerodynamic characteristics of the airfoil as functions of the amount of energy supplied asymmetrically (with respect to the airfoil) are determined. The results obtained are compared with the data calculated for the flow past the airfoil at different angles of attack without energy supply. It is found that a given lift force can be obtained with the use of energy supply at a much better lift-to-drag ratio of the airfoil, as compared to the case of the flow past the airfoil at an angle of attack. The moment characteristics of the airfoil are found. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 49, No. 6, pp. 82–87, November–December, 2008.     

低雷诺数下柔性翼型气动性能分析

基于流固耦合方法对吸力面5%至95%弦长处为三段柔性结构的NACA0012翼型绕流进行了数值模拟,研究了不同弹性模量下柔性翼型的气动性能和结构响应.结果表明:在大攻角下,翼面变形影响着翼型表面的非定常流场,起到延缓失速和提高升力的作用;失速后柔性翼的升力系数下降得较为缓慢,且柔性越大,升力系数下降得越平缓;适当减小弹性模量能够提高翼型的气动性能,然而弹性模量过小反而不利于翼型气动性能的提升,并且翼面会产生大幅度的振动.     

Effect of asymmetric pulsed periodic energy supply on aerodynamic characteristics of airfoils

The possibility of controlling the aerodynamic characteristics of airfoils in transonic flight regimes by means of local pulsed periodic energy supply is considered. The numerical solution of two-dimensional unsteady equations of gas dynamics allowed determining the changes in the flow structure near a symmetric airfoil and its aerodynamic characteristics depending on the magnitude of energy in the case of its asymmetric (with respect to the airfoil) supply. The results obtained are compared with the calculated data for the flow around the airfoil at different angles of attack without energy supply. With the use of energy supply, a prescribed lift force can be obtained with a substantially lower wave drag of the airfoil, as compared with the flow around the airfoil at an angle of attack. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 6, pp. 70–76, November–December, 2007.