钝后缘风力机翼型的环量控制研究

钝后缘风力机翼型具有结构强度高、对表面污染不敏感等优点,但其较大的阻力系数使得翼型的整体气动特性不够理想. 利用环量控制方法对钝后缘风力机翼型进行了流动控制,以改善钝后缘风力机翼型的气动特性,减弱尾迹区脱体涡强度. 通过对钝后缘风力机翼型环量控制方法进行相关的数值模拟,对比研究了环量控制方法的增升减阻效果, 研究了环量控制下翼型升阻力特性随射流动量系数的变化规律,并对不同射流动量系数下环量控制方法的气动品质因子和控制效率进行了分析. 研究结果表明:环量控制方法能够大幅提升钝后缘风力机翼型的升力系数,同时有效地降低翼型的阻力系数; 翼型的升力系数随射流动量系数的增大而增大,表现出很明显的分离控制阶段和超环量控制阶段的变化规律; 射流能耗的功率系数随射流动量系数的增大而增大,且增长速率逐渐增大;实施环量控制方法后叶片的输出功率同样随射流动量系数增大而增大,但增长速率逐渐降低. 总体来说,环量控制方法可以有效地改善钝后缘风力机翼型的气动特性以及功率输出特性,在大型风力机流动控制中具有很好的应用前景.      

褶皱幅度对仿生翼型滑翔气动特性的影响

蜻蜓翅膀具有独特的褶皱状形貌．研究者们致力于利用仿生学原理,设计在低雷诺数条件下具有更优气动性能的褶皱翼型．本文采用计算流体力学方法,求解二维不可压Navier-Stokes方程组,探讨了四种翼型（平板翼型、流线翼型、小幅度褶皱翼型和大幅度褶皱翼型）的气动表现．在低雷诺数条件下得到以下结果：(1) 较小幅度的褶皱结构有利于增加升力和减小阻力．(2) 雷诺数变化时褶皱翼型的升力系数呈非线性变化;在特定雷诺数区间,幅度相近的褶皱翼型会发生相对气动优势的转变．(3) 褶皱结构内的回流区通过减小粘性阻力,使得翼型总阻力下降．(4) 翼型前缘的极小区域会产生脉冲高升力,对升力表现产生较大影响．这些结果表明,调整褶皱幅度是实现褶皱翼型气动优化的有效方案．     

两种椭圆翼型高速气动特性实验研究

新概念旋转机翼飞机的主机翼既能高速旋转作为旋翼,又可锁定作为固定翼,所以只能使用特殊的前后对称翼型。针对主机翼翼型的这一特殊要求,对16％相对厚度,相对弯度分别为0％和3％的两种椭圆翼型的高速气动特性进行了风洞实验研究,试验分别在中国空气动力研究发展中心FL-21风洞和荷兰代尔夫特大学TST-27风洞进行,采用表面测压和尾排型阻测量技术。试验结果的对比分析表明,有弯度椭圆翼型的升力和力矩特性优于无弯度椭圆翼型,而阻力特性和最大升阻比劣于无弯度椭圆翼型。试验结果为旋转机翼飞机主机翼翼型的选取提供了参考。     

顺桨风力机塔叶干涉翼型非稳气动力时频特性

由于风力机叶片与塔筒流场相互干涉,实际气动力与理想情况存在较大差异,这种干涉作用造成的气动力差异给叶片与塔筒结构可靠性带来不可忽视的影响.以翼型DU91-W2-250为研究对象,采用瞬态数值分析与本征正交分解方法,考虑叶片和塔筒流场相互干涉作用,分析顺桨工况翼型非稳气动力时频特性及其影响规律,量化不同雷诺数下塔叶相对位置及几何参数对气动力均值、波动幅度和频率的影响程度,通过流场模态能量分布形态分析,揭示流场干涉对气动力的影响机制.结果表明,翼型气动中心至塔筒几何中心的垂直距离、水平距离以及塔筒直径相对于翼型弦长的无量纲参数y*,x*和D*对气动力均有不同程度影响,其中y*对升阻力系数均值影响最大,对频率无明显影响,y*绝对值越大,C_l均值越接近单翼型C_l值,y*绝对值越小升阻力系数波动幅度越大,y*从-12增大到12,升力系数均值最小值为-0.48,最大值为1.16;x*减小和D*增大,反向阻力均值增大,波动幅度增大,波动频率略有下降,当x*小于临界值5时,带塔翼型阻力均值反向;在计算范围内,带塔翼型升力系数均值相对于单翼型升力系数最大偏差为...     

An experimental study of a bio-inspired corrugated airfoil for micro air vehicle applications

An experimental study was conducted to investigate the aerodynamic characteristics of a bio-inspired corrugated airfoil compared with a smooth-surfaced airfoil and a flat plate at the chord Reynolds number of Re _C  = 58,000–125,000 to explore the potential applications of such bio-inspired corrugated airfoils for micro air vehicle designs. In addition to measuring the aerodynamic lift and drag forces acting on the tested airfoils, a digital particle image velocimetry system was used to conduct detailed flowfield measurements to quantify the transient behavior of vortex and turbulent flow structures around the airfoils. The measurement result revealed clearly that the corrugated airfoil has better performance over the smooth-surfaced airfoil and the flat plate in providing higher lift and preventing large-scale flow separation and airfoil stall at low Reynolds numbers (Re _C  < 100,000). While aerodynamic performance of the smooth-surfaced airfoil and the flat plate would vary considerably with the changing of the chord Reynolds numbers, the aerodynamic performance of the corrugated airfoil was found to be almost insensitive to the Reynolds numbers. The detailed flow field measurements were correlated with the aerodynamic force measurement data to elucidate underlying physics to improve our understanding about how and why the corrugation feature found in dragonfly wings holds aerodynamic advantages for low Reynolds number flight applications.     

The application of the gradient-based adjoint multi-point optimization of single and double shock control bumps for transonic airfoils

A shock control bump (SCB) is a flow control method that uses local small deformations in a flexible wing surface to considerably reduce the strength of shock waves and the resulting wave drag in transonic flows. Most of the reported research is devoted to optimization in a single flow condition. Here, we have used a multi-point adjoint optimization scheme to optimize shape and location of the SCB. Practically, this introduces transonic airfoils equipped with the SCB that are simultaneously optimized for different off-design transonic flight conditions. Here, we use this optimization algorithm to enhance and optimize the performance of SCBs in two benchmark airfoils, i.e., RAE-2822 and NACA-64-A010, over a wide range of off-design Mach numbers. All results are compared with the usual single-point optimization. We use numerical simulation of the turbulent viscous flow and a gradient-based adjoint algorithm to find the optimum location and shape of the SCB. We show that the application of SCBs may increase the aerodynamic performance of an RAE-2822 airfoil by 21.9 and by 22.8 % for a NACA-64-A010 airfoil compared to the no-bump design in a particular flight condition. We have also investigated the simultaneous usage of two bumps for the upper and the lower surfaces of the airfoil. This has resulted in a 26.1 % improvement for the RAE-2822 compared to the clean airfoil in one flight condition.     

Investigation of horizontal-axis wind turbine (HAWT) blade threedimensional rotational effect based on field experiments

Field experiments are performed on a two-bladed 33 kW horizontal-axis wind turbine (HAWT). The pressures are measured with 191 pressure sensors positioned around the surfaces of seven spanwise section airfoils on one of the two blades. Three-dimensional (3D) and two-dimensional (2D) numerical simulations are performed, respectively, on the rotor and the seven airfoils of the blade. The results are compared with the experimental results of the pressure distribution on the seven airfoils and the lift coefficients. The 3D rotational effect on the blade aerodynamic characteristics is then studied with a numerical approach. Finally, some conclusions are drawn as follows. From the tip to the root of the blade, the experimental differential pressure of the blade section airfoil increases at first and then decreases gradually. The calculated 3D result of the pressure distribution on the blade surface is closer to that of the experiment than the 2D result. The 3D rotational effect has a significant impact on the blade surface flow and the aerodynamic load, leading to an increase of the differential pressure on the airfoils and their lift coefficient than that with the 2D one because of the stall delay. The influence of the 3D rotational effect on the wind turbine blade especially takes place on the sections with flow separation.     

Effect of Localization of Pulsed Energy Addition on the Wave Drag of an Airfoil in a Transonic Flow

The possibility of controlling the aerodynamic characteristics of airfoils with the help of local pulsed-periodic energy addition into the flow near the airfoil contour at transonic flight regimes is considered. By means of the numerical solution of two-dimensional unsteady equations of gas dynamics, changes in the flow structure and wave drag of a symmetric airfoil due to changes in localization and shape of energy-addition zones are examined. It is shown that the considered method of controlling airfoil characteristics in transonic flow regimes is rather promising. For a zero angle of attack, the greatest decrease in wave drag is obtained with energy addition at the trailing edge of the airfoil.__________Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 5, pp. 60–67, September–October, 2005.     

Effect of asymmetric pulsed periodic energy supply on aerodynamic characteristics of airfoils

The possibility of controlling the aerodynamic characteristics of airfoils in transonic flight regimes by means of local pulsed periodic energy supply is considered. The numerical solution of two-dimensional unsteady equations of gas dynamics allowed determining the changes in the flow structure near a symmetric airfoil and its aerodynamic characteristics depending on the magnitude of energy in the case of its asymmetric (with respect to the airfoil) supply. The results obtained are compared with the calculated data for the flow around the airfoil at different angles of attack without energy supply. With the use of energy supply, a prescribed lift force can be obtained with a substantially lower wave drag of the airfoil, as compared with the flow around the airfoil at an angle of attack. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 6, pp. 70–76, November–December, 2007.     

A new direct design method for the medium thickness wind turbine airfoil

The newly developed integral function of airfoil profiles based on Trajkovski conformal transform theory could be used to optimize the profiles for the thin thickness airfoil. However, it is hard to adjust the coefficients of the integral function for the medium thickness airfoil. B-spline curve has an advantage of local adjustment, which makes it to effectively control the airfoil profiles at the trailing edge. Therefore, a new direct design method for the medium thickness wind turbine airfoil based on airfoil integral expression and B-spline curve is presented in this paper. An optimal mathematical model of an airfoil is built. Two new airfoils with similar thickness, based on the new designed method and the original integral method, are designed. According to the comparative analysis, the CQU-A25 airfoil designed based on the new method exhibits better results than that of the CQU-I25 airfoil which is designed based on the original method. It is demonstrated that the new method is feasible to design wind turbine airfoils. Meanwhile, the comparison of the aerodynamic performance for the CQU-A25 airfoil and for the DU91-W2-250 airfoil is studied. Results show that the maximum lift coefficient and the maximum lift/drag ratio of the CQU-A25 airfoil are higher than the ones of DU91-W2-250 airfoil in the same condition. This new airfoil design method would make it possible to design other airfoils with different thicknesses.     

Effect of one-sided unsteady energy supply on aerodynamic characteristics of airfoils in a transonic flow

The possibility of controlling the aerodynamic characteristics of airfoils in transonic flight regimes by means of one-sided pulsed-periodic energy supply is studied. Based on the numerical solution of two-dimensional unsteady gas-dynamic equations, the change in the flow structure in the vicinity of a symmetric airfoil at different angles of attack and the aerodynamic characteristics of the airfoil as functions of the amount of energy supplied asymmetrically (with respect to the airfoil) are determined. The results obtained are compared with the data calculated for the flow past the airfoil at different angles of attack without energy supply. It is found that a given lift force can be obtained with the use of energy supply at a much better lift-to-drag ratio of the airfoil, as compared to the case of the flow past the airfoil at an angle of attack. The moment characteristics of the airfoil are found. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 49, No. 6, pp. 82–87, November–December, 2008.     

Aerodynamic characteristics of airfoils with energy supply

The possibility of controlling the aerodynamic characteristics of airfoils with the help of one-sided pulsed-periodic energy supply is studied. The change in the flow structure near the airfoil and its aerodynamic characteristics are determined as functions of the magnitude of energy supply and of the energy-supply location by means of the numerical solution of two-dimensional unsteady equations of gas dynamics. It is demonstrated that external energy supply can substantially improve the aerodynamic characteristics of airfoils with a high lift-to-drag ratio. The moment characteristics of the airfoil are found.     

Lift enhancement of airfoil and tip flow control for wind turbine

Two techniques that improve the aerodynamic performance of wind turbine airfoils are described. The airfoil S809, designed specially for wind turbine blades, and the airfoil FX60-100, having a higher lift-drag ratio, are selected to verify the flow control techniques. The flow deflector, fixed at the leading edge, is employed to control the boundary layer separation on the airfoil at a high angle of attack. The multi-island genetic algorithm is used to optimize the parameters of the flow deflector. The results indicate that the flow deflector can suppress the flow separation, delay the stall, and enhance the lift. The characteristics of the blade tip vortex, the wake vortex, and the surface pressure distributions of the blades are analyzed. The vortex diffuser, set up at the blade tip, is employed to control the blade tip vortex. The results show that the vortex diffuser can increase the total pressure coefficient of the core of the vortex, decrease the strength of the blade tip vortex, lower the noise, and improve the efficiency of the blade.     

固定转捩实验中粗糙带破损对翼型气动特性的影响研究

本文以RAE2822翼型前缘7%位置3mm宽的金刚砂粗糙带为例,研究了粗糙带破损对翼型压力分布的影响。实验结果表明：粗糙带破损会引起激波位置小幅移动,而对翼型后缘压力分布影响很小。当Ma=0.5时,粗糙带破损对升力系数的影响很小;在α≥4°以后粗糙带破损对阻力系数和俯仰力矩系数的影响逐渐增大,且破损位置距翼型中心对称面越远,影响越小。当Ma=0.75时,粗糙带破损对升力系数与阻力系数的影响直到α≥4°后开始逐渐增大,并且随着破损位置远离中心对称面而减弱;俯仰力矩系数对粗糙带破损较为敏感,且粗糙带破损的位置距离中心对称面越远、尺寸越小则影响越小。     

翼型多目标气动优化设计方法

将数值优化软件modeFRONTIER同计算流体力学(CFD)软件相结合,对NACA0012翼型的气动性能进行优化.计算采用N-S方程作为主控方程以计算翼型气动性能,分别采用多目标遗传算法(MOGA)和多目标模拟退火算法(MOSA)作为翼型的气动性能优化算法.计算结果表明,优化后的翼型相对于优化前的翼型的气动性能有很大提高(升阻比增幅可达182%).     

蜻蜓滑翔时柔性褶皱前翅气动特性分析

蜻蜓是自然界优秀的飞行家,滑翔是其常见且有效的飞行模式.蜻蜓优异的飞行能力来源于其翅膀的巧妙结构,褶皱是蜻蜓翅膀上最为显著的结构之一,不仅提高了翅膀的刚度,还改变了其气动特性,而飞行过程中柔性翅膀会产生变形是蜻蜓翅膀的另一特性.为揭示蜻蜓在滑翔时,柔性褶皱前翅的变形,探究褶皱和柔性的共同作用对其气动特性的影响,基于逆向工程,依据前人的测量数据和研究成果,通过三维建模软件建立了蜻蜓三维褶皱前翅的计算流体力学(computational fluiddynamics,CFD)模型和计算结构力学(computational structuralmechanics,CSD)模型,并通过模态分析验证了此模型有足够的精度.基于CFD方法和CFD/CSD双向流固耦合计算方法分别对蜻蜓滑翔飞行时刚性和柔性褶皱前翅的气动特性进行了数值模拟,结果表明,柔性褶皱前翅受气动载荷后,翅脉和翅膜产生形变,柔性前翅上下表面压力差相较于刚性前翅减小了,从而其升力和阻力也减小了,而在大攻角时,变形后的前缘脉诱导出比刚性前翅更强的前缘涡.因此在攻角小于10$^\circ$时刚性前翅的气动特性优于柔性前翅,继续增大攻角,柔性前翅的气动特性则优于刚性前翅.前翅受载后气动响应时间短,翅尖的变形最大,仅仅产生了垂直于翅膀所在平面方向上的变形,而没有发生扭转,翼根处受到应力最大,褶皱上凸部分承受蜻蜓滑翔时前翅的主要载荷.      

风力机叶片翼型动态试验技术研究

风力机叶片动态振荡过程往往伴随着俯仰和横摆同时进行, 以前对许多动态问题不清楚的阶段, 工程上不惜以增加叶片重量为代价而采用偏安全的设计, 通常忽略横摆振荡的影响; 大型风力机设计对获取翼型更加全面、准确的动态载荷提出了更高要求, 研究横摆振荡对翼型动态气动特性的影响规律具有重要意义. 本文首次开展翼型横摆振荡动态风洞试验研究, 采用“电子凸轮”技术代替机械凸轮实现了振荡频率和振荡角度的无级变化, 基于设计的电子外触发装置实现了对动态流场的实时测量, 实现了风洞来流、模型角位移和动态压力数据的同步采集, 分别开展了翼型静态测压、俯仰/横摆动态测压、粒子图像测速和荧光丝线等试验研究, 试验结果准度较高、规律合理; 分析了动态试验洞壁干扰影响机制. 研究表明, 横摆振荡翼型的气动曲线也存在明显迟滞效应; 随着振荡频率升高, 翼型俯仰和横摆振荡下的气动迟滞性均增强; 翼型俯仰振荡正行程的动态失速涡破裂有所延迟; 洞壁与模型端部交界处的强三维效应对翼型压力分布影响较大; 建立的横摆振荡试验技术可为风力机动态掠效应的研究提供技术支撑.      

前后双扑翼水平距离及相位差对其气动性能的影响

通过在动态网格上求解Navier-Stokes方程,对前后双扑翼的非定常粘性流场进行了数值模拟和气动干扰分析,考察了前后翼不同水平距离和不同相位差对其气动力和气动效率的影响。结果表明,扑动前翼和静止后翼间的气动干扰在各种不同水平距离下都有利于气动特性的改善,但气动干扰的作用随着前后翼水平距离的增大而减弱;前后双翼扑动的相位差是影响气动性能的重要参数,两翼间的气动干扰是否有利则与相位差和水平距离有直接联系。     

Resonant phenomena in a transonic flow around an airfoil with pulsed periodic energy supply

Interaction of a pulsed periodic source of energy with a closing shock wave arising near airfoils in transonic flight is studied. The evolution of the shock-wave structure of the flow around a symmetric airfoil is examined by solving two-dimensional unsteady gas-dynamic equations, and a resonant mechanism of interaction is found, which leads to considerable (by an order of magnitude) reduction of the wave drag of the airfoil.     

On the role of a balancing load in the problem of aerodynamic drag minimization in the supersonic flight regime

The problem of reducing the aerodynamic losses through balancing in the supersonic flight regime is considered. An analysis and a comparison of the drag components due to the aerodynamic surface deformation and the balancing weigh distribution is made with reference to the examples of a zero-thickness airfoil and a three-dimensional configuration of an aircraft with a wing of complicated planform. It is shown that minimum values of the aerodynamic drag are achieved as a result of complex optimization including the dead load mass as a varied parameter.