Tailored side‐chain architecture of benzil voltage stabilizers for enhanced dielectric strength of cross‐linked polyethylene

The synthesis and physico‐chemical properties of seven benzil‐type voltage stabilizers are reported. The benzil core is substituted with alkyl chains of different length that are linked to the benzil core via an ester, ether, or tertiary amine group. All additives can be melt‐processed with low‐density polyethylene (LDPE). Fourier‐transform infrared spectroscopy confirms that benzil compounds are not affected by the LDPE cross‐linking reaction induced by dicumyl peroxide. Moreover, a combination of gel content measurements, thermal analysis, and small‐angle X‐ray scattering indicates that the presence of benzil voltage stabilizers does not significantly alter the microstructure of cross‐linked polyethylene (XLPE). Electrical tree inhibition experiments under high‐voltage alternating current conditions show that all investigated additives substantially enhance the dielectric strength of the insulating material at a concentration of only 10 mmol kg^?1. The highest improvement in dielectric strength, of more than 70% with respect to reference XLPE, is obtained with voltage stabilizers, which carry short (methyl) side chains that are linked to the benzil core via an ester or tertiary amine group. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1047–1054     

Investigation of the surfactant type and concentration effect on the retention factors of glutathione and its analogues by micellar electrokinetic chromatography

In the present study, a micellar electrokinetic chromatographic method was used to determine the retention factors of hydrophilic monomeric and homodimeric forms of glutathione analogues. Ionic‐liquid‐based surfactant, 1‐tetradecyl‐3‐methylimidazolium chloride, as well as cetyltrimethylammonium bromide and phosphate buffer (pH 7.4) were employed in the experiments. Since the studied peptides possess a negative charge under physiological conditions, it is expected that the peptides interact with the oppositely charged 1‐tetradecyl‐3‐methylimidazolium chloride and cetyltrimethylammonium bromide micelles via hydrophobically assisted electrostatic forces. The dependence of the retention factor on the micellar concentration of 1‐tetradecyl‐3‐methylimidazolium chloride and cetyltrimethylammonium bromide is nonlinear and the obtained curves converge to a limiting value. The retention factor values of GSH analogues were in the range of 0.36–2.22 for glutathione analogues and –1.21 to 0.37 for glutathione when 1‐tetradecyl‐3‐methylimidazolium chloride was used. When cetyltrimethylammonium bromide was employed, the retention factor values were in the range of 0.27–2.17 for glutathione analogues and –1.22 to 0.06 for glutathione. If sodium dodecyl sulfate was used, the retention factor values of glutathione analogues with carnosine moiety were in the range of –1.54 to 0.38.     

Micromechanics, macromechanics and constitutive modeling of the elasto-viscoplastic deformation of rubber-toughened glassy polymers

Under certain conditions, such as sufficiently low temperatures, high loading rates and/or highly triaxial stress states, glassy polymers display an unfavorable characteristic—brittleness. A technique used for reducing the brittleness (increasing the fracture toughness) of these materials is rubber toughening. While there is significant qualitative understanding of the mechanical behavior of rubber-toughened polymers, quantitative modeling tools for the large-strain deformation of rubber-toughened glassy polymers are largely lacking.In this paper, we develop a suite of numerical tools to investigate the mechanical behavior of rubber-toughened glassy polymers, with emphasis on rubber-toughened polycarbonate. The rubber particles are modeled as voids in view of their deformation-induced cavitation early during deformation. A three-dimensional micromechanical model of the heterogeneous microstructure is developed to study the effects of initial rubber particle (void) volume fraction on the underlying elasto-viscoplastic deformation mechanisms in the material, and how these mechanisms influence the macroscopic response of the material. A continuum-level constitutive model is developed for the large-strain elasto-viscoplastic deformation of porous glassy polymers, and it is calibrated against micromechanical modeling results for porous polycarbonate. The constitutive model can be used to study various boundary value problems involving rubber-toughened (porous) glassy polymers. As an example, the case of an axisymmetric notched bar is simulated for the case of polycarbonate with varying levels of initial porosity. The quality of the constitutive model calibration is assessed using a multi-scale modeling approach.     

Dynamic load and inflation pressure effects on contact pressures of a forestry forwarder tire

A Trelleborg Twin 421 Mark II 600/55-26.5 steel-reinforced bias-ply forwarder drive tire at inflation pressures of 100 and 240 kPa and dynamic loads of 23.9 and 40 kN was used at 5% travel reduction on a firm clay soil. Effects of dynamic load and inflation pressure on soil–tire contact pressures were determined using six pressure transducers mounted on the tire tread. Three were mounted on the face of a lug and three at corresponding locations on the undertread. Contact angles increased with decreases in inflation pressure and increases in dynamic load. Contact pressures on a lug at the edge of the tire increased as dynamic load increased. Mean and peak pressures on the undertread generally were less than those on a lug. The peak pressures on a lug occurred forward of the axle in nearly all combinations of dynamic load, inflation pressure, and pressure sensor location, and peak pressures on the undertread occurred to the rear of the axle in most of the combinations. Ratios of the peak contact pressure to the inflation pressure ranged from 0 at the edge of the undertread for three combinations of dynamic load and inflation pressure to 8.39 for the pressure sensor on a lug, near the tire centerline, when the tire was underinflated. At constant dynamic load, net traction and tractive efficiency decreased as inflation pressure increased.     

Rapid Method to Screen Unopened Bottles to Detect Concealed Drugs

A bottle screening method to detect smuggling drugs was developed based on a series of rapid and automated magnetic resonance measurements. Liquid alteration is detected by evaluating chemical and physical properties of the liquid, scanning the bottle with a compact, non-contact magnetic resonance probe. Chemical and molecular diffusion changes are detected by means of the magnetic resonance relaxation time. The inspection device automatically detects the presence of concealed powders dissolved in liquids in a second timescale. The non-ionizing, non-contact method effectively screens bottles, regardless of their shape, size, and color. The proposed system configuration does not require a large magnet generating uniform magnetic fields; rather it inspects the liquid using a compact probe positioned on the wall of the bottle. For a variety of samples tested, the screening does not require detailed information on the expected content of the bottle.     

Flexible active matrix addressed displays manufactured by printing and coating techniques

A flexible electrochromic active matrix addressed display, including 8 × 8 pixels, is demonstrated by using solution processing based on standard printing and coating manufacturing techniques. Each organic electrochromic display (OECD) pixel and its corresponding organic electrochemical transistor (OECT) are located on different sides of the flexible PET substrate. Electronic vias generated through the plastic substrate connects each OECD pixel with one addressing OECT. When comparing this display with actively addressed OECDs with all its components located on the same side, the present approach based on this electronic via substrate provides an enhanced pixel resolution and a relatively more simplified manufacturing process. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Synthesis, crystal structure and magnetic properties of the open framework compound Co3Te2O2(PO4)2(OH)4

The new compound Co₃Te₂O₂(PO₄)₂(OH)₄ was synthesized using hydrothermal techniques. It crystallizes in the monoclinic space group C2/m with the unit cell a=19.4317(10) Å, b=6.0249(3) Å, c=4.7788(2) Å, β=103.139(5)°. The crystal structure is an open framework having chains of edge sharing [Co(1)O₆] octahedra. Other building blocks are [TeO₃(OH)₂], [PO₄] and [Co(₂)O₂(OH)₄] connected mainly via corner sharing. The –OH groups protrude into channels in the structure. The magnetic susceptibility measured from 2 to 300 K shows two broad anomalies at around 21 K and 4 K, respectively. The peak at ∼20 K is ascribed to a two-dimensional antiferromagnetic ordering of linear [Co(1)O₆] chains coupled by interchain interaction via [PO₄] groups in the Co(1) sheets. The second transition at 4 K is ascribed to a second antiferromagnetic ordering of the moments of the Co(2) entities via super–super exchange involving [PO₄] and [TeO₃(OH)₂] groups. This assignment is strongly supported by low-temperature heat capacity measurements indicating an entropy removal within the high-temperature transition of about twice the magnitude of the low-temperature transition.