圆形截面约束阻尼梁整体有限元建模与振动分析

为克服约束阻尼结构在工程应用中存在的由三维有限元建模造成的单元数目巨大的问题,本文提出了圆形实心截面梁附加约束阻尼层横向振动的整体有限元建模方法,并基于此模型,研究了材料的物理属性和几何因子对这类结构的固有频率的影响。通过与三维有限元解法相比较,证明了该方法的可行性与正确性,并给出了该方法的适用范围。     

蜂窝锥壳卫星适配器约束阻尼层振动抑制分析

主要研究在蜂窝锥壳卫星适配器上附加约束阻尼来抑制锥壳传递振动。尽管约束阻尼方面的研究很多，但是大多数都是针对简单的梁或者板结构，而对复杂蜂窝锥壳结构的振动抑制问题研究还很少；为此，通过对蜂窝壳的等效化处理和约束阻尼结构的有限元建模理论分析，建立起卫星一适配器结构在有无附加约束阻尼情况下的有限元模型，进一步通过模态分析和频响分析，得到不同约束阻尼层设计参数对结构振动抑制影响规律。分析结果对于经济有效的设计约束阻尼层和结构减振减重具有较好的参考价值。     

基于任意四边形单元的约束阻尼板的模态分析

约束层阻尼技术目前广泛应用于薄壁结构的减振降噪中,关于约束阻尼板的有限元分析基本采用矩形或三角形单元,但用于模拟不规则形状结构时,会带来形状拟合上的困难或精度上的不足。基于离散Kirchhoff理论和Layer-wise层合板理论,利用Hamilton原理推导了约束阻尼板的任意四边形单元,并在此基础上考虑粘弹性材料本构的频率相关性,给出了约束阻尼结构复特征值问题的迭代求解算法。数值算例对不同形状的约束阻尼板结构进行了模态分析,通过与解析解、实验结果及有限元结果的对比,表明了本文单元的有效性和对不规则形状结构的适用性。     

基于任意四边形单元的约束阻尼板的模态分析

约束层阻尼技术目前广泛应用于薄壁结构的减振降噪中,关于约束阻尼板的有限元分析基本采用矩形或三角形单元,但用于模拟不规则形状结构时,会带来形状拟合上的困难或精度上的不足。基于离散Kirchhoff理论和Layer-wise层合板理论,利用Hamilton原理推导了约束阻尼板的任意四边形单元,并在此基础上考虑粘弹性材料本构的频率相关性,给出了约束阻尼结构复特征值问题的迭代求解算法。数值算例对不同形状的约束阻尼板结构进行了模态分析,通过与解析解、实验结果及有限元结果的对比,表明了本文单元的有效性和对不规则形状结构的适用性。     

航天支架结构的被动振动控制

重点研究了航天支架结构的被动振动控制问题。在约束阻尼层有限元模型理论分析的基础上，对未附加约束阻尼层的支架计算模态和试验模态进行了相关性分析，制定出被动振动控制策略；通过分析附加约束阻层后支架计算模态和试验模态相关性，建立了有效的支架有限元模型，进一步用于各种情况的动态响应计算和分析。计算了实验结果表明，该控制策略取得了很好的减振效果，为同类结构振动控制问题提供了一个良好的模型参考。     

局部约束阻尼开口柱壳的减振分析及优化

为了缩减开口柱壳结构的振动,本文基于Lagrange方程以及Sanders薄壳理论建立了局部约束阻尼开口柱壳的动力学模型,分析了粘弹性单元分段数和厚度、阻尼单元占空比以及约束层敷设角和厚度对结构前三阶模态损耗因子和固有频率的影响,得到了各参数对结构振动特性的影响规律.并以前三阶损耗因子为目标,应用NSGA-Ⅱ遗传算法对...     

基于遗传算法的约束阻尼梁减振优化分析

约束阻尼结构能有效减振, 但会增加结构的质量和体积, 基于此有必要对其 结构进行优化. 本文应用有限元软件ANSYS建立增设支撑层的约束阻尼梁模型, 根据模态应 变能原理提取约束阻尼梁的模态损耗因子, 并建立以阻尼段长度、约束层厚度、支撑层厚度、 阻尼段数目为设计变量的目标函数, 利用MATLAB多目标遗传算法进行优化运算. 计算结果表 明, 优化后的约束阻尼结构能够在引入质量较小情况下有效减小梁振动幅度, 使振动在较短 的时间内衰减.     

可控约束阻尼层板的控制实验研究

对具有可控约束阻尼层的板进行了振动控制实验研究． 以压电片作为作动器,根据测量的结构振动信号,反馈控制约束层的变形,抑制板的振动． 对试验件进行了试验模态分析,讨论了压电片的附加位置;采用比例反馈对试验件进行了控制试验;试验给出了控制效果和压电片面积的关系． 研究结果证明,这种利用粘弹性阻尼抑制结构的高频振动,利用压电材料的逆压电效应控制结构的低频振动的主被动杂交控制方式对薄壁结构的振动抑制效果显著,控制频率范围宽,可靠性高．     

阻尼夹层筋板结构有限元动力分析

在小变形线弹性理论基础上，导出了粘弹性阻尼夹层筋板壳结构的有限元动力方程，构造了壳单元、阻尼夹层壳单元和开口薄壁梁单元。采用这些单元可以很好地模拟具有不连续阻尼夹层处理的筋板壳结构。数值分析采用［３］中提出的两次渐近法。通过一块阻尼加筋板的特征分析和振动测量，证实了所建立的有限元两次渐近法的良好精度和广泛的工程适用性。     

主动约束层阻尼结构振动控制试验研究

基于主动约束层阻尼结构及独立模态振动控制方法,利用压电驱动器/传感器和粘弹性材料与薄板构成的复合层压阻尼结构,在理论研究的基础上,对一悬壁板结构进行了试验研究,给出了部分试验研究结果,分析总结了主动约束层阻尼结构的主要优缺点.     

Time-dependent hydroelastic analysis of cavitating propulsors

A 3-D potential-based boundary element method (BEM) is coupled with a 3-D finite element method (FEM) for the time-dependent hydroelastic analysis of cavitating propulsors. The BEM is applied to evaluate the moving cavity boundaries and fluctuating pressures, as well as the added mass and hydrodynamic damping matrices. The FEM is applied to analyze the dynamic blade deformations and stresses due to pressure fluctuations and centrifugal forces. The added mass and hydrodynamic damping matrices are superimposed onto the structural mass and damping matrices, respectively, to account for the effect of fluid–structure interaction. The problem is solved in the time-domain using an implicit time integration scheme. An overview of the formulation for both the BEM and FEM is presented, as well as the BEM/FEM coupling algorithm. Numerical and experiment validation studies are shown. The effects of fluid–structure interaction on the propeller performance are discussed.     

Analytical solution for squeeze film damping of MEMS perforated circular plates using Green’s function

Squeezed air film between two closely spaced vibrating microstructures is the important source of energy dissipation and has profound effects on the dynamics of microelectromechanical systems (MEMS). Perforations in the design are one of the methods to model these damping effects. The literature reveals that the analytical modeling of squeeze film damping of perforated circular microplates is less explored; however, these microplates are also an imperative part of the numerous MEMS devices. Here, we derive an analytical model of transverse and rocking motions of a perforated circular microplate. A modified Reynolds equation that incorporates compressibility and rarefaction effects is utilized in the analysis. Pressure distribution under the vibrating microplate is derived by using Green’s function and also derived by finite element method (FEM) to visualize the pressure distribution under perforated and non-perforated areas of the microplate. The analytical damping results are validated with previous renowned analytical models and also with the FEM results. The outcomes confirm the potential of the present analytical model to accurately predict the squeeze film damping parameters.     

主动约束层阻尼部分覆盖圆柱壳耦合振动控制

采用分布参数建模,从Ham ilton变分原理出发推导了主动约束层阻尼(ACLD)覆盖圆柱壳耦合振动的运动微分方程和边界条件,并扩展适合一维连续结构分析的基于解析解的谱传递矩阵法(STMM)用于ACLD部分覆盖圆柱壳。通过数值计算,研究了ACLD的长度和位置对固有频率和模态耗散因子的影响。STMM能有效克服有限元法单元数目多、动力学方程阶数高及ACLD长度和位置变化时须重复建模的缺点,以最少的单元数目建立低阶控制方程。典型算例显示了STMM的有效性和精确性。     

Free vibration of circular cylindrical shell with constrained layer damping

Free vibration characteristics of circular cylindrical shell with passive constrained layer damping (PCLD) are presented. Wave propagation approach rather than finite element method, transfer matrix method, and Rayleigh-Ritz method is used to solve the problem of vibration of PCLD circular cylindrical shell under a simply supported boundary condition at two ends. The governing equations of motion for the orthotropic cylindrical shell with PCLD are derived on the base of Sanders’ thin shell theory. Numerical results show that the present method is more effective in comparison with other methods. The effects of the thickness of viscoelastic core and constrained layer, the elastic modulus ratio of orthotropic constrained layer, the complex shear modulus of viscoelastic core on frequency parameter, and the loss factor are discussed.     

INITIALLY TENSIONED ORTHOTROPIC CYLINDRICAL SHELLS CONVEYING FLUID: A VIBRATION ANALYSIS

A linear analysis of the vibratory behaviour of initially tensioned orthotropic circular cylindrical shells conveying a compressible inviscid fluid is presented. The model is based on the three-dimensional nonlinear theory of elasticity and the Eulerian equations. A nonlinear strain–displacement relationship is employed to derive the geometric stiffness matrix due to initial stresses and hydrostatic pressures. Frequency-dependent fluid mass, damping and stiffness matrices associated with inertia, Coriolis and centrifugal forces, respectively, are derived through the fluid–structure coupling condition. The resulting equation governing the vibration of fluid-conveying shells is solved by the finite element method. The free vibration of initially tensioned orthotropic cylindrical shells conveying fluid is investigated; numerical examples are given and discussed.     

捷联惯导系统减振设计

机抖激光陀螺的捷联惯性导航系统结构设计的关键在于惯性测量单元（IMU）的减振设计。文章描述了一种IMU减振系统设计的方法,并在实际应用当中获得良好的效果。IMU减振系统的设计方法主要分为三大内容。首先是对减振系统中减振器的布局方案进行仿真分析,建立减振系统的六自由度振动响应模型,研究减振器布局方案的频谱特性,比较得到减振效果较优的减振器方案。然后针对获得的减振器布局方案,设计IMU结构框架和各向同性的减振器,并采用有限元的方法,对IMU的减振系统进行模态分析,获得IMU减振系统的前20阶模态频率和振型,用有限元仿真分析的方法来验证减振设计。目前这种IMU减振系统的设计方法已应用到某新型捷联惯导系统当中,减少了系统陀螺精度的降低。     

Design of a tuned vibration absorber for a slender hollow cylindrical structure

Abstract

In this paper, details of the design work for a tuned vibration absorber to be used on a hollow cylindrical structure is presented. The vibration problem is of resonant type and the tuned vibration absorber is designed to suppress the displacement vibration response of the free end of the slender hollow structure dominated by the contribution of its lowest transverse vibration modes. The structure is modeled using a commercial finite element software. Finite element model of the structure is verified using experimentally obtained frequency response functions and modal parameters. Effective parameters of the tuned vibration absorber design are then determined based on finite element analysis simulations of the vibration suppression performance of the tuned vibration absorber as it is used on the structure. Details of the tuned vibration absorber design are determined and a prototype is fabricated. Prototype tuned vibration absorber is then characterized experimentally both as a standalone system and also as it is used on the main structure. Vibration reduction performance of the physical prototype of the tuned vibration absorber is also compared with its vibration reduction performance estimated from finite element analysis simulations so that the analysis based design process can be validated.

Communicated by Dumitru Caruntu.     

分级周期梁结构的振动带隙特性优化研究

针对分级周期梁结构,进行了振动带隙特性优化研究,以期提高结构的减振性能。采用谱元法计算分级周期梁的频响曲线,并结合传递矩阵法计算结构的色散关系,将两种方法相结合来研究结构的振动带隙特性。构建带隙占比函数作为优化目标函数,将单胞结构的尺寸作为优化参数进行带隙特性优化。经过优化,使得在研究频段内带隙特性大大提高。通过与有限元法和振动实验相对比,验证了谱元法计算和优化结果的正确性。研究内容对于提高周期结构的振动带隙特性和减振应用提供有益参考。     

大型复杂圆柱壳中高频振动噪声仿真计算方法研究

建立大型复杂圆柱壳中高频振动噪声仿真计算方法,对于解决船舶和飞机等大型复杂结构的辐射噪声预报问题具有重要意义。介绍了完美匹配层流固耦合计算方法,并成功应用于大型复杂双层圆柱壳的水下辐射噪声预报,相对于传统的声学流固耦合有限元和边界元计算方法,使外部流场域模型至少缩小了11/15。探讨了环频率和阻尼对圆柱壳结构振动传递的影响,提出了求解中高频声学问题时大型圆柱壳复杂结构仿真建模处理方法。数值算例表明,发展的PML方法和模型简化方法是合理的,可应用工程问题研究。