Mixed Mode Dynamic Fracture in Particulate Reinforced Functionally Graded Materials

A detailed analytical and experimental investigation is presented to understand the dynamic fracture behavior of functionally graded materials (FGMs) under mode I and mixed mode loading conditions. Crack-tip stress, strain and displacement fields for a mixed mode crack propagating at an angle from the direction of property gradation were obtained through an asymptotic analysis coupled with a displacement potential approach. This was followed by a comprehensive series of experiments to gain further insight into the behavior of propagating cracks in FGMs. Dynamic photoelasticity coupled with high-speed photography was used to obtain crack tip velocities and dynamic stress fields around the propagating cracks. Birefringent coatings were used to conduct the photoelastic study due to the opaqueness of the FGMs. Dynamic fracture experiments were performed using different specimen geometries to develop a dynamic constitutive fracture relationship between the mode I dynamic stress intensity factor (K _ID ) and crack-tip velocity ( ) for FGMs with the crack moving in the direction of increasing fracture toughness. A similar -K _ID relation was also obtained for matrix material (polyester) for comparison purposes. The results obtained show that crack propagation velocities in FGMs were about 80% higher than the polyester matrix. Crack arrest toughness was found to be about 10% lower than the value of local fracture toughness in FGMs.     

An Experimental Study of Mixed Mode Crack Initiation and Growth in Functionally Graded Materials

Quasi-static mixed mode crack initiation and growth in functionally graded materials (FGMs) was studied through fracture experiments on polymer-based FGMs manufactured by selective ultraviolet irradiation poly(ethylene carbon monoxide)—a photo-sensitive copolymer that becomes more brittle and stiffer under ultraviolet irradiation. The objective of the study was to determine whether crack kinking criteria for homogeneous materials, e.g., maximum hoop stress criterion, also hold for FGMs. Single edge notched tension specimens with different spatial variations of Young's modulus, failure stress and failure strain, were tested. Near tip mode mixity was introduced either by inclining the crack to the remote loading direction, as in the case of homogeneous materials, or to the direction of material gradient, or both. A full-field digital image correlation technique was used to measure in real-time the displacement field around the crack tip while it propagated through the graded material, and to extract the fracture parameters of stress intensity factor K _I and K _II , and the T-stress. It was found that the nonsingular T-stress term in the asymptotic expansion for stresses plays a very important role in accurately measuring fracture parameters. It was also found that the maximum tangential stress criterion can be applied to the case of FGMs to predict crack kinking provided that the effect of the T-stress is accounted for and the process zone size is small compared to the intrinsic material gradient length scale. However, for accurate crack path prediction at a length scale comparable to the material gradient, detailed material property information is required. In general, the crack will propagate towards a region that exhibits less fracture toughness, but, unlike the case of homogeneous materials, along a path where K _II is not necessarily equal to zero.     

Analysis of dynamic growth of a tensile crack in an elastic-plastic material

The influence of inertia on the stress and deformation fields near the tip of a crack growing in an elastic-plastic material is studied. The material is characterized by the von Mises yield criterion and J₂ flow theory of plasticity. The crack grows steadily under plane strain conditions in the tensile opening mode. Features of the stress and deformation state at points near the moving crack tip are described for elastic-perfectly plastic response and for several crack propagation speeds. It is found that inertia has a significant effect on the elastic-plastic response of material particles near the crack tip, and that elastic unloading may occur behind the crack tip for higher speeds. The relationship between the applied crack driving force, represented by a remote stress intensity factor, and the crack tip speed is examined on the basis of a critical crack tip opening angle growth criterion. The calculated result is compared with dynamic fracture toughness versus crack speed data for a 4340 steel.     

Effect of temperature on the fracture modes of BHW-35 steel under mode-II loading

Finite element method (FEM) has been used to analyze the stress and strain fields and the stress tri-axial levels around the tip of the crack under mode- II loading. The results show that: under mode- II loading, the direction of the maximum tensile stress and that of the maximum tri-axial levels (R _o ) exist at an angle of –75. 3° from the original crack plane; the maximum shear stress andR _o = 0 exist along the original crack plane.Mode- II loading experiment using BHW-35 steel at different temperatures show that there are two kinds of fracture mode, opening mode (or tensile mode) and sliding mode (or shear mode). A decrease in temperature causes the fracture mode to change from shear mode to tensile mode. For BHW-35 steel, this critical temperature is about –90 C. Actually, under any kind of loading mode (mode I . mode II , mode III or mixed mode), there always exist several kinds of potenital fracture modes (for example, opening mode, sliding mode, tearing mode or mixed mode). The effect of temperature under mode- II loading is actually related to the change of the elastic-plastic properties of the material.     

THE ANALYSES OF THE THREE-DIMENSIONAL STRESS STRUCTURE NEAR THE CRACK TIP OF MODE I CT SPECIMENS IN ELASTICPLASTIC STATE(Ⅰ)—THE ANALYSES OF CONSTRAINT PARAMETERS AND FRACTURE PARAMETERS

In the present paper, three dimensional analyses of some general constraint parameters and fracture parameters near the crack tip. of Mode I CT specimens in two different thicknesses are carried out by employing ADINA program. The results reveal that the constraints along the thickness direction are obviously separated into two parts: the keeping similar high constraint field (Z₁) and rapid reducing constraints one (Z₂). The two fields are experimentally confiremed to correspond to the smooth region and the shear lip on the fracture face respectively. So the three dimensional stress structure of Mode I specimens can be derived through discussing the two fields respectively. The distribution of the Crack Tip Opening Displacement (CTOD) along the thickness direction and the three dimensional distribution of the void growth ratio (V_g) near the crack tip are also obtained. The two fracture parameters are in similar trends along the thickness direction, and both of them can reflect the effect of thickness and that of the loading level to a certain degree.     

Dynamic crack tip fields and dynamic crack propagation characteristics of anisotropic material

Based on mechanics of anisotropic material, the dynamic crack propagation problem of I/II mixed mode crack in an infinite anisotropic body is investigated. Expressions of dynamic stress intensity factors for modes I and II crack are obtained. Components of dynamic stress and dynamic displacements around the crack tip are derived. The strain energy density theory is used to predict the dynamic crack extension angle. The critical strain energy density is determined by the strength parameters of anisotropic materials. The obtained dynamic crack tip fields are unified and applicable to the analysis of the crack tip fields of anisotropic material, orthotropic material and isotropic material under dynamic or static load. The obtained results show Crack propagation characteristics are represented by the mechanical properties of anisotropic material, i.e., crack propagation velocity M and fiber direction α. In particular, the fiber direction α and the crack propagation velocity M give greater influence on the variations of the stress fields and displacement fields. Fracture angle is found to depend not only on the crack propagation but also on the anisotropic character of the material.     

An experimental investigation of crack-path directional stability

Using the criterion that a crack will extend perpendicular to the maximum circumferential stress,σ _θ, we show that the directional stability of crack growth is governed by the location of microcrack initiation ahead of the crack tip. At distances greater than a geometrical radiusr _o, the maximum value ofσ _θ deviates from the position of symmetry. Thus, if we assume that the physical processes involved in fracture lead to crack initiation at a distancer _c ahead of the crack tip, the criterion for directional stability isr _o>r _c. Experimental and theoretical values ofr _o verify that, asr _o becomes small, the crack's directional stability deteriorates. Observing that a lengthwise compressive stress increasesr _o, a center-cracked specimen was developed which allows the application of controlled lengthwise compression independently of the opening-mode load. A detailed photoelastic analysis of the specimen has provided the value ofr _o as a function of the crack length. The value ofr _o is then compared with the expected microcrack initiation distances in ductile fracture. By applying sufficient lengthwise compression, we are able to make the crack grow straight and obtain numerous data points from this specimen which would otherwise be directionally unstable. The results indicate that, as the total lengthwise tensile stress at the crack tip increases, the fracture toughness also increases. Using this information we can then adjustK _Ic for zero lengthwise loading and obtain a geometry independent fracture toughness.     

A method for measuring mode I crack tip constraint under static and dynamic loading conditions

A novel experimental technique for measuring crack tipT-stress, and hence in-plane crack tip constraint, in elastic materials has been developed. The method exploits optimal positioning of stacked strain gage rosette near a mode I crack tip such that the influence of dominant singular strains is negated in order to determineT-stress accurately. The method is demonstrated for quasi-static and low-velocity impact loading conditions and two values of crack length to plate width ratios (a/W). By coupling this new method with the Dally-Sanford single strain gage method for measuring the mode I stress intensity factorK _I , the crack tip biaxiality parameter is also measured experimentally. Complementary small strain, static and dynamic finite element simulations are carried out under plane stress conditions. Time histories ofK _I andT-stress are computed by regression analysis of the displacement and stress fields, respectively. The experimental results are in good agreement with those obtained from numerical simulations. Preliminary data for critical values ofK _I and β for dynamic experiments involving epoxy specimens are reported. Dynamic crack initiation toughness shows an increasing trend as β becomes more negative at higher impact velocities.     

Fracture toughness for CNT specimens from numerically obtained critical CTOD values

Many approaches for estimating mode I fracture toughness (K_IC) using circumferentially notched tensile (CNT) specimen have been demonstrated in the literature. In this paper, an effective approach for estimating fracture toughness from the numerical solution of critical crack tip opening displacement (CTOD) is proposed. An elasto-plastic finite element analysis is used to estimate critical CTOD values for CNT specimens. A number of materials are analysed, and the relationship between K_IC and critical CTOD for CNT specimens is obtained. The proposed relationship is validated by comparing the fracture toughness values obtained from the relationship with those obtained experimentally using CNT specimens. The fracture toughness (K_IC) calculated according to this relationship from numerically obtained critical CTOD is found to be in close agreement with the experimentally obtained fracture toughness for the respective materials.     

Crack growth under plane stress conditions in an elastic perfectly-plastic material

Mode-I crack growth under conditions of generalized plane stress has been investigated. It has been assumed that near the plane of the crack in the loading zone, the simple stress components corresponding to a central fan field maintain validity up to the elastic-plastic boundary. By the use of expansions of the particle velocities in the coordinate y, and by matching of the relevant stress components and particle velocities to the dominant terms of appropriate elastic fields at the elastic-plastic boundary, a complete solution has been obtained for ε_y in the plane of the crack. The solution applies from the propagating crack tip up to the moving elastic-plastic boundary. The strain fields for a self-similar crack nucleating at a point and for steady-state propagation of a crack have been considered as special cases.     

A novel method in determination of dynamic fracture toughness under mixed mode I/II impact loading

The objective of this paper is to propose a novel methodology for determining dynamic fracture toughness (DFT) of materials under mixed mode I/II impact loading. Previous experimental investigations on mixed mode fracture have been largely limited to qusi-static conditions, due to difficulties in the generation of mixed mode dynamic loading and the precise control of mode mixity at crack tip, in absence of sophisticated experimental techniques. In this study, a hybrid experimental–numerical approach is employed to measure mixed mode DFT of 40Cr high strength steel, with the aid of the split Hopkinson tension bar (SHTB) apparatus and finite element analysis (FEA). A fixture device and a series of tensile specimens with an inclined center crack are designed for the tests to generate the components of mode I and mode II dynamic stress intensity factors (DSIF). Through the change of the crack inclination angle β (=90°, 60°, 45°, and 30°), the K_II/K_I ratio is successfully controlled in the range from 0 to 1.14. A mixed mode I/II dynamic fracture plane, which can also exhibit the information of crack inclination angle and loading rate at the same time, is obtained based on the experimental results. A safety zone is determined in this plane according to the characteristic line. Through observation of the fracture surfaces, different fracture mechanisms are found for pure mode I and mixed mode fractures.     

Analyses of steady quasistatic crack growth in plane strain tension in elastic-plastic materials with non-isotropic hardening

Steady state crack propagation problems of elastic-plastic materials in Mode I, plane strain under small scale yielding conditions were investigated with the aid of the finite element method. The elastic-perfectly plastic solution shows that elastic unloading wedges subtended by the crack tip in the plastic wake region do exist and that the stress state around the crack tip is similar to the modified Prandtl fan solution. To demonstrate the effects of a vertex on the yield surface, the small strain version of a phenomenological J₂, corner theory of plasticity (Christoffersen, J. and Hutchinson, J. W. J. Mech. Phys. Solids,27, 465 C 1979) with a power law stress strain relation was used to govern the strain hardening of the material. The results are compared with the conventional J₂ incremental plasticity solution. To take account of Bauschinger like effects caused by the stress history near the crack tip, a simple kinematic hardening rule with a bilinear stress strain relation was also studied. The results are again compared with the smooth yield surface isotropic hardening solution for the same stress strain curve. There appears to be more potential for steady state crack growth in the conventional J₂ incremental plasticity material than in the other two plasticity laws considered here if a crack opening displacement fracture criterion is used. However, a fracture criterion dependent on both stress and strain could lead to a contrary prediction.     

Theoretical development and experimental validation of a thermally dissipative cohesive zone model for dynamic fracture of amorphous polymers

A thermally dissipative cohesive zone model is developed for predicting the temperature increase at the tip of a crack propagating dynamically in a nominally brittle material exhibiting a cohesive-type failure such as crazing. The model assumes that fracture energy supplied to the crack tip region that is in excess of that needed for the creation of new free surfaces during crack advance is converted to heat within the cohesive zone. Bulk dissipation mechanisms, such as plasticity, are not accounted for. Several cohesive traction laws are examined, and the model is then used to make predictions of crack tip heating at various crack propagation speeds in the nominally brittle amorphous polymer PMMA, observed to fail by a crazing-type mechanism. The heating predictions are compared to experimental data where the temperature field surrounding a high speed crack in PMMA was measured. Measurements are made in real time using a multi-point high speed HgCdTe infrared radiation detector array. At the same time as temperature, simultaneous measurement of fracture energy is made by a strain gauge technique, and crack tip speed is monitored through a resistance ladder method. Material strength can be estimated through uniaxial tension tests, thus minimizing the need for parameter fitting in the stress-opening traction law. Excellent agreement between experiments and theory is found for two of the cohesive traction law temperature predictions, but only for the case where a single craze is active during the dynamic fracture of PMMA, i.e. crack tip speed up to approximately 0.2c_R. For higher speed fracture where subsurface damage becomes prominent, the line dissipation model of a cohesive zone is inadequate, and a distributed damage model is needed.     

裂纹尖端张开角准则的稳态裂纹扩展实验研究

ASTM和ISO已发布获得低约束条件下断裂性能和裂纹稳态扩展阻力曲线的标准,标准中采用多种试验方法确定临界裂纹张开角度来表征板材的裂纹稳态扩展。本文采用准静态裂纹扩展试验方法,通过摄像技术测定裂纹尖端张开角(CTOA),验证标准对1mm厚度2024-T3铝合金板稳态裂纹扩展行为的有效性。研究了试样构型、裂纹尺寸和是否疲劳预制裂纹对裂纹稳态扩展过程中CTOA的影响。试验结果表明:裂纹扩展2mm后,距离裂纹尖端1mm处的CTOA趋于一个恒定值6°,这个值与试样构型和裂纹长度无关;同时,不预制疲劳裂纹对CTOA值和试样的最大剩余强度影响较小。     

Crack tip field andJ-integral with strain gradient effect

The mode I plane strain crack tip field with strain gradient effects is presented in this paper based on a simplified strain gradient theory within the framework proposed by Acharya and Bassani. The theory retains the essential structure of the incremental version of the conventionalJ ₂ deformation theory. No higher-order stress is introduced and no extra boundary value conditions beyond the conventional ones are required. The strain gradient effects are considered in the constitutive relation only through the instantaneous tangent modulus. The strain gradient measures are included into the tangent modulus as internal parameters. Therefore the boundary value problem is the same as that in the conventional theory. Two typical crack problems are studied: (a) the crack tip field under the small scale yielding condition induced by a linear elastic mode-IK-field and (b) the complete field for a compact tension specimen. The calculated results clearly show that the stress level near the crack tip with strain gradient effects is considerable higher than that in the classical theory. The singularity of the strain field near the crack tip is nearly equal to the square-root singularity and the singularity of the stress field is slightly greater than it. Consequently, theJ-integral is no longer path independent and increases monotonically as the radius of the calculated circular contour decreases. The project supported by the National Natural Science Foundation of China (19704100 and 10202023) and the Natural Science Foundation of Chinese Academy of Sciences (KJ951-1-20)     

Dynamic mechanical and fracture properties of an infiltrated TiC-1080 steel cermet

The dynamic mechanical and fracture properties of a TiC porous network infiltrated with1080 steel are reported. Following infiltration, the cermet is subjected to various heat treatments that affect essentially the steel matrix. Dynamic compression tests show that the heat treatments increase the fracture strength of the cermet. The quasi-static fracture toughness (K_Ic) is also increased by the heat treatments. The dynamic (initiation) fracture toughness (K_Id) is substantially higher (by about a factor of 3) than its static counterpart. Failure mechanisms consist mainly of cleavage of the TiC and matrix grains, along with minor interfacial decohesion. However, dynamic loading induces substantial damage around the crack tip, consisting essentially of cleavage of TiC grains. Microcrak toughnening is believed to be responsible for the high dynamic toughness of the material. The critical microstructural fracture event is thus identified as the spreading of TiC cleavage microcracks into the neighboring steel grains.     

Crack separation energy-rates for the DBCS model under biaxial modes of loading

A Modified version of the Dugdale-Bilby-Cottrell-Swinden (DBCS) model simulating the effect of plasticity at the tip of a crack in an infinite region was used by kfouri and rice (1978) to calculate the crack separation energy-rate G^Δ corresponding to a finite crack growth step Δa during plane strain mode I crack extension. The loading consisted of a remote uniaxial tension σp applied normally to the plane of the crack. Using Rice's path-independent integral J to characterize the applied load in the crack tip region, and assuming the length R of the crack tip plastic zone to be small compared with the length of the crack, an analytical expression was derived relating the ratios (J/G^Δ) and (2a/R) for small values of (2a/R). The analytical solution was incomplete in itself in that the value assumed in the plastic region of the DBCS model for the normal stress Y acting on the extending crack surfaces was the product of the yield stress in uniaxial tension σ_Y and an unknown parameter C, the value of which depends on the effect of the local hydrostatic stresses in the case of plane strain conditions. The analytical solution was compared with a numerical solution obtained from a plane strain elastic-plastic finite element analysis on a centre-cracked plate (CCP) of material obeying the von Mises yield criterion. The value used for the yield stress was 310 MN/m² and moderate isotropic linear hardening was applied with a tangent modulus of 4830 MN/m². A uniaxial tension σp was applied on the two appropriate sides of the plate. The comparisons showed that the analytical and finite element solutions were mutually consistent and they enabled the value of C to be established at 1.91. In the present paper similar comparisons are made between the analytical solution and the finite element solutions for the CCP of the same material under different biaxial modes of loading. By assuming further that the form of the analytical solution does not depend on the details of the geometry and of the loading at remote boundaries, a comparison has also been made with the results of a finite element analysis on a compact tension specimen (CTS) made of the same material as the CCP. The different values of C obtained in each case are consistent with investigations by other authors on the effect of load biaxiality on crack tip plasticity.     

On the effects of characteristic lengths in bending and torsion on Mode III crack in couple stress elasticity

The problem of a stationary semi-infinite crack in an elastic solid with microstructures subject to remote classical K_III field is investigated in the present work. The material behavior is described by the indeterminate theory of couple stress elasticity developed by Koiter. This constitutive model includes the characteristic lengths in bending and torsion and thus it is able to account for the underlying microstructure of the material as well as for the strong size effects arising at small scales. The stress and displacement fields turn out to be strongly influenced by the ratio between the characteristic lengths. Moreover, the symmetric stress field turns out to be finite at the crack tip, whereas the skew-symmetric stress field displays a strong singularity. Ahead of the crack tip within a zone smaller than the characteristic length in torsion, the total shear stress and reduced tractions occur with the opposite sign with respect to the classical LEFM solution, due to the relative rotation of the microstructural particles currently at the crack tip. The asymptotic fields dominate within this zone, which however has limited physical relevance and becomes vanishing small for a characteristic length in torsion of zero. In this limiting case the full-field solution recovers the classical K_III field with square-root stress singularity. Outside the zone where the total shear stress is negative, the full-field solution exhibits a bounded maximum for the total shear stress ahead of the crack tip, whose magnitude can be adopted as a measure of the critical stress level for crack advancing. The corresponding fracture criterion defines a critical stress intensity factor, which increases with the characteristic length in torsion. Moreover, the occurrence of a sharp crack profile denotes that the crack becomes stiffer with respect to the classical elastic response, thus revealing that the presence of microstructures may shield the crack tip from fracture.     

Characterization of crack tip stresses in plane-strain fracture specimens having weld center crack

Fracture toughness of metals depends strongly on the state of stress near the crack tip. The existing standards (like R-6, SINTAP) are being modified to account for the influence of stress triaxiality in the flaw assessment procedures. These modifications are based on the ability of so-called ‘constraint parameters’ to describe near tip stresses. Crack tip stresses in homogeneous fracture specimens are successfully described in terms of two parameters like J–Q or J–T. For fracture specimens having a weld center crack, strength mismatch ratio between base and weld material and weld width are the additional variables, along with the magnitude of applied loading, type of loading, and geometry of specimen that affect the crack tip stresses. In this work, a novel three-parameter scheme was proposed to estimate the crack tip opening stress accounting for the above-mentioned variables. The first and second parameters represent the crack tip opening stress in a homogeneous fracture specimen under small-scale yielding and are well known. The third parameter accounts for the effect of constraint developed due to weld strength mismatch. It comprises of weld strength mismatch ratio (M, i.e. ratio of yield strength of weld material to that of base material), and a plastic interaction factor (I_p) that scales the size of the plastic zone with the width of the weld material. The plastic interaction factor represents the degree of influence of weld strength mismatch on crack tip constraint for a given mismatch ratio. The proposed scheme was validated with detailed FE analysis using the Modified Boundary Layer formulation.     

Crack arrest in duplex specimens

Dynamic photoelasticity with high-speed photographic recording is employed to study crack arrest and reinitiation in duplex specimens. The starter section of the duplex specimen is fabricated from Homalite 100, a brittle polyester and the arrest section is fabricated from a relatively tough epoxy. The two materials are joined with a tough, high shear-strength adhesive. The crack was observed to arrest abruptly with very short penetration into the adhesive layer. Crack tip decelerations of the order of 4 × 10⁷ g's were estimated. The fracture affected zone of the arrested crack exhibited a diameter of about 0.5 mm. After arrest the stress intensity factor K increases rapidly with time as the kinetic energy in the modified compact tension specimen is converted to strain energy. If K achieves a sufficiently high value, the crack will reinitiate in the adhesive and extend into the arrest section of the duplex specimen. Otherwise, the crack remains at arrest and the K field at the crack tip oscillates.