Neutron polarization analysis on the multiferroic TbMn2O5

Polycrystalline TbMn₂O₅ was prepared by the standard solid-state reaction method and characterized by powder X-ray diffraction and magnetization to assure it is of single phase. Heat capacity measurements on the compound reveal an antiferromagnetic phase transition at 45 K. A broad peak below 6 K in the heat capacity measurements corresponds to the crossover transition of Tb³⁺ ordering. To confirm these magnetic orderings, neutron powder diffractions on TbMn₂O₅ with XYZ neutron polarization analysis were performed at the diffuse neutron scattering (DNS) spectrometer, FRJ-II, by using neutron wavelength of 4.8 Å in the temperature range of 1.8–250 K. Magnetic scattering was separated from nuclear coherent and spin incoherent scattering contributions. Long-range ordered magnetic peaks were observed below 39 K which is consistent with the heat capacity results. The drastic increasing intensities below 6 K indicate the ferromagnetic transition in Tb³⁺ orderings.     

Structure and properties of the one-dimensional cobalt oxide CaCo2O4

We have studied crystal structure and transport properties of the quasi one-dimensional cobalt oxide CaCo₂O₄. The CaCo₂O₄ phase crystallizes in calcium-ferrite type structure, which consists of a corner- and edge-shared CoO₆ octahedron network including one-dimensional double chains. Large thermoelectric power (S  150 μV/K at 390 K) with metallic temperature dependence of S, moderate resistivity (ρ  2.9 × 10⁻¹ Ω cm at 390 K) with carrier localization at low temperature, and normal thermal conductivity (κ  6.3 W/Km at 390 K) were observed. The phonon mean-free path was calculated from the observed data, as a function of temperature. The long phonon mean-free path (l  24 Å at 300 K) implies that the thermal conductivity could be suppressed by impurity scattering of phonons with partial element substitution.     

Scanning tunneling microscopy/spectroscopy on multi-layered cuprate superconductor Ba2Ca5Cu6O12 (O1−x Fx)2

Scanning tunneling microscopy/spectroscopy (STM/STS) measurements on multi-layered cuprate superconductor Ba₂Ca₅Cu₆O₁₂ (O_1−x F_x)₂ are carried out. STM topographies show randomly distributed bright spot structures with a typical spot size of 0.8 nm. These bright spots are occupied about 28% per one unit cell of c-plane, which is comparable to the regular amount of apical oxygen of 20% obtained from element analysis. Tunneling spectra simultaneously show both the small and the large gap structures. These gap sizes at 4.9 K are about Δ 15 meV and 90 meV, respectively. The small gap structure disappears at the temperature close to T_C, while the large gap persists up to 200 K. Therefore, these features correspond to the superconducting gap and pseudogap, respectively. These facts give evidence for some ordered state with large energy scale even in the superconducting state. For the superconducting gap, the ratio of 2Δ/K_BT_C = 4.9 is obtained with T_C = 70 K, which is determined from temperature dependence of the tunneling spectra.     

Effect of the synthesis route on the structural properties and shape of the indium oxide (In2O3) nano-particles

Nano-crystalline indium oxide (In₂O₃) particles have been synthesized by sol–gel and hydro-thermal techniques. A simple hydro-alcoholic solution consisting indium nitrate hydrate and citric acid (in sol–gel method) and 1, 4-butandiol (in hydro-thermal method) have been utilized. The structural properties of indium oxide nano-powders annealed at 450 °C (for both methods) have been characterized by the X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and specific surface area (SSA) analysis. Structural analysis of the samples shows cubic phase in sol–gel and cubic-hexagonal phase mixture in hydro-thermally prepared particles. The nano-particles prepared by sol–gel method have nearly spherical shape, whereas hydro-thermally-made ones display wire- and needle-like shape in addition to the spherical shape. The obtained In₂O₃ nano-particles surface areas were 23.2 and 55.3 in sol–gel and hydro-thermal methods, respectively. The optical direct band gap of In₂O₃ nano-particles were determined to be 4.32 and 4.24 eV for sol–gel and hydro-thermal methods, respectively. These values exhibit 0.5 eV blue shift from that the bulk In₂O₃ (3.75 eV), which is related to the particle size reduction and approaching the quantum confinement limit of nano-particles.     

Dynamics of the collective excitations of the quantum Hall system

Using the non linear optical technique of 3-pulse 4-wave mixing, we study the dynamics of the collective excitations of the quantum Hall system. We excite the system with 100 fs pulses propagating in directions k₁ and k₃ and then probe its time evolution with a delayed pulse k₂. We measure the non-linear optical response from the lowest Landau level along the direction k₁+k₂−k₃. As function of the time delay of pulse k₂, this signal shows striking beats for short time delays (500 fs), followed by a rise (20 ps) and then a decay (100 ps). We identify the microscopic origin of this dynamics by extending the standard theory of ultra fast nonlinear optics to include the effects of the correlations.     

Spectroscopic investigation of arsenate and selenate incorporation into hydroxylapatite

The mechanism(s) of arsenate and selenate incorporation into hydroxylapatite (HAP) using extended X-ray absorption fine structure (EXAFS) spectroscopy was investigated for As- and Se-doped HAP samples with concentrations between 200 and 2500 ppm. EXAFS data on As and Se K-edges have shown similar local coordination environments and are similar to that of P in HAP, suggesting the substitution of arsenate or selenate tetrahedra on the phosphate sites. EXAFS best-fitting for As-doped samples shows that the first shell is fitted with approximately 4 O atoms at 1.68 Å, showing As(V) in tetrahedral coordination, and Se K-edge EXAFS data are characterized by the backscattering contributions an oxygen shell at 1.2 Å in the Fourier transform, which can be fit with 4 O atoms at 1.65 ± 0.01 Å. This is characteristic of Se–O distances in SeO₄ tetrahedron. These findings suggest that arsenate and selenate substitute for phosphate groups with local distortions during the incorporation of these metals into the structure of HAP.     

The effect of relative plasma plume delay on the properties of complex oxide films grown by multi-laser, multi-target combinatorial pulsed laser deposition

We report the effects of relative time delay of plasma plumes on thin garnet crystal films fabricated by dual-beam, combinatorial pulsed laser deposition. Relative plume delay was found to affect both the lattice constant and elemental composition of mixed Gd₃Ga₅O₁₂ (GGG) and Gd₃Sc₂Ga₃O₁₂ (GSGG) films. Further analysis of the plasmas was undertaken using a Langmuir probe, which revealed that for relative plume delays shorter than 200 μs, the second plume travels through a partial vacuum created by the first plume, leading to higher energy ion bombardment of the growing film. The resulting in-plane stresses are consistent with the transition to a higher value of lattice constant normal to the film plane that was observed around this delay value. At delays shorter than 10 μs, plume propagation was found to overlap, leading to scattering of lighter ions from the plume and a change in stoichiometry of the resultant films.     

One-dimensional excitons in inorganic–organic self-organized quantum-wire crystals [NHC(I)=NH]PbI and [CHSC(=NH)NH]PbI

Optical properties of lead-iodide-based one-dimensional perovskite-type crystals [NH₂C(I)=NH₂]₃PbI₅ and [CH₃SC(=NH₂)NH₂]₃PbI₅ have been investigated theoretically and experimentally. The electronic and excitonic structures are studied based on group theoretical consideration and first-principle band calculation. Strong one-dimensional anisotropy of the optical absorption spectra, large Stokes shifts (1.0 eV) and huge exchange energies (70 meV) indicate that the excitons in these crystals are one-dimensional Frenkel excitons.     

High-performance pyroelectric single crystals for uncooled infrared detection applications

Uncooled pyroelectric infrared detectors based on ferroelectric single crystals 0.74Pb(Mg_1/3Nb_2/3)O₃–0.26PbTiO₃ (PMN–0.26PT) were fabricated. The performances of pyroelectric detectors dependence on detector fabrication temperature, absorption layer, and element thickness were compared. The room-temperature voltage responsivity (R_v) of 200 V/W and specific detectivity (D^*) of 10⁸ cm Hz^1/2/W at 12.5 Hz have been achieved. The results reveal that the better pyroelectric response can be expected by controlling temperature below 70 °C during the fabrication of the pyroelectric detectors, selecting absorption layer with high absorption coefficient, and decreasing the thickness of the elements.     

Nucleation, growth and morphology of Co thin films on Ag(1 1 0)

Scanning tunneling microscopy (STM) experiments reveal that Co growth on Ag(1 1 0), at coverages of Co < 1 ML and low substrate temperatures (150 K), involves a concomitant insertion of Co into the top Ag layer and exchange of Ag out onto the surface. At 300 K, coverages of Co > 1 ML gives rise to a 3D nanocluster growth on the surface, with the clusters covered by Ag. Depending slightly on coverage, the clusters have a typical diameter of 3 nm and a height of 0.4 nm. Upon annealing to 500 K, major changes are observed in the morphology of the surface. STM and AES show that there is a reduction of the number of Co islands on the surface, partly due to subsurface Co cluster migration and partly due to sintering into larger clusters.     

Microwave dielectric properties of (1 − x)(Mg0.95Co0.05)TiO3–x(Na0.5La0.5)TiO3 ceramic system

The microstructures and the microwave dielectric properties of the (1 − x)(Mg_0.95Co_0.05)TiO₃–x(Na_0.5La_0.5)TiO₃ ceramic system were investigated. Two-phase system was confirmed by the XRD patterns and the EDX analysis. A co-existed second phase (Mg_0.95Co_0.05)Ti₂O₅ was also detected. The microwave dielectric properties are strongly related to the density and the matrix of the specimen. A new microwave dielectric material 0.88(Mg_0.95Co_0.05)TiO₃–0.12(Na_0.5La_0.5)TiO₃, possessing an excellent combination of dielectric properties: ε_r  22.36, Q × f  110,000 GHz (at 9 GHz), τ_f  2.9 ppm/°C), is proposed as a candidate dielectric for GPS patch antennas.     

Structure and reaction pathways of methyl lactate on Pd(1 1 1)

The adsorption and reaction of methyl lactate (CH₃CH(OH)COOCH₃) is studied in ultrahigh vacuum on a Pd(1 1 1) surface using temperature-programmed desorption (TPD) and reflection–absorption infrared spectroscopy (RAIRS). Methyl lactate reacts at relatively low temperatures (220 K) by O–H bond scission. This intermediate can either react with hydrogen to reform methyl lactate at 280–300 K or undergo β-hydride elimination to form flat-lying methyl pyruvate. This decomposes to form acetyl and methoxy carbonyl species as found previously following methyl pyruvate adsorption on Pd(1 1 1). These species predominantly react to form carbon monoxide, methane and hydrogen.     

Quasi-distributed displacement sensor for structural monitoring using a commercial OTDR

A quasi-distributed displacement sensor for structural monitoring using an optical time domain reflectometer is demonstrated. Four displacement sensing heads are placed along a standard single mode optical fibre in several locations with different intervals. Their configurations introduce power loss through the decrease of their fibre loop radius when displacement is applied. The decrease of the light intensity with displacement variation is reported. Losses of 9 dB for a 120 mm displacement with a sensitivity of 0.027 dB/mm are reported. The quasi-distributed configuration is able to address sensors with 1 m distance resolution between them.     

The order with respect to oxygen and the activation energy for the burning of an anthracitic char in O2 in a fluidised bed, as measured using a rapid analyser for CO and CO2

Measurements of the oxidation of a coal char in a fluidised bed have the advantages that the rates of heat and mass transfer to and from a reacting particle are large and characterised well. However, problems have arisen from a combination of the slow, but typical, response–time (4 s) of the analysers for CO and CO₂ and the slow mixing of gases when filling a fairly large fluidised bed. The resulting time constant for the sampling system was 8 s and comparable to the time for combustion at 900 °C or above. The purpose of this work was to measure the kinetics of oxidation of a char in a smaller fluidised bed (with a shorter mixing time) using an analyser for CO and CO₂ with a response time as low as 0.1 s. The result is that the oxidation of an anthracitic char is now found to be first order in O₂ between 700 and 900 °C; at 900 °C the order previously measured was almost zero. The activation energy is now measured here to be 145 ± 25 kJ/mol, in agreement with some early work.     

Photonic generation of microwave signal using a dual-wavelength single-longitudinal-mode distributed Bragg reflector fiber laser

In this paper, a novel all-optical microwave generation technique based on a dual-wavelength single-longitudinal-mode (SLM) distributed Bragg reflector (DBR) fiber laser is proposed and demonstrated. By exploiting spatial hole burning (SHB) effect, this laser could provide stable dual-wavelength SLM operation with a wavelength separation of 0.088 nm corresponding to the microwave signal at 10.484 GHz with a 3 dB bandwidth of 28 kHz. By appropriately adjusting the pump power, dual-wavelength oscillation could be maintained at different temperatures. We have theoretically analyzed the mechanism for microwave generation of the proposed DBR laser, and the calculated microwave frequency is in good agreement with our experimental results. Furthermore, experimental observation shows both of the laser wavelengths and generated microwave signals have good stability at room temperature.     

Using multiple quantum coherence to increase the N resolution in a three-dimensional TROSY HNCO experiment for accurate PRE and RDC measurements

We present a new version of the 3D TROSY HNCO pulse scheme, referred to as HR-TROSY HNCO, with comparable resolution in the ¹⁵N dimension to a 2D ¹H–¹⁵N HSQC experiment. In the conventional 3D TROSY HNCO, the constant time period (1/2J_NC  32 ms) severely limits the maximum resolution in the ¹⁵N dimension. In the HR-TROSY HNCO experiment presented here, both constant time periods (32 ms each) for coherence forward and backward transfer between ¹⁵N and ¹³C′ are utilized to double the ¹⁵N evolution time. This leads to a dramatic enhancement in peak separation along the ¹⁵N dimension, making the HR-TROSY HNCO an ideal pulse scheme for accurate paramagnetic relaxation enhancement and residual dipolar coupling measurements.     

Dimensional evolution of silicon nanowires synthesized by Au–Si island-catalyzed chemical vapor deposition

This study explores the nucleation and morphological evolution of silicon nanowires (Si-NWs) on Si (0 0 1) and (1 1 1) substrates synthesized using nanoscale Au–Si island-catalyzed rapid thermal chemical vapor deposition. The Au–Si islands are formed by Au thin film (1.2–3.0 nm) deposition at room temperature followed by annealing at 700 °C, which are employed as a liquid-droplet catalysis during the growth of the Si-NWs. The Si-NWs are grown by exposing the substrates with Au–Si islands to a mixture of gasses SiH₄ and H₂. The growth temperatures and the pressures are 500–600 °C and 0.1–1.0 Torr, respectively. We found a critical thickness of the Au film for Si-NWs nucleation at a given growth condition. Also, we observed that the dimensional evolution of the NWs significantly depends on the growth pressure and temperature. The resulting NWs are 30–100 nm in diameter and 0.4–12.0 μm in length. For Si (0 0 1) substrates 80% of the NWs are aligned along the 1 1 1 direction which are 30° and 60° with respect to the substrate surface while for Si (1 1 1) most of the NWs are aligned vertically along the 1 1 1 direction. In particular, we observed that there appears to be two types of NWs; one with a straight and another with a tapered shape. The morphological and dimensional evolution of the Si-NWs is significantly related to atomic diffusion kinetics and energetics in the vapor–liquid–solid processes.     

Modification of photonic properties in porphyrin-infiltrated opal crystals

Structural, optical and magnetic properties of porphyrin-infiltrated opal hybrid structures were investigated. Bulk samples of synthetic opal were grown by sedimentation technique from colloidal solution of SiO₂ spheres of diameter 250 nm. The structure of the samples was examined by atomic force microscopy. The photonic properties of crystals were investigated by optical measurements in transmission and reflection modes. The stop band was observed in the region 510–550 nm. The photonic properties of synthetic opal crystals were modified by infiltration with aqueous basic solution of iron–porphyrin (FeTPPS) of concentration 1.0 mM. In hybrid samples the absorption bands typical of FeTPPS were observed in the vicinity of the opal stop band. Magnetic properties of FeTPPS-infiltrated opal samples have been studied at 5–300 K in magnetic fields up to 5 T. The FeTPPS-infiltrated opal crystals can be considered as the structures perspective for magnetophotonic devices.     

Superconductivity as a Kosterlitz–Thouless transition in the two-dimensional Hubbard model

We investigate a superconducting Kosterlitz–Thouless transition in the two-dimensional (2D) Hubbard model using auxiliary quantum Monte Carlo method for the ground state. The pair susceptibility is computed for both the attractive and repulsive Hubbard model. The numerical results show that the s-wave pair susceptibility scales as χ  L² for the attractive case, in agreement with previous quantum Monte Carlo studies. The scaling χ  L² also holds for the d-wave pair susceptibility for the repulsive Hubbard model if we adjust the band parameter t′.     

The electrodeposition of copper onto UHV-prepared GaAs(0 0 1) surfaces

Synchrotron surface X-ray diffraction has been used to investigate in situ the morphology and epitaxy of monolayer amounts of copper electrodeposited from aqueous electrolyte onto ultra-high vacuum prepared, smooth, Ga- or As-terminated GaAs(0 0 1) surfaces. The fcc lattice of the epitaxial Cu islands is rotated by 5° and tilted by about 9° with respect to the GaAs substrate lattice, leading to eight symmetry equivalent domains of Cu islands terminated by {1 1 1} facets.