不锈钢表面激光熔覆层与喷焊层耐磨性对比研究

本文研究在１Ｃｒ１８Ｎｉ９Ｔｉ基体上采用激光熔覆和离子喷焊二种工艺形成的涂层对耐磨性的影响。使用５ｋＷ横流ＣＯ２激光器对预置在基体上的Ｃｏ基自熔合金粉末进行单道或多道扫描，得到的熔层与等离子焊层对比结果是：激光熔层缺陷率低，成品率高，其结构致密均匀，晶粒细小，成分稀释率更小，对基体热影响小，熔层硬度与强韧性更高。性能试验证明：激光熔层具有更高的抗擦伤磨损和抗冲击滑动高温磨损性能，耐磨性提高了一倍左右。     

光纤布拉格光栅及其应用

近年来新型的紫外激光写入的光纤布拉格光栅元件（ＦＢＧ）以其具有直接写人光纤芯区、插入损耗小、易于全光集成及波长选择性好、传感信息对波长绝对编码等优点,成为国内外光纤技术领域的研究热点。该论文综述了ＦＢＧ制作技术的进展,介绍和比较了各种制作方法的优缺点,对ＦＢＧ在光纤通讯、光纤传感器等方面的应用前景进行了分析和说明,结果表明ＦＢＧ将对整个光纤技术领域产生重要的影响。     

Plunging method for Nd : YAG laser cladding with wire feeding

The effects of wire feeding direction and position, cladding time, and cladding speed on the quality of cladding layer for laser cladding with wire feeding are studied. Experiment results indicate that the wire feeding direction and position are important for wire laser cladding. By adopting the correct wire feeding direction and position, the wire can be plunged into the melt pool and can be melted by the heat of the molten metal. With the increase of cladding speed, the dilution of clad layer can be reduced and the growth of the grain size of heat-affected zone of the base metal can be limited. If proper cladding parameters are used, the clad layers will have a good surface shape, sound metallurgical bonding with base metal, low dilution, and the effect of heating on heat-affected zone metal can be limited. The hardness of the clad layer and heat-affected zone are checked. It indicates that with the increase of cladding speed, the hardness of the clad layer and heat-affected zone increases.     

40Cr钢表面激光熔覆层的磨损性能

 为研究模具钢熔覆层的磨损性能,采用铁基粉在40Cr钢表面进行激光熔覆,以激光熔覆层为上试样,GCr15钢珠为下试样,采用HT－500磨损试验机进行摩擦磨损试验,并与40Cr基体的磨损性能相对比。利用表面形貌仪测量磨痕深度和宽度。研究结果表明：载荷小于250 g时,相同载荷下基体的摩擦系数大。载荷小于300 g时,随磨损时间延长,熔覆层、基体的摩擦系数都随着载荷增加而减小。当载荷为300 g时,基体的摩擦系数在0.563～0.589之间变化,平均值为0.576,且随时间逐渐升高,耐磨性变差;熔覆层的磨擦系数在0.431～0.457之间变化,平均摩擦系数为0.444,磨痕深度和宽度分别是0.65 mm和1.096 μm,且随时间逐渐下降,表现了良好的耐磨性能。当载荷增加到500 g时,平均摩擦系数和磨痕深度比300 g时分别增加了75％和47倍,且摩擦系数逐渐升高,磨损性能下降。     

激光工艺参数对钛合金表面NiCrBSi合金熔覆层组织及硬度的影响

在TC4合金表面进行了激光熔覆NiCrBSi合金涂层的试验 ,利用SEM和XRD等对熔覆层的微观组织进行了分析 ,测试了熔覆层的显微硬度。结果表明 ,激光工艺参数对熔覆层的组织和硬度有极大的影响 ,随稀释率的增加 ,激光熔覆层中形成了TiB2 和TiC等颗粒增强相 ,熔覆层的硬度明显提高。     

Laser cladding of copper with molybdenum for wear resistance enhancement in electrical contacts

Laser cladding of Mo on Cu has been attempted with the aim of enhancing the wear resistance and hence increasing the service life of electrical contacts made of Cu. In order to overcome the difficulties arising from the large difference in thermal properties and the low mutual solubility between Cu and Mo, Ni was introduced as an intermediate layer between Mo and Cu. The Ni and Mo layers were laser clad one after the other to form a sandwich layer of Mo/Ni/Cu. Excellent bonding between the clad layer and the Cu substrate was ensured by strong metallurgical bonding. The hardness of the surface of the clad layer is seven times higher than that of the Cu substrate. Pin-on-disc wear tests consistently showed that the abrasive wear resistance of the clad layer was also improved by a factor of seven as compared with untreated Cu substrate. The specific electrical contact resistance of the clad surface was about 5.6 × 10⁻⁷ Ω cm².     

Reactive plasma cladding of TiC/Fe cermet coating using asphalt as a carbonaceous precursor

A new process of preparing Ti-Fe-C composites powder for reactive plasma cladding, precursor carbonization-composition process, was developed. TiC/Fe cermet coatings were synthesized by reactive plasma cladding of the composite powder. XRD and SEM were employed to analyze the phase composition and microstructure of the composite powder and coating. The hardness and wear resistance of the coating was tested. Results show that: The compound powder prepared by precursor carbonization-composition process has very tight structure, which can avert the question of raw powder breaking-up in cladding process. The TiC/Fe cermet coating by reactive plasma cladding consists of alternate, laminated layers as following: the layers in which the round nanoscale TiC particles are dispersed within the α-Fe matrix and the layers of TiC accumulation. The TiC/Fe cermet coating by reactive plasma cladding shows superior hardness and wear resistance: The surface hardness of the TiC/Fe cermet coating is 68 ± 6 (HR30 N). In the same fretting conditions, the wear resistance of Ni60 coating is twelve times than that of the TiC/Fe cermet coating.     

激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究

采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。     

钛合金表面激光熔覆TiC_p/Ni基合金复合耐磨涂层

采用激光熔覆技术在TC4合金表面制备TiC颗粒增强的Ni基合金复合材料涂层,测试了熔覆层的硬度和滑动摩擦磨损性能,分析了熔覆层的强化机制。结果表明,熔覆层中存在颗粒强化、固溶强化和细晶强化等多种强化作用,熔覆层的显微硬度达HV900～1100,耐磨性能比TC4合金显著提高。     

Prediction of clad angle in laser cladding by powder using response surface methodology and scatter search

Currently, laser cladding is an important process that allows the deposition of thick protective coatings on substrates. The article presents an experimental investigation of the influence of processing parameters on clad angle in laser cladding by powder (LCP). The clad angle is determined from the mathematical expression relating to the clad height and clad width. The cladding angle model was developed in terms of laser power, scanning speed, and powder mass flow rate by means of response surface methodology. A first-order equation covering a narrow range of the variables and a second-order equation covering a wide range of the variables are presented. An optimization technique, Scatter Search, is used to determine optimal processing parameters. The adequacy of the predictive model was tested by analysis of variance and found to be adequate.     

Reciprocating sliding wear behavior of laser-clad small amplitude Mo2Ni3Si/NiSi metal silicide composite coatings

Mo₂Ni₃Si/NiSi metal silicide composite coatings with a fine microstructure consisting of Mo₂Ni₃Si primary dendrites and the interdendritic Mo₂Ni₃Si/NiSi eutectics were fabricated on austenitic stainless steel AISI 321 by laser cladding process. Small amplitude reciprocating sliding wear resistance of the coatings is evaluated as functions of normal load and slip amplitude and the wear mechanisms were discussed based on worn surface morphology observations. Results showed that the Mo₂Ni₃Si/NiSi coatings have excellent small amplitude reciprocating sliding wear resistance.     

Si,Al对激光熔覆MoFeCrTiW高熵合金涂层组织性能的影响

为了提高材料表面的耐磨性和高温抗氧化性,利用激光熔覆技术在Q235钢表面制备了MoFeCrTiW高熵合金涂层,并采用X射线衍射仪(XRD)、扫描电镜(SEM)和磨损试验机等研究了Si,Al添加对高熵合金涂层组织、相结构、耐磨性和高温抗氧化性能的影响。结果表明:激光熔覆MoFeCrTiW高熵合金涂层组织为等轴晶,单独添加等物质的量的Si或Al时,涂层分别为共晶组织或树枝晶,同时添加等物质的量的Si和Al时,涂层组织为细小的等轴晶。各高熵合金涂层的主体相均为BCC相,随着Si,Al的添加,BCC相的晶格常数减小。添加等物质的量的Al有助于抑制涂层中金属间化合物的形成,使涂层耐磨性降低;添加等物质的量的Si则会形成含Si的金属间化合物和一些未知相,提高涂层耐磨性。激光熔覆MoFeCrTiW高熵合金涂层在800℃的抗氧化性较高,Si、Al的添加可使涂层的高温抗氧化性进一步提高。     

磁场辅助激光熔覆制备Ni60CuMoW复合涂层

采用磁场辅助激光熔覆技术,在Q235钢表面制备了Ni60CuMoW复合涂层,借助SEM,EDS 和XRD 等表征手段对涂层进行了微观组织和物相分析,利用维氏硬度计测试了复合涂层截面的显微硬度分布,通过摩擦磨损实验和电化学测试系统研究了复合涂层的磨损性能和耐腐蚀性能。研究结果表明:涂层主要由-Ni,Cu）固溶体、硅化物和硼化物组成,Cr3Si晶粒细化且均匀致密;磁场辅助作用下,激光熔覆涂层平均显微硬度达到913HV0.5,为无磁场辅助涂层的1.5 倍,磨损失重仅为无磁场涂层的36%,自腐蚀电位上升了100 mV,腐蚀电流密度降低了70%,耐磨耐蚀性能得到了显著改善。     

激光熔覆原位合成Nb(C,N)陶瓷颗粒增强铁基金属涂层

采用预涂粉末激光熔覆技术,在42CrMo基体上制备出原位合成Nb(C, N)颗粒增强的铁基复合涂层。X射线及扫描电镜分析结果表明:激光熔覆获得的涂层基体为耐氧化、耐蚀性良好的Fe-Cr细晶组织及少量的-Fe相,原位合成的Nb（C, N）呈块状弥散分布在基体上。进一步的磨损试验表明:这些颗粒增强相极大增强了抗磨损性能,与未熔覆的母材相比,其磨损失重仅为母材的1/9左右; 涂层在750 ℃恒温氧化条件下具有较好的抗氧化性能,氧化层主要由NbO1.1,Cr2O3相组成; 母材的氧化产物为Fe2O3,容易脱落,保护性能较差; 激光熔覆涂层的氧化膜厚度仅为未涂层的1/5。     

Coaxial laser cladding on an inclined substrate

This paper describes an experimental and theoretical study of the cladding mode of coaxial laser cladding on an inclined substrate. Based on the image analysis of the powder stream and clad profile measurements in coaxial laser cladding, it was found that irregular clad profiles always formed on an inclined surface and the location of the peak profile shifted away from the clad center. This phenomenon is caused by uneven distributions of powder concentration and laser beam intensity. A modified Gaussian mode for powder stream and laser beam was proposed to estimate the clad profiles on an inclined plane under laser beam irradiation. The effects of the inclined steel substrate on the CO₂ laser beam absorption and stainless-steel powder catchment were examined experimentally. The results show that both the laser absorption and the powder catchment on the mild steel decrease with increasing the cladding angle. From the analysis of laser beam mode, the clad width is equivalent to the beam spot size on the inclined substrate. However, the clad height correlates well with the distribution of the powder concentration. The results show that the Gaussian cladding mode could be adopted in various laser cladding applications such as rapid prototyping and butt welding to predict the clad profiles precisely.     

Phase composition and tribological properties of Ti-Al coatings produced on pure Ti by laser cladding

Ti-Al coatings with ∼14.7, 18.1, 25.2 and 29.7 at.% Al contents were fabricated on pure Ti substrate by laser cladding. The laser cladding Ti-Al coatings were analyzed with X-ray diffraction (XRD), scanning electron microscope (SEM) and X-ray energy dispersive spectroscopy (EDS). It was found that with the increase of Al content, the diffraction peaks shifted gradually to higher 2θ values. The laser cladding Ti-Al coatings with 14.7 and 18.1 at.% Al were composed of α-Ti and α₂-Ti₃Al phases, while those with 25.2 and 29.7 at.% Al were composed of α₂-Ti₃Al phase. With the increase of Al content, the cross-sectional hardness increased, while the fracture toughness decreased. For the laser cladding Ti-Al coatings, when the Al content was ≤18.1 at.%, the wear mechanism was adhesive wear and abrasive wear; while when the Al content ≥25.2 at.%, the wear mechanism was adhesive wear, abrasive wear and microfracture. With the increase of Al content, the wear rate of laser cladding Ti-Al coatings decreased under 1 N normal load, while the wear rate firstly decreased and then increased under a normal load of 3 N. Due to its optimized combination of high hardness and high fracture toughness, the laser cladding Ti-Al coating with 18.1 at.% Al showed the best anti-wear properties at higher normal load.     

Investigation of temperature and stress fields in laser cladded coatings

Temporal and spatial distributions of temperature and strain-stress have been modelled and investigated experimentally for the laser cladding process. The model corresponded to experimental conditions where the multilayer protective coatings were prepared by direct laser cladding of stellite SF6 powder on X10Cr13 chromium steel by means of a 1.2 kW CO₂ laser. For calculations the effect of base preheating, temperature dependent material properties, and also influence of time-break between cladding of the consecutive layers were taken into account. The calculated temperature fields indicated good bonding of the substrate and coating, which was in agreement with the micro-analytical test results. A decrease of the number of microcracks in the coating with an increase of substrate preheating temperature was concluded from stress calculations and confirmed in the experiment. Moreover, an increase of the cracking susceptibility with an increase of the time delay between cladding of the consecutive layers was evidenced by modelling. The best technological results were obtained for the case of single-layer coatings prepared on a preheated substrate and for higher coating thickness required the processing of consecutive layers with a possibly short time delay is advisable due to effective usage of laser beam energy for preheating and lower temperature gradients.     

碳化钨对激光熔覆高熵合金的影响

为了获得高性能的涂层材料,采用激光熔覆的方法,在Q235钢基体上制备了FeSiCrCoMo高熵合金涂层,并研究了WC对高熵合金涂层的组织和性能的影响。通过金相、X射线衍射、扫描电镜、硬度计、磨损试验机分别研究了添加WC前后涂层的微观形貌、相结构、硬度及磨损性能。结果表明:高熵合金FeSiCrCoMo涂层组织为粗大枝状晶,主要由BCC相和金属间化合物构成,添加WC后,涂层中形成了致密细小的胞状晶,同时BCC相增多,金属间化合物明显减少;添加WC后涂层的硬度明显增强,平均硬度提升了23%,涂层表面平均硬度达到了687HV0.2;WC的添加使得涂层的摩擦系数减小,磨损率减小,耐磨性能提高。     

铁基合金激光熔覆层高温润滑磨损性能

 为提高40Cr合金钢的表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备铁基合金涂层, 利用扫描电镜观察分析熔覆层显微组织形貌,用显微硬度仪测试熔覆层截面显微硬度,用摩擦磨损试验机测定在润滑条件下基体、熔覆层的摩擦系数随温度变化的规律。研究结果表明:熔覆层与基体实现良好冶金结合,熔覆层横截面微观组织呈现平面晶、树枝晶和胞状晶分布;熔覆层硬度值介于617.5~926.6 HV0.2之间,基体硬度介于205.2~278.2 HV0.2之间;在200 ℃以下,熔覆层摩擦系数在磨程中趋于平稳,在0.1附近轻微波动,小于基体平均摩擦系数;当温度超过200 ℃,油膜分解,引发润滑失效,磨损方式向干摩擦转化,磨损机理从微切削磨损主导向粘着磨损、磨粒磨损和氧化磨损复合磨损方式转化。     

Microstructure and wear properties of laser clad Cuss/Cr5Si3 metal silicide composite coatings

Wear resistant Cu-based solid solution (Cu_ss) toughened Cr₅Si₃ metal silicide composite coatings were fabricated on austenitic stainless steel AISI321 by laser cladding process. Due to the rapidly solidified microstructural characteristics and the excellent toughening effect of Cu_ss on Cr₅Si₃, the Cu_ss/Cr₅Si₃ coatings have outstanding wear resistance and low coefficient of friction under room temperature dry sliding wear test conditions coupling with hardened 0.45% C steel.