Observation of stable bound soliton with dual-wavelength in a passively mode-locked Er-doped fiber laser

A phase-locked bound state soliton with dual-wavelength is observed experimentally in a passively mode-locked Erdoped fiber(EDF) laser with a fiber loop mirror(FLM). The pulse duration of the soliton is 15 ps and the peak-to-peak separation is 125 ps. The repetition rate of the pulse sequence is 3.47 MHz. The output power is 11.8 mW at the pump power of 128 mW, corresponding to the pulse energy of 1.52 nJ. The FLM with a polarization controller can produce a comb spectrum, which acts as a filter. By adjusting the polarization controller or varying the pump power, the central wavelength of the comb spectrum can be tuned. When it combines with the reflective spectrum of the fiber Bragg grating, the total spectrum of the cavity can be cleaved into two parts, then the bound state soliton with dual-wavelength at 1549.7 nm and 1550.4 nm is obtained.     

High-power all-normal-dispersion femtosecond pulse generation from a Yb-doped large-mode-area microstructure fiber laser

We report on an all-normal-dispersion mode-locked fiber laser based on a large-mode-area Yb-doped microstructure fiber and using a high nonlinear modulation depth semiconductor saturable absorber mirror. The laser delivers 3.3 W of average output power with positively chirped 5.5 ps pulses at a center wavelength of 1033 nm. The pulse repetition rate is 46.4 MHz, which results in an energy per pulse of 71 nJ. These pulses are extracavity dechirped down to 516 fs by using bulk gratings. The average power of the dechirped pulses is 2.3 W, which corresponds to a peak power of more than 96 kW.     

High-power passive mode-locking of a diode pumped Yb:GdVO4 laser

Passive mode-locking of a diode pumped Yb-doped GdVO₄ crystal laser was demonstrated for the first time to our knowledge. The laser was mode-locked at the wavelength of 1019.1 nm and had an average output power of 1.01 W. The mode-locked pulse duration was 3.1 ps. The laser was end-pumped by a high-power fiber pigtailed laser diode bar and the mode-locking was enabled by a semiconductor saturable absorber mirror (SESAM).     

全光纤高功率被动锁模掺铥光纤激光器

利用非线性光环形镜(NOLM)的可饱和吸收特性实现了可自启动的2μm全光纤高能量被动锁模掺铥光纤激光器。当泵浦功率大于3W时,激光器工作在连续或不稳定脉冲运转状态;泵浦功率达到4.69W后,输出为自启动锁模脉冲,重复频率4.26MHz,中心波长2 061.5nm,光谱半极大宽度18.1nm,平均输出功率8.8mW;继续增加泵浦功率到最大值7.56W,可以得到中心波长2 062.2nm、光谱半极大宽度17.1nm、斜率效率为6.2%、脉冲宽度和能量分别为424fs和65.6nJ的稳定锁模脉冲。这是目前已报道的在未经放大情况下脉冲能量最高的2μm锁模脉冲光纤激光器。     

基于全保偏八字腔结构锁模的光纤激光器及其功率放大

采用包层泵浦的全保偏八字腔结构搭建了一种脉宽可调的掺镱锁模光纤激光器,实现了中心波长为1 064nm、重复频率为4.683 MHz、脉冲宽度可调范围为0.8~5ns、对应平均功率范围为74.8~429.7mW的耗散孤子共振方波脉冲输出.腔内无需偏振控制器,仅通过调节泵浦输入即可实现锁模状态的自启动,并能够长时间保持稳定,在剧烈振动条件下亦不会失锁.采用两级光纤放大器进行功率放大,实现了100 W的平均功率输出,峰值功率高达26.68kW.     

滤波对8字腔掺铒光纤激光器锁模运转的影响

构建了基于损耗非对称非线性光学环镜的8字腔掺铒光纤锁模激光器,并讨论了腔内滤波带宽对腔内脉冲演化和激光器输出特性的影响.在非线性光学环镜中引入双向输出耦合器,耦合器和传输光纤位置的不对称产生非互易性,实现锁模运转.利用自制的可调谐滤波器实验研究了滤波带宽对激光器的影响.当滤波带宽为2.1 nm时,腔内脉冲的演化过程受滤波和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲半高全宽分别为583.7fs和2.94 ps.随着滤波带宽增大,滤波的作用逐渐减弱,激光器两路输出脉冲参数逐渐接近,并接近傅里叶变换极限脉冲.当滤波带宽较大时,腔内脉冲的演化过程受增益谱和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲均为变换极限脉冲,半高全宽约为440 fs.通过调节滤波器中心波长实现了对激光器输出脉冲光谱的连续调谐,调节范围大于30 nm.     

Self-starting mode-locked picosecond Ti：sapphire laser by using of a fast SESAM

A stable continuous wave mode-locked picosecond Ti:sapphire laser by using a fast semiconductor saturable absorber mirror (SESAM) is demonstrated. The laser delivers pulse width of 20 ps at a central wavelength of 813 nm and a repetition rate of 100 MHz. The maximum output power is 1.34 W with pump power of 7 W which corresponds to an optical--optical conversion efficiency of 19.1%.     

Wideband All-Polarization-Maintaining Yb-Doped Mode-Locked Fiber Laser Using a Nonlinear Optical Loop Mirror

We report on a wide-band and stable mode-locked all-polarization-maintaining fiber iaser configuration using a noniinear optical loop mirror.The central wavelength of the laser is 1080.14 nm and the 3dB bandwidth is 20.29 nm.The repetition rate of the pulse is 3.28 MHz and the pulse width is 848 ps.By tuning the pump power,which is centered at 980 nm,from 300 mW to 380 mW,we obtain a linearly changed output power from 6mW to 7.12 mW.The all-polarization-maintaining fiber configuration is fundamental to the stability of the output power.     

8字形腔波长可调谐锁模脉冲光纤激光器

采用非线性光纤环形镜加脉冲锁模技术及可调谐光纤光栅滤波器,对8字形腔被动锁模掺铒光纤激光器进行了波长可调谐输出的实验研究.在EDFA抽运光功率一定的情况下,通过调节偏振控制器和可调谐光纤光栅滤波器,获得了光谱稳定、重复频率1.1 MHz、输出功率起伏小于0.8 dBm、中心波长在1 548~1 570 nm内连续可调的短脉冲输出.该激光器可实现自启动锁模,且长时间稳定工作无需任何调整.     

基于光纤中超短脉冲非线性传输机理与特定光谱选择技术的多波长飞秒激光的产生

高集成、高可靠性宽调谐飞秒激光源在超快光谱学、量子光学及生物成像等研究与应用领域具有重要价值.如在生物多光子显微成像中,具有适中能量的宽调谐飞秒激光源不仅可满足多种生物组织荧光激发所需的峰值功率与激发波长,而且也可以显著提升非线性荧光产生效率、成像分辨率以及增大成像穿透深度.采用自主研发的高可靠性全保偏光纤飞秒激光器作为抽运源,基于低色散光纤中高峰值功率飞秒激光脉冲非线性传输引起的光谱加宽机制,本文开展了多波长全光纤飞秒激光产生技术研究.通过采用中心波长在980, 1000,1050, 1070与1100 nm的带通滤波片选择性地对单模光纤输出光谱中最左边与最右边光谱旁瓣进行滤波,在上述中心波长处分别可获得203, 195, 196, 187与194 fs的激光输出.本文提出的基于全光纤飞秒激光脉冲在单模光纤中非线性传输引起的光谱加宽机制与特定光谱选择技术的实验方案为高集成、高可靠性宽调谐飞秒激光源的实现提供了新的研究途径.     

被动锁模Yb3+光纤环形腔激光器的研究

 采用974 nm半导体激光器作为泵浦源，超高掺杂Yb³⁺光纤作为增益介质，利用光纤的非线性偏振旋转效应，得到稳定的ps量级锁模光脉冲。泵浦功率220 mW时，激光器锁模阈值功率150 mW，输出功率26 mW，锁模光脉冲中心波长1 046 nm，3 dB带宽6.01 nm，20 dB带宽16 nm，脉宽22 ps，重复频率20 MHz。与同类光纤激光器相比，该激光器输出功率高，具有更好的稳定性。     

自调Q、自锁模铒/镱共掺光纤激光器

研究了结构新颖的环形腔铒/镱（Er/Yb）共掺双包层光纤激光器.为了获得高功率激光输出，使用6个激光二极管（LD）同时抽运Er/Yb共掺光纤，采用光纤光栅（FBG）Sagnac环作为波长选择器，得到了中心波长为1548.11 nm、谱线宽度为0.06 nm的窄线宽激光输出；并利用增益光纤作为可饱和吸收体，实现了自调Q、自锁模脉冲输出.当抽运功率为719 mW时，激光器输出自调Q脉冲，脉冲周期为20μs，脉冲宽度为2.8μs，脉冲的平均功率为38.4mW，峰值功率为274.3mW；当抽运功率为3.6 W时，激光器输出自锁模脉冲，脉冲宽度为4ns，平均功率为319 mW，脉冲峰值功率大于10 W，重复频率为7.937 MHz.     

基于氧化石墨烯的瓦级调Q锁模Tm:LuAG激光器

在Tm:LuAG全固态激光器中实现了以氧化石墨烯可饱和吸收体为锁模启动元件的瓦级被动调Q锁模运转.本实验装置以可调谐掺钛蓝宝石激光器作为泵浦源,测得Tm:LuAG固态激光器出光阈值最低为325mW,当吸收抽运功率达到3420 mW时,进入稳定的调Q锁模运行状态.当抽运功率达到8.1 W时,对应的最大输出功率为1740 mW,中心波长为2023 nm,重复频率为104.2 MHz,最大单脉冲能量为16.7 nJ,调制深度接近100%.     

超低频率全正色散半导体可饱和吸收镜被动锁模光纤激光器

 通过延长激光器环形腔腔长,利用高浓度掺杂的单模掺镱光纤,搭建了超低重复频率、全正色散结构的半导体可饱和吸收镜被动锁模光纤激光器。激光器的中心波长、重复频率、平均功率及单脉冲能量分别为1 064 nm,281.5 kHz,11 mW和39 nJ。为了稳定中心波长,实现自启动,激光器腔体内接入了一个带通滤波器。该激光器运行稳定,无调Q不稳定现象,极大减小了半导体可饱和吸收镜被损坏的机会。     

980-nm all-fiber mode-locked Yb-doped phosphate fiber oscillator based on semiconductor saturable absorber mirror and its amplifier

A 980-nm semiconductor saturable absorber mirror(SESAM) mode-locked Yb-doped phosphate fiber laser is demonstrated by using an all-fiber linear cavity configuration. Two different kinds of cavity lengths are introduced into the oscillator to obtain a robust and stable mode-locked seed source. When the cavity length is chosen to be 6 m, the oscillator generates an average output power of 3.5 m W and a pulse width of 76.27 ps with a repetition rate of 17.08 MHz. As the cavity length is optimized to short, 4.4-m W maximum output power and 61.15-ps pulse width are produced at a repetition rate of 20.96 MHz. The output spectrum is centered at 980 nm with a narrow spectral bandwidth of 0.13 nm. In the experiment, no undesired amplified spontaneous emission(ASE) nor harmful oscillation around 1030 nm is observed. Moreover,through a two-stage all-fiber-integrated amplifier, an output power of 740 m W is generated with a pulse width of 200 ps.     

Tunable multi-wavelength fiber ring laser based on a Hi-Bi fiber loop mirror

A novel tunable multi-wavelength fiber ring laser based on semiconductor optical amplifier(SOA)is proposed by using a high-birefringence(Hi-Bi)fiber loop mirror(FLM)as wavelength filter.With this configuration,the wavelength spacing of this laser can be varied by using the different lengths of Hi-Bi fiber.8 wavelengths spacing on 450 GHz are experimentally obtained with more than 25-dB signal-to-noise ratio(SNR)for each channel using 1.28-m Hi-Bi fiber in Hi-Bi FLM.The output power variation between different channels is measured to be less than 5.9 dB.The linewidth of each channel is compressed from 0.347 to 0.186 nm by 1.5-m unpumped erbium-doped fiber(EDF).Meanwhile,17 wavelengths spacing on ITU-gird(100 GHz)are also obtained with 5.9-m Hi-Bi fiber in Hi-Bi FLM.All these channels can be tuned together over 0.4 nm.     

Diode-pumped femtosecond Yb:KGd(WO(4))(2) laser with 1.1-W average power

We demonstrate what is to our knowledge the first mode-locked Yb:KGd(WO(4))(2) laser. Using a semiconductor saturable-absorber mirror for passive mode locking, we obtain pulses of 176-fs duration with an average power of 1.1 W and a peak power of 64 kW at a center wavelength of 1037 nm. We achieve pulses as short as 112 fs at a lower output power. The laser is based on a standard delta cavity and pumped by two high-brightness laser diodes, making the whole system very simple and compact. Tuning the laser by means of a knife-edge results in mode-locked pulses within a wavelength range from 1032 to 1054 nm. In cw operation, we achieve output powers as high as 1.3 W.     

67.9W高功率全光纤白光超连续谱激光器

利用自主研发的全光纤被动锁模激光器以及高功率光纤模场匹配器,将145 W的皮秒脉冲耦合进国产光子晶体光纤,实现了67.9 W的高功率全光纤结构白光超连续谱输出,光谱范围为500~1700nm,10dB光谱宽度大于1000nm(泵浦波长除外)。整个激光器系统的光-光(半导体泵浦源输出激光-超连续谱输出激光)转化效率达到33.8%。     

Highly stable, passively mode-locked fiber laser with low pump power for subpicosecond pulse generation

We present the design of highly stable, passively mode-locked fiber lasers which are based on a simple configuration and require a low pump power for the generation of optical pulses with subpicosecond pulsewidth. Our designed fiber laser uses a semiconductor saturable absorber mirror to realize the self-starting, passive mode locking at a low pump power of 29 mW, with which a stable optical pulse train is obtained at the fundamental repetition rate of 52.5 MHz and the central wavelength of 1557 nm. The output mode-locked optical pulses have a pulsewidth of 881 fs and an average output power of 1.78 mW, respectively.     

基于石墨烯的1 064 nm连续锁模超短脉冲激光器

介绍了利用沉积在增透镜上的石墨烯薄膜作为可饱和吸收体、808 nm激光二极管端面泵浦Nd∶YVO4晶体的1 064 nm连续锁模激光输出特性。采用W型折叠谐振腔结构,在808 nm泵浦功率为8.0 W时,有稳定的连续锁模脉冲输出,平均输出功率达到185 mW;当抽运功率增加到16.0 W时,获得了中心波长1 063.4 nm、脉冲宽度为518 fs、重复频率为66.7 MHz、最大平均输出功率为323 mW的百飞秒量级超短脉冲激光输出。实验结果表明:石墨烯具有优良的可饱和吸收性,在1 064 nm波段能够实现高功率、百飞秒量级连续锁模脉冲激光输出。