铌酸钾钠基无铅压电陶瓷的高压电活性研究进展

以Pb(Zr_(1–x)Ti)x)O)3(PZT)为代表的铅基压电陶瓷因为具有良好的压电性能和机电耦合性能已被广泛应用于科技、工业、军事以及日常生活中.但是, PZT基陶瓷中Pb的含量超过了60%(质量比),在生产、使用及废弃处理过程中都会给人类生态环境造成严重损害.因此,发展无铅压电陶瓷已成为世界压电陶瓷研究的热点之一.铌酸钾钠(K_(0.5)Na_(0.5))NbO_3 (KNN)无铅压电陶瓷因为具有较为优异的压电性能以及较高的居里温度,被认为是最可能取代铅基压电陶瓷的材料体系之一.经过研究者们的努力工作,改性后的KNN基无铅压电陶瓷压电性能已经接近或超过了某些铅基压电陶瓷的性能.本文综合介绍了具有高压电活性的KNN基无铅压电陶瓷国内外的研究进展,重点阐述了高性能铌酸钾钠基无铅压电陶瓷制备工艺及相关理论基础的研究进展,并就今后铌酸钾钠基无铅压电陶瓷研究发展的方向及前景提出建议.     

溶胶-凝胶法制备Bi0.5Na0.5TiO3陶瓷及其电学特性

用溶胶-凝胶工艺成功制备出Bi05Na05TiO3纳米微粉，并利用此微粉烧结出高致密度的Bi05Na05TiO3陶瓷.这种新工艺制备的Bi05Na05TiO3陶瓷，其压电性能远远高于普通方法制备的陶瓷，其中压电常数d33和机电耦合系数kt分别高达102×10-12C/N和58%.同时发现，对于这种Bi05Na05TiO3陶瓷，室温时只需施加100kV/cm左右的交变电场，就可得到矩形度极好的饱和回线，得到的剩余极化Pr和矫顽场Ec分别为32μC/cm2和61kV/cm.而在100℃以上只需施加35kV/cm的极化电场就可使样品充分极化.     

铌酸钾钠基无铅压电陶瓷纵振换能器*

高性能环境友好型无铅压电陶瓷及其应用是当前压电材料研究的热点之一,为了探究其在水声换能器领域的应用潜力,该文对铌酸钾钠基无铅压电陶瓷和锆钛酸铅压电陶瓷纵振式换能器进行了对比研究。依据仿真结果优化结构尺寸,制作了两种换能器样机并测试了其在空气中和水中的电声性能。测试结果表明,铌酸钾钠基无铅压电陶瓷换能器的谐振频率为35kHz,最大发送电压响应为 151dB,声源级可达 190dB,在 26kHz~67kHz 的频率范围内发送电压响应的起伏不超过±4.5dB,谐振频率处-3dB 的指向性开角约为 76°。该无铅压电陶瓷换能器具有和锆钛酸铅压电陶瓷换能器相当的发射性能,有望推动无铅压电材料在水声换能器领域的应用进程。     

非化学计量和掺杂对(Na1/2Bi1/2)0.92Ba0.08TiO3陶瓷电性能的影响

研究了非化学计量和掺杂对无铅压电陶瓷(Na_1/2Bi_1/2)_0.92Ba_0.08TiO₃的压电性能及去极化温度的影响.研究发现A位非化学计量可以提高陶瓷的压电性能;B位掺杂对材料电学性能的影响规律类似于Pb(Ti,Zr)O₃系压电陶瓷的相关规律;由于非化学计量和掺杂会影响到A位离子对B位离子与氧离子形成的BO₆八面体的耦合作用,影响到畴的稳定性,从而影响 关键词： 无铅压电陶瓷 非化学计量 掺杂 电性能     

铌酸钾钠基无铅压电陶瓷的X射线衍射与相变分析

分析了斜方相、四方相铌酸钾钠基无铅压电陶瓷材料的结构和X射线衍射图谱的特点. 对于铌酸钾钠基压电材料斜方相结构, 从构成晶胞的一个单斜原胞进行分析, 计算出X射线衍射谱上每个衍射角附近的衍射峰数目和相对强度. 提出了2θ在20°—60°范围内根据(1 0 2)衍射峰(52°附近)和(1 2 1)衍射峰(57°附近)劈裂的数目区分斜方和四方相的新方法. 对于多晶陶瓷粉末, 可以更简便的由22°(或45°)附近前后峰的相对高低来判断斜方、四方相. 关键词： 铌酸钾钠 无铅压电陶瓷 X射线衍射 相变     

溶胶-凝胶法制备的高压电常数（Bi0.5Na0.5）1－xBaxTiO3系无铅压电陶瓷

测量了使用溶胶-凝胶工艺制备的(Bi0.5Na0.5)1-xBaxTiO3(x=0.00，0.04，0.06，0.08,0.12)系陶瓷的介电、压电、铁电和热释电性能.由于使用了溶胶-凝胶工艺制备的粉料，因此所有样品的压电性能都得到了较大提高.其中(Bi0.5Na0.5)0.94Ba0.06TiO.3系陶瓷具有该系列最大的压电常数，d33=173×10-12C/N，与传统工艺相比，d33提高了近40%.同时，在一定范围内，随Ba含量的增加，材料的剩余极化Pr和矫顽场Ec逐渐减小，退极化温度逐渐降低.对于(Bi0.5Na0.5)0.94Ba0.06TiO.3系陶瓷，剩余极化和矫顽场分别为25μC/cm2和28kV/cm，退极化温度约为80℃. 关键词： 溶胶-凝胶 压电常数 剩余极化 矫顽场     

Na1/2Bi1/2TiO3体系的电子结构与极化特性

采用自洽场离散变分X_α计算方法,研究了ABO₃型钙钛矿结构无铅压电陶瓷Na_1/2Bi_1/2TiO₃体系的电子结构,分析了A,B位元素取代对Na_1/2Bi_1/2TiO₃压电陶瓷极化性能的影响.结果表明:NBT体系压电陶瓷材料存在自发极化,B位离子位移使铁电性增强,Ba,Sr与Mn离子A,B位复合取代可降低矫顽场、提高自发极化强度,从而提高材料的铁电性能,并通过实验对此结论进行了验证.     

CaTiO3基微波介质陶瓷的频率温度稳定性

通过对克劳修斯-莫索蒂方程的近似, 分析了钙钛矿结构微波介质陶瓷频率温度系数 (τ_f) 的主要影响因素, 发现改变材料介电响应中离子位移极化和电子位移极化的比例, 可调节频率温度系数的正负与大小. 通过电子结构计算和容忍因子分析, 预测引入(Zn_1/3Nb_2/3)⁴⁺对具有正温度系数 的CaTiO₃进行B位取代将提高材料电子极化响应比例, 调节τ_f由正变负. 采用偏铌酸盐为前驱体, 通过固相反应法合成了Ca[(Zn_1/3Nb_2/3)_xTi_(1-x)]O₃钙钛矿结构陶瓷, 并对其进行结构分析和性能测试, 实验结果与理论分析一致, 获得了具有近零频率温度系数的Ca[(Zn_1/3Nb_2/3)_0.7Ti_0.3]O₃介质陶瓷材料. 关键词： B位复合钙钛矿陶瓷 谐振频率温度稳定性 极化机理 6八面体倾斜')" href="#">BO₆八面体倾斜     

高居里温度铋层状结构钛钽酸铋(Bi_3TiTaO_9)的压电、介电和铁电特性

随着现代信息技术的飞速发展,压电材料的应用范围进一步拓展,使用的温度环境越来越严苛,在一些极端环境下对压电材料的服役性能提出了新的挑战.因此研究具有高居里温度同时具有较强压电性能的压电材料,是迫切需要解决的问题.本文利用普通陶瓷工艺制备了高居里温度铋层状结构钛钽酸铋Bi_3TiTaO_9+x wt.%CeO_2(x=0—0.8,简写为BTT-10xCe)压电陶瓷,研究了钛钽酸铋陶瓷的压电、介电和铁电特性.压电特性研究表明,稀土Ce离子的引入可以提高BTT陶瓷的压电性能, BTT-6Ce (x=0.6)陶瓷具有最大的压电系数d33～16.2 pC/N,约为纯的BTT陶瓷压电系数(d33～4.2 pC/N)的4倍.介电特性研究显示, BTT和BTT-6Ce (x=0.6)陶瓷均具有高的居里温度, T_C分别为890℃和879℃,同时稀土Ce离子的引入降低了BTT陶瓷的高温介电损耗tand.铁电特性研究表明,稀土Ce离子的引入提高了BTT陶瓷的极化强度.在180℃温度下和110 kV/cm的电场驱动下, BTT和BTT-6Ce (x=0.6)陶瓷的矫顽场Ec分别为53.8 kV/cm和57.5 kV/cm,剩余极化强度Pr分别为3.4μC/cm~2和5.4μC/cm~2.退火实验显示:稀土Ce离子组分优化的BTT压电陶瓷经800℃的高温退火后,仍具有优异的压电性能温度稳定性.研究结果表明, BTT-6Ce (x=0.6)陶瓷兼具高的居里温度T_c约为879℃和强的压电性能d33约为16.2 pC/N、较好的压电性能温度稳定性,是一类压电性能优异的高温压电陶瓷.     

压电陶瓷的高温极化

极化处理是制作压电陶瓷器件的关键工艺之一．本文报告了压电陶瓷在居里点以上开始加电场的高温极化工艺和极化后样品主要性能的测试结果．对高温极化工艺与普通极化工艺的结果进行了比较;讨论了两种不同的极化工艺的优缺点．     

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5Na0.5NbO3- 0.04LiSbO3 lead-free piezoelectric ceramics

Effects of A-site non-stoichiometry on the structural and electrical properties of 0.96K0.5+xNa0.5+xNbO3- 0.04LiSbO3 lead-free piezoelectric ceramics were examined for 0 ≤ x ≤ 0.02. The piezoelectric coefficients exhibited a maximum, d33 = 187 pC/N at x = 0.0075, coinciding with the maximum of the grain size and the apparent density at x = 0.0075. The apparent density and the piezoelectric coefficients decreased with increasing x at higher x which was likely due to the crystal geometrical distortion of 0.96K0.5+xNa0.5+xNbO3-0.04LiSbO3. In addition, super-large grains were found and this may be due to liquid phase sintering. Excess (K++Na+) attracted a sum of space charges to keep the charge neutral, resulting in charge leakage during the course of ceramic polarization, influencing the piezoelectric and ferroelectric properties. These findings are of importance for guiding the design of K0.5Na0.5NbO3-based lead-free ceramics with enhanced electrical properties.     

Structure, ferroelectric and piezoelectric properties of (Bi1−x−yNa0.925−x−yLi0.075)0.5BaxSryTiO3 lead-free piezoelectric ceramics

Lead-free multi-component ceramics (Bi_1−x−yNa_{0.925−x−y}Li_0.075)_0.5Ba_xSr_yTiO₃ have been prepared by an ordinary sintering technique and their structure and electrical properties have been studied. All the ceramics can be well-sintered at 1100 °C. X-ray diffraction patterns shows that Li⁺, Ba²⁺ and Sr²⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure, and a morphotropic phase boundary (MPB) is formed at 0.04 < x < 0.08. As compared to pure Bi_0.5Na_0.5TiO₃ ceramic, the coercive field E_C of the ceramics decreases greatly and the remanent polarization P_r of the ceramics increases significantly after the formation of the multi-component solid solution. Due to the MPB, lower E_C and higher P_r, the piezoelectricity of the ceramics is greatly improved. For the ceramics with the compositions near the MPB (x = 0.04–0.08 and y = 0.02–0.04), piezoelectric coefficient d₃₃ = 133–193 pC/N and planar electromechanical coupling factor k_P = 16.2–32.1%. The depolarization temperature T_d reaches a minimum value near the MPB. The temperature dependences of the ferroelectric and dielectric properties suggest that the ceramics may contain both the polar and non-polar regions at temperatures near/above T_d.     

Glassy-ferromagnetic behavior in Eu0.5Sr0.5CoO3

Polycrystalline perovskite cobalt oxide Eu_0.5Sr_0.5CoO₃ was prepared by the conventional solid-state reaction method. X-ray powder patterns indicated the prepared samples are pure, cubic perovskite structure (Pm3?m), and with no evidence of any secondary phases. The dc magnetization and ac susceptibility measurements were carried out to investigate the magnetic properties of the sample, and which indicated that cluster-glasses properties are suppressed with the increasing of the coercive field. We denied the possibility of spin-glasses and the existence of the Hopkinson effect in Eu_0.5Sr_0.5CoO₃ through the temperature-dependent ac susceptibility measurements, and explained the magnetic behavior of Eu_0.5Sr_0.5CoO₃ with the competition between magnetic anisotropy and the external magnetic field.     

Photoluminescence at room temperature in Ba0.5Sr0.5TiO3 ceramics

We present in this paper the experimental results of photoluminescence spectra of Ba_0.5Sr_0.5TiO₃ ceramics. An emission band centered at about 920 nm has been observed at room temperature. When we change the amount of oxygen vacancies in these samples by thermal treatment, these samples show an enhancement of luminescence. Our experimental results indicate that the origin of the photoluminescence is related to the oxygen vacancies in these samples.     

Improving microwave dielectric properties of La2.98/3Sr0.01(Mg0.5Sn0.5)O3 ceramics with CuO additive

The microwave dielectric properties of CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were investigated with a view to their application in microwave devices. CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method. The X-ray diffraction patterns of CuO-doped La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics exhibited no significant variation of phase with sintering temperature. By adding 0.75 wt.% CuO, a dielectric constant of 20.07, a quality factor (Q × f) of 63,000 GHz, and a temperature coefficient of resonant frequency τ_f (−77.0 ppm/°C) were obtained when La_2.98/3Sr_0.01(Mg_0.5Sn_0.5)O₃ ceramics were sintered at 1500 °C for 4 h.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

Microstructures and microwave dielectric properties of La1-xBx(Mg0.5Sn0.5)O3 ceramics

The microwave dielectric properties of La_1-xB_x(Mg_0.5Sn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La_1-xB_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La_0.995B_0.005(Mg_0.5Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. A maximum apparent density of 6.58 g/cm³, a dielectric constant (ε_r) of 19.8, a quality factor (Q × f) of 41,800 GHz, and a temperature coefficient of resonant frequency (τ_f) of −86 ppm/°C were obtained for La_0.995B_0.005(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h.     

Dielectric and piezoelectric properties of non-stoichiometric (K0.5Na0.5)(Nb0.9+xTa0.1)O3 ceramics

In the study, in order to develop the lead-free piezoelectric ceramics for actuator, transformer and other electronic-devices application, (K_0.5Na_0.5)(Nb_0.9+xTa_0.1)O₃ + 0.5 mol% CuO + 0.2 mol% MnO₂ ceramics were prepared by conventional mixed oxide method. The effects of B-site non-stoichiometry in [(K_0.5Na_0.5)] [(Nb_0.9+xTa_0.1)O₃] ceramics on microstructure and piezoelectric properties were investigated. The density, electromechanical coupling factor (k_p), mechanical quality factor (Q_m), piezoelectric constant (d₃₃), T_C and T_O-T of NKNT ceramics with x = 0.0065 showed the optimum values of 4.58 g/cm³, 0.427, 1554, 109 pC/N, 373 °C and 226 °C, respectively, suitable for piezoelectric motor, and transformer applications.     

脱氧La0.5Ca0.5MnO3样品的铁磁-反铁磁转变和电阻率变化

研究了氧空位对La_0.5Ca_0.5MnO₃ （LCMO）多晶块材的电输运和磁性质的影响. 随着氧空位的增加, 样品在高温段的电阻率一直增加, 并满足绝热小极化子模型, 而低温段的电阻率先下降后上升, 并出现明显的dR/dT>0的行为, 直至最后变为绝缘的. 氧空位的增加抑止了反铁磁相的出现, 使得脱氧的LCMO样品不发生反铁磁转变, 进一步增加氧空位则会抑制铁磁相. 关键词： 0.5Ca_0.5MnO₃')" href="#">La_0.5Ca_0.5MnO₃ 反铁磁相变 铁磁相变 脱氧     

Effect of calcination temperature on the structure and hydroxylation activity of Ni0.5Cu0.5Fe2O4 nanoparticles

Nanocrystalline Ni_0.5Cu_0.5Fe₂O₄ was synthesized by sol-gel method with varying calcination temperature over the range of 500-1000. The powders obtained were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). In addition, thermal analysis (TG-DTG-DTA) of the precursor was carried out. The study reveals the simultaneous decomposition and ferritization process at rather low temperature (280-350). For the crystalline structure investigated, single cubic spinel is gained when the precursor was decomposed at 800-1000, whereas separated crystal CuO formed when calcination temperature is below 800. The increase of calcination temperature favors the appearance of Fe_B³⁺, Cu_A²⁺ and O on the spinel surface. The hydroxylation activity is relative to the amount of Cu_B²⁺ species on the spinel surface. The lattice oxygen species on the spinel surface are favorable for the deep oxidation of phenol.