VDF（52）／TrFE（48）铁电共聚物的非晶介电弛豫

用液氮淬火和热处理方法制得结晶度相差较大的铁电共聚物ＶＤＦ（５２）／ＴｒＦＥ（４８）试样。介导弛豫研究提示室温以下共聚物的频率谱由低频和高频两部分组成。低频部由非晶区被冻结分子链段的微布郎运动贡献。符合ＷＬＦ方程；高频部由晶区分子链段较小尺度的局域运动产生，遵从Ａｒｒｈｅｎｉｕｓ规律。分峰拟合结果得到共聚物的玻璃化转变温度为－２４℃，局域弛豫活化能为４６．１ｋＪ／ｍｏｌ．     

巨介电常数氧化物CaCu3Ti4O12的介电和阻抗特性

采用固相烧结法合成了单相巨介电常数氧化物CaCu₃Ti₄O₁₂（CCTO）.用阻抗分析仪分析了10—420 K温度范围内的介电频谱和阻抗谱特性,并结合ZVIEW软件进行了模拟.结果表明：温度高于室温时,频谱出现两个明显的弛豫台阶,低频弛豫介电常数随温度升高而显著增大,表现出热离子极化特点;温度低于室温时,频谱表现出类德拜弛豫,且高、低平台介电常数值基本不随温度变化,表现出界面极化特点和较好的温度稳定性.频谱中依次出现的介电弛豫对应于阻抗谱中 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电频谱 阻抗谱 Cole-Cole半圆弧     

Na0.25K0.25Bi0.5TiO3无铅压电陶瓷的介电特性研究

用固相反应法制备了Na_0.25K_0.25Bi_0.5TiO₃ (NKBT50)陶瓷，研究了该陶瓷在室温至400℃温度范围内的介电性能.发现该陶瓷的介电温谱与烧结气氛、极化状态有关.在空气中烧结的未极化样品在70℃附近存在介电和损耗峰，而极化后及在氧气氛中烧结的样品并不存在该介电、损耗峰.分析认为70℃的介电和损耗峰与氧空位形成的缺陷偶极子的极化弛豫有关.热激电流显示，陶瓷的去极化温度为225℃，与此相对应的介电、损耗峰也 关键词： 介电性能 氧空位 极化弛豫 钛酸铋钠钾     

CaCu3Ti4O12陶瓷的介电特性与弛豫机理

本文采用Novocontrol宽频介电谱仪在-100 ℃–100 ℃温 度范围内、0.1 Hz–10 MHz频率范围内测量了表面层打磨前 后CaCu₃Ti₄O₁₂陶瓷的介电特性, 分析了CaCu₃Ti₄O₁₂陶瓷的介电弛豫机理. 首先, 基于对宏观“壳-心”结构的定量分析, 排除了巨介电常数起源于表面层效应的可能性; 其次, 基于经典Maxwell-Wagner夹层极化及其活化能物理本质的分析, 排除了巨介电常数起源于经典Maxwell-Wagner极化的可能性; 最后, 依据晶界Schottky势垒与本征点缺陷的本质联系, 提出了巨介电常数起源于Schottky势垒边界陷阱电子弛豫的新机理. 陷阱电子弛豫机理反映了CaCu₃Ti₄O₁₂陶瓷本征点缺陷、 电导、介电常数之间的本质关系. 关键词： 3Ti₄O₁₂')" href="#">CaCu₃Ti₄O₁₂ 介电弛豫 Schottky势垒 点缺陷     

氧气氛低温退火Pt/Ba0.8Sr0.2TiO3Pt引起的低频介电弛豫效应

研究了在不同温度区间氧气氛和氮气氛退火后处理对PtBa0.8Sr0.2TiO3Pt介电特性的影响.经过高温550℃氮气退火处理后,再放入350℃的氧气中退火,发现样品的介电特性出现了非常明显的低频弛豫现象,并且这种低频弛豫现象在350℃的氮气中退火后将会消失.通过在出现低频弛豫现象的样品的上下电极加一偏压,可以发现低频弛豫现象更加明显,并且在撤消偏压后这种增强将会逐渐减弱,直至最终恢复到偏压前的弛豫状态 关键词： 脉冲激光沉积 介电弛豫 动态随机存储器     

甲基丙烯酸甲酯-萘乙烯共聚物的NMR研究Ⅱ.甲基丙烯酸甲酯-萘乙烯共聚物的核弛豫研究

用核弛豫研究了溶液中甲基丙烯酸甲酯-萘乙烯共聚物体系中高分子链间的凝聚态结构.通过对溶液中甲基丙烯酸甲酯-萘乙烯共聚物的变温¹³C NMR自旋-晶格弛豫的研究,发现此体系具有类似小分子在溶液中的弛豫特性.变温¹H NMR自旋-自旅弛豫呈现出双指数特性,弛豫快的部分随温度升高而减少对应于聚合物链间凝聚缠结的解缠,当温度继续升高时,主链的这种组分又开始增加,说明主链中形成新的缠结.研究结果还表明,在这种共聚物中,例基萘环的叠加较少.     

PZT-8型铁电压电陶瓷的低频介电特性

本文研究PZT-8型多晶锆钛酸铅铁电压电陶瓷,通过介电温度、频率响应谱的研究,对它的损耗机制、弛豫过程、杂质影响等作了讨论,认为,高温时主要是电导损耗起作用,并对如何改进PZT-8型铁电陶瓷的电学性能,提出了相应的设想。 关键词：     

钛酸钡基施主掺杂弛豫铁电体介电弥散的唯象分析

弛豫铁电体铁电相变的介电弛豫性涉及外来离子掺杂或原有离子的有序排列, 需要深入理解和有效统一的表征. 针对高浓度施主掺杂在晶粒中产生金属离子缺位, 降低居里温度并引起钛酸钡基铁电材料扩散相变的现象, 分析了高斯型的杂质分布、居里温度分布和金属离子缺位分布的等效对应关系, 得出了在介电常数峰值温区金属离子缺位浓度随温度降低而作用增大的结论, 认为金属离子缺位引起的单极电荷在电场作用下的跳跃运动有可能引起介电弥散和介电损耗. 提出了用‘弛豫度’表征铁电弛豫程度.     

等静压和温度诱导的PbLa(Zr,Sn,Ti)O3反铁电陶瓷相变和介电性能研究

研究了等静压和温度诱导掺镧La的Pb(Zr,Sn,Ti)O₃(PLZST)陶瓷材料的铁电反铁电相变、介电压力谱和介电温度谱,研究了温度对压致相变和介电压力谱的影响,结果发现温度使铁电反铁电相变压力降低,介电压力谱具有明显的扩散相变和频率弥散的特点;研究了等静压对介电温度谱的影响,结果表明等静压使铁电反铁电相变温度降低,反铁电顺电相变温度升高.这些现象有利于丰富和拓宽人们对温度和压力诱导的多组元弛豫型铁电体和弛豫型反铁电体扩散相变和弛豫行为的认识和理解. 关键词： 等静压和压致相变 铁电反铁电相变 介电压力谱 介电温度谱     

基于小波变换的时域介电谱分析及其应用

应用小波变换改进时域介电谱的分析法扩宽其应用范围.实验结果表明,通过分析油水混合物的弛豫过程,基于小波变换的时域介电谱分析不但可得反映物性的整体频谱信息,还能得出反映各组成成分不同时域和频域信息.因此,该方法可应用于分析复杂多相混合物. 关键词： 时域介电谱 小波变换 油水混合物     

Dielectric relaxation of poly(ethylenglycol)- b-poly(propylenglycol)-b-poly(ethylenglycol) copolymers above the glass transition temperature

The complex dielectric permittivity has been measured for three poly(ethylenglycol)-b-poly(propylenglycol)-b-poly(ethylenglycol) copolymers with different content of poly(ethylenglycol) (15%, 33% and 80%), and increasing degree of crystallinity (0%, 10% and 20%, respectively). Only the non-crystalline sample shows the normal mode relaxation together with the segmental (α-relaxation) and the Johari-Goldstein (β-relaxation) modes. The crystalline samples show also polarization contributions due to the existence of interfaces between the crystallites and the amorphous phase. The relaxation times of the (α and normal modes can be described by a VFT equation with the same value of T₀. There is a slowing-down of the segmental mode due to the presence of crystallites. The temperature dependence of the α and β relaxations in the copolymers is very similar to that found in pure PPG, while there are significant differences in the case of the normal mode of the non-crystalline sample. The size of the cooperatively rearranging regions CRR, and the width of the glass transition region increase slightly with the degree of crystallinity. The temperature dependence of the size of CRRs is compatible with the prediction of fluctuation theory. No systematic effect of the degree of crystallinity on the β-relaxation has been found. Near T _g the β-relaxation time is close to the primitive time of the coupling model. Received: 31 May 2000     

Revisiting the Dielectric Relaxation of Ethylene-Vinylacetate Copolymers: Influence of Microstructure

The dielectric relaxation behavior of a series of ethylene-vinylacetate (EVA) copolymers was investigated by measuring the complex dielectric permittivity in a broad frequency and temperature range. Crystallinity of EVA copolymers was estimated by differential scanning calorimetry (DSC) and wide-angle X-ray scattering (WAXS). The shape of the higher temperature relaxation, appearing above the glass transition temperature T _g depends on the VA content. It was found that this relaxation was asymmetric for VA concentrations higher than 40 wt% and changed to a symmetric shape at lower VA values. Concurrently, as the VA content decreased, a major broadening of the relaxation over a wide frequency range was observed. It is found that the dielectric relaxation was preserved on going through the melting range of the semicrystalline samples, although it exhibited changes of its characteristic parameters that are typical for segmental relaxation appearing at T _g. This finding allows one to associate this relaxation to the segmental motions at T _g in the amorphous phase and not to the existence of interfacial regions.     

Piezoelectric relaxations in homopolymers and copolymers of γ-Benzyl-L-glutamate and L-Leueine

The temperature dependence of the piezoelectric stress-constant, the piezoelectric strain-constant, and the Young's elastic constant is simultaneously determined for homopolymers and copolymers of γ-benzyl-L-glutamate [Glu(OBz)] and L-leucine (Leu). With the rise of temperature, the piezoelectric constants first increase due to the elastic relaxation in the Leu side chains (about ?150°C) and the Glu(OBz) side chains (about ?10°C), and then decrease due to the dielectric relaxation in the Glu(OBz) side chains. Higher piezoelectric constants are observed for the copolymers at low temperatures. This suggests that the shear-induced internal strain of the peptide dipoles is enhanced by heterogenity in the structure of side chains.     

DC conductivity and dielectric properties of maize starch/methylcellulose blend films

The transient current, electrical conductivity, dielectric constant (ε′), and dielectric loss factor (ε″) of starch and methylcellulose homopolymers and their blends with various compositions were studied under different conditions. The x-ray diffraction pattern was obtained for individual polymers and 50:50 wt/wt% blend sample to identify both the structure and degree of crystallinity. From transient current, the ionic and electronic transfer number as well as charge carrier density and drift mobility were determined. The values of activation energy in the temperature range 30–90 °C indicate that the conduction mechanism is due to combined electronic and ionic processes, while in the temperature range 100–160 °C, electronic contribution is predominant. The complex dielectric data of the present samples in an extended frequency and temperature range appear as different relaxation processes, which are connected with polymer dynamics.     

Crystallinity and dielectric relaxations in semi-crystalline poly(ether ether ketone)

The Maxwell-Wagner-Sillars (MWS) relaxation is studied for semi-crystalline polymers poly (ether ether ketone) (PEEK), in the range 20 Hz-1 MHz and temperature varying from 80 to 330 °C. The parameter is the crystallization condition in the case of PEEK, which is a semi-crystalline polymer considered as a particulate composite. The relaxation found in the semi-crystalline polymers above the α relaxation of the PEEK is ascribed to the trapping of conductive carriers at the interface between crystalline lamellae and the amorphous matrix. The study of PEEK microstructure is based on differential calorimetry and X-rays diffraction. Two lamellae populations have been detected, that depends on the crystallization temperature and its duration. The crystallinity rate is increasing with crystallization temperature and duration. In dielectric studies, the use of the electric modulus instead of permittivity allows us to minimize the ionic conduction and then leads to the appearance of the interfacial relaxation. According to our measurements, the crystallinity rate is not the main factor of the interfacial relaxation intensity, which also depends on the nature and degree of perfection of the lamellae.     

Dielectric relaxation and ac conductivity behavior of carboxyl functionalized multiwalled carbon nanotubes/poly (vinyl alcohol) composites

We study the dielectric relaxation and ac conductivity behavior of MWCNT-COOH/Polyvinyl alcohol nanocomposite films in the temperature (T) range 303–423 K and in the frequency (f) range 0.1 Hz–1 MHz. The dielectric constant increases with an increase in temperature and also with an increase in MWCNT-COOH loading into the polymer matrix, as a result of interfacial polarization. The permittivity data were found to fit well with the modified Cole-Cole equation. Temperature dependent values of the relaxation times, free charge carrier conductivity and space charge carrier conductivity were extracted from the equation. An observed increment in the ac conductivity for the nanocomposites was analysed by a Jonscher power law which suggests that the correlated barrier hopping is the dominant charge transport mechanism for the nanocomposite films. The electric modulus study revealed deviations from ideal Debye-type behavior which are explained by considering a generalized susceptibility function. XRD and DSC results show an increase in the degree of crystallinity.     

石英中Al3+-空穴取向变化弛豫过程中的红外发散响应

基于α石英的晶体结构，将红外发散响应模型和双势阱模型应用到含Ａｌ杂质的α石英中Ａｌ³⁺－空穴的取向变化弛豫过程，研究其低温介电损耗特性，结果表明Ｔ＜６．５Ｋ时，介电损耗的主要贡献来自于单声子助隧道弛豫过程；Ｔ＞１０Ｋ时，主要贡献来自于热跃迁弛豫过程；而在中间温区，介电损耗是两种过程的迭加，同一弛豫体不同的弛豫过程对应于不同的红外发散响应，还讨论了同一弛豫体引起的超声弛豫损耗。 关键词：     

Morphological,Thermal, and Electrical Characterization of Syndiotactic Polypropylene/Multiwalled Carbon Nanotube Composites

In this work, syndiotactic polypropylene/multiwalled carbon nanotubes (MWCNT) nanocomposites, in various concentrations, were produced using melt mixing. The influence of the addition of MWCNT on the morphology, crystalline form, and the thermal and electrical properties of the polymer matrix was studied. To that aim, scanning electron microscopy, Raman spectroscopy, X-ray diffraction, differential scanning calorimetry, and dielectric relaxation spectroscopy were employed. Significant alterations of both the crystallization behavior and the thermal properties of the matrix were found on addition of the carbon nanotubes: conversion of the disordered crystalline form I to the ordered one, increase of the crystallization temperature and the degree of crystallinity, and decrease of the glass transition temperature and the heat capacity jump. Finally, the electrical percolation threshold was found between 2.5–3.0 wt.% MWCNT. For comparison purposes, the results of the system studied here are also correlated with the findings from a previous work on the isotactic polypropylene/MWCNT system.     

Electric Modulus Spectroscopic Studies of the Dielectric Properties of Carbon Nanotubes/Epoxy Polymer Composite Materials

The electrical properties of epoxy polymer/carbon nanotubes composites were characterized using impedance spectroscopy in the frequency range between 1 Hz and 10 MHz and temperature range between 25°C and 105°C. We report the analysis of the experimental data using the electric modulus formalisms to understand the dielectric relaxation mechanisms. The variation of the real and imaginary parts of the electric modulus versus frequency and temperature were suggestive of two relaxation processes, associated with dipolar relaxation and CNT-polymer interfaces. The Havriliak-Negami model of dielectric relaxation was used for modelling the relaxation processes, extracting the relaxation parameters.     

dielectric relaxation in VDF<Subscript>60</Subscript>/Tr<Subscript>40</Subscript> and VDF<Subscript>88</Subscript>/Te<Subscript>12</Subscript> polar copolymers embedded in porous glass matrices

The dielectric properties of composite materials prepared by embedding P(VDF₆₀/Tr₄₀) and P(VDF₈₈/Te₁₂) polar copolymers in porous glass matrices with a mean flow-through pore diameter of around 320 nm were investigated in the temperature range 200–450 K. Strong dielectric relaxation, the characteristic time of which conformed to the Williams-Landel-Ferry law, was observed in the vicinity of glass transition point T _g of an amorphous fraction of polymer inclusions. An increase (≈10 K) in the T _g temperature of the amorphous fraction of incorporated polymeric materials was detected.