硼酸铅玻璃的光学二次谐波产生

对硼酸铅玻璃体材料样品进行热辅助的平板电场极化(简称热极化)后,通过观察其光学二次谐波(SHG)信号的强弱,得到了不同组分的样品的最佳极化温度,发现其最佳极化温度与玻璃化温度满足一定的关系;同时得到了不同组分的样品在各自的最佳极化温度条件下极化后的二次谐波信号强度与组分的关系;经过对一种组分的样品进行细致研究,发现样品的二次谐波信号强度随着极化电压的增大而增大,并满足幂函数关系.利用有效偶极子释放模型解释了样品的二次谐波信号强度与极化电压之间的超平方关系 关键词： SHG 玻璃 极化     

无锂助熔剂B_2O_3对Li_(1.3)Al_(0.3)Ti_(1.7)(PO_4)_3固体电解质离子电导率的影响

采用固相法制备锂离子电池用固体电解质磷酸钛锂铝Li_(1.3)Al_(0.3)Ti_(1.7)(PO_4)_3(LATP),研究了不同烧结温度以及助熔剂对LATP固体电解质离子电导率的影响.采用X射线衍射、能谱分析、扫描电镜和交流阻抗等方法,研究样品的结构特征、元素含量、形貌特征以及离子导电性能.结果表明,在900?C烧结可以获得结构致密、离子电导率较高的纯相LATP陶瓷固体电解质.与添加助熔剂Li BO2的样品进行对比实验发现,采用B_2O_3代替LiBO_2作为助熔剂也可以提高烧结样品的离子电导率,并且电解质的离子电导率随助熔剂添加量的增大,先增大后减小,其中添加质量百分比为2%的B_2O_3的样品具有最高的室温离子电导率,为1.61×10~(-3)S/cm.     

Magnetic properties of xFe2O3(1−x)[B2O3 · PbO] glasses

The magnetic measurements performed on xFe₂O₃(1-x)[B₂O₃ · PbO] glasses show that for x 5 mol.% Fe₂O₃ the thermal variation of reciprocal susceptibility obeys a Curie behaviour. For higher iron content, at T 50 K, a nonlinear variation, typical for systems with random distribution of exchange interactions is observed. At greater temperatures than 50 K a Curie-Weiss behaviour is shown. The composition dependence of the Curie constants is analysed in correlation with the number of Fe³⁺ and Fe²⁺ ions as determined from Mössbauer effect measurements. A comparison with the data obtained in case of xFe₂O₃(1-x)[3B₂O₃ · PbO] glasses is made.     

偏硼酸钡低温相的晶体结构

本文报道了新型信频材料——偏硼酸钡[Ba₃(B₃O₆)₂]低温相的晶体结构。晶体属三方晶系,空间群为C₃⁴-R3,取六方坐标系,晶胞参数为a=b=12.532?,c=12.717?,z=6。在PhilipsPW-1100四圆衍射仪上收集到独立衍射693个。采用重原子法通过三维帕特逊和三维傅里叶合成测定结构,并用对角矩阵最小二乘法修正至R=0.046。该晶体是一个由Ba²⁺和(B₃O₆)^3-环交错组成的层状阶梯式结构。其阴离子(B₃O₆)^3-环基本上是平面状的。基团平面垂直于三次轴;Ba²⁺近邻有7个氧原子。将此结构与偏硼酸钡高温相比较表明,由于钡阳离子的非中心对称分布改变了阴离子硼氧环共轭基团的电子云密度,这一结构上的变化对该晶体的倍频效应做了主要贡献。 关键词：     

Li2B4O7晶体及其熔体结构的拉曼光谱研究

采用高温原位拉曼光谱技术,研究了Li₂B₄O₇从常温至1 373 K温度范围内的拉曼光谱。在升温过程中,晶体的拉曼光谱出现展宽和红移现象,且强度降低。晶体熔化时,由2个[BO₄]和2个[BO₃]组成的[B₄O₉]环状结构转变成(B₃O₆)3- 六元环和[BO₃]结构,[BO₄]结构减少直至消失。基于密度泛函理论,计算了Li₂B₄O₇晶体的拉曼光谱,对其振动模式进行了分析归属。利用量子化学从头计算法计算了由[B₃O₆-BO₃]为基础相互连接形成的x(Li₂B₄O₇)(x=2, 3, …, 9)的环状团簇模型的拉曼光谱,对Li₂B₄O₇熔体的结构进行了模拟分析。计算结果表明Li₂B₄O₇熔体的阴离子基元为三个(B₃O₆-BO₃)组成的大三元环超级结构。     

B2O3添加宝石级金刚石单晶的生长特性

利用温度梯度法, 在5.3-5.7 GPa压力、1200-1600 ℃的温度条件下, 将B₂O₃粉添加到FeNiMnCo+C合成体系内, 进行B₂O₃添加宝石级金刚石单晶的合成. 研究得到了FeNiMnCo触媒生长B₂O₃添加宝石级金刚石单晶的相图分布规律. 结果表明B₂O₃添加会使晶体生长的“V”形区上移和低温六面体单晶生长区间变宽. 通过晶体生长实验, 研究合成了不同形貌的B₂O₃添加宝石级金刚石单晶. 研究同时证实, B₂O₃的过量添加会对宝石级金刚石单晶生长带来不利影响. 当B₂O₃的添加量高于约3 wt‰、生长时间超过20 h时, 很难实现优质B₂O₃添加宝石级金刚石单晶的生长. 但B₂O₃的适量添加(不超过1 wt‰), 有助于提高低温板状六面体宝石级金刚石单晶的成品率. 通过对晶体生长速度的研究发现, B₂O₃的添加使得优质晶体的生长速度明显降低, 随着晶体生长时间的延长, B₂O₃添加剂对晶体生长的抑制作用会越发明显. 扫描电镜测试结果表明, 合成体系内B₂O₃添加剂的引入, 导致晶体表面的平整度明显下降.     

Enhancement of positive temperature coefficient resistance effect of BaTiO3-based semiconducting ceramics caused by B2O3 vapor dopants

The positive temperature coefficient resistivity (PTCR) effect of semiconducting BaTiO₃ ceramics can be remarkably influenced by both dopants and ceramic processing. The behavior of B₂O₃ as vapor dopants was studied in this paper. It was found that the PTCR effect was enhanced distinctly, while the room temperature resistance also increased.     

Ce3+掺杂SiO2-Al2O3-Gd2O3玻璃的闪烁性能

通常, Ce离子掺杂的低密度玻璃有较高的发光效率, 而高密度的Ce离子掺杂玻璃其发光效率很低. 为了解释这一现象, 采用高温熔融法获得了SiO₂-Al₂O₃-Gd₂O₃三元系统的玻璃形成区, 并在还原气氛下制备了Ce³⁺掺杂SiO₂-Al₂O₃-Gd₂O₃以及SiO₂-Al₂O₃-Gd₂O₃-Ln₂O₃ (Ln=Y, La, Lu)闪烁玻璃, 研究了其光谱和闪烁性能. 测试结果显示: 随着Gd₂O₃含量增加, 玻璃紫外截止波长发生红移, 荧光强度降低, 衰减时间缩短; 加入Lu₂O₃, La₂O₃, Y₂O₃后, 紫外截止波长发生红移, 荧光强度降低, 衰减时间变短; 当Gd₂O₃超过10% mol时, X射线荧光积分光产额从相当于锗酸铋 晶体的61%降低到13%. 荧光强度降低、衰减时间缩短的原因是随着玻璃的紫外截止波长红移玻璃的能带宽度变窄, 使得Ce³⁺离子的d电子轨道开始接近玻璃的导带, Ce³⁺离子受辐射后跃迁到d电子轨道的电子会通过导带与玻璃中的空穴复合, 产生电荷迁移猝灭效应.     

碱金属阳离子对[B3O7]型非线性光学晶体结晶习性的影响

本文利用高温拉曼光谱技术和从头计算的方法, 研究了LiB₃O₅和CsB₃O₅晶体高温熔融体的结构, 分析了碱金属阳离子对熔体结构的影响, 以及熔体结构的差异与LiB₃O₅和CsB₃O₅晶体结晶习性的联系. 结果表明: LiB₃O₅和CsB₃O₅晶体高温熔融体中的结构基团 主要为B₃Ø₇和B₃Ø₆两种不同类型的硼氧六元环; 环内BØ₄ 四面体的数量影响了六元环呼吸振动峰的拉曼频率, 随BØ₄四面体数量的增加六元环呼吸振动峰向低频移动; LiB₃O₅晶体高温熔融体中, BØ₄四面体含量相对较多; 然而, 离子半径相对较大的Cs⁺离子却阻碍了熔体中BØ₄四面体的形成, 造成CsB₃O₅晶体高温熔融体中BØ₄/BØ₃比值的降低. 结合LiB₃O₅和CsB₃O₅晶体生长动力学过程的分析 (Wang D, Wan S M et al. 2011 Cryst. Eng. Comm. 13 5239), 阳离子的不同导致高温熔体中BØ₄四面体数量的差异, 被认为是影响LiB₃O₅和CsB₃O₅晶体结晶习性的重要因素, 有效降低高温熔体中BØ₄四面体的数量, 将是实现LiB₃O₅晶体生长的关键条件. 关键词： 硼酸盐晶体 熔体结构 拉曼光谱 结晶习性     

The role of Bi2O3 as a network modifier and a network former in xBi2O3 · (1 − x)LiBO2 glass system

The effect of Bi₂O₃ on the glass transition temperature, electrical conductivity and structure of LiBO₂ glass has been investigated. T_g vs. composition curve shows three different linear regions, while there is an overall decrease in T_g with the increase in Bi₂O₃ content. The slope of these three straight lines is in a decreasing order. These results are interpreted in terms of the increase in the number of non-bridging oxygen atoms, substitution of Bi-O bond in place of B-O bond and change in Li⁺ ion concentration. The conductivity vs. composition curve exhibits two maxima which are interpreted in terms of the structural modification effect of Bi₂O₃ on LiBO₂ network and mixed-former effect, respectively. Results obtained from the XPS studies of the samples of composition x 0.005, have shown that the number of non-bridging oxygen atoms from B-O bond increases with the increase in Bi₂O₃ content. It has a maximum value at x = 0.003 where the conductivity has also exhibited a maximum value. Further increase of Bi₂O₃ content causes decrease in it. For higher Bi₂O₃ content (x * > 0.005), O 1s spectra of Bi₂O₃ has been separated out from that of Bi₂O₃. Bismuth ions have been substituted for boron ions as network former ions.     

Investigations on conductivity anomalies in Li2O·4MnO1+x·4B2O3 glasses

Glassy material Li₂O·4MnO_1+x·4B₂O₃ (0<x<0.5) has been prepared by quenching the melt in air, and its electrical conduction behavior has been studied. Two conductivity anomalies are observed around the glass transition temperature. One appears in the dependence of the isothermal conductivity vs. the annealing time. This anomaly is attributed to the oxidation of Mn²⁺ by oxygen ions penetrating into the glass matrix, leading to the increase of the charge carrier density. The other anomaly is observed in the dependence of the conductivity vs. the temperature for different times of annealing. The abnormal increase and decrease of the conductivity vs. annealing time might result from a complicated structural variation in the glass. Below 200°C, the conductivity obeys an Arrhenius relation. Above 350°C, the formation of crystalline MnBO₃ causes a conductivity decrease by one order of magnitude. The conductivity is enhanced by the redistribution of free volume between these two temperatures.     

Eu3+掺杂Bi2O3-PbO-B2O3-ZnO玻璃光谱性质

用高温融熔法制备了Eu³⁺掺杂浓度为1%的(60-x)Bi₂O₃xPbO30B₂O₃10ZnO(x=0,10,30,摩尔分数)玻璃.测定了玻璃的差热分析曲线、吸收光谱、声子边带谱、发射光谱与激发光谱.由发射光谱与稀土Eu³⁺离子光学跃迁矩阵元的特点,计算了Eu³⁺光学跃迁的J-O参数Ω₂与Ω₄.结果显示强度参数Ω₂随着PbO量的增加而略减少,表明材料的对称性略增加,Eu—O键强减弱,共价性降低.PbO组分的增加,使玻璃的结晶起始温度与软化温度差降低,导致玻璃的热温度性变差.随着PbO的增加,电-声子耦合减弱.     

Enhanced luminescence from transparent Ni-doped MgO–Al2O3–SiO2 glass ceramics by Ga2O3 addition

Transparent Ni²⁺-doped MgO–Al₂O₃–SiO₂ glass ceramics without and with Ga₂O₃ were synthetized. The precipitation of spinel nanocrystals, which was identified as solid solutions in the glass ceramics, could be favored by Ga₂O₃ addition and their sizes were about 7.6 nm in diameter. The luminescent intensity of the Ni²⁺-doped glass ceramics was largely enhanced by Ga₂O₃ addition which could mainly be caused by increasing of Ni²⁺ in the octahedral sites and the reduction of the mean frequency of phonon density of states in the spinel nanocrystals of solid solutions. The full width at half maximum (FWHM) of emissions for the glass ceramics with different Ga₂O₃ content was all more than 200 nm. The emission lifetime increased with the Ga₂O₃ content and the longest lifetime is about 250 μs. The Ni²⁺-doped transparent glass ceramics with Ga₂O₃ addition have potential application as broadband optical amplifier and laser materials.     

沟道层厚度对室温制备的In2O3薄膜晶体管器件性能的影响

在室温下采用直流磁控溅射以SiO₂/Si为衬底制备了不同沟道层厚度的底栅式In₂O₃薄膜晶体管,讨论了沟道层厚度对底栅In₂O₃薄膜晶体管的电学性能的影响。实验结果表明:器件的特性与沟道层厚度有关,最优沟道层厚度的In₂O₃薄膜晶体管为增强型,其阈值电压为2.5 V,开关电流比约为10⁶,场效应迁移率为6.2 cm²·V^-1·s^-1。     

(1-x)Sr_3Sn_2O_7+xCa_3Mn_2O_7陶瓷合成及其光电性能

为了寻求新的非常规多铁性材料,采用固相合成方法制备具有Ruddlesden-Popper结构的(1-x)Sr_3Sn_2O_7+x Ca_3Mn_2O_7(SSO+CMO)(x=0,0.05,0.10,0.15,0.20)系列陶瓷.通过X射线衍射、紫外可见光谱和磁性测量,发现SSO+CMO陶瓷为单一正交相结构,空间群为A21am.随着掺杂量x的增加,样品的晶胞参数和体积相应地减小;在室温不同频率下,样品的介电常数和介电损耗随着频率增加而减小,且在x=0.1时有弱的铁磁性.     

The influence of different fabrication processes on characteristics of excess Bi2O3-doped 0.95 (Na0.5Bi0.5)TiO3–0.05 BaTiO3 ceramics

In this study, we will develop the influences of the excess x wt% (x=0, 1, 2, and 3) Bi₂O₃-doped and the different fabricating process on the sintering and dielectric characteristics of 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃ ferroelectric ceramics with the aid of SEM and X-ray diffraction patterns, and dielectric–temperature curves. The 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ ceramics are fabricated by two different processes. The first process is that (Na_0.5Bi_0.5)TiO₃ composition is calcined at 850 °C and BaTiO₃ composition is calcined at 1100 °C, then the calcined (Na_0.5Bi_0.5)TiO₃ and BaTiO₃ powders are mixed in according to 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions. The second process is that the raw materials are mixed in accordance to the 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions and then calcining at 900 °C. The sintering process is carried out in air for 2 h from 1120 to 1240 °C. After sintering, the effects of process parameters on the dielectric characteristics will be developed by the dielectric–temperature curves. Dielectric–temperature properties are also investigated at the temperatures of 30–350 °C and at the frequencies of 10 kHz–1 MHz.     

探索基于人工超晶格LaFeO3-YMnO3和自然超晶格n-LaFeO3-Bi4Ti3O12薄膜多铁性

基于纳米尺寸下复合铁电材料和反铁磁性材料是一个探索多铁性材料有效的方法. 利用激光脉冲沉积制备出LaFeO₃-YMnO₃人工超晶格和掺入不同层LaFeO₃, BiFeO₃的Bi₄Ti₃O₁₂的外延薄膜. 通过系统的X射线衍射、透射电子显微术、扫描透射电子显微术下的能量损失谱表征证明这些样品具有原子尺寸上清晰的界面和完整的层状结构. 磁性测试证明这些材料具有亚铁磁性. 特别是在0.5和1.5LaFeO₃-Bi₄Ti₃O₁₂中的亚铁磁性甚至能保持到室温. 就铁电性而言, 铁电性测试显示出LaFeO₃-YMnO₃和插入BiFeO₃的Bi₄Ti₃O₁₂样品中存在较大的漏电流, 而在0.5LaFeO₃-Bi₄Ti₃O₁₂样品中存在铁电性. 因此在0.5LaFeO₃-Bi₄Ti₃O₁₂中能够实现亚铁磁和铁电共存. 其次发现当掺入多层的钙钛矿(3层SrTiO₃或2.5层LaFeO₃)后, Bi₄Ti₃O₁₂ 的层状结构将出现结构失稳现象. 这些工作对于利用纳米复合开发新颖多铁性提供一些实例.     

B-MQMAS and Si–{B} Double-Resonance NMR Studies on the Structure of Binary B2O3–SiO2 Glasses

Glasses in the system x B₂O₃·(1−x)SiO₂ (0.2≤x≤1.0) were studied using ¹¹B multiple quantum magic angle spinning NMR spectroscopy (MQMAS), ²⁹Si–\{¹¹B\} rotational echo adiabatic passage double-resonance and ²⁹Si–\}¹¹B\{ CP heteronuclear correlation spectroscopy. The results can be quantitatively interpreted in terms of a phase separation of the borosilicate glasses into a virtually SiO₂-free B₂O₃ phase and a mixed borosilicate phase. While the MQMAS spectra allowed the site speciation and resolution of at least two different ¹¹B resonances, attributable to BO_3/2 units consumed in boroxol rings, BO_3/2 units connecting the boroxol rings and BO_3/2 units involved in B–O–Si linkages, the analysis of the double-resonance data further elucidated the structure of the mixed borosilicate phase. The results indicate that only a fraction of 0.48 mol B₂O₃ can be accommodated per mole SiO₂, building a mixed borosilicate network.     

Optical and electrical properties of binary WO3–Pb3O4 glasses

A glass system of the composition xWO₃+(100−x)Pb₃O₄, with x=5, 10, 20 and 30 mol.% was prepared. The optical absorption, ac and dc conductivities are the subject of the present work. The optical absorption indicates that the electronic transition is indirect and is associated with phonon assisted transition. The exponential dependence of the absorption coefficient as a function of the incident photon energy suggests that the Urbach rule is obeyed, and indicates the formation of a band tail. On the other hand, ac conductivity measurements are performed in the frequency range 0.1–100 kHz, and in the temperature range 300–600 K. The results of the electrical conductivity are discussed on the basis of electronic glass conduction models. Correlated narrow-band limit for random sites and single polaron hopping model are found to describe the experimental results effectively. The dielectric constant was correlated to the optical band gap and a satisfactory relation was found. It was also possible to calculate the thermochromic properties from independent ac and dc measurements, and it was possible to evaluate the optical gap at 0 K by extrapolation.     

Diffusion of Na in sodium borate glasses

Diffusion of ²²Na in ion-conducting xNa₂O·(1−x)B₂O₃ glasses (x=0.2 and 0.3) was investigated under standard conditions and under high pressure employing the radiotracer sectioning method. A slight decrease of the diffusion coefficients with increasing time of diffusion annealing is observed and attributed to a structural relaxation of the glass network. The temperature dependence of diffusion was measured below and also in a small temperature range above the glass transition temperature (T_G). Below T_G the diffusion coefficients obey Arrhenius relations. Diffusion in the glass with x=0.3 is fast and associated with an activation enthalpy of 71 kJ mol⁻¹. The diffusion coefficients of the glass with x=0.2 are significantly smaller with an activation enthalpy of 112 kJ mol⁻¹. The activation volume ΔV of Na-diffusion in 0.3Na₂O·0.7B₂O₃ was determined from high pressure diffusion studies at 623 K. A value of 0.52 molar volume of the glass matrix was obtained. According to our knowledge this is the first measurement of an activation volume of diffusion in ion-conducting glasses. The present results will be discussed and compared with dc conductivity data for borate glasses and diffusion results for other oxide glasses reported in the literature.