Intensity-modulated fiber Bragg grating sensor system based on radio-frequency signal measurement

An intensity-modulated, fiber Bragg grating (FBG) sensor system based on radio-frequency (RF) signal measurement is presented. The RF signal is generated at a photodetector by two modulated optical signals reflected from the sensing FBG and a reference FBG. Wavelength shift of the sensing FBG changes intensity of the RF signal through changing the delay between the two optical signals, with temperature effect being compensated automatically by the reference FBG. It also exhibits important features including potentially high-speed measurement, low cost, and adjustable sensitivity. In the experiment, strain measurement with a maximum sensitivity of -0.34 microV/micro epsilon has been achieved.     

基于频移反馈腔的全光纤射频调制脉冲激光研究

射频调制的脉冲激光是激光雷达探测领域内的一项重要研究内容.根据声光斩波器的强度和频率调制特性,设计了基于频移反馈腔的全光纤射频调制脉冲激光.理论上,建立了基于频移反馈腔的激光外差相干理论模型,并进行了数值仿真.根据理论模型,实验上严格控制频移反馈腔的长度和声光斩波器触发信号的周期,在100 MHz的射频信号驱动下,产生了脉冲宽度110 ns、重复频率约20 kHz的具有最高700 MHz射频调制的脉冲激光(脉内调制激光);同时微调斩波周期可以实现脉冲前沿或后沿的多样性射频调制.通过改变反馈腔内光纤放大器的输出功率实现了射频调制深度的连续可调,最高达到了0.67.     

High-efficiency hybrid brillouin/ytterbium fiber laser

A high-efficiency hybrid Brillouin/ytterbium fiber laser (BYFL) is demonstrated using a 41.5-cm-longhighly ytterbium-doped fiber and a 10-m-long single-mode optical fiber. The BYFL operates at 1 052.92nm, and the difference between it and the Brillouin pump (BP) wavelength matches the expected stimulated Brillouin scattering (SBS) Stokes shift. Its output power reaches 70.1 mW, which is more than seven times higher than the seeded BP power. The BYFL has an optical signal-to-noise ratio that is greater than 65 dB and has many potential applications, such as in controllable optical delay lines, sensing, and RF photonics.     

Radio frequency interrogated actively mode-locked fiber ring laser for sensing application

This paper proposes an actively mode-locked fiber ring laser for sensing applications. Mode-locking of the laser is achieved by driving an electro-optic amplitude modulator at an RF corresponding to the fundamental beat frequency between the longitudinal modes. The change of the cavity length produces a frequency comb around the beat frequencies. The frequency separation of the comb is found to be linearly proportional to the cavity length change. The sensing mechanism of the device is shown. Temperature measurement is demonstrated using the proposed actively mode-locked fiber ring laser.     

布里渊动态光栅原理及其在光纤传感中的应用

自从2007年布里渊动态光栅被首次提出用于实现光存储以来,该技术得到了国际上的广泛关注和研究.布里渊动态光栅本质上是由相干声波场激发的折射率光栅,一般情况下两束抽运光(频率差等于光纤的布里渊频移)以相同的偏振态从光纤两端注入到光纤中,通过受激布里渊散射效应激发出相干声波场,即形成布里渊动态光栅.光纤布里渊动态光栅因具有全光产生、参数灵活可控的优点,已被广泛研究应用于光纤传感、光纤特性表征、光存储、全光信号处理、微波光子学和高精度光谱分析等.本文分析布里渊动态光栅产生和探测原理,重点探讨在高性能分布式光纤传感上的应用,这些应用包括高灵敏度温度和应变分布式传感、温度和应变同时解调、分布式横向压力传感、分布式静压力(气压或液压)传感、高空间分辨率分布式传感和高精度光谱分析.     

Impact of interferometer delay time on the performance of ODSB-SC RoF system with wavelength interleaving

In this paper, we investigate the impact of interferometer delay time in a 5 Gb/s optical double sideband-suppressed carrier (ODSB-SC) RoF system transmitting two wavelength interleaved radio frequency (RF) signals at 10 and 15 GHz over an optical fiber. Here, an optical Mach–Zehnder modulator is used for both optical carrier suppression and signal modulation. At the receiver, delay interferometer is used for the separation of RF frequency signals. We analyze the performance of the RoF system by varying the value of delay time of interferometer from 0.02 to 0.14 ns. The result shows that the RoF system performance is optimum for the time delay of 0.1 ns. Further, the optical spectrums, RF spectrums and eye diagrams of two interleaved RF signals have been compared.     

Characterization of ROF signal based on cascaded optical carrier suppression modulation technique

The paper experimentally demonstrated the optical frequency quadrupling microwave signal generation, a 4 GHz radio frequency (RF) signals up-conversion to 16 GHz in a radio over fiber (ROF) link, using twice optical carrier suppression modulation. The RF signal was mixed with 1.25 Gbps NRZ-OOK data firstly and then modulated by two cascaded single-electrode optical intensity modulators. The obtained 1.25 Gbps/16 GHz ROF signal was transmitted and characterized in the optical fiber link. At BER of 10^?9, low power penalty of 1.0 and 1.4 dB were obtained over a fiber link with a transmission distance of 25 and 50 km.     

基于光子晶体光纤中受激布里渊散射的光载波抑制

设计了一种基于光子晶体光纤中受激布里渊散射的载波滤波器.该滤波器利用两个环形器和一段光子晶体光纤构成了一个环形腔,这种腔结构有效地降低了光纤中受激布里渊散射的阈值.理论分析了光子晶体光纤载波滤波器对提高光调制深度和射频增益的影响.利用25 m的高非线性光子晶体光纤作为受激布里渊增益介质,当入射载波功率为70 mW时,微波光子信号的射频增益为5.38 dB,实验结果与理论计算相吻合.     

Optical Microwave and Millimeter Generation by Using Birefringent Fiber FP Cavity with Pulse Laser Injection

A novel optical microwave and millimeter generation by using single mode fiber FP cavity (SMFFPC) with pulse laser injection is proposed and experimentally demonstrated. The frequency of output signal is determined by the birefringence degree of the SMFFPC, a general relationship between output signal frequency of SMFFPC and birefringence degree of single mode fiber is derived. The proof of concept device consists of a light source, a polarizer controller, a modulator, a RF generator, a single mode fiber Fabry-Perot cavity, a strain inspector, an erbium doped fiber amplifier, a filter, a polarizer, and a digital communication analyzer. The results demonstrate the new concept of optical microwave and millimeter generation and the technical feasibility.     

SOA-fiber ring laser and its application to electric field sensing in frequency domain

We have developed a novel optical fiber ring laser using a semiconductor optical amplifier (SOA) as the gain medium, and taking advantage of polarization anisotropy of its gain. The laser can control the oscillation frequency difference between two counterpropagating lights by incorporating a birefringent medium into the ring resonator. Since the frequency difference is proportional to the birefringence, it can be measured to detect the beat frequency generated by combining two counterpropagating lights and the laser can be applied to an optical fiber sensor whose detecting signal is in frequency domain. Electric field sensor was demonstrated with a lithium niobate crystal as a sensing probe.     

Passive and temporally continuous optical spectral analyzer of RF signals via wavelength coding

A novel approach realizing an optical spectrum analyzer for photonic detection of an unknown RF carrier signals is presented. The described module may be part of an electronic warfare system in which detection of a narrow band RF signal is required. Moreover, The RF signal is characterized by an unknown time varying carrier frequency embedded in wide band noise. The system uses a passive, fiber based photonic configuration. It allows the spectrum mapping of an incoming electronic RF signal modulated on an optical carrier. The spectral analyzer configuration uses a finite impulse response (FIR) filter that is realized by two different optical paths of parallel fibers which generate a spectral notch filter. Hence, a wavelength coding is realized by chromatic dispersion such that each wavelength is filtered by a different FIR filter. Therefore, the energy at a WDM demux output channels is actually proportional to the spectrum of the input RF signal. This spectral mapping is obtained without lose of temporal RF information.     

分立式与分布式光纤传感关键技术研究进展

光纤传感技术已广泛应用于航空航天、石油化工、电子电力、土木工程、生物医药等领域,其技术形式主要体现为分立式和分布式.分立式光纤传感技术利用光纤敏感器件作为传感器来感知被测参量的变化,光纤作为光信号的传输通道连接光纤传感器及后端的解调装置;分布式光纤传感系统基于光纤瑞利散射、拉曼散射或布里渊散射等光学效应,利用光纤本身作为传感器,可对沿途的光信号进行大范围、长距离传感.本文介绍了分立式与分布式光纤传感中主要关键技术的研究进展,并对未来的研究和发展方向进行了探讨.     

A novel frequency sextupling scheme for optical mm-wave generation utilizing an integrated dual-parallel Mach-Zehnder modulator

A novel scheme is proposed for frequency sextupling mm-wave generation based on a laser and an integrated dual-parallel Mach-Zehnder modulator (MZM) without optical filter. Theoretical analysis is presented to suppress the undesired optical sidebands for the high quality generation of frequency sextupling mm-wave signal. The performance of the proposed scheme is evaluated by simulations. Utilizing the integrated MZM consisted of two sub-MZMs with extinction ratio of 30 dB, the optical sideband suppression ratio (OSSR) is as high as 29.9 dB and the radio frequency spurious suppression ratio (RFSSR) exceeds 24 dB without any optical or electrical filter. The impact of the nonideal RF driven voltage and phase difference of RF driven signal applied to two sub-MZMs of the integrated MZM on OSSR and RFSSR is discussed and analyzed. After transmission over fiber, the generated optical mm-wave signal demonstrates good performance. Furthermore, the performance of two cases for the proposed scheme is also compared.     

Generation of linearized optical single sideband signal for broadband radio over fiber systems

We propose a new scheme to generate broadband linearized optical single-sideband （OSSB） signal for radio over fiber systems. By using an unbalanced dual parallel Mach-zehnder modulator （DPMZM） followed by optical filtering, a linearized OSSB signal is obtained. With coherent detection, radio frequency （RF） signal can be recovered with simultaneously suppressed second-order distortion and third-order intermodulation. This scheme can be used to realize broadband systems with wide dynamic range.     

基于拉曼光谱散射的新型分布式光纤温度传感器及应用

介绍了分布式光纤拉曼温度传感器(DTS)的基本原理、发展趋势和工程应用研究状况,研究了分布式光纤拉曼温度传感器的关键技术,全面提升了DTS的性能。将拉曼放大技术应用于DTS系统,用拉曼增益部分抵偿光纤的传输损耗,使系统的传感长度达到50 km;对脉冲激光器进行211位循环编码,在接收时采用相关运算解调,显著提高系统的信噪比,使测温不确定度达到1 ℃;采用双波长自校正技术提高了系统的空间分辨率,达到2 m;在DTS系统中嵌入光开关,使测温通道成倍扩展,有效延伸了传感光纤的总长度,组成光纤传感网络。     

SOA-based fiber ring laser use in a photonic radio-frequency phase shifter

This investigation demonstrates the feasibility of a semiconductor optical amplifier (SOA)—based fiber ring laser use in a photonic radio-frequency (RF) phase shifter. Experimental results indicate that a fiber ring laser can successfully replace an external pump laser in a photonic RF phase shifter. The RF phase shifter can be turned by adjusting the power of the fiber ring laser.     

Photonic vector signal generation employing a novel optical direct-detection in-phase/quadrature-phase upconversion

This work demonstrates the feasibility of the generation of an RF direct-detection vector signal using optical in-phase/quadrature-phase (I/Q) upconversion. The advantage of the proposed transmitter is that no electrical mixer is needed to generate the RF signal. Therefore, I/Q data of RF signals are processed at baseband at the transmitter, which is independent of the carrier frequency of the generated RF signal. A 10 Gb/s 16 quadrature amplitude modulation signal is experimentally demonstrated. Following transmission over a 50 km single-mode fiber, the power penalty is negligible. Moreover, I/Q imbalance of the proposed transmitter is studied and compensated by digital signal processing, which is both numerically and experimentally verified.     

Stimulated Brillouin scattering in highly birefringent microstructure fiber: experimental analysis

We report on an experimental analysis of stimulated Brillouin scattering (SBS) in a 20-m-long highly birefringent microstructure fiber for sensing applications. In particular, an experimental setup based on Brillouin optical frequency-domain analysis, operating at a wavelength of 1550 nm, has been employed in order to analyze the distribution of Brillouin frequency shift along the fiber, as well as to study the dependence of Brillouin frequency shift on optical polarization, temperature, and strain. Our results indicate that, for any fixed polarization, the fiber has a dual-peaked Brillouin spectrum. A study about the origin of these two peaks is presented.     

Semiconductor Optical Amplifier (SOA)-Fiber Ring Laser for Sensor Application

A bi-directional fiber ring laser with a semiconductor optical amplifier has been developed in which a frequency difference between the counter-propagating oscillations is controlled by an introduced birefringent medium. With the material which causes the retardation change by a physical phenomenon to be measured, the laser in this study is applicable to a novel fiber sensor of which the sensing signal is obtained in a frequency domain.     

A full-duplex radio-over-fiber system using direct modulation laser to generate optical millimeter-wave and wavelength reuse for uplink connection

In this paper, we present a full-duplex radio-over-fiber system incorporating both optical millimeter-wave (mm-wave) generation and wavelength reuse for uplink connection. The optical double sidebands (DSB) signal is generated by using only one inexpensive broadband direct modulation laser (DML), to which a mixing RF signal is applied. An optical interleaver is then used to separate the first-order optical sidebands from the optical carrier of optical DSB signal. The separated first-order optical sidebands are beat to generate mm-wave signal that has double the frequency of the RF drive signal, while the separated optical carrier is reused as light source to remodulate uplink signal. Both detailed theoretical analysis and experiments to demonstrate the feasibility of the proposed system are presented. Experiment result shows that the bidirectional 2.5 Gb/s data can be successfully transmitted over 40 km standard single-mode fiber (SSMF) with less than 2 dB power penalty.