Raman fiber distributed feedback lasers

We demonstrate fiber distributed feedback (DFB) lasers using Raman gain in two germanosilicate fibers. Our DFB cavities were 124 mm uniform fiber Bragg gratings with a π phase shift offset from the grating center. Our pump was at 1480 nm and the DFB lasers operated on a single longitudinal mode near 1584 nm. In a commercial Raman gain fiber, the maximum output power, linewidth, and threshold were 150 mW, 7.5 MHz, and 39 W, respectively. In a commercial highly nonlinear fiber, these figures improved to 350 mW, 4 MHz, and 4.3 W, respectively. In both lasers, more than 75% of pump power was transmitted, allowing for the possibility of substantial amplification in subsequent Raman gain fiber.     

高频调制大功率窄线宽分布反馈光纤激光器

研制了一种窄线宽光纤激光器.在有源相移光栅后加一段掺铒光纤,当用980 nm抽运光注入时,首先形成了分布反馈(DFB)光纤激光器,而残余抽运光将铒纤中铒离子从基态抽运到了激发态,对DFB激光实现了有效放大,实现了对残余抽运光的充分利用,节省了功耗、降低了成本;同时利用温控技术克服了DFB光纤激光器的温度敏感问题;将相移光栅黏贴于片状压电陶瓷(PZT)的表面实现了高频调制.实验研制的激光器的最高调制频率为2 kHz、输出功率为15.6 dBm,线宽为300 kHz. 关键词： 分布反馈光纤激光器 窄线宽 大功率 高频调制     

Corrugated neat thin-film conjugated polymer distributed-feedback lasers

Wave-guided thin-film distributed-feedback (DFB) polymer lasers are fabricated by spin coating a PPV-derived semiconducting polymer, thianthrene-DOO-PPV, onto oxidised silicon wafers with corrugated second-order periodic gratings. The gratings are written by reactive ion beam etching. Laser action is achieved by transverse pumping with picosecond laser pulses (wavelength 347.15 nm, duration 35 ps). The DFB-laser surface emission and edge emission are analysed. Outside the grating region the polymer film is used for comparative wave-guided travelling wave laser (amplified spontaneous emission (ASE)) studies. The pump pulse threshold energy density for wave-guided DFB-laser action (4–9 μJ cm^-2) is found to be approximately a factor of two lower than the threshold for wave-guided travelling wave laser action. The spectral width of the DFB laser (down to Δλ_DFB≈0.07 nm) is considerably narrower than that of the travelling wave laser (Δλ_TWL≈14 nm). The DFB-laser emission is highly linearly polarised transverse to the grating axis (TE mode). Only at high pump pulse energy densities does an additional weak TM mode build up. The surface-emitted DFB-laser radiation has a low divergence along the grating direction. For both the DFB lasers and the travelling wave lasers, gain saturation occurs at high excitation energy densities. Received: 7 January 2002 / Revised version: 15 February 2002 / Published online: 14 March 2002     

应力所致单偏振相移分布反馈光纤激光器

利用对相移分布反馈（DFB）光纤激光器的相移区施加一定的应力，使光栅的相移区产生双折射，得到了消光比为14dB的运行在1053nm的单偏振激光输出，并且由于光纤光栅的相移区偏离了光纤光栅的中心位置，使激光器的输出功率特性具有一定的方向选择性。     

Stable single frequency and single polarization DFB fiber lasers operated at 1053 nm

Stable single-frequency and single-polarization distributed-feedback (DFB) fiber laser was realized by giving a pressure on the phase shift region of the fiber grating. The output wavelength of the DFB fiber laser is 1053 nm. When the pump power of 980 nm laser diode is 100 and 254 mW, the output power can reach 8.3 and 37.1 mW and the polarization extinction ratio was 26 and 20 dB, respectively. After chopped by Acousto-optic modulator (0.3 Hz), the pulse peak value variance is 4.65%(peak to peak) and 1.098% (RMS) for 31 min.     

Single-frequency thulium-doped distributed-feedback fiber laser

We have successfully demonstrated a single-frequency distributed-feedback (DFB) thulium-doped silica fiber laser emitting at a wavelength of 1735 nm. The laser cavity is less than 5 cm long and is formed by intracore UV-written Bragg gratings with a phase shift. The laser is pumped at 790 nm from a Ti:sapphire laser and has a threshold pump power of 59 mW. The laser has a maximum output power of 1 mW in a single-frequency, single-polarization radiation mode and is tunable over a few nanometers. To the best of the authors' knowledge, this is the first report of a single-frequency DFB fiber laser that uses thulium as the amplifying medium. The lasing wavelength is the longest demonstrated with DFB fiber lasers and yet is among the shortest obtained for thulium-doped silica fiber lasers.     

All optical Flip-Flop based on a nonlinear DFB semiconductor laser: Theoretical study

A new design of an all optical Flip-Flop is proposed. It consists of a nonlinear distributed feedback (DFB) laser. The wave guiding layer of the DFB laser consists of linear grating section followed by a nonlinear one, and both sections are separated by a phase shift section. In the OFF-state, the real part of the refractive index in the wave guiding layer forms a Bragg grating. In the ON-state, it forms a Bragg grating with a phase shift section. Optical gain is achieved by current injection in the semiconductor active layer. Nonlinearity in the nonlinear layers of the semiconductor grating was achieved by direct absorption at the edge of the absorption band (Urbach tail). Numerical simulation shows that the device switches in a nanosecond time scale.     

Linewidth narrowing and polarization control of erbium-doped fiber laser by self-injection locking

A novel and simple self-injection locking (SIL) configuration of distributed feedback (DFB) fiber laser is presented. By injecting the feedback light into the cavity of the fiber laser, it can realize that the line-width can be narrowed by half compared with the same system without SIL. Meanwhile the stable single-polarization lasing is achieved and the degree of polarization is improved from 0.165 to 0.989. Then the self-pulsation behavior of the DFB fiber laser is investigated in the injection-locked and unlocked system respectively and the output power fluctuation is reduced from about 4 to 0.1 dBm by injection locking. And the power output characteristics of the DFB fiber laser are also researched by changing the pump current. With increasing the pump current from 30 to 275 mA, the output power of the DFB fiber laser increases linearly and the injection-locked output increases slightly more quickly than the unlocked output. The results have a great potential application in optical communication and high sensitive fiber sensors.     

Sampled grating distributed feedback (SG DFB) semiconductor laser diode

A laser diode was designed using a method called sampled grating (SG) distributed feedback (DFB), in which the couplings have been distributed in certain regions along the laser cavity (i.e., regions contain grating). These regions play a big role in pushing the main mode to propagate faster than the side mode by increasing the time delay between them. This delay is due to the empty regions (i.e., regions without grating) along the laser cavity. Neither a phase shift nor incomplete grating have been taken into account with the new structure. The theoretical model in the present work is based on the coupled-mode equations which have been solved numerically by the mean of transfer matrix method (TMM).     

A widely tunable hybrid brillouin-erbium fiber laser (BEFL) system

This paper presents a tunable hybrid brillouin-erbium fiber laser system with a maximum tuning range of more than 36.7 nm. The system was configured in a ring set-up with another fiber laser used as the brillouin pump at about 8 mW maximum launched power. Stable Stokes signals at an average of about 0.08 nm wavelength shift were observed across the tuning range. The dependency of the Stokes signal tuning range on the laser's spectral gain is also elaborated.     

输出功率稳定的二级喇曼光纤激光器特性

提出一种输出功率稳定的二级喇曼光纤激光器,从理论分析角度探讨了它的特性.结果表明：由于在抽运光的二级斯托克斯光频附近的自发辐射光的钳制作用,激光器的一级和二级输出功率几乎都不受抽运功率波动的影响,从而降低了抽运光低频相对强度噪音转移|激光器输出的一级和二级斯托克斯光功率都很稳定,并且通过调节激光器结构中的可变衰减器,可以有效控制一级、二级激光的输出功率以及它们的比值.这些特性表明该喇曼光纤激光器很适合于作为喇曼光纤放大器的抽运源.     

Solid-state dye laser with moiré gratings

We fabricated distributed-feedback (DFB) solid-state dye lasers with moiré gratings. We formed a moiré grating pattern by superimposing two grating patterns with a rotation angle. The moiré gratings were fabricated by an “etchless” process utilizing a two-beam interference method. The gratings were coated with solidified rhodamine-B. The five laser devices were pumped with the second harmonic generation of a Nd:YAG laser and we obtained narrow-banded laser oscillations at 590, 600, 610, 620, and 630 nm wavelength. Full widths at half maximum of laser spectra were less than 0.5 nm. The results indicated that a moiré fringe can function as a resonator of DFB solid-state dye lasers.     

Distributed feedback dye laser holographically induced in improved organic–inorganic photocurable nanocomposites

Distributed feedback (DFB) lasing in permanent volume transmission gratings formed in a laser dye-doped organic–inorganic nanocomposite has been investigated. DFB laser cavities were fabricated using one-step two-beam holographic exposure of Pyrromethene 567 (PM567) doped photopolymerizable acrylate monomers containing inorganic (LaPO₄) nanoparticles. Compared to the formulation previously utilized, the material composition presented provides longer lifetime of the laser. Spectral and polarization properties, input–output and stability characteristics of the laser output have been investigated by varying the material composition and the patterning parameters. DFB lasing emission of the second and the third diffraction orders has been demonstrated. The spectral linewidth of ∼0.08 nm has been observed at a pump energy threshold of about 0.2 μJ/pulse for the second-order DFB lasing when pumped with 532 nm 500 ps laser pulses. Spectral tuning of the lasing output over ∼56 and ∼7 nm was obtained by varying the grating period and the content of inorganic nanoparticles in the polymer matrix, respectively.     

High-power Tm-doped fiber distributed-feedback laser at 1943 nm

We report on high-power operation of a fiber distributed-feedback (DFB) laser fabricated from Tm-doped photosensitive alumino-silicate fiber and in-band pumped by an Er/Yb fiber laser at 1565 nm. The fiber DFB laser yielded up to 875 mW of single-ended output at 1943 nm on two orthogonally polarized modes for 3.5 W of absorbed pump power. Further scaling of the DFB laser output power was achieved with the aid of a simple Tm-doped fiber amplifier stage spliced directly to the DFB fiber without the need of an optical isolator. The maximum output power from the DFB laser and fiber amplifier was >3 W for a combined absorbed pump power of 8.1 W. The influence of thermal loading, owing to quantum defect heating in the Tm-doped core, on the output power and longitudinal mode behavior is discussed, and the prospects for further improvement in performance are considered.     

Design of surface emitting distributed feedback quantum cascade laser with single-lobe far-field pattern and high outcoupling efficiency

A 7.8-$\mu $m surface emitting second-order distributed feedback quantum cascade laser (DFB QCL) structure with metallized surface grating is studied. The modal property of this structure is described by utilizing coupled-mode theory where the coupling coefficients are derived from exact Floquet--Bloch solutions of infinite periodic structure. Based on this theory, the influence of waveguide structure and grating topography as well as device length on the laser performance is numerically investigated. The optimized surface emitting second-order DFB QCL structure design exhibits a high surface outcoupling efficiency of 22{\%} and a low threshold gain of 10~cm$^{ - 1}$. Using a {$\pi $} phase-shift in the centre of the grating, a high-quality single-lobe far-field radiation pattern is obtained.     

Vertically emitting, dye-doped polymer laser in the green (λ ∼ 536 nm) with a second order distributed feedback grating fabricated by replica molding

Lasing in the green from a distributed feedback (DFB) structure, based upon a second order grating fabricated by replica molding in a dye-doped UV curable polymer, has been demonstrated. For a Bragg grating having a periodicity and depth of 360 ± 2 nm and 78 ± 5 nm, respectively, a coumarin 540-polymer laser operates at 535.6 nm, which is in agreement with calculations of the photonic band diagram for the structure. The fabricated laser exhibits a linewidth of 0.15 nm, a threshold pump fluence of ∼0.7 mJ cm⁻² at 355 nm, and a slope efficiency of ∼14%. Incorporation of the dye gain medium into a one- (or two-) dimensional photonic crystal and fabrication of the grating by replica molding at room temperature provides an inexpensive approach to fabricating polymer-based DFB lasers on flexible substrates of large area.     

Suppression of pump-to-Stokes relative intensity noise transfer in Raman fiber laser by injection of modulated signal

A feasible approach is theoretically demonstrated that suppresses the relative intensity noise (RIN) transfer from pump sources to the proposed Raman fiber laser (RFL) output at the first-order Stokes line. The technique is accomplished by injecting a modulated signal at second-order Stokes shift from the pump wavelength according to the monitored RFL output, which indirectly consumes the pump power fluctuations and results in suppression of the RIN transfer to the RFL output. With the RFL used as a pump source for co-pumped Raman fiber amplifiers, further calculation results show that the Q-factor penalty due to RIN transfer can be dramatically reduced.     

激光烧蚀制备分布反馈式有机激光器件

采用激光烧蚀的方法结合激光全息技术,直接在高分子聚合物MEH-PPV薄膜表面烧蚀光栅结构,制备了分布反馈式有机激光器。这一方法具有工艺简单、光栅参数的可控性和重复性好等优点。器件MEH-PPV的膜厚是400 nm。利用波长为355 nm的Nd-YAG纳秒激光器进行单脉冲烧蚀,获得的光栅周期和光栅高度分别为370 nm和 100 nm。利用飞秒激光放大器作为泵浦源激射DFB激光器件,得到激射阈值约为182 μJ·cm^-2·pulse^-1,光谱的波峰约在609 nm处,半高宽为4.2 nm。通过改变两光束的夹角获得了周期为360, 370, 380, 390 nm的光栅,它们对应的激光波峰分别为602.91, 609.24, 613.26, 619.01 nm。     

Pump-Induced Lasing Wavelength Shift in Er/Yb Codoped Fiber Grating Lasers

１ＩｎｔｒｏｄｕｃｔｉｏｎＥｒｂｉｕｍ／Ｙｔｅｒｂｉｕｍｃｏｄｏｐｅｄｆｉｂｅｒｓａｒｅｉｄｅａｌｇａｉｎｍｅｄｉａｆｏｒｃｏｎｓｔｒｕｃｔｉｎｇｓｉｎｇｌｅｆｒｅｑｕｅｎｃｙｆｉｂｅｒｌａｓｅｒｓ．Ｔｈｅｉｒｂｒｏａｄａｂｓｏｒｐｔｉｏｎｂａｎｄ...     

利用双色激光感生光栅光谱法测定^127I的核自旋

本文利用ＮｄＹＡＧ激光倍频光５３２ｎｍ激光分成强度大致相等的两束激光作为泵浦光以２．７３°交叉于碘分子样品室中，两束泵浦光发生干涉在碘分子中选择激发形成了空间正弦分布的激光态分子光栅和基态耗尽型光栅。另一束窄线宽染料激光作为探索光射入到激光感生光栅上，沿着布拉格衍射的方向接收信号光。利用泵浦共振为３２－０Ｒ（５５），探索共振为１３－０Ｐ（５５），Ｒ（５５）和泵浦共振为３２－０Ｐ（５２），探索共振为１３－０Ｐ（５２），Ｒ（５２）的碘分子双色激光感生光栅光谱谱线强度测定了１２７Ｉ的核自旋，测定值为５／２。