国产光纤实现同带抽运3000W激光输出

同带抽运是目前实现高功率光纤激光器的有效手段.本文基于同带抽运方式,以国产25/250μm掺镱双包层光纤为增益光纤,构建了全光纤化的主控振荡器功率放大器.实验中采用的国产光纤是中国电子科技集团公司第四十六研究所采用化学气相沉积结合气相-液相复合掺杂工艺制备的,其Yb~(3+)离子的分布更均匀,吸收截面更大,吸收系数更高.实验中,在种子光功率为67.8 W、抽运总功率为3511 W的条件下,实现了3079 W的激光输出,斜效率为85.9%,光束质量M~2约为2.14,3dB带宽为1.4nm,这是目前基于国产光纤同带抽运方式实现的最高功率.理论和实验结果表明国产光纤制备技术不断成熟,已经具备承受高功率输出的能力.继续提高抽运功率,优化增益光纤长度,改良散热方式,国产光纤有望实现更高功率的激光输出.     

976 nm激光抽运二氧化硅微球级联拉曼散射激光的研究

利用电极放电产生的电弧高温熔融二氧化硅单锥细纤, 熔融的二氧化硅在表面张力作用下形成表面光滑的微球, 完成高品质因子微球腔的制备. 将976 nm激光通过锥光纤以倏逝场方式高效耦合入微球, 研究具有高能量密度回廊模的微球腔中的三阶非线性现象——受激拉曼散射现象. 在实验中测得了六级级联的拉曼散射激光, 各级拉曼散射激光分别测得单纵模或多纵模; 在抽运光功率不少于582.6 μW时, 测得位于1200 nm附近的拉曼散射激光; 当抽运光功率为3.014 mW时, 测得位于1287.04 nm附近的第六级拉曼散射激光. 关键词： 微球腔 锥光纤 高品质因子 拉曼散射激光     

18 W single-stage single-frequency acoustically tailored Raman fiber amplifier

A single-mode polarization-maintaining fiber doped to increase the Raman gain while suppressing stimulated Brillouin scattering (SBS) was utilized in a single-stage counter-pumped Raman fiber amplifier. The SBS suppression was achieved through the acoustic tailoring of the core. A pump probe experiment was conducted to characterize the Brillouin gain and indicated the existence of multiple Brillouin peaks. When the amplifier was seeded with approximately 15 mW of 1178 nm light, 11.5 W of cw output power was obtained with a linewidth ≤2 MHz. The application of a thermal gradient to further mitigate the SBS process increased the output power to 18 W, thus providing a net amplifier gain >30 dB.     

窄线宽1064 nm光纤激光泵浦高效率中红外3.8μm MgO:PPLN光参量振荡器

采用放大1064 nm掺镱光纤激光器作为泵浦源,实现了中红外3.8μm MgO:PPLN光参量振荡(OPO)激光输出。在泵浦源中,采用分布式反馈激光器(DFB)作为种子源来实现光纤激光窄线宽的调制,实现线宽2.5 nm到0.1 nm的压缩,最大平均输出功率可达40 W。进一步对不同泵浦线宽条件下中红外3.8μm MgO:PPLN OPO激光进行研究,最终在泵浦功率为18.1 W、线宽为0.1 nm、重频为1 MHz、脉宽为2 ns时,获得了最高平均输出功率为2.06 W的3822.5 nm激光输出,光-光转换效率为11.38%,光束质量为M2=2.34,提高了窄线宽泵浦对中红外MgO:PPLN OPO激光输出效率。     

High-power Tm-doped fiber distributed-feedback laser at 1943 nm

We report on high-power operation of a fiber distributed-feedback (DFB) laser fabricated from Tm-doped photosensitive alumino-silicate fiber and in-band pumped by an Er/Yb fiber laser at 1565 nm. The fiber DFB laser yielded up to 875 mW of single-ended output at 1943 nm on two orthogonally polarized modes for 3.5 W of absorbed pump power. Further scaling of the DFB laser output power was achieved with the aid of a simple Tm-doped fiber amplifier stage spliced directly to the DFB fiber without the need of an optical isolator. The maximum output power from the DFB laser and fiber amplifier was >3 W for a combined absorbed pump power of 8.1 W. The influence of thermal loading, owing to quantum defect heating in the Tm-doped core, on the output power and longitudinal mode behavior is discussed, and the prospects for further improvement in performance are considered.     

High-power linearly-polarized tunable Raman fiber laser

In this study, we demonstrate an all-fiber high-power linearly-polarized tunable Raman fiber laser system. An inhouse high-power tunable fiber laser was employed as the pump source. A fiber loop mirror(FLM) serving as a high reflectivity mirror and a flat-cut endface serving as an output coupler were adopted to provide broadband feedback. A piece of 59-m commercial passive fiber was used as the Raman gain medium. The Raman laser had a 27.6 nm tuning range from1112 nm to 1139.6 nm and a maximum output power of 125.3 W, which corresponds to a conversion efficiency of 79.4%.The polarization extinction ratio(PER) at all operational wavelengths was measured to be over 21 d B. To the best of our knowledge, this is the first report on a hundred-watt level linearly-polarized tunable Raman fiber laser.     

1410 nm波段分布式光纤拉曼增益放大器的研究

讨论了分布式光纤拉曼增益放大器的工作原理,采用1320nm固体激光器作为抽运源,获得了1410nm波段附近的光放大,在单模GI光纤长度为23km时,初步研究了拉曼放大器增益与光纤作用长度的关系,抽运脉冲峰值功率分别为50W、30W时,光纤的有效作用长度分别为15．5km和10.5km;研究了在不同的光纤有效作用长度时,拉曼放大器增益与抽运功率的关系;从光纤拉曼光谱图估算了光纤拉曼放大器的光谱宽度为50nm或250cm^-1。     

Raman fiber laser improvement by using Yb3+-doped fiber

We report here the efficiency improvement in a fiber Raman laser by splicing to it short pieces of 10000-ppm Yb³⁺-doped fibers. The amplified spontaneous emission produced by the doped fiber started the stimulated Raman scattering earlier than the spontaneous scattering in the 350-m silica-fiber cavity. In the best case, when splicing to the cavity 127 cm of doped fiber, the pump threshold decreased from 2.9 down to 1.27 W, representing a 56% improvement. This power was close to the theoretical minimum of 1.25 W for very long fibers. The second stokes signal (1175 nm) was only present when the doped fibers were inserted. At 4-W pump, the non-doped cavity delivered 2 W of first stokes signal (1117 nm) that represent a 50% efficiency compared to ～3 W delivered (～75%) when a 34-cm doped fiber was inserted. This improvement is intended to reduce the cost of fiber Raman lasers because less powerful sources or shorter fibers are necessary to produce more stokes components.     

Single-frequency thulium-doped distributed-feedback fiber laser

We have successfully demonstrated a single-frequency distributed-feedback (DFB) thulium-doped silica fiber laser emitting at a wavelength of 1735 nm. The laser cavity is less than 5 cm long and is formed by intracore UV-written Bragg gratings with a phase shift. The laser is pumped at 790 nm from a Ti:sapphire laser and has a threshold pump power of 59 mW. The laser has a maximum output power of 1 mW in a single-frequency, single-polarization radiation mode and is tunable over a few nanometers. To the best of the authors' knowledge, this is the first report of a single-frequency DFB fiber laser that uses thulium as the amplifying medium. The lasing wavelength is the longest demonstrated with DFB fiber lasers and yet is among the shortest obtained for thulium-doped silica fiber lasers.     

窄线宽纳秒脉冲光纤拉曼放大器的理论模型和数值分析

窄线宽纳秒脉冲光纤拉曼放大器在非线性频率变换、遥感探测和量子信息等领域有广泛的应用前景.综合考虑受激拉曼散射(stimulated Raman scattering,SRS)、受激布里渊散射(stimulated Brillouin scattering,SBS)、自相位调制(self-phase modulation)和交叉相位调制(cross-phase modulation)等非线性效应,建立了窄线宽纳秒脉冲光纤拉曼放大器的非线性动力学模型.仿真分析了放大器中脉冲激光的时频演化特性,对比研究了抽运脉冲宽度、光纤长度和信号光功率等因素对放大器性能的影响.研究发现,上述因素会影响放大器的SRS阈值、SBS阈值、输出激光线宽、激光转换效率等.例如,当脉冲宽度为800 ns时,SBS随着抽运功率的增加而发生,限制了激光功率的提升;减短抽运脉宽可以抑制SBS,但是输出激光的线宽易于展宽到数百MHz以上;增加光纤长度可以获得更低的SRS阈值和更高的转换效率,但是SBS效应和光谱展宽程度也随之增强.系统搭建中需要平衡各非线性效应,选择合适的系统参数.研究内容可以为窄线宽纳秒脉冲光纤拉曼放大器的设计搭建提供参考.     

双重复频率锁模Yb:YAG陶瓷激光器

近年来,双重复频率锁模激光器在诸如双光梳光谱和异步光学采样等应用领域吸引了广泛关注.基于单一激光腔的双梳系统能大大降低成本,简化系统结构,且性能优异.双重复频率锁模激光器为发展紧凑型和实用型双梳装置开辟了道路.本文报道了一种可用作双光梳光谱系统光源的双重复频率锁模Yb:YAG陶瓷激光器.该激光器基于半导体可饱和吸收镜锁模技术,采用双通道抽运结构,利用新型非水基流延成型制备的Yb:YAG透明陶瓷,在单一的五镜腔中,当吸收抽运光功率为5.6 W时,实现了自启动、稳定运转的双重复频率锁模脉冲Pulse1和Pulse2,其重复频率分别为448.918和448.923 MHz,重复频率差为5 kHz.在吸收抽运功率为7 W时,得到最大的总平均输出功率170 mW,其中Pulse1和Pulse2的功率分别为89和81 mW,相应的光谱宽度分别为1和1.16 nm.性能相似的双重复频率脉冲彼此间保持了良好的相干性,实验结果证明了双通道抽运在双重复频率锁模激光器应用中的可行性,此种新型双重复频率激光器在双光梳光谱和测距等领域具有较好的应用潜力.     

Single-mode 212 W tapered fiber laser pumped by a low-brightness source

With a tapered double-clad all-glass ytterbium fiber as a gain medium, a maximum output power of over 200 W at 1079 nm and a slope efficiency of over 70% were demonstrated. The tapered double-clad fiber concept allows for using low-brightness diode bars and results in cost-effective and efficient high-power fiber lasers. The adiabatic conical fiber gain waveguide combines improved pump absorption owing to enhanced mode mixing in the pump cladding, low-noise single fundamental mode operation with M(2)< or =1.02, and strong potential for significant power scaling.     

Highly stable, passively mode-locked fiber laser with low pump power for subpicosecond pulse generation

We present the design of highly stable, passively mode-locked fiber lasers which are based on a simple configuration and require a low pump power for the generation of optical pulses with subpicosecond pulsewidth. Our designed fiber laser uses a semiconductor saturable absorber mirror to realize the self-starting, passive mode locking at a low pump power of 29 mW, with which a stable optical pulse train is obtained at the fundamental repetition rate of 52.5 MHz and the central wavelength of 1557 nm. The output mode-locked optical pulses have a pulsewidth of 881 fs and an average output power of 1.78 mW, respectively.     

Fluoride glass Raman fiber laser at 2185 nm

We report on the first Raman laser based on a fluoride glass optical fiber. The Raman fiber laser was pumped by a 9.6?WTm3+:silica CW fiber laser operating at a wavelength of 1940?nm. A maximum output power of 580?mW was measured at 2185.1?nm, corresponding to a frequency shift of 579?cm(-1) (17.37?THz). We observed a threshold power of 3.8?W and a low power slope efficiency of 29% with respect to the launched pump power. Using those results and the known fiber parameters, we estimated a Raman gain peak value of 3.52*10(-14)?m/W, which is lower than the previously reported values.     

高功率半导体激光泵浦源研究进展

高功率半导体激光器是固体激光器和光纤激光器的主要泵浦源。激光泵浦源性能的大幅提升直接促进了固体激光器、光纤激光器等激光器的发展。主要介绍了8xx nm和9xx nm系列半导体激光泵浦源的最新研究进展,8xx nm单管输出功率已达18.8 W@95μm,巴条输出功率已达1.8 kW(QCW),9xx nm单管输出功率已达35 W@100μm,巴条输出功率已达1.98 kW(QCW)。谱宽<1 nm的窄谱宽半导体激光器输出功率可达14 W。展望了未来半导体激光器泵浦源的发展趋势。     

被动锁模Yb3+光纤环形腔激光器的研究

 采用974 nm半导体激光器作为泵浦源，超高掺杂Yb³⁺光纤作为增益介质，利用光纤的非线性偏振旋转效应，得到稳定的ps量级锁模光脉冲。泵浦功率220 mW时，激光器锁模阈值功率150 mW，输出功率26 mW，锁模光脉冲中心波长1 046 nm，3 dB带宽6.01 nm，20 dB带宽16 nm，脉宽22 ps，重复频率20 MHz。与同类光纤激光器相比，该激光器输出功率高，具有更好的稳定性。     

Mode-locked pulse generation from an all-FMF ring laser cavity

Experimental generation of stable mode-locked pulses and cylindrical vector beams(CVBs), from an all fewmode fiber(FMF) ring laser is first reported, to the best of our knowledge. In this laser, a section of few-mode erbium-doped fiber(FM-EDF) is used as the gain medium. The FM-EDF is pumped by 976 nm laser with LP11 mode, which is simultaneously converted and multiplexed through a homemade hybrid device, i.e., wavelength division multiplexing-mode selection coupler(WDM-MSC). All the components in our experiment are connected using FMF. The resulted CVB pulses have a spectral width of 0.33 nm with a repetition rate of 30.58 MHz under the pump power of 340 m W. Moreover, both azimuthally and radially polarized CVBs were achieved with a high purity of 95%. This mode-locked CVB fiber laser with an all FMF configuration opens the way to manipulate the transverse mode in mode-locked fiber lasers.     

Comparison of Brillouin-Raman comb fiber laser in two different configurations

The properties of a Brillouin-Raman comb fiber laser are compared for two different configurations: co-propagating and counter-propagating Raman pump. The optical spectrum is compared for changing the Raman pump power and the power or the wavelength of seed laser. A Brillouin-Raman comb with 400 linewidth lasers in a flat-amplitude bandwidth of 32 nm between 1538 and 1570 nm, with an average optical power 20 dB above the nearby frequencies was generated. The lasers in the comb had an OSNR of 20 dB and a wavelength spacing of 0.08 nm. The results for the counter-propagating configuration were observed to have better quality.     

高频调制大功率窄线宽分布反馈光纤激光器

研制了一种窄线宽光纤激光器.在有源相移光栅后加一段掺铒光纤,当用980 nm抽运光注入时,首先形成了分布反馈(DFB)光纤激光器,而残余抽运光将铒纤中铒离子从基态抽运到了激发态,对DFB激光实现了有效放大,实现了对残余抽运光的充分利用,节省了功耗、降低了成本;同时利用温控技术克服了DFB光纤激光器的温度敏感问题;将相移光栅黏贴于片状压电陶瓷(PZT)的表面实现了高频调制.实验研制的激光器的最高调制频率为2 kHz、输出功率为15.6 dBm,线宽为300 kHz. 关键词： 分布反馈光纤激光器 窄线宽 大功率 高频调制     

Fourth-order cascaded Raman shift in AsSe chalcogenide suspended-core fiber pumped at 2 μm

Cascaded Raman wavelength shifting up to the fourth order ranging from 2092 to 2450 nm is demonstrated using a nanosecond pump at 1995 nm in a low-loss As(38)Se(62) suspended-core microstructured fiber. These four Stokes shifts are obtained with a low peak power of 11 W, and only 3 W are required to obtain three shifts. The Raman gain coefficient for the fiber is estimated to (1.6±0.5)×10(-11) m/W at 1995 nm. The positions and the amplitudes of the Raman peaks are well reproduced by the numerical simulations of the nonlinear propagation.