LS301快中子探测器的效率刻度

主要介绍了利用252Cf标准裂变中子能谱刻度快脉冲LS301型液闪中子探测器的探测效率的实验方法和结果, 简要介绍了实验数据的处理过程, 得到了阈值分别为0.5, 0.7, 1.0和1.6 MeV, 以及中子能量在10 MeV以下的探测器效率, 并对测量结果进行了误差分析。同时为了检验实验结果的准确性, 将实验结果与理论计算结果进行比较, 两者在不确定度范围内符合得很好。Neutron detection efficiency of LS301 fast neutron detector was calibrated by measuring the neutron energy spectrum of 252Cf source, which has a standard fission neutron spectrum. A low mass, fast ionization chamber is used as the fission fragments detector in the time of flight(TOF) spectrometer and afforded the start signal of neutron flight. The stop signal was offered by the anode of LS301. A measured TOF spectrum was turned to the neutron energy spectrum which will be compared with the standard one. Consequently, the fast neutron detection efficiency of LS301 was obtained. Calibration procedures of experimental and data processing was given. Relative detection efficiencies were obtained separately for threshold settings of 0.5, 0.7, 1.0 and 1.6 MeV for neutron energies under 10 MeV. Experimental results accorded with theoretical efficiency curves which were calculated with the Monte Carlo code NEFF50.     

用于中子测量的俘获探测器研究

为了在弱中子场和有限小空间内测量绝对裂变率, 制作了俘获探测器, 研究了俘获探测器的性能。 介绍了用于中子测量的俘获探测器和铅屏蔽室, 以及该探测器系统在特定条件下测量裂变反应率的结果, 并与裂变室测量结果进行了比较。 探讨了铅屏蔽室大小对测量结果的影响。 To detect the absolute neutron flux in a weak neutron field and restricted space, the fission fragment trapping detector was fabricated and the properties of the detector were studied. In this paper, the detector and shielding chamber used in neutron detection were described and the experimental measurements of the fission rate in specific condition were performed with the detection system and the result has been compared with that obtained by fission chamber. The influence of the shielding chamber on the measured results was analyzed.     

用于快中子探测的裂变电离室实验及模拟结果比较(英文)

本文报道了一种用于快中子测量的裂变电离室的实验及模拟结果对比,该电离室的裂变材料为238U,分别电镀在电离室的阳极和阴极。裂变电离室通常有三种工作模式:脉冲模式、均方电压模式和电流模式,从而在大动态范围内实现中子注量测量。我们利用252Cf中子源对工作在脉冲模式的裂变电离室效率进行了测量,同时为了评估均方电压模式和电流模式,测量了裂变电离室在不同气压下的脉冲幅度,并通过Geant4蒙特卡罗软件对裂变电离室的脉冲幅度进行了模拟。模拟可以解释实验结果,当工作气压是2.64×105 Pa时探测效率最高[（4.30±0.7）×10-7],且裂变碎片能谱清晰,表明裂变电离室可以工作在不同模式下。     

用于裂变碎片质量测量的MCP和Au-Si SBD飞行时间探测系统

为了能很好地鉴别碎片质量,建立一个好的飞行时间测量方法是十分必要的。阐述了建立用于裂变碎片质量测量的微通道板（MCP）和金硅面垒探测器（SBD）飞行时间探测系统。对于80 μg/cm2厚的碳膜,241Am的α粒子的探测效率约为39%,252Cf（sf）裂变碎片的探测效率约为98%。在动能为78 MeV条件下,对252Cf（sf）重裂变碎片（138~148 u）得到的时间分辨为（224:1±6:1）ps;在动能为102 MeV条件下,对252Cf（sf）轻裂变碎片（101~111 u）,得到的时间分辨为（154:5±5:8）ps。In order to separate the mass number of fragments in the fission reactions, it is essential to develop a good time-of-flight (TOF) method. The purpose of this article is to set up a TOF detector system including a microchannel plate (MCP) and a Au-Si surface-barrier detector (SBD). The TOF system shows a detection efficiency of 39% for α-particles released from 241Am and 98% for fragments in the spontaneous fission of 252Cf. The experimental results show that the time resolutions of (224:1±6:1) ps for the heavy fragments (Ek=78 MeV, AH=138~148 u) and (154:5±5:8) ps for the light fragments (Ek=102 MeV, AL=101~111 u) can be obtained.     

高激发核相继裂变的限制

高温核衰变是当前中能重离子核物理中研究最热烈的课题.理论上对高温核的衰变进行了各种预言,相继裂变就是其中之一.本文从有关核裂变的时间尺度、裂前中子发射、裂变截面等随激发能的变化和多重碎裂的实验结果以及复杂碎片发射时间的实验结果分析了对高温核相继裂变的限制,提出了从复杂粒子蒸发向多重碎裂过渡的可能性. Sequential fission is one of the several kinds of theoratical production for hot nucleus de-cay.By analysing relevant experimental results such as fission time scale,prescission neutron emission,fission cross sections and their variation with excitation energy,the results of multifragmentation andthe time scale of complex fragment emission,a limit to the sequential fission of the hot nucleus is sug-gested in this paper.A transition from intermediate mass fragment evaporation to..     

Theoretical analysis on the efficiency of optical-optical double-color double-resonance multiphoton ionization

Analytic formula of the efficiency of optical-optical double-color double-resonance multi-photon ionization （OODR-MPI） is derived from the dynamic rate equation about the interaction of photon and material. Based on this formula, the influence of characteristic of the pump and probe laser on the ionization efficiency of （1＋2＋1） OODR-MPI process is simulated theoretically. It is shown that the pump laser will affect the ionization efficiency by the number control of the molecules excited to the first resonance state. The ionization efficiency is decided by the probe laser directly. Both of the excited molecules and ionization efficiency increase with the intensity and pulse duration of the laser until saturation. It is also found that the longer the delay time of the probe laser to the pump one is, the lower the ionization efficiency would be. The delay time ought to be smaller than the lifetime of the excited molecule in the practical use of the OODR-MPI technique.     

形变相关的壳修正对N=126处断前中子发射的同位素效应的影响

利用动力学加统计模型就形变相关的壳修正（DDSC）对中子126壳层附近209,213,217Fr断前中子发射的影响进行了研究。模拟结果表明,DDSC抬升了复合核的裂变位垒,且213Fr的升高约为209,217Fr的2倍,但却没有改变鞍点位置。尽管位垒升高延缓了系统的裂变,但其动力学过程受热力学驱动力（TDF）和核阻尼间竞争的主导,因此准确提取壳修正的作用还需考虑核耗散的形变关系。在裂变第一阶段,当核耗散取一体耗散（OBD）参数时,壳修正没有改变断前中子发射的同位素效应,然而当核耗散取标准参数设置（SPS）时,由于213Fr的TDF存在着异常增强,故该规律未能展现。在裂变第二阶段,位垒升高引起的断前中子发射的增强受到了TDF与核阻尼间竞争的反制,故断前中子发射的同位素效应仍未能显现。综合两阶段情况,DDSC对N=126处断前中子发射的同位素效应的影响受第一阶段规律的支配。The effect of deformation-dependent shell correction (DDSC) on the emission of prescission neutron (EPN) is studied within a dynamical and statistical model for three isotopes of 209,213,217Fr near the neutron 126 closure-shell. The results show that the fission barriers are enhanced with DDSC, and the increment of 213Fr is almost 2 times those of 209,217Fr, but those saddle points are not changed. Although the enhancement of fission barrier delays nuclear fission, the fission dynamics process is controlled by the competition between thermodynamic driving force (TDF) and nuclear damping, so the deformation-dependence of nuclear dissipation must be considered in order to extract the role of shell correction. The shell correction doesn't alter isotope effect of EPN with OBD nuclear dissipation in the first phase of nuclear fission, but the rule does not been exhibited because that there is abnormal enhancement of TDF using SPS nuclear dissipation. The increment of EPN caused by the rise of fission barrier is countered by the competition between TDF and nuclear damping in the second phase of nuclear fission, hence the effect of EPN cannot exhibit. The effect of DDSC on EPN near the neutron 126 closure-shell is dominated by the rules in the first phase of nuclear fission.     

加速器驱动次临界系统中堆外中子注量率监测方法（英文）

在加速器驱动的次临界（ADS）系统中,次临界反应堆的功率控制是通过控制束流强度来实现。监测堆外中子注量率,不仅提供了反应堆功率指示,也为反应堆保护系统在启动和运行阶段提供了重要的监测信息,因此,堆外中子注量率的监测在ADS系统的控制与保护中起着非常重要的作用。采用3套裂变室和3套非补偿电离室来监测ADS堆外中子注量率。由于裂变室有脉冲、电流和均方电压3种操作模式,1套裂变室可以监测源量程、中间量程和功率量程等宽范围的反应堆功率。所以,使用的监测方法有3个优点,即:增加了监测通道的冗余度,提高了保护系统的可靠性,以及能提供更多的轴向功率分布信息。由于这些中子探测器对中子能谱很敏感,提出了一种有效的校准方法,即先用一个标准的中子源校准这些中子探测器,然后再将中子注量率除以一个修正因素。基于Geant4仿真结果显示,所提取的裂变室和非补偿电离室的修正因素分别为5和42。In an accelerator driven sub-critical (ADS) system, power control in sub-critical reactor is achieved through the control of the beam current. Excore neutron flux monitoring in an ADS system, not only provides indication of reactor power, but also provides important inputs to reactor protection system during startup and power operation, and thus plays a very important role in the control and protection of ADS system. This paper presents the excore neutron flux monitoring method which uses three fission chambers (FCs) and three uncompensated ion chambers (UICs). With three operation modes, pulse mode, current mode, and mean square voltage mode, an FC can monitor reactor power over a wide range from the source range to the intermediate and power ranges. The proposed monitoring method increases the redundancy of independent monitoring channels, improves the reliability of the protection system, and provides more information on axial power distribution. Since these neutron detectors are sensitive to the neutron energy spectrum, we propose an effective calibration method to provide the exact value of neutron flux, i.e., these neutron detectors are calibrated with a standardized neutron source, and then, a correction factor is added in the calibration by comparing the neutron energy spectrum of the neutron source with that in ADS system. Based on Geant4 simulation, the correction factors of 5 and 42 are extracted for FCs and UICs, respectively.     

Measurement of Electron-Drift Velocity in Ar＋CH4 Mixtures Using Double-Grid Method

Based on analyzing the induced signals from the double-grids of an ionization chamber, the electron-drift time between the two grids is determined and the electron-drift velocity is derived. A waveform digitizer is employed to record pulses from the two grids of the ionization chamber. The electron-drift velocity is measured as a function of the reduced electric field E/p for eight different ratios of Ar＋CH4 mixtures. By analyzing the experimental data of this study, self-consistency of experimental data is achieved, and formulae for calculating electron-drift velocity in any ratio of Ar＋CH4 mixtures are obtained.     

Digital signal processing application to <Superscript>252</Superscript>Cf(sf) reaction products spectroscopy

The emission of prompt fission neutrons in spontaneous fission of ²⁵²Cf was studied by the application of digital data processing for the first time. The study was aimed at comparing the obtained results with those from the pioneering work of Budtz-Jorgensen and Knitter. By using a twin Frisch grid ionization chamber for fission fragment detection and a neutron scintillator (NE213) for the detection of neutrons, a total of about 10⁷ neutron coincidences were registered. The fission-fragment kinetic energies were measured using a fast (80 MHz) waveform digitizer that provided 10-bit amplitude resolution. Standard analog NIM modules were used for neutron time-of-flight and pulse shape measurements. A time-to-digital converter (TDC) with 1-ns resolution and a pair of gated charge-to-digital converters with 12-bit amplitude resolution were also used. The fission fragment signals were analyzed by means of digital signal processing algorithms. Data on prompt fission neutron energies were obtained by using a time-of-flight (TOF) spectrum unfolding procedure applicable to list-mode data.     

Correlation between neutrons and fragments in 252Cf (sf)

The gridded ion chamber developed at CBNM provides a powerful tool for measurements of fission fragment angular, kinetic energy and mass distributions with an angular efficiency close to 4π. In the present experiment it is used together with a neutron time-of-flight detector to measure the correlation between neutron emission, fragment angle, mass and energy in the spontaneous fission of ²⁵²Cf.     

利用252 Cf快裂变室测量BC501A液闪探测器的相对探测效率和响应函数

本文利用²⁵²Cf快裂变室和多参数数据采集系统,逐事例的同时记录了自发裂变中子和瞬发伽马的飞行时间(TOF),脉冲形状甄别(PSD)和反冲能量(RE,裂变中子是通过测量反冲质子;瞬发伽马是通过测量康普顿反冲电子)三维信息.详细介绍了通过离线数据分析完全扣除三维信息中的伽马事例贡献,以获得Φ50.8 mm×50.8 mm的BC501A液闪探测器的相对探测效率和响应函数的方法.在不通过探测器响应函数进行数据转换的条件下,利用中子的能量直接确定了中子的有效测量阈值.得到的中子 关键词： 252Cf快裂变室')" href="#">²⁵²Cf快裂变室 BC501A液闪探测器 相对探测效率 响应函数     

Twin position sensitive ionization chamber,utilizing backgammon and time projection method

The anomalous dependence of average prompt fission neutron (PFN) multiplicity on the fission fragment total kinetic energy of ²⁵²Cf(sf) was investigated using digital signal processing (DSP). A twin Frisch-grid ionization chamber (TGIC) was used for fission fragment (FF) spectroscopy and PFN was registered with help of fast neutron detector (FND) on liquid scintillator base. The DSP apparatus was build up around the 8-channel fast synchronously sampling waveform digitizers (WFD). It was found that the main limitation of the experimental method, developed in ref. [1] for investigation of the PFN properties in neutron induced fission reaction ²³⁵U(n,f), ²³⁹Pu(n,f) etc is related to the FF energy loses of in the target backing. A modification of the method was suggested to overcome such a limitation.     

Behaviour of Prompt Gamma-Ray Emission in ColdFission of 252Cf

The behaviour of prompt γ-ray emission in the cold fission of ²⁵²Cf was investigated experimentally using a four-parameter correlation technique. A twin gridded ionization chamber was employed to detect the fission signals and to determine the fragment emission angles, and a φ10cm×10cm NaI(T1) detector was used to record the γ-ray energies. The result shows that the angular distribution coefficient of γ-rays emitted in cold fission is twice as large as that in the normal fission.The fact that in the cold fission the number of γ-rays emitted from the light fragments is approximately three times as large as that from the heavy ones can not be explained satisfactorily so far.     

Measurement of 248Cm/252Cf Cf Spontaneous Prompt Fission Neutron Spectrum

In order to treat the waste material of nuclear power and develop new type of clean nuclear power,it is necessary to measure the neutron adta of long half life nuclei existed in the waste material.The prompt spontaneous neutron spectrum is one of the most important unclear data for new type nuclear power facilities as well as for understanding the mechanism of fission neutron emission.The measurements of ²⁴⁸Cm/²⁵²Cf spontaneous prompt fission neutron spectrum in the neutron energy range form 200keV to 12MeV wer performed by using TOF method.A micro-ionization chamber aws used as fission fragment detector and stibene crystal as neutron detector.The flying paths of neutrons for the measurements were 30cm,50cm and 100cm respectively.The spontaneous prompt fission neutron spectrum of ²⁴⁸Cm was fitted by the Maxwellian distribution and the temperature was determined as (1.401±0.006)MeV in the corresponding neutron energy range.     

一种252Cf裂变中子源的中子、γ射线飞行时间谱测量新方法

 针对²⁵²Cf快中子、γ射线的飞行时间谱测量要求,提出并建立一种基于高速数据采集卡的新型测量系统。采用1 GHz高速A/D转换单元和现场可编程门阵列高速处理单元,进行脉冲时间序列的在线检测,时间精度为1 ns。使用相关函数法,通过PC机的数据处理、互相关函数计算和数值统计等实现中子、γ射线飞行时间谱的测量。实验结果表明,该系统可以获得²⁵²Cf自发裂变中子源的中子、γ射线飞行时间谱,与经典的飞行时间谱测量方法相比较,其图谱表达及数值结果有着很高的吻合度。     

Generation of angular momentum of fission fragments in a cluster model

Based on the dinuclear system concept, the role of bending vibrations in creation of the angular momentum of primary fission fragments is investigated. For ²⁵²Cf spontaneous fission, the angular momenta of the fragments are calculated as a function of the neutron multiplicity and compared with available experimental data. Different cluster compositions of the ²⁵²Cf fission modes at the scission point are considered.