铜-钼源漏电极对非晶氧化铟镓锌薄膜晶体管性能的改善

在铜(Cu)和非晶铟镓锌氧化物(a-IGZO)之间插入30 nm厚的钼(Mo)接触层, 制备了具有Cu-Mo源漏电极的a-IGZO薄膜晶体管(TFT). Mo接触层不仅能够抑制Cu与a-IGZO有源层之间的扩散, 而且提高了Cu电极与玻璃基底以及栅极绝缘层的结合强度. 制备的Cu-Mo结构TFT与纯Cu 结构TFT相比, 具有较高的迁移率(～9.26 cm²·V^-1·s^-1)、更短的电流传输长度(～0.2 μm)、更低的接触电阻(～1072 Ω)和有效接触电阻率(～1×10^-4Ω·cm²), 能够满足TFT 阵列高导互联的要求.     

Grain-size effect in BaTiO3 ceramics: study by far infrared spectroscopy

The article offers comparative study of two nanocrystalline (50 and 100?nm averaged grain size) and two coarse-grain (1.2 and 10?µm averaged grain size) ceramics by means of Fourier transform infrared spectroscopy in a broad temperature range (10–570?K). Far infrared reflectivity spectra were fitted with the factorized model of the dielectric function and the evaluated dielectric function was compared with the results of low-frequency dielectric measurements. It appears that the stiffening and weakening of the overdamped soft mode is the only reason for the reduced dielectric permittivity of nanocrystalline ceramics in the paraelectric phase, but a strong grain-size dependence of the dielectric constant in the ferroelectric phase is not connected with the changes in lattice dynamics. All single-crystal symmetry changes were detected in all of the samples, but no phase-transition discontinuities was seen in nanocrystalline ceramics. A coexistence of more than one phase is suggested. Strong dependence of the Curie-Weiss temperature on the grain size, earlier revealed by others, is confirmed.     

Surface metallization of alumina ceramics by pulsed high energy density plasma process

Surface metallization of alumina ceramics was carried out by pulsed high energy density plasma (PHEDP). A layer of copper film was deposited on the surface of alumina ceramics. Scanning auger electron microscopy (SAM) analysis revealed that copper diffused deep into the alumina substrate. Bonding of alumina and copper film was good. The reaction between copper and alumina was studied by X-ray diffraction (XRD) analysis. A copper aluminum oxide unstable at high temperature and very difficult to be synthesized, cubic phase CuAl₂O₄, was detected. A kinetics complexity in reaction of PHEDP and ceramics was discussed. An adiabatic model was used to describe heating and quenching of the PHEDP processing and analyze the interaction between PHEDP and alumina ceramics. The experimental results suggest that PHEDP method is a useful technology for various metal–ceramics bonding.     

Characterization of nanostructured ceramics prepared by both high energy ball milling and fast firing sintering processes

High-energy ball milling technique was successfully applied to calcinated lead zirconate titanate (PZT 60/40) powders. After 20?h of ball milling, large PZT particles were completely broken down, reducing its initial size in three orders of magnitude. Experimental results show a huge sinterability enhancement of the PZT powders by using this technique, achieving its maximum sintering rate at ～800°C. Relatively low densities (～91%) were achieved in stoichiometric samples, while in 3% lead excess samples sintered at 950°C for 30, 45, 60, 90 and 120?min using a fast firing process and a post-annealing treatment at 800°C for 4 h, densities of ～97% of the theoretical were achieved. PZT nanostructured ceramics prepared under optimized processing conditions (60?h of powder milling, 950°C of sintering temperature, 60?min of sintering time and a post-annealing process at 800°C during 4?h) show high dielectric constant (ε′) values (900) and low dielectric loss (tan?δ) at room temperature and a ferroelectric-paraelectric transition temperature at 375°C.     

Experimental and theoretical evaluation of wettability on micro/nano hierarchically engineered surfaces based on robust micro-post-arrayed- and highly ordered nano-rippled-structures

This paper reports a simple approach for demonstrating a micro/nano hierarchical surface, ensuring both geometrical regularity and mechanical stability, for improving the hydrophobicity. The proposed dual-scale hierarchical surfaces were realized simply by combining the highly self-ordered ripple-like nano patterns with the robust micro-post arrays, based on the cost-effective nonlithographic chemical oxidation process and well-established microfabrication technologies. The wettability of the proposed nano-scale mono- and micro/nano dual-roughened surfaces was evaluated by measuring the apparent contact angles (ACAs), and analyzed theoretically with analytic models based on the Wenzel, Cassie, and combined wetting theories. Through experimental and theoretical observations, it was found that the proposed micro/nano hierarchical structures can improve the wetting property and the superhydrophobic robustness of high- and low-density micro-post arrayed surfaces, respectively.     

Nano‐glass frit for inkjet printed front side metallization of silicon solar cells prepared by sol–gel process

Sol–gel derived nano‐sized glass frits were incorporated into the Ag conductive ink for silicon solar cell metallization. This mixture was specifically formulated for inkjet printing on textured Si wafers with 80 nm thick SiN_x anti reflection coating layers. The correlation between the contact resistance and interface microstructures were studied using scanning electron microscopy and transmission electron microscopy. In addition, the specific contact resistance between the front contact and emitter was measured at various firing conditions using the transfer length model. On an emitter with the sheet resistance of 60 Ω/sq, a specific contact resistance below 5 mΩ cm² could be achieved at a peak firing temperature around 800 °C. We found that the incorporated nano‐glass frit act as a very effective fire through agent, and an abundant amount of Ag crystallites was observed along the interface glass layer. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Thermal characterization of dielectric thin films using an improved genetic algorithm

This paper presents theoretical and experimental investigations of the thermal conductivity and the contact resistance of dielectric materials deposited as thin films. Silicon dioxide and poly(p-phenylene) films deposited on alumina substrates are studied in order to determine simultaneously the thermal conductivity of the film and the resistance of the contact between the film and the substrate. Measurements are obtained by using a photothermal technique, and an improved genetic algorithm (GA), especially suitable for thermal characterizations of thin film structures in the sub-micron range. A theoretical study for evaluating the optimal conditions for the photothermal measurements is presented. This is done by studying the sensitivity of the unknown parameters to the thin film thickness and to the properties of the materials. As the photothermal analysis is basically performed in unsteady state conditions, this study highlights the relation between the intrinsic and effective conductivity of the materials.     

Dosimetric phosphor based on oxygen-deficient alumina ceramics

Oxygen-deficient alumina ceramics with blue luminescence was synthesized in reducing medium (vacuum, presence of carbon) from nanopowder at varying temperatures and annealing time. The structure of the samples, particle size distribution, changes in mass of the samples at different synthesis temperatures were studied. In the obtained ceramics the spectra of photoluminescence are registered in the band centered at 420 nm, which is associated with the F-centers created by oxygen vacancies. The luminescent intensity grows with increasing temperature and annealing time. The thermoluminescence curves feature two peaks whose intensities depend on the temperature of the ceramics synthesis. Dose response of the thermoluminescence peaks of alumina ceramics synthesized at 1700 °C was measured under beta-irradiation.     

Radiation-stimulated effects on the surface of alumina ceramics under high-energy electron and ion irradiation

The effect of high-energy electron and ion beams on the elemental composition and electrical properties of the surface of UF-46, VK 94-1, and VK 100-1 alumina ceramics has been studied by Auger electron spectroscopy and secondaryion mass spectrometry. Electron irradiation of UF-46 and VK 94-1 ceramics causes enrichment of the surface layer with a thickness of ～10 nm with silicon oxides and decreases conductivity. The electron-stimulated destruction of surface oxides on ion-irradiated ceramics is significantly enhanced, depending on the type and energy of implanted ions.     

Dielectric,ferroelectric and piezoelectric properties of (1−x)[K0.5Na0.5NbO3]−x[LiSbO3] ceramics

Lead-free (1?x)[K_0.5Na_0.5NbO₃]?x[LiSbO₃] (x=0, 0.04, 0.05 and 0.06)/(KNN-LS) ceramics were prepared by conventional solid-state reaction route (CSSR). For dense morphology pure KNN ceramic was sintered at 1120 °C and LS modified KNN ceramics were sintered at 1080 °C for 4 h, respectively. The structural study at room temperature (RT) revealed the transformation of pure orthorhombic to tetragonal structure with the increase in LS content in KNN-LS ceramics. Temperature dependent dielectric study confirmed the increase of diffuse phase transition nature with the increase in LS content in KNN-LS ceramics. The presence of orthorhombic to tetragonal (T_O?T) polymorphic phase transition temperature (PPT) ～43 °C confirmed the presence of two ferroelectric (orthorhombic and tetragonal) phases in 0.95KNN-0.05LS ceramics at RT. 0.95KNN-0.05LS ceramics showed better ferroelectric and piezoelectric properties i.e., remnant polarization (P_r)～18.7 μC/cm², coercive field (E_c)～11.8 kV/cm, piezoelectric coefficient (d₃₃)～215 pC/N, coupling coefficient (k_p)～0.415 and remnant strain ～0.07% were obtained.     

Performance of ceramic anvils for high pressure neutron scattering

Three kinds of ceramics, zirconia-toughened alumina (ZTA), alumina-toughened zirconia (ATZ) and yttria-stabilized zirconia (YSZ), were tested as anvil materials, mainly for the purpose of neutron scattering study under high pressure. ZTA with non-toroidal anvil profile, having the same sample volume as conventionally used double toroidal anvils, sustained pressures up to 11.9?GPa. This is comparable to anvils made of tungsten carbide (TC) with Ni binder with the same dimensions. ATZ would also be an alternative material to TC with pressure performance comparable to ZTA, whereas YSZ is much weaker than the other two ceramics. The attenuation coefficient for YSZ is significantly smaller than that of TC and similar to ZTA and ATZ, the latter being estimated by attenuation calculations. Neutron diffraction on a sample of lead in YSZ anvils as well as quasi-elastic neutron scattering on liquid water in ZTA also demonstrate the outstanding neutron transparency of these ceramics. The gain factor in count rate is up to one order of magnitude.     

Spin‐dependent‐magnetoresistance control by regulation of heat treatment temperature for magnetite nano‐particle sinter

The control of spin‐dependent‐magnetoresistance by regulation of the heat treatment (HT) temperature for magnetite (Fe₃O₃) nano‐particle sinter (MNPS) has been studied. The average nano‐particle size in the MNPS is 30nm and the HT was carried out from 400°C to 800°C. The HT of the MNPS varies the coupling form between adjacent magnetite nano‐particles and the crystallinity of that. The measurements on electrical resistance (ER), magnetoresistance (MR) and magnetization were performed between 4K and 300K. The behavior of the ER and MR considerably changes at the HT temperature of ～600°C. Below ～600°C the ER indicates the variable‐range‐hopping conduction behavior and the MR shows the large intensity in a wide temperature region. Above ～600°C the ER shows the indication of the Verwey transition near 110K like a bulk single crystal and the MR designates the smaller intensity. We consider that below ～600°C the ER and MR are dominated by the grain‐boundary conduction and above ～600°C those are determined by the inter‐grain conduction. The magnetic field application to the grain‐boundary region is inferred to cause the large enhancement of the MR.     

99氧化铝陶瓷在不同应变率下的破碎特性

开展了99氧化铝陶瓷在不同应变率下的轴向压缩实验,通过对相应应变率下的试件碎片进行软回收,并结合筛余法对碎片进行几何表征,获得了不同应变率下的碎片尺寸分布曲线和试件破坏的能量吸收过程,建立了颗粒陶瓷的外力功与相对破碎率之间的关系。采用数字图像相关(Digital image correlation,DIC)技术获取了不同应变率下沿加载方向的应变场,并结合能量吸收过程和碎片级配表现分析了破坏模式。实验结果表明:99氧化铝陶瓷的破坏强度与应变率呈正相关,在中应变率下,能量吸收率与应变率呈负相关,由于能量吸收机制的改变,样品初始为劈裂破坏;当应变率达到401 s^?1时,破坏模式变为劈裂-粉碎混合破坏;随着应变率继续增大,试件变为粉碎破坏,颗粒平均粒径减小,碎片尺寸趋同,应力集中的影响逐渐减弱。分析了能量、破坏过程、碎片分布之间的关系,最终获得了碎片分布规律以及破碎特性。     

脉冲高能量密度等离子体沉积(Ti,Al)N薄膜组织及其性能研究

利用脉冲高能量密度等离子体技术在室温条件下在45＃钢基材表面沉积了高硬度耐腐蚀(Ti, Al)N薄膜. 利用扫描电子显微镜、X射线衍射、X射线光电子能谱、俄歇电子能谱分析了薄膜的显微组织.利用纳米压痕仪测试了薄膜的纳米硬度.测试了薄膜在05mol/L H2SO4水溶液中的耐蚀性. 测试结果表明：薄膜主要组成相为(Ti, Al)N，同时含有少量的AlN,薄膜的纳米硬度高达26 GPa,薄膜具有良好的耐蚀性，与1Cr18Ni9Ti奥氏体不锈钢相比，耐蚀性提高了一个数量级. 关键词： 脉冲高能量密度等离子体 薄膜 纳米硬度 耐蚀性     

Synthesis of nanoparticles and preparation and characterization of nanopolymer matrix composites

In this study, nano α-alumina particles were synthesized by a sol–gel method using aqueous solutions of aluminum isopropoxide and 0.5?M aluminum nitrate. 1/3-benzene disoulfonic acid disodium salt (SDBS) and fluoride were used as surfactant stabilizing agent and additive, respectively. Results indicated that the finest size for nonagglomerated nanoalumina particles (15–20?nm) was achieved at 950?°C. The next part was about preparing PP nanocomposite containing nano α-Al₂O₃ particles. Mechanical tests, such as tensile, flexural, and impact tests showed that mechanical properties of the composite were enhanced by addition of nano α-Al₂O₃ particles and dispersant to the polymer. However, higher concentration of nano α-Al₂O₃ loading resulted in reduction of those mechanical properties, which could be due to agglomeration of nano α-Al₂O₃ particles. Transmission and scanning electron microscopic observations of the nanocomposites also showed that fracture surface became more roughened by increasing the content of filler loading from 1 to 4% wt.     

The Kondo effect in reduced graphene oxide films

The influence of spin in reduced graphene oxide (RGO) is demonstrated through a temperature dependent metal–insulator transition in resistance (at ～30 K) as well as high field magneto‐resistance (MR) measurements. RGO samples, prepared using an unconventional organic acid reduction method, showed a quadratic temperature dependence of resistance at low temperatures, which changed to a logarithmic dependence at higher temperatures. Analysis of these features in RGO, combined with negative MR which scales with a Kondo characteristic temperature, establishes the interaction between conduction electrons propagating through intact graphene nano‐islands and localized magnetic moments found in disordered regions. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Preparation of nano/micro-scale column-like topography on PDMS surfaces via vapor deposition: Dependence on volatility solvents

In this work, a column-like nano/micro-scale topography surface has been prepared via trichloro(octyl)silane (TCOS) vapor deposition on the air plasma oxidized polydimethylsiloxane (PDMSOx) surface. TCOS was mixed into n-heptyl alcohol and dimethyl-silicone oil to form a series of mixture. TCOS could anchor to the PDMSOx surface to form column-like nano/micro-scale topography while n-heptyl alcohol and TCOS volatilized to the PDMSOx surface in the subsequent vapor phase process. These surfaces were characterized by X-ray photoelectron spectroscopy (XPS), Fourier transform infrared-attenuated total reflection, contact angle measuring system and atomic force microscopy. It was shown that TCOS had been successfully assembled on the polydimethylsiloxane surface. N-heptyl alcohol mixed into alkylsiloxane could regulate the scale and roughness of column-like nano/micro-scale topography.     

Mid-infrared virtually imaged phased array spectrometer for rapid and broadband trace gas detection

We present and characterize a two-dimensional (2D) imaging spectrometer based on a virtually imaged phased array (VIPA) disperser for rapid, high-resolution molecular detection using mid-infrared (MIR) frequency combs at 3.1 and 3.8?μm. We demonstrate detection of CH₄ at 3.1?μm with >3750 resolution elements spanning >80 nm with ～600 MHz resolution in a <10 μs acquisition time. In addition to broadband detection, we also demonstrate rapid, time-resolved single-image detection by capturing dynamic concentration changes of CH₄ at a rate of ～375 frames per second. Changes in absorption above the noise floor of 5×10^-4 are readily detected on the millisecond time scale, leading to important future applications such as real-time monitoring of trace gas concentrations and detection of reactive intermediates.     

高质量规则多孔氧化铝模板的制备

在合适的条件下利用阳极氧化高纯铝片，可以获得多孔结构的氧化铝，其孔径大小和排列方式都很均匀.由于孔的深度不受限制，因此可以制备出孔深很大的多孔氧化铝.这种多孔结构可以用作制备纳米材料的模板.利用0.3mol/L的草酸溶液在40V的直流电压下，采用二步氧化法获得了高质量的氧化铝多孔模板，其典型孔径值为40—70nm，孔间距约110nm，深度可达毫米量级.分析了溶液温度对结果的影响，比较了单步法和两步法获得的样品的多孔结构，认为低温下的二步氧化法可以获得很好的多孔氧化铝模板. 关键词： 纳米材料 多孔氧化铝 二步氧化法     

The effect of cerium oxide argon-annealed coatings on the high temperature oxidation of a FeCrAl alloy

Ceria coatings were applied in order to improve the adherence of alumina scales developed on a model Fe–20Cr–5Al alloy during oxidation at high temperature. These coatings were performed by argon annealing of a ceria sol–gel coating at temperatures ranging between 600 and 1000 °C. The influence of these coatings on the alloy oxidation behaviour was studied at 1100 °C. In situ X-ray diffraction (XRD) was performed to characterize the coating crystallographic nature after annealing and during the oxidation process. The alumina scale morphologies were studied by means of scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS). The present work shows that the alumina scale morphology observed on cerium sol–gel coated alloy was very convoluted. On the cerium sol–gel coated alloy, argon annealing results in an increase of the oxidation rate in air, at 1100 °C. The 600 °C argon annealing temperature results in a good alumina scale adherence under thermal cycling conditions at 1100 °C.