管梁耦合宽带换能器

对一种管梁耦合宽带换能器进行了研究,通过在圆环换能器中加入弯曲梁组成管梁耦合结构,增加有效工作模态,利用多模谐振耦合优化设计,可使换能器的工作带宽向低频大幅扩展.理论计算与实测结果均表明,管梁耦合换能器具备频带宽、功率大、尺寸小、深水性能好等特点,兼具圆环换能器与弯张换能器的优势,工作性能优良,设计灵活多变.      

钹型换能器的优化设计*

本文研究的钹型换能器,是由一个压电陶瓷圆环和一个金属浅球壳组成。为了得到这种钹型换能器的解析解和它在不同介质中的机电性能。首先,根据前人得出的压电陶瓷圆环和金属浅球壳的理论模型,用等效电路法从理论上计算出了该换能器的共振频率并与仿真结果做了对比,发现二者近似吻合,验证了理论计算的可靠性,为这种钹型换能器的优化设计提供了理论指导。然后利用COMSOL Multiphysics分别模拟了压电陶瓷为圆盘和圆环的钹型换能器的共振频率,仿真结果表明：同等条件下,当圆环的外径和圆盘的半径相等时,压电陶瓷为圆环的钹型换能器共振频率更低,使其具有频率低、体积小的特点更加明显。利用数值方法,分析了钹型换能器的几何尺寸对其共振频率、反共振频率及有效机电耦合系数的影响。最后模拟了钹型换能器在水中的机电特性及声压分布。     

基于2-2型压电复合材料的新型宽频带径向振动超声换能器

本文提出了一种基于2-2型压电复合材料的新型宽频带径向振动超声换能器,它主要由内金属圆环和外压电陶瓷复合材料圆环组成.首先利用Newnham串并联理论和均匀场理论推导了2-2型压电复合材料的等效参数;其次利用解析法得到了金属圆环和径向极化压电复合陶瓷圆环径向振动的机电等效电路;最后得到了换能器的六端机电等效电路,从而得到了换能器的频率方程.接着分析了换能器共振频率和反共振频率以及有效机电耦合系数与几何尺寸、两相体积占比的关系,采用仿真软件对新型换能器的径向振动进行了数值模拟.结果表明,利用解析法得到的共振频率和反共振频率与数值模拟结果吻合较好.此外,对换能器在水下的辐射声场进行了仿真研究,结果表明新型复合材料径向换能器相比传统纯陶瓷径向换能器,发射电压响应幅值更大,工作带宽提高接近一倍,声匹配更佳.     

复合圆环弯曲振动四极子模态分析

针对压电圆环弯曲振动机电转换性能较差的问题,提出了一种复合圆环弯曲振动换能器,它由一个径向极化的压电陶瓷内圆环和一个金属外圆环复合而成。基于能量原理推导得到了复合圆环弯曲振动的谐振频率和有效机电耦合系数,探讨了弯曲振动四极子模态特性与其结构尺寸间的关系。当压电圆环尺寸不变时,随外侧金属圆环壁厚增加,复合圆环弯曲振动四极子模态谐振频率上升,有效机电耦合系数迅速上升到极大值后缓慢下降。最后,设计制作了圆环换能器并对其谐振频率和有效机电耦合系数进行了实验测试,测试结果与解析结果和数值模拟结果吻合得较好。      

自由端盖Ⅲ型宽带弯张换能器的设计

提出了一种利用多模耦合实现低频、宽带、大功率特性的新结构Ⅲ型弯张换能器。通过在压电陶瓷堆内部嵌入与凹型弯张壳体相连的弹性辅助弯曲梁结构,并用弯曲圆盘作为顶部自由端盖,增加有效工作模态。利用有限元方法对换能器进行了设计优化,分析结果显示换能器在低频段存在4个主要工作模态。根据优化结果,加工制作了换能器样机,水池实验的测试结果表明:在1.5～5.5 kHz范围内,换能器样机的发送电压响应均大于135 dB;1.5～4 kHz内的最大发送电压响应大于142 dB,响应起伏小于6 dB。研究结果表明自由端盖Ⅲ型弯张换能器不仅能够在小尺寸设计下实现大功率工作,还能获得低频宽带发射性能。      

阶梯圆环压电超声换能器径向振动性能的理论研究*

提出了一种阶梯圆环径向振动压电超声换能器,根据力电类比原理建立了阶梯圆环及阶梯圆环换能器的径向振动等效电路,推导了阶梯圆环的径向共振频率方程和位移放大系数,在此基础上进一步推导了换能器的径向共振和反共振频率方程。通过理论推导和有限元仿真模拟分析了阶梯圆环压电超声换能器的径向振动性能。结果表明,增大阶梯圆环中内外环的径向厚度之比K1或减小轴向厚度之比K2,阶梯圆环的一阶径向共振频率减小,二阶径向共振频率增大;在二阶径向共振模式下,K1、K2值在一定范围内阶梯圆环可实现由内向外的径向位移振幅放大;随着压电陶瓷圆环的内半径增大,阶梯圆环压电超声换能器的一阶、二阶径向共振和反共振频率减小,二阶径向共振下的有效机电转换系数趋于零;增大阶梯圆环内环的外半径,换能器的一阶径向共振和反共振频率减小,二阶径向共振和反共振频率先增大后减小,理论推导与仿真模拟结果符合良好。本文研究结果为阶梯圆环压电超声换能器的工程应用提供理论参考。     

Study on the radial composite piezoelectric ceramic transducer in radial vibration

A new type of radial composite piezoelectric transducer in radial vibration is developed and analyzed. The radial composite transducer consists of a piezoelectric ceramic thin ring polarized in the thickness direction and a metal thin circular ring. They are connected together and excited to vibrate in the radial direction. The radial vibrations of a piezoelectric ceramic thin ring and a metal thin circular ring are analyzed, respectively. Their radial electro-mechanical equivalent circuits are obtained. Based on the electro-mechanical equivalent circuits and using the boundary conditions between the piezoelectric ceramic thin ring and the metal thin circular ring in the radial direction, the electro-mechanical equivalent circuit of the radial composite piezoelectric transducer is derived out and the resonance frequency equation is obtained. The relationship between the resonance frequency and the geometrical dimensions of the transducer is analyzed. Some radial composite piezoelectric transducers are designed and manufactured. The resonance frequencies and the anti-resonance frequencies, the electro-mechanical equivalent circuit parameters are measured. The effective electro-mechanical coupling coefficient and the mechanical quality factor are calculated. It is illustrated that the measured radial resonance frequencies are in good agreement with the theoretical results from the resonance frequency equation.     

Terahertz wave switch based on photonic crystal ring resonators

In this paper, we have presented a compact and integrated terahertz wave switch design based on photonic crystal ring resonators. The photonic crystal structure with square lattice is investigated and applied for design of ring resonators. The switching mechanism of this novel switch is based on the variation of the resonant frequency of the ring resonator inserted between two parallel waveguides. The refractive index of the holes of the structure filled with polyaniline electrorheological fluids are varied by applied external electric field, the result of which is the variation of the ring resonant frequency. The proposed device is analyzed by using finite difference time domain method. Numerical simulation results show that this switch has high extinction ratio, small size, low voltage and advantages of selectivity of coupling THz wave to different output ports.     

锥形剖面径向复合超声换能器的机电等效电路

研究了一种锥形剖面径向复合超声换能器。该换能器由一个等截面内金属圆环、一个轴向极化的压电陶瓷圆环和一个锥形剖面外金属圆环沿径向复合而成,且换能器的径向尺寸远大于高度。锥形剖面外金属圆环满足关系式h=h₀r,h₀为厚度变化常数。基于平面应力径向振动理论,推导了换能器的机电等效电路,得到了共振频率方程和反共振频率方程,进而研究了换能器的振动特性。并将理论计算的第1阶、第2阶径向共振频率和反共振频率与数值仿真结果相比较,二者结果一致。研究表明:锥形剖面换能器第1阶、第2阶径向共振频率、反共振频率、有效机电耦合系数不仅与换能器各部分的材料、径向几何尺寸有关,还与h₀有关。h₀越大,第1阶径向共振频率、反共振频率越大,有效机电耦合系数先增大后减小。与等截面相比,锥形剖面换能器沿径向向外辐射声波,辐射面积更大,辐射声功率更高,指向性更好。      

夹心式径向复合压电超声换能器

对夹心式径向复合压电换能器径向振动特性进行了研究。该换能器由弹性内芯、预应力金属管及柱面压电陶瓷晶堆径向复合而成.利用机电类比法,得到了换能器的径向振动等效电路及频率方程。探讨了换能器第1、2阶径向共振频率及有效机电耦合系数与其几何尺寸的关系。研究表明,换能器第1阶径向共振频率随其内芯内径及预应力管壁厚度增大而降低;第2阶共振频率随内芯内径增大存在极小值,但随预应力管壁厚度增大单调下降。此外,采用第2阶径向共振模式能获得较高的有效机电耦合系数,并且压电陶瓷处于位移节线时,换能器有效机电耦合系数达极大值。对换能器共振频率的测试与有限元仿真表明。理论与实验及仿真结果符合较好。      

双壳嵌套鱼唇式弯张换能器

研究了一种双壳嵌套鱼唇式弯张换能器,针对特殊结构的空气背衬弯张换能器提出了表征换能器静压形变的系列参数,利用有限元方法研究了这些参数与结构参数的对应关系,并进行了换能器的静态分析。在静态分析基础上,研究了结构参数对换能器声辐射特性的影响,经对比分析得到换能器的优化方案,研制了实验样机,经外场试验验证了双壳嵌套鱼唇式弯张换能器具有小尺寸、频率低、高效率、大功率的工作特性:谐振频率800 Hz、最大声源级199.5 dB、电声效率23.6%、工作深度200 m。      

Design of a self-calibrating simulated acoustic emission source

The use of conical piezoelectric transducers as point acoustic sources has been investigated. It has been shown that transducers based on a design originally developed at the National Institute for Standards and Technology in the USA can be used as point transmitters over the frequency range of interest in acoustic emission measurements (100 kHz to around 1 MHz). They should, therefore, be suitable for use in experiments to calibrate structures so that acoustic emission source strengths can be determined. It has also been shown that measurements of the response of the transmitting transducer backing can be used to assess the coupling efficiency, and hence to remove concerns about inconsistent coupling affecting the calibration measurements. The results indicate that the variation of the backing response with coupling is due to a shift in the resonance frequencies of the transducer with the mechanical load impedance. If other transducers can be shown to behave in a similar fashion this effect could be used to measure coupling in standard acoustic emission and ultrasonic transducers.     

圆环状复合材料高频宽带水声换能器

研制了一种圆环状高频宽带水声换能器。利用压电复合材料Q值低从而频带宽的特点,采用双环轴向堆叠产生双模态耦合的结构方式拓宽换能器的带宽。通过理论分析与仿真计算,确定敏感元件几何尺寸。用切割-浇注-被覆电极等工艺制备出压电复合材料圆环;再将制备出的外径相同,壁厚不等的压电复合材料圆环轴向叠堆制成叠堆敏感元件,最后灌注防水透声层制成换能器。对制得的换能器进行水下性能测试,测得该换能器谐振频率为410 kHz,最大发射电压响应为150 dB,-3 dB带宽达60 kHz,水平指向性开角(-5 dB)为360°,-3 dB垂直指向性开角约20°。结果表明将复合材料圆环轴向堆叠可显著拓展换能器的带宽,且实现声波的水平全向发射。      

PMN-PT single crystal thick films on silicon substrate for high-frequency micromachined ultrasonic transducers

In this work, a novel high-frequency ultrasonic transducer structure is realized by using PMNPT-on-silicon technology and silicon micromachining. To prepare the single crystalline PMNPT-on-silicon wafers, a hybrid processing method involving wafer bonding, mechanical lapping and wet chemical thinning is successfully developed. In the transducer structure, the active element is fixed within the stainless steel needle housing. The measured center frequency and −6 dB bandwidth of the transducer are 35 MHz and 34%, respectively. Owing to the superior electromechanical coupling coefficient (k _t ) and high piezoelectric constant (d ₃₃) of PMNPT film, the transducer shows a good energy conversion performance with a very low insertion loss down to 8.3 dB at the center frequency.     

A conical piezoelectric transducer with integral sensor as a self-calibrating acoustic emission energy source

The experimental results of a conical piezoelectric transducer with integral backing sensor as a self-calibrating simulated acoustic emission (SAE) energy source are presented. It has been shown that there is a negative linear relationship between the energy of SAE signal detected by the backing sensor and the relative strength (signal energy) of SAE source in the structure detected by a reference sensor under different transducer-to-structure coupling efficiencies, with AC drives of the same wave packet, frequency and peak amplitude to excite the conical transducer as a SAE source at all the investigated frequencies over the frequency range of interest in AE measurements (nominally from 50 kHz to around 1 MHz). This should enable the relative strength of the SAE source in a structure to be determined using the SAE measurement from the backing sensor for the selected electrical inputs to the conical transducer, and hence to remove the concerns about inconsistent transducer-to-structure coupling affecting the relative strength of the SAE source for calibration.     

微波低通高阻复合材料构件的设计与性能验证

随着海洋环境武器装备隐身发展的需要, 开展具有微波低通高阻特性的复合材料构件设计与研究显得重要而迫切. 文章首先设计了一种中空六边形周期性结构, 以此为基础设计了一个由面层、中空六边形环周期层1、中间层、中空六边形环周期层2、面层组成的新型复合双层频率选择表面(FSS)结构件. 其上层FSS的结构参数为中空六边形环边长3.0 mm, 线宽度0.5 mm, 缝隙宽度0.4 mm; 下层FSS的结构参数为中空六边形环的边长3.2 mm, 线宽度0.5 mm, 缝隙宽度1.0 mm. 模拟结果表明: 该复合材料构件具备优良的低频透过性与高频屏蔽性快速转换的特性, 能够获得优异的低通高阻性能, 同时在45°范围内具备优良的角度不敏感性. 最后制备和实验验证得到了0–2 GHz低频段具有95.6%高透过性、同时在7.05–18 GHz高频段具有10 dB 以上屏蔽性能的复合材料构件, 对具有隐身特性的新型滤波电磁功能构件的研制具有重要价值.     

Generation and detection of nano ultrasound waves with a multiple strained layer structure

In this paper a multiple strained layer structure with multiple quantum wells as a piezoelectric transducer is proposed for generating and detecting nano ultrasound waves with nanometer wavelength and tera hertz frequency. By inducing femtosecond optical pulses at this strained structure, internal piezoelectric field is changed. As a result longitudinal acoustic phonon oscillations can be treated as nano acoustic waves. It could be noticed in simulated cases that detection of nano ultrasound waves can be used in non destructive testing and high accuracy measurements with this structure. It is also shown that the MQW structure design how influences in generated nano acoustic waves.     

声子晶体结构在功率超声换能器中的应用*

该文提出了一种二维声子晶体结构模型,并将该模型应用于横向尺寸较大的功率超声换能器的前盖板中,避免了形成耦合振动对换能器的影响,从而优化了该类换能器的工作性能。首先设计了一种具有近周期性结构的圆柱形孔的前盖板,然后研究了声子晶体结构前盖板散射体的半径大小和高度对换能器共振频率以及前盖板带隙的影响。结果表明,随着散射体半径和高度的增大,换能器的共振频率会随之发生改变,带隙范围也在发生变化,可以通过调节使换能器的共振频率处于声子晶体的带隙范围内,可以有效抑制换能器的横向振动。     

Mode analysis of trilaminar bender bar transducers using an approximation method

Based on the vibration theory of a thin plate, an analytical treatment of the trilaminar bender bar with piezoelectric elements and inert substrate of various lengths is presented for mode analysis. Resonance frequency and effective electromechanical coupling coefficient are calculated by this method. The impacts of the geometries of the bender bar on the performance of its fundamental and third-order flexural mode are investigated in detail under rigid boundary conditions. It is shown that resonance frequency is extremely sensitive to the thickness of inert substrate. Moreover, the effective electromechanical coupling coefficient has peaks as the length of piezoelectric elements varies. The peaks are achieved when the length of piezoelectric elements equals the length between two nodes having zero strains in the x-direction. The trilaminar bender bar will be effectively excited when the strains on the piezoelectric element are in the same phase, which is important to disclose the vibration mechanisms of this kind of transducer. Also, analytical results are compared with the ones of numerical simulation. The results suggest that effective electromechanical coupling coefficient shares similar patterns with electrical conductance, which can be used to characterize transducer performance to a certain extent. It also demonstrates that the analytical treatment provides an efficient alternative way for optimizing the bender bar transducer design.     

空心聚合物微珠/环氧树脂复合材料匹配层空耦式压电换能器

研制了一种厚度模空耦式压电换能器,使用综合考虑材料衰减系数和声阻抗的空耦式压电换能器电力声等效电路理论模型以指导匹配层结构设计和材料选择,选用新型的空心聚合物微珠/环氧树脂复合材料作为声匹配材料,优化设计电阻抗匹配及结构参数。该换能器中心频率为510 kHz,-6 dB频域相对带宽为25.4%,插入损耗为-27 dB。结果表明,使用新型低衰减系数的闭孔复合材料单匹配层设计的该换能器不仅保证了高灵敏度,同时简化了换能器结构,为空耦式压电换能器研制提供了新思路。