级联双折射光纤环镜滤波特性的分析

从理论上研究了级联双折射光纤环镜滤波器的滤波特性，给出加隔离器与不加隔离器两种不同结构的串联双环镜滤波器透射光强的表达式，并对于两个环镜取不同的周期比时的滤波特性进行了数值模拟和分析.得出串联环镜滤波效果与级联顺序无关，光隔离器对滤波效果不会产生影响，只是增加了插入损耗.通过级联和改变两个环镜的双折射光纤长度比，可以获得不同的滤波效果.最后给出了多个环镜直接级联后透射光强的通项表达式，通过对通项式的理论分析可以设计不同的滤波器.     

自均衡线性相位高温超导滤波器的设计

针对第三代移动通信CDMA 2000标准用超导滤波器的技术要求,设计了一种自均衡线性相位高温超导滤波器,给出了14阶三个交叉耦合的CQ结构滤波器理论计算结果、等效电路、耦合矩阵,设计的滤波器中心频率为830MHz,65%带宽内的群时延波动优于±10ns,滤波器模拟仿真结果与理论计算很好得吻合。     

TD-SCDMA通信系统用大功率高温超导滤波器

针对TD-SCDMA通信系统的要求,设计了一种可以承载大功率信号的双模高温超导滤波器,给出了双模大功率滤波器的设计理论、设计过程以及功率承载能力的推算。滤波器用LAO基片的高温超导薄膜制作,中心频率为2017.5MHz,通带宽度为15MHz,功率承载能力达到10W以上,滤波器的测试结果与设计结果吻合较好。     

中国联通GSM900通信系统用高温超导滤波器的研制

设计了用于中国联通GSM900移动通信系统接收频段的高温超导滤波器,给出了滤波器的理论设计和模拟仿真结果,滤波器的微带电路制作于2英寸MgO基片双面DyBa2Cu3O7高温超导薄膜上,中心频率为912MHz,相对带宽为0.66%,滤波器的工作温度为75K,各项技术指标均满足了GSM900系统的要求。     

阵列波导光栅梳状带通滤波器的传输效率

在光波导模场分布高斯近似条件下,根据星形光波导耦合器的耦合特性,推导出了基于累加运算和卷积运算近似表达的阵列波导光栅梳状带通滤波器光谱响应效率的函数表达式。给出了阵列波导光栅梳状带通滤波器光谱响应效率曲线的半最大值全宽度和阵列波导光栅梳状带通滤波器的通道中心波长的光谱响应度与器件参数的关系。在输入信号光谱分布高斯近似条件下,给出了阵列波导光栅梳状带通滤波器信号通道传输效率的计算表达式和输入信号光谱宽度对阵列波导光栅梳状带通滤波器信号通道输出特性的影响。给出了物理意义明确的函数表达式,它们可为快速分析阵列波导光栅梳状带通滤波器的特性提供理论基础。     

SHF频段超宽带高温超导滤波器的研制

针对超宽带通信系统的发展趋势,采用1/4波长短截线结构设计了一个工作于超高频(SHF)频段的超宽带高温超导滤波器,滤波器的中心频率为4.2 GHz,相对带宽为50%,讨论了1/4波长短截线结构滤波器的设计原理,给出了所设计超宽带滤波器的理论曲线、模拟仿真结果。实际制作的超宽带高温超导滤波器的测量曲线与模拟仿真曲线基本吻合,得到了满意的结果。     

对Cohn直耦滤波器理论的推广

本文把Cohn的直耦滤波器理论推广到四分之一波长耦合滤波器,从而使这两种类型的微波滤波器在理论上统一起来。给出了低通到带通的频响变换式,这个变换式考虑了滤波器电纳随频率改变。实验结果表明,应用导出的设计公式进行设计,预示的带宽和阻带衰减更接近实际。最后,对频响特性不对称性的消除方法进行了一些讨论。     

对Cohn直耦滤波器理论的推广

本文把Cohn 的直藕滤波器理论推广到四分之一波长藕合滤波器, 从而使这两种类型的微波滤波器在理论上统一起来. 给出了低通到带通的频响变换式, 这个变换式考虑了滤波器电纳随频率改变. 实验结果表明, 应用导出的设计公式进行设计, 预示的带宽和阻带衰减更接近实际. 最后, 对频响特性不对称性的消除方法进行了一些讨论。 关键词：     

带有条形间隔矩形腔结构的波导滤波器特性分析

设计了一种带有条形间隔的矩形腔结构波导滤波器,并且利用时域有限差分法(FDTD)对其滤波特性进行了分析。结果表明该滤波器可以看成是两个T形腔的背向耦合,其透射性质与单T形腔类似,改变腔的长度和宽度可以改变透射谱的中心波长,以实现不同波长的滤波功能。     

带有条形间隔矩形腔结构的波导滤波器特性分析

设计了一种带有条形间隔的矩形腔结构波导滤波器,并且利用时域有限差分法（FDTD）对其滤波特性进行了分析。结果表明该滤波器可以看成是两个T形腔的背向耦合,其透射性质与单T形腔类似,改变腔的长度和宽度可以改变透射谱的中心波长,以实现不同波长的滤波功能。     

Dynamical behaviour of birefringent Fabry–Perot cavities

In this paper we present a theoretical and experimental study of the dynamical behaviour of birefringent cavities. Our experimental data show that usual hypothesis which provides that a Fabry–Perot cavity is a first-order low-pass filter cannot explain the behaviour of a birefringent cavity. We explain this phenomenon and give the theoretical expression of the equivalent cavity filter which corresponds to a second-order low-pass filter.     

Woodpile结构三维光子晶体中的四端口通道下载滤波器

基于三维光子晶体空间完全带隙的特性,本文在实验上构建了一种由非共面的两个波导和一个立体微腔组成的四端口通道下载滤波器。讨论了球体、正方体、长方体微腔滤波器的选频特性,以及连续旋转长方体微腔时,其输出频率的变化。研究结果表明,无论是对称型还是非对称型微腔,都可以较好地实现选频。提高微腔的不对称性,共振输出频率随之发生移动,说明改变微腔的对称性,可以有效调节滤波器的选频特性。连续旋转非对称型长方体微腔,输出频率会随之发生明显的移动,如果引入有效调节机制,可以产生连续调节输出频率的效果。该研究结果给多端口选择性输出空间滤波器的设计提供了新的思路,为光学器件集成化的设计提供了重要的理论参考。     

一种基于矩形腔的MIM波导滤波器的滤波特性研究（英文）

理论提出并研究了一种基于矩形腔的窄带金属-介质-金属波导滤波器.建立滤波器内电场的传递矩阵模型,研究了矩形微腔与直通波导间耦合特性对器件滤波特性的影响.同时,研究了耦合长度、矩形微腔腔长、传输损耗等因素对滤波带宽的影响.研究结果表明,对于不同的矩形微腔腔长,存在一个可使器件滤波带宽达到最窄的耦合系数.此外,当微腔腔长越长且传输损耗越小时,滤波带宽也将越窄.该研究为表面等离子体波导的研究与设计提供了一定的参考.     

Efficient noise suppression of an amplified diode-laser by optical filtering and resonant optical feedback

We present the noise suppression of an amplified diode laser by using an optical filter and resonant optical feedback. The intensity noise of the amplified diode laser has been significantly decreased by using the optical filter cavity. It was further suppressed and reached the shot noise limit at 15 MHz by introducing resonant optical feedback from the transmission of the filter cavity. The filter cavity transmits 53% of injection power, and the output power of the filter cavity is more than 200 mW. The observed frequency fluctuations were less than 100 kHz in one minute. This level of noise suppression and output power may allow diode lasers to be utilized in many quantum-optics experiments. PACS 42.55-f; 42.55-Px; 42.50.-p     

Single-longitudinal-mode fiber ring laser using fiber grating-based Fabry-Perot filters and variable saturable absorbers

A single-longitudinal-mode (SLM) fiber ring laser is demonstrated by incorporating a fiber Bragg grating (FBG)-based Fabry-Perot (F-P) filter and a variable saturable absorber in a fiber ring cavity. An ultra-narrow bandpass filter is established by the combined mode filtering of the FBG-based F-P filter and the variable saturable absorber. No accurate control for cavity length is required, and stable single longitudinal-mode operation without mode hopping is conveniently achieved.     

交指型腔体滤波器设计

为抑制EAST装置现场的电磁信号对低杂波系统运行的干扰,设计了一个交指型腔体滤波器,其中心频率为2.45GHz,带宽为0.245GHz。介绍了交指型腔体滤波器的设计思路和方法,利用高频电磁仿真软件HFSS仿真提高了设计效率和精度。     

82-channel multi-wavelength comb generation in a SOA fiber ring laser

We demonstrate a multi-wavelength semiconductor optical amplifier (SOA) fiber ring laser with a dual-pass Mach-Zehnder interferometer (MZI) filter. Two SOAs with different gain spectra provide sufficient gain and a wider gain spectrum to facilitate multi-wavelength lasing. The dual-pass MZI, configured by adding an optical isolator to the two outputs of the conventional MZI, serves as comb filter for multi-wavelength operation, and its extinction ratio can be enhanced to twofold as that of the conventional MZI in the same parameters. To investigate the influences of a dual-pass MZI filter and a conventional MZI filter on multi-wavelength operation, two different cavity configurations are presented and compared, including a single-SOA ring cavity and a double-SOA ring cavity. Stable simultaneous operation at 82 wavelengths, with a wavelength spacing of 40 GHz and a power deviation of 5 dB, and with a minimum optical signal-to-noise ratio (OSNR) of 28 dB, is observed from the double-SOA ring cavity using a dual-pass MZI filter.     

Finite-difference time-domain analysis of deformed square cavity filters with a traveling-wave-like filtering response by mode coupling

An add-drop filter based on a perfect square resonator can realize a maximum of only 25% power dropping because the confined modes are standing-wave modes. By means of mode coupling between two modes with inverse symmetry properties, a traveling-wave-like filtering response is obtained in a two-dimensional single square cavity filter with cut or circular corners by finite-difference time-domain simulation. The optimized deformation parameters for an add-drop filter can be accurately predicted as the overlapping point of the two coupling modes in an isolated deformed square cavity. More than 80% power dropping can be obtained in a deformed square cavity filter with a side length of 3.01 microm. The free spectral region is decided by the mode spacing between modes, with the sum of the mode indices differing by 1.     

滤波位置相关的全正色散掺Yb3+锁模光纤激光器的实验研究

采用非线性偏振旋转锁模,构建了一种全正色散掺Yb³⁺光纤环形激光器.在该激光腔内采用了10 nm带宽的光纤滤波器提供附加的自振幅调制.通过改变滤波器在腔内的位置,实验证明了滤波器位置对高啁啾脉冲的整形过程起到重要的作用.在320 mW的抽运功率下,最终获得平均功率为922 mW,脉冲重复频率为266 MHz,脉冲宽度为62 ps的稳定脉冲输出,单脉冲能量达35 nJ的优化结果.通过数值模拟与实验结果的验证表明,两者相符很好. 关键词： 锁模光纤激光器 全正色散 滤波效应 高啁啾脉冲     

850 nm centered wavelength-swept laser based on a wavelength selection galvo filter

A wavelength-swept laser is constructed using a free space external cavity configuration coupled with a fiberbased ring cavity at the 850 nm region. The external cavity filter employs a galvo-mirror scanner with a diffraction grating for wavelength selection. The filter is connected to a ring cavity through an optical circulator.The ring cavity contains a broadband semiconductor optical amplifier with a high optical output. The performance of this laser is demonstrated with broad bandwidths and narrow linewidths. The 3 dB linewidth and the bandwidth of this source are 0.05 nm(~20 GHz) and 48 nm, respectively. The maximum output power is 26 m W at 160 m A current.