基于MEH-PPV/ZnSe纳米复合器件的电致发光特性的研究

以巯基乙酸作为稳定剂在水相中制备了ZnSe纳米晶,用X射线粉末衍射(XRD)和X射线光电子能谱(XPS)对其进行了表征。用表面活性剂将ZnSe纳米晶从水相中转移到有机相中,使其与聚合物MEH-PPV复合作为发光层,制备了多层电致发光器件Glass/ITO/MEH-PPV∶ZnSe/BCP/Alq₃。对ZnSe纳米晶和MEH-PPV薄膜的光致发光谱及其吸收光谱的比较表明ZnSe纳米晶和MEH-PPV之间存在着能量传递,这是导致纳米复合薄膜的光致发光光谱和电致发光光谱存在差异的原因之一。文章对其在光激发和载流子注入条件下的不同发光机制进行了讨论。通过对器件的光电特性进行研究,发现ZnSe纳米晶发光的比例随着外加电压的增加而增加,而且器件的I-V特性基本上符合二极管的特性。     

Er3+,Yb3+共掺杂NaGd（MoO4）2荧光粉的发光特性

采用高温固相法制备了Er3+,Yb3+共掺杂的NaGd(MoO4)2荧光粉,通过X射线衍射对样品的物相结构进行了分析,采用荧光光谱手段对样品的下转换发光特性和上转换发光特性进行了研究。通过对激发、发射光谱的分析,发现基质到Er3+存在有效的能量传递。通过对样品上转换发光光谱的分析,发现在不同Yb3+掺杂浓度样品中,红光和绿光上转换发光均为双光子过程,并对样品上转换发光强度与LD泵浦电流和掺杂离子浓度的关系进行了讨论。     

Zno纳米晶的室温紫外受激发射特征

ZnO的激子特性对制备氧化锌基的光电子器件至关霞要,因此对ZnO量子点中激子的发光性质及其跃迁过程进行研究显得十分必要.采用溶胶-凝胶法制备了ZnO纳米晶,X射线衍射(XRD)结果表明样品具有六角纤锌矿多晶结构.研究了在不同泵浦功率激发下ZnO纳米晶的紫外发射的时间积分光谱和时间分辨光谱,观察到自南激子发光,激子-激子碰撞和电子-空穴等离子体引起的受激发射,研究了在不同泵浦功率激发下自由激子及激子-激子碰撞随泵浦功率依赖的动力学过程.研究结果对理解激子带边发射有一定帮助,对ZnO材料在短波长半导体光电器件方面有潜在的应用价值.     

Tb~(3+)掺杂含SrF_2纳米晶硅酸盐微晶玻璃的光谱性质

通过高温熔融法和后续热处理制得Tb~(3+)掺杂含SrF_2纳米晶的透明硅酸盐微晶玻璃。利用X射线衍射(XRD)、透射电子显微镜(TEM)、紫外可见透过光谱、荧光光谱、荧光寿命和X射线激发发光光谱(XEL)探讨了基础玻璃和微晶玻璃的结构和光谱特性。XRD结果表明,玻璃中析出晶体为SrF_2纳米晶,衍射峰随着热处理温度的升高和时间的延长而逐渐明显,晶粒也随热处理温度的升高和时间的延长越来越大。在376 nm紫外光和X射线激发下,与基础玻璃相比,微晶玻璃发光显著增强,且发光强度随热处理温度的升高和时间的延长而逐渐增强。     

Lu_2O_3:Yb~(3+),Tm~(3+)纳米晶的结构和上转换发光性能研究

采用共沉淀法制备了Yb3+和Tm3+共掺杂的Lu2O3纳米晶,用X射线衍射(XRD)、场发射扫描电子显示镜(SEM)和上转换光谱对样品进行了表征。研究了Tm3+浓度和煅烧温度对粉末的结构和上转换发光性能的影响。结果表明,制备出的纳米晶具有纯的Lu2O3相,结晶性较好。在980 nm半导体激光器激发下,样品发射出蓝光、红光和近红外光,并且当Tm3+掺杂摩尔分数超过0.2%时,出现了浓度猝灭效应。随着煅烧温度的增加,纳米晶的尺寸增大,上转换发光强度增强。发射强度与激发功率的关系表明,蓝光490 nm和红光653 nm的发光是三光子过程,近红外811 nm的发光是双光子过程。     

两步法制备空间取向高度一致的ZnO纳米棒阵列

采用两步法,即先用磁控溅射在Si(100)表面生长一层ZnO籽晶层、再利用液相法制备空间取向高度一致的ZnO纳米棒阵列.用扫描电子显微镜、X射线衍射、高分辨透射电子显微镜和选区电子衍射对样品形貌和结构特征进行了表征.结果表明,ZnO纳米棒具有垂直于衬底沿c轴择优生长和空间取向高度一致的特性和比较大的长径比,X射线衍射的(XRD)(0002)峰半高宽只有0.06°,选区电子衍射也显示了优异的单晶特性.光致发光谱表明ZnO纳米棒具有非常强的紫外本征发光和非常弱的杂质或缺陷发光特性. 关键词： ZnO纳米棒阵列 ZnO籽晶层 两步法 液相生长     

PEI/CeF3 : Tb3+纳米晶体的简易合成及荧光特性

用水热法制备了PEI/CeF₃ : Tb³⁺纳米晶体,运用透射电子显微镜,X射线衍射,傅立叶变换近红外光谱,对样品进行了表征。结果表明:所得纳米晶体平均粒径为10 nm,呈比较规则的立方体形;纳米晶体表面包覆有PEI,因而具有较好的水溶性和潜在的生物应用价值。我们给出了该纳米晶体的荧光激发谱与发射谱,详细说明了各发光峰对应能级的跃迁及其发光机理,分析了不同掺杂浓度对其荧光强度的影响。结果表明:所制备的纳米晶体在紫外光激发下,显示出明亮的绿色荧光。当Tb³⁺离子掺杂摩尔分数20%左右时,样品的荧光强度达到最大值。     

二氧化钛阵列的制备及其光学性能

以水热法制备了由纳米棒组成的二氧化钛阵列。通过控制反应时间,对组成阵列的二氧化钛纳米棒的尺寸进行调节。利用扫描电镜和X射线衍射光谱分析了样品的形貌和晶体结构,发现将反应时间由4 h延长至8 h,二氧化钛纳米棒的直径由100 nm增大到200 nm。利用紫外-可见吸收光谱测量了样品的光吸收特性,发现了尺寸效应引起的吸收边和带隙变化,反应时间由4 h延长至8 h,样品带隙由3.09 eV变化至2.97 eV。利用荧光光谱研究样品的光致发光性能,发现了样品的近带边发光(382 nm左右)、自陷激子发光(420 nm左右)、束缚激子发光(456 nm左右)和缺陷能级发光(492 nm左右)。     

水热法制备ZnS:Cu,Tm超细X射线发光粉

研究了水热法合成的ZnS: Cu,Tm超细X射线发光粉及其光致发光(PL)和X射线激发发光(X-ray excited luminescence,XEL)光谱特性.200 ℃水热处理12 h直接合成样品的纳米晶粒径约15 nm,尺寸分布窄,分散性好,具有纯立方相的类球形结构.氩气保护下900 ℃退火1 h后的样品存在一定的团聚,但团聚后尺寸为200—600 nm,为超细X射线发光粉,此时样品为纯六方相的类球形为主的结构.所有样品的PL和XEL光谱均为宽带谱.水热法直接合成样品的XEL强度最强时,样品的Cu/Zn,Tm/Cu比值分别为3×10^-4和2.在此比值条件下,900 ℃退火1 h样品的XEL发光最强,此时其两个峰值分别位于453,525 nm.发光强度增强的同时粒径很小,对提高成像系统分辨率非常有意义.通过比较PL光谱与XEL光谱特性,讨论了PL和XEL光谱的发光机理和其不同的激发机理. 关键词： ZnS:Cu Tm 水热法 X射线激发发光     

La6WO12：Eu3+纳米荧光粉的合成及荧光纳米纤维膜的制备

采用Pechini法合成了La6WO12:Eu3+纳米荧光粉.分别用X射线粉末衍射(XRD)、扫描电子显微镜(SEM)、热重分析(TG-DTG)、反射光谱,荧光光谱和发光衰减曲线对样品进行了表征.该荧光粉可以被395nm的近紫外光有效激发,进而得到峰值波长位于615 nm(电偶极跃迁5D0→7F2)左右的红光发射.将该...     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.     

Eu3+掺杂MMoO4(M=Ca,Sr)荧光粉的表征及发光性质

本文采用简易的Pechini方法制备了Eu3+掺杂MMoO4(M=Ca,Sr)红色荧光粉.产物的结构、形貌和性质分别通过X射线衍射(XRD)、扫描电子显微镜(SEM)、光致发光发射谱(PL)和激发谱(PLE)进行表征分析.XRD表明反应得到了纯相目标掺杂产物,SEM照片显示两种体系掺杂产物形貌均匀性不同,Eu3+掺杂C...     

Growth mechanism and photoluminescence of the SnO2 nanotwists on thin film and the SnO2 short nanowires on nanorods

SnO2 nanotwists on thin film and SnO2 short nanowires on nanorods have been grown on single silicon substrates by using Au-Ag alloying catalyst assisted carbothermal evaporation of SnO2 and active carbon powders.The morphology and the structure of the prepared nanostructures are determined on the basis of field-emission scanning electron microscopy(FESEM),transmission electron microscopy(TEM),selected area electronic diffraction(SAED),high-resolution transmission electron microscopy(HRTEM),x-ray diffraction(XRD),Raman and photoluminescence(PL) spectra analysis.The new peaks at 356,450,and 489 nm in the measured PL spectra of two kinds of SnO2 nanostructures are observed,implying that more luminescence centres exist in these SnO2 nanostructures due to nanocrystals and defects.The growth mechanism of these nanostructures belongs to the vapour-liquid-solid(VLS) mechanism.     

CeO2:Eu3+粉末的溶胶-凝胶法制备及发光性能研究

采用溶胶-凝胶法制备了不同浓度Eu3 掺杂的CeO2发光粉,样品粉末在紫外光激发下发出明亮的橙红色光.利用X射线衍射(XRD)、热重-差热分析(TG-DTA)和光致发光光谱(PL)对样品的结晶过程和发光性质进行了表征.XRD分析表明在0.2at.%～10at.%的Eu3 掺杂范围内,用溶胶-凝胶法合成的样品在500℃就结晶成纯相的CeO2:Eu3 多晶粉末.由于Ce4 和Eu3 离子半径十分接近,因而Eu3 在CeO2中具有较高的固溶度.PL激发谱中出现在300～390 nm的宽带激发峰起源于基质CeO2的吸收,电子吸收能量后,发生O2--Ce4 的电荷迁移,再将能量传递给Eu3 .PL发射谱显示Eu3 含量为6at.%的样品发光强度最强,随后出现浓度猝灭.导致发光出现浓度猝灭的机制是电偶极-电四极相互作用.样品烧结温度的升高,促使晶粒长大和结晶完整性提高,从而显著提高了CeO2:Eu3 粉末的发光强度.     

InN分凝的InGaN薄膜的光致发光与吸收谱

我们用低压MOCVD在蓝宝石衬底生长了InGaN/GaN外延层.用X射线衍射(XRD),光致发光谱(PL),光吸收谱等测量手段,研究了InGaN的辐射发光机制.In组分利用Vegard定理和XRD测量得到.我们发现随着In组分的增加,在光吸收谱上发现吸收边的红移和较宽的Urbach带尾;PL谱中低能端的发射渐渐成为主导,并且在PL激发谱中InGaN峰也变宽.我们认为压电效应改变了InGaN的能带结构,从而影响了光学吸收特性.而在InN量子点中的辐射复合则是InGaN层发光的起源.     

Influence of annealing temperature on structural, optical and magnetic properties of Zn0.95Cu0.02Cr0.03O powders

Zn_0.95Cu_0.02Cr_0.03O powders have been synthesized by the sol-gel method and sintered in argon atmosphere under different temperatures. The structural, optical and magnetic properties of the powders were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and vibrating sample magnetometer (VSM). The XRD results demonstrated that Cr and Cu ions are incorporated into ZnO successfully when annealing temperatures were 600 and 700 °C. But when the samples were annealed at 500 °C, the crystallinity of the samples was not very good. However, when the annealing temperature was increased to 800 °C, the secondary phase of Cu and ZnCr₂O₄ appeared in the samples. The PL spectra revealed that the position of the ultraviolet (UV) emission peak of the samples showed a blue shift and the green emission peak enhanced significantly with the annealing temperature increasing from 600 to 700 °C. Magnetic measurements indicated that the room temperature ferromagnetism of Zn_0.95Cu_0.02Cr_0.03O was intrinsic in nature. In addition, the saturation magnetization (Ms) increased from 0.0078 to 0.0088 emu/g with the annealing temperature increased from 600 to 700 °C.     

Titanium dioxide synthesized using titanium chloride: size effect study using Raman spectroscopy and photoluminescence

Titanium dioxide nanocrystals were prepared by the wet chemical method and characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), Raman scattering (RS) and photoluminescence techniques. The XRD pattern shows the formation of single phase anatase structure of average sizes ∼7 nm (sample A) and ∼15 nm (sample B) for two samples. Additionally, TEM and RS were used to confirm the anatase crystal structure for both samples. The PL spectra show that the intensity of the sample A is more than that of sample B, which has been attributed to defect(s) and particle size variation. A modified phonon confinement model incorporating particle size distribution function and averaged dispersion curves for two most dispersive phonon branch (Γ‐X direction) have been used to interpret the size effect in Raman spectra. The obtained Raman peak shift and full width at half‐maximum agree well with the experimental data. Our observations suggest that the phonon confinement effects are responsible for a significant shift and broadening for the Raman peaks. Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization of atomic-layer MoS_2 synthesized using a hot filament chemical vapor deposition method

Atomic-layer MoS_2 ultrathin films are synthesized using a hot filament chemical vapor deposition method. A combination of atomic force microscopy(AFM), x-ray diffraction(XRD), high-resolution transition electron microscopy(HRTEM), photoluminescence(PL), and x-ray photoelectron spectroscopy(XPS) characterization methods is applied to investigate the crystal structures, valence states, and compositions of the ultrathin film areas. The nucleation particles show irregular morphology, while for a larger size somewhere, the films are granular and the grains have a triangle shape. The films grow in a preferred orientation(002). The HRTEM images present the graphene-like structure of stacked layers with low density of stacking fault, and the interlayer distance of plane is measured to be about 0.63 nm. It shows a clear quasihoneycomb-like structure and 6-fold coordination symmetry. Room-temperature PL spectra for the atomic layer MoS_2 under the condition of right and left circular light show that for both cases, the A1 and B1 direct excitonic transitions can be observed. In the meantime, valley polarization resolved PL spectra are obtained. XPS measurements provide high-purity samples aside from some contaminations from the air, and confirm the presence of pure MoS_2. The stoichiometric mole ratio of S/Mo is about 2.0–2.1, suggesting that sulfur is abundant rather than deficient in the atomic layer MoS_2 under our experimental conditions.     

Ti/Si比例对Tb3+掺杂TiO2-SiO2复合粉末的发光影响

用溶胶-凝胶法制备了Tb3+离子掺杂的TiO2-SiO2复合粉末并研究了Ti/Si比例对复合粉末光致发光的影响。采用X射线衍射(XRD)、Raman和光致发光谱(PL)对Tb3+离子掺杂的TiO2-SiO2复合粉末进行了一系列的表征。PL谱的结果表明Tb3+离子5D4-7F5跃迁对应的550nm绿光发射最强。随着Ti/Si比例的减小, Tb3+离子在可见光范围的发光逐渐增强, 这可能是由于Tb3+离子周围环境的非晶化加剧引起的。     

不同溶胶体系对纳米氧化锌发光特性的影响

采用溶胶-凝胶工艺制备ZnO纳米粉体,研究了两种不同溶剂下制备的纳米ZnO的荧光特性。实验结果表明两种氧化锌样品有相同的晶型和能带结构,其紫外发光相似,但其带间的可见发射表现出了巨大差异,其原因在于两溶剂的极性不同导致两体系凝胶、烧结的微过程不同,从而使两种ZnO样品的表面态结构和布局发生变化。