利用法布里-珀罗腔抑制电光相位调制中的剩余幅度调制

激光经电光相位调制后,由于剩余幅度调制的存在造成调制边带幅度不相等。利用法布里-珀罗腔的透射特性和Pound-Drever-Hall技术对通过法布里-珀罗腔的调制光正、负一级边带的幅度产生不同的衰减,使得调制边带的幅度相等,从而实现对电光相位调制中剩余幅度调制的抑制。采用该方法,理论上计算了调制光经法布里-珀罗腔后的光外差光谱信号,获得锁定法布里-珀罗腔后调制边带幅度的不对称度较腔锁定前减小四个数量级。实验研究了调制光经法布里-珀罗腔透射的光外差光谱,结果表明将法布里-珀罗腔锁定于该透射光外差光谱中心零位时,对剩余幅度调制的抑制程度可达45 dB。     

光纤光栅法布里-珀罗腔的腔、栅边缘特性分析

把组成光纤光栅法布里-珀罗腔的两个光纤光栅的初相位纳入了讨论范围,用耦合波方程推导了任意初相位下光纤光栅法布里-珀罗腔的透射和反射率的表达式.其中的相位因子包含了由光传播常数调制的腔长、光纤光栅的相位突变、光纤光栅仞相位和由光纤光栅空间频率涮制的光栅长度等四部分.分析了光纤光栅初相、由光栅空间频率调制的光栅长度两个因子对反射谱的影响,并提出了一种把光纤光栅法布里-珀罗腔等效为理想法布里-珀罗腔的方法.     

正弦相位调制双法布里－珀罗干涉术的实验研究

讨论了光纤传光、正弦相位调制的双法布里－珀罗（Ｆａｂｒｙ－Ｐｅｒｏｔ）干涉术实验结果．通过光强信号的傅里叶分析，证实基频幅值和相位均含谐振腔长度或程函变化信息，从而提出实现基频相位或幅值测量的时间间隔测量法或幅值整流基频幅值测量法．在已研制的实验装置上，测试两种方法的灵敏度阈，结果表明：作者提出的平行双通道结构和光纤传光的测试方法能补偿谐振腔温漂影响，简化信号处理过程，更适合实时测量．     

法布里-珀罗干涉信号的小波变换相位补偿算法

为了高精度提取光纤法布里-珀罗干涉信号的腔长信息,结合小波变换的多尺度细分功能,通过小波脊线精确提取干涉光谱每点的相位信息,并采用谱峰信息进行相位补偿,提高腔长解调精度。仿真结果表明,该算法的解调误差理论上可达±0.060 nm。实验结果表明,该算法的腔长解调分辨率相较于最小二乘相位校正法提高了1倍,分辨率可达0.514 nm,加速度传感器实验解调的分辨率达到0.9 mg,在法布里-珀罗传感器动静态参数高精度测量中具有一定的应用前景。     

利用光纤法布里-珀罗谐振器干涉透射波长同时测量混合溶液中多溶质浓度

为了同时探测混合溶液中多种溶质的浓度,提出一种用光纤法布里-珀罗谐振器作为传感器测量混合溶液中多溶质浓度的测量系统.从理论上分析了光纤法布里-珀罗谐振器干涉透射波长与混合溶液浓度之间的关系,采用光纤法布里-珀罗谐振器干涉透射波长实现了高准确度同时测量混合溶液中多溶质浓度的原理和可行性.构建了由InGaAs发光二极管光源、光纤耦合器、FFPR传感器、光电信号转换和放大器、光谱分析仪等组成的测量系统.对乙醇和甘油的9组标准混合溶液进行测量实验,并用测量结果标定了混合溶液中各溶质浓度与光纤法布里-珀罗谐振器传感器干涉透射波长之间的数学解析关系式.根据数学关系式用Action Script 2.0脚本语言编写程序,计算机实时监控了混合溶液中各溶质浓度的变化过程.     

利用光纤法布里-珀罗谐振器干涉透射波长同时测量混合溶液中多溶质浓度(英文)

为了同时探测混合溶液中多种溶质的浓度,提出一种用光纤法布里-珀罗谐振器作为传感器测量混合溶液中多溶质浓度的测量系统.从理论上分析了光纤法布里-珀罗谐振器干涉透射波长与混合溶液浓度之间的关系,采用光纤法布里-珀罗谐振器干涉透射波长实现了高准确度同时测量混合溶液中多溶质浓度的原理和可行性.构建了由InGaAs发光二极管光源、光纤耦合器、FFPR传感器、光电信号转换和放大器、光谱分析仪等组成的测量系统.对乙醇和甘油的9组标准混合溶液进行测量实验,并用测量结果标定了混合溶液中各溶质浓度与光纤法布里-珀罗谐振器传感器干涉透射波长之间的数学解析关系式.根据数学关系式用Action Script 2.0脚本语言编写程序,计算机实时监控了混合溶液中各溶质浓度的变化过程.     

用于光纤布拉格光栅法布里-珀罗腔的改进的Rouard算法

比较了光纤布拉格光栅法布里一珀罗腔的极限法、平衡法及传输矩阵法3种算法,证明了它们是一致的,指出了光纤布拉格光栅复振幅传输矩阵的相移特性对法布里一珀罗腔透射率的影响.对计算任意折射率调制的光纤布拉格光栅的Rouard算法进行了改进,在分层方法中考虑了折射率分布初始相位的影响,获得了更为准确的反射复振幅相位特性,将该结果应用于计算光纤布拉格光栅法布里一珀罗腔,得到了光纤布拉格光栅法布里一珀罗腔具有多峰结构的透射谱,并经过实验验证了该理论的正确性.     

法布里-珀罗干涉仪测平板玻璃折射率的方法研究

根据光线在法布里-珀罗干涉仪中的传播特点,提出了测量平板玻璃折射率的方法 .首先对法布里-珀罗干涉仪中插入平板玻璃前、后所产生的相邻等倾干涉亮纹直径平方的差值和法布里-珀罗干涉仪内、外介质的折射率之间的关系分别进行了理论分析;然后搭建实验光路,使用移测显微镜对干涉亮纹直径进行观察和测量,在平板玻璃厚度已知的前提下,即可得出平板玻璃的折射率,且实验中观察到的现象和测量结果与理论分析相吻合.     

高速大容量光纤光栅解调仪的研究

采用半导体光放大器和可调谐法布里-珀罗滤波器,以环路结构组成高速扫描激光器,结合光耦合器、光环路器和光电二极管等,形成4通道大容量高速光纤光栅解调仪。系统采用2kHz的类三角波调制信号,驱动法布里-珀罗滤波器在50nm的光谱范围内进行快速扫描。通过引入光纤梳状滤波器和单峰滤波器组成的参考通路,消除法布里-珀罗滤波器的非线性效应和扫描波长漂移问题,使得解调仪具有很好的稳定性和线性度。高速光纤光栅解调仪的稳定性为2pm,分辨率为1pm,线性度为0.99957,测量精度为5pm,解调频率为2kHz。     

基于椭球封闭空气腔的光纤复合法布里-珀罗结构折射率传感特性研究

提出了基于微椭球型空气腔的在线型光纤复合法布里-珀罗干涉结构,并对其折射率传感特性进行了研究.椭球型空气微腔是利用光纤熔接机对实芯光子晶体光纤和单模光纤以特定的熔接参数熔接形成.用高斯光束模型和ABCD法则分析了椭球型空气腔的腔内损耗,建立了电磁场在复合法布里-珀罗干涉结构中传播的物理模型.根据腔长比值的不同,环境折射率对干涉条纹的影响有对比度调制和波长调制,主要研究了一种波长调制型复合法布里-珀罗结构折射率传感器.仿真结果表明该折射率传感器在1—1.6范围内不出现折射率转折点;实验结果表明在1.333—1.466范围内,折射率灵敏度～37.088 nm·RIU-1,分辨率约为2.69×10-5.该光纤复合法布里-珀罗结构干涉条纹对比度高、体积小、成本低,用于折射率测量可靠性高、分辨率高、无折射率拐点、温度串扰小.     

A new method for angular displacement measurement

We describe a new method for angular displacement measurements that is based on a Fabry-Perot interferometer. A measurement accuracy of 10-8 rad is obtained by use of the sinusoidal phase modulating interferometry. Another Fabry-Perot interferometer is used to obtain the key initial angle of incidence.     

基于相位调制器与Fabry-Perot干涉仪的激光多普勒频移测量方法

提出了一种激光多普勒频移测量方法, 此方法利用正弦相位调制使信号光在原频率成分基础上产生正负一阶边带, 再由Fabry-Perot干涉仪对调制光振幅和相位进行调整, 使其产生固定频率的拍频信号, 利用此拍频信号的振幅随频率变化而变化的性质来进行多普勒频移测量. 通过理论分析证明该方法具有很高的测量精度, 加工装调难度不大, 兼顾了普通相干与非相干探测方法的优势. 另外通过实验证明该方法的正确性与可行性, 并通过与普通非相干方式比较发现该方法在测量精度上可以提高 约1个数量级. 关键词： 多普勒频移 相位调制 Fabry-Perot干涉仪 拍频     

Sinusoidal Phase-Modulating Fabry-Perot Interferometer for Angular Displacement Measurement

In this paper, a sinusoidal phase-modulating Fabry-Perot interferometer is proposed to measure angular displacement.The usefulness of the interferometer is demonstrated by simulations and experiments.     

Sinusoidal Phase-Modulating Superluminescent Diode Interferometer with Fabry-Perot Etalone for Step-Profile Measurement

In this paper we use a superluminescent diode (SLD) as the light source of an interferometer and extract a narrow spectrum from a wide spectrum of the SLD with a Fabry-Perot Etalone (FPE). By varying sinusoidally the distance between the two mirrors of FPE, the central wavelength of the narrow spectrum is scanned sinusoidally. The distance between the mirrors is exactly set by a feedback control system, and sinusoidal phase-modulated SLD light that has a large scanning width of about 10 nm can be obtained with high stability and spatial uniformity. The phase of the interference signal has two different components. One is amplitude Z_b of sinusoidal phase modulation, which is proportional to the optical path difference (OPD) and the scanning width. The other is conventional phase α, which provides a fractional value of the OPD in the range of the wavelength. By combining the two values of the OPD obtained from Z_b and α, an exact OPD larger than the wavelength can be measure with ment accuracy in α. Characteristics of the interferometer are made clearly through step-profile measurements.     

Strain Sensor Using Optical Fiber Unsymmetrical F-P Cavity and the Characteristic Analysis

An intrinsic Fabry-Perot cavity consisted of different reflective mirrors is used in fiber-optical sensors for measuring the strain. The character of the unsymmetrical fiber-optical Fabry-Perot cavity and fiber-optic longitudinal stress-strain effect is analysed. The general theory and measurement method of strain are presented. A low fineness Fabry-Perot cavity is used to improve the linearity of optical fiber strain sensors. The result of experiment agrees well with the theory.     

Fabry-Perot interference-based fiber-optic sensor for small displacement measurement

A simple fiber-optic sensor based on Fabry-Perot interference for small displacement measurement is investigated both theoretically and experimentally. A broadband light source is coupled into a Fabry-Perot cavity formed by the surfaces of a sensing fiber end and the measured object. The interference signals from the cavity are reflected back into the same fiber. A small displacement via changes in cavity length can be obtained by measuring the wavenumber spacing of the interference fringes. The experimental data meet with the theoretical values very well. Given the light source bandwidth of 40 nm and the initial distance of 30 μm, the proposed displacement sensing system could achieve high resolution measurement of 16 nm.     

Tristability and self-oscillations in a double resonator system

A system consisting of two coupled Fabry-Perot resonators, one of them nonlinear, with an additional feedback between them is studied experimentally and theoretically. The dependence between the phase shift δφ of the resonator 2 and the laser-induced thermal load Q applied to the resonator 1 is essentially nonlinear. This nonlinearity of the additional feedback in the double resonator system is shown to make possible its self-oscillations and the existence of the tristable 8-shaped hysteresis curves. The frequencies of the observed self-oscillations are in the range from 100 Hz to 100 kHz, their shapes varying from sinusoidal to square and sawtooth.     

Strain Sensor Using Optical Fiber Unsymmetrical F-P Cavity and the Characteristic Analysis

1 IntroductionSuper-accuracy measurements are increasingly needed with rapid development ofscience and technology. In all kinds of measurements, the optical fiber sensors have. many advantages such as inherent immunity to electronical disturbances, high isolationand can be used in explosive and combutive circuxnstances. OPtical fiber sensors can bedivided into two general classes, interferometric devices and intensity-based devices. In' recent years, great effort has been devoted to the devef…     

Transparent Fourier transform spectrometer

We realized a transparent Fourier transform spectrometer and investigated its operating principle. The spectrometer consists of a low-reflectivity Fabry-Perot interferometer and a partially transparent photodetector, which allows for the operation of the spectrometer in transmission. By changing the distance between the low-reflectivity mirrors of the Fabry-Perot interferometer, the light intensity that reaches the partially transparent photodetector is modulated and the spectral information of the incident light is determined by the Fourier transform of the generated photocurrent. This transparent Fourier transform spectrometer allows easy miniaturization and integration into any kind of optical system.