军用运输机机舱有源消声实验系统的设计与实现

为验证有源消声技术在军用运输机机舱低频噪声消除方面的有效性,设计和实现了一套机舱有源消声实验系统。采用“激振器+舱壁板”方式实现了飞机螺旋桨对机舱诱导噪声的声源模拟,设计了基于前馈控制结构的自适应有源噪声控制系统,构建了基于FX-LMS算法的自适应消声控制器,采用监测麦克风组对舱内空间的消声效果进行监测。实验结果验证了自适应有源噪声控制技术在军用飞机舱室消声降噪领域的有效性,并表明初、次级声源间距对自适应有源消声系统的消声效果具有重要的影响。     

局部空间自适应宽带有源消声

本文提出一个局部空间自适应宽带有源消声系统,该系统能实现有源消声所要求的任意带宽噪声在局部空间衰减,能自动补偿背景噪声及消声装置中不可控参数及噪声源变化对消声效果的影响.自适应滤波由TMS 32010数字信号处理器采用NLMS算法多路并行处理完成.实验结果表明:对普通房间中的单次级源布置方式,在主次级源前方1m,±30°扇面区域内,该系统对20—600Hz内的宽带噪声抵消,取得的最大降噪量在25dB(A)以上.     

次级源近场和管壁弹性对充液管路有源消声性能的影响EI北大核心CSCD

建立了含次级源结构的充液直管有源消声系统数值模型,重点分析了声激励下次级源近场和管壁弹性对有源消声性能的影响。结果表明:次级源近场为非均匀声场,误差点位于该区域时部分频点控制效果较差甚至放大,而处于声场均匀区域时可使降噪量提高10 dB以上,增加误差点数量可使绝大多数频点的降噪量提高5 dB以上;管壁弹性使次级源与管壁间的耦合较强,非对称分布的次级源容易激起管壁振动,导致降噪谷值的出现,采用对称分布的次级源可显著提升控制效果;增加次级源数量能够提高系统的有源无源复合控制效果,但使得管内声场变得复杂,多次级源模型的有源消声效果随频率升高而有所降低。     

750 kV变电站电晕噪声的影响与防治

电晕噪声不同于的传统的电气设备噪声,其发声位置高、频带宽、声源分散,是750 kV变电站噪声控制的薄弱环节.该文以西北某750 kV变电站为例,使用紫外成像仪定位了36处主要电晕噪声点,基于噪声实测和全站声场仿真分析,研究了电晕噪声对变电站声环境的影响.针对主要电晕点的实际情况,提出了具体的电晕噪声防治措施.治理措施在...     

参量阵扬声器在管道噪声控制中的研究*

为了解决管道有源噪声控制中声反馈造成的系统复杂度和计算量的增加,文中引入参量阵扬声器作为次级声源,利用其强指向性减小控制系统的声反馈。为了验证该方法可行性,本文分别在直管和L管中,对600 Hz单频噪声和频率范围为500 Hz~1000 Hz的窄带噪声进行了管道有源噪声控制,同时测量了参量阵扬声器的管内声场和降噪范围。结果表明,参量阵扬声器声反馈小,在没有声反馈补偿的条件下对单频噪声的降噪效果基本达到了声反馈补偿条件下普通扬声器的降噪效果,对窄带噪声的降噪效果稍差。此外,通过测量管道声场和降噪量,确定了参量阵扬声器的降噪区域为误差传感器下游整个管道,降噪面积为管道整个截面。这说明参量阵扬声器作为次级声源降低了系统的复杂度和算法的计算量,并取得了较好的降噪效果。     

基于有限元-抛物方程混合模型的气泡幕降噪效果研究

针对以往气泡幕降噪效果研究中气泡幕模型设置过于理想,无法真实反映气泡幕降噪效果空间不均匀性的问题,该文采用有限元-抛物方程混合模型对包含气泡幕的水下打桩噪声场进行了仿真模拟,分析了应用气泡幕时打桩噪声的传播特性,并重点研究了气泡幕的厚度、占空比以及布放位置等不同参数下气泡幕的降噪效果。结果表明,增加气泡幕的厚度可有限提高气泡幕的降噪量,气泡幕的占空比应保持在0.5%～1%,气泡半径较大的气泡幕在较低频率有更好的降噪效果,此外应合理调整气泡幕的布放位置以应对打桩噪声的多途传播特性。该文方法和分析研究结果对打桩施工时气泡幕的参数设置具有指导意义和一定应用参考价值。     

一种基于改进累积方差百分比的红外高光谱数据降噪方法

降低红外高光谱观测数据中的噪声水平是提高温湿廓线反演精度和反演稳定性的重要环节。采用主成分分析法降噪时,最优主成分个数k的选择一般是根据统计和经验的方法确定。统计的方法大都是根据累积方差百分比法,通过人为设定累积贡献率阈值确定最优主成分个数,使得该方法具有较大的主观性和随意性;经验的方法则需要实时的等效噪声光谱(NESR)数据做标准化处理将非均匀噪声转化为高斯分布,而实时的NESR数据在很多情况下不易获取。针对上述问题,提出了一种基于改进累积方差百分比的主成分降噪方法,通过迭代计算选取不同主成分时重构光谱辐射与模拟光谱辐射的偏差来计算累积贡献率阈值,根据阈值确定最优的主成分个数。该方法解决了确定累积贡献率阈值主观随意性的问题,并且不需要实时的NESR数据做标准化处理。根据物理反演结果分析了数据的标准化对降噪的影响,结果表明,标准化对降噪效果的影响很小,由标准化造成的k值计算误差对降噪效果的影响更大。利用该方法对2011年4个季度中具有代表性的数据做降噪处理,反演的温度廓线均方根误差相比于经验公式法在0.32～3 km高度上提高了约0.1 K,与利用等效噪声光谱标准化后的降噪数据的反演结果精度相当。在无法获取等效噪声光谱数据情况下,该方法可以客观合理地对地基红外高光谱数据进行降噪。     

微机在有源消声中的应用

本文讨论将微机技术引入单源有源消声器。微机控制其可变参数,使消声系统能对噪声源进行自动跟踪。其参数在一定范围内随着消声情况的变化而变化,始终保持最佳的消声效果。对线状谱噪声可将其剩余噪声控制在本底噪声或比本底噪声稍高一点的范围内(～3dB)。跟踪速度较快,最佳消声状态的稳定性也较好。     

水下流激孔腔噪声前馈有源控制实验研究

水流流经腔体时引起的自激振荡会形成流激噪声,该文通过仿真和实验研究了水下流激孔腔噪声的主动声场控制。应用有源前馈控制方法,对比了参考信号的选取以及控制器中增加的泄露因子对控制结果的影响,并在水循环管路中对流激孔腔噪声前馈控制效果进行了实验验证。研究结果表明,前馈有源噪声控制方法可有效抑制水下流激孔腔噪声,在误差点和辅助观测点都取得了良好的降噪效果,最大降噪量大于8 dB,并且使用腔内信号作为参考的控制效果优于上游信号作为参考。     

用HQ管抑制管道风扇噪声的数值模拟

针对HQ管抑制风扇噪声这一主动控制噪声的方法开展研究,包括理论分析和数值模拟,在圆管情况下使用HQ管的消声效果预测和HQ管各几何参数对消声效果影响的讨论.结果表明:HQ管在抑制风扇低频噪声方面有十分显著的效果.     

嵌入式质量块对隔声门低频段隔声性能的影响

针对隔声门低频隔声性能差的问题，将嵌入式质量应用于隔声门中以提高隔声门在低频段的隔声性能，通过建立两个相邻混响室的有限元模型计算隔声门的隔声量。基于该模型，并结合隔声门低频隔声性能的评价方法，对在低频段影响隔声门有效隔声量的相关参数进行了参数关联性研究和优化，优化结果表明：对于92 mm厚，容重24 kg/m3的玻璃棉，使用灰铸铁作为质量块，并合理布置各个质量块的大小及其在玻璃棉中的相对位置可以有效提高隔声门在低频段的隔声性能；与普通隔声门相比，在低频段嵌入式质量隔声门的有效隔声量增加了5.0 dB。     

Experimental and numerical study on aeroacoustic sound of axial flow fan in room air conditioner

Fan is one of the main noise sources of the room air-conditioners. Axial flow fans are widely used in the outdoor unit of split type air-conditioners. The interaction between the fan and the heat exchanger should be taken into consideration. However, only a few researches have been carried out on predicting the aeroacoustic noise because of the difficulty in obtaining detailed information of the flow field. This paper is to understand the generation mechanism of sound and to develop a prediction method for the flow field and the acoustic pressure field of the outdoor unit. Acoustic measurement is performed in a semi-anechoic chamber. Effects of each components is analyzed. Based on commercial computational fluid dynamics (CFD) code, Fluent, Fukano’s model is used to predict the overall sound pressure level of broadband noise. The predicted sound pressure levels based on original Fukano’s model are 7.66 dB and 7.42 dB lower than measurement results at 780 rpm and 684 rpm, respectively. And the errors are about 13%. However, when wake width and relative velocity are both calculated by numerical simulations and the distance to blade trailing edge is taken into consideration, the difference of sound pressure level between measurement and prediction is less than 3.4 dB and errors less than 5.5% while the distance is less than 10 mm. Thus, the distance to blade trailing edge should also be an important parameter for Fukano’s model. In comparison with experimental results, it is clearly shown that the Fukano method based on numerical simulation can provide more accuracy than the original Fukano model and numerical results are in a reliable level.     

主变压器噪声特性分析及复合隔声结构设计*

超高压变电站的主变压器的噪声影响已引起广泛关注。以某典型化设计的500kV变电站A的主变压器为例,进行了现场测试,得到其主变压器噪声能量主要集中在中低频范围内,且具备明显的线谱噪声特征。针对该噪声特点,提出了一种内插微穿孔板的双层带孔板型声学超材料的复合隔声结构。使用传递矩阵理论对该复合结构进行了分析,并在阻抗管中进行了实验验证。实验结果表明：该复合隔声结构具备针对性隔声要求,理论与实验传递损失曲线基本吻合。     

瓦状阻尼橡胶块对高铁车轮减振降噪的影响分析

依据声学测试标准,为了评价某型高铁车轮在安装不同形式橡胶块装置后的减振降噪效果,在半消声室内基于B&K振动噪声测试分析系统,对裸轮和橡胶块车轮开展振动声辐射室内测试实验,并基于有限元方法对车轮模态进行了仿真分析。测试结果可知:相比裸轮,WA、WB车轮模态阻尼比显著增加,车轮的减振效果明显,其中WA车轮的减振效果略优于WB车轮。径向激励下,WA车轮声功率级降低了8 dB(A),WB车轮声功率级降低了5.5 dB(A);轴向激励下,WA车轮声功率级降低了8.2 dB(A),WB车轮声功率级降低了6.2 dB(A)。分析可知橡胶块装置能有效抑制车轮的滚动噪声和曲线啸叫,对车轮的减振降噪有积极作用。     

Urban ambient outdoor and indoor noise exposure at home: A population-based study on schoolchildren

To investigate residential exposure to environmental noise among children in an urban area, a noise measurement campaign was performed at the residences of 44 schoolchildren. Outdoor and indoor noise levels were simultaneously recorded during one week inside and outside each child’s bedroom and in the other room where each child spent most of his or her time, called “the main room”. Associations between equivalent noise levels and familial or environmental characteristics were explored.The recorded equivalent continuous sound levels (L_Aeq) were prone to large variability between dwellings regardless of the measurement location and time of day. Factors linked to outdoor noise level differed from those associated with indoor noise level. Indoor noise levels were associated with the number of children present and noise sources present in the dwelling, whereas outdoor L_Aeq depended significantly on the socio-economic status (SES) of the household. An association was found between the type of view from the window and outdoor L_Aeq, but no significant association was observed between view from the window and indoor L_Aeq. These results support a complex link between noise exposure and the characteristics of the dwelling and of the family, and highlight the contribution of the indoor noise sources to the ambient noise level.Considering the observed acoustic levels and their variability, the sensitivity of children to noise, and the length of time they spend at home, research efforts are needed to better quantify noise exposure at home if the actual burden of noise on child health is to be identified.     

Comments on “variational equations for thin elastic shells”

A further study consisting of acoustic and subjective measurements of 552 Chinese firemen at 12 fire stations in Hong Kong has been carried out. Annoyance with aircraft and traffic noise conditions, as expressed by the firemen, was found to correlate well with the acoustic measurements. For aircraft noise the correlation of annoyance with the Number and Noise Index (NNI) was slightly better than with the dB(A) peak value. For traffic noise the similar correlation with the mean sound pressure levels which exceeds 10 % of the sampling period (L₁₀) was slightly better than with the Noise Pollution Level and the Traffic Noise Index. The correlation of the arousal due to the aircraft and traffic noise was similarly found to depend on the NNI and L₁₀ values. However, traffic noise was responsible for more disturbance than aircraft noise. The study demonstrated the desirability of adopting indoor acoustic measurements instead of outdoor measurements for any survey of this kind.     

散热片对变压器声辐射的影响及优化分析*

油浸式配电变压器表面布有大量散热片结构,使得油箱振动声辐射变得复杂。该文研究了散热片结构对油浸式变压器辐射声场的影响,在此基础上提出了散热片结构尺寸的优化措施。建立了考虑流固耦合的变压器振动和声学分析模型,提出了散热片声场效应评判准则,基于模态分析和频响分析探讨了散热片对变压器振动声辐射影响的振动效应、声源效应和声障效应。实验数据和仿真分析结果表明,变压器散热片对变压器振动声辐射的影响不可忽视,尤其是声源效应。采用遗传算法对散热片分布和尺寸参数进行优化分析,计算结果表明,通过优化散热片可以有效降低变压器表面均方振速和辐射声功率,可为变压器噪声控制和优化提供依据。     

Experimental study for control of sound transmission through double glazed window using optimally tuned Helmholtz resonators

This paper presents an experimental investigation of passively control of sound transmission through a double glazed window by using arrangement of Helmholtz resonators (HRs), which are commonly used for narrow band control application. The laboratory experiments were performed placing the window between reverberation chamber and anechoic chamber. The window was subject to diffuse field, approximate normal wave and oblique wave acoustic excitations. Three sets of HRs were designed and installed in cavity of window. The sound control performances at far-field were measured. The control performances from varying the number of HRs, incident acoustic field, excitation sources (band-limited white noise and traffic noise examples) are presented and discussed in detail. It is shown that a considerable reduction of the transmitted sound pressure levels has been achieved around the mass–air–mass resonance frequency (50–120 Hz). The obtained reductions in the transmitted sound pressure illustrate the potentials of HRs for improving the sound insulation characteristics of double glazed window. The experimental results also indicate that only tuning the HRs to the mass–air–mass resonance frequency does not guarantee the best possible insulation of the sound transmission.     

板结构的声辐射模态分析及其高分辨率法向振动速度重建

提出了一种基于声辐射模态的速度基向量构建方法,该速度基向量不受网格划分的影响,可用于高分辨率的板结构法向振动速度重建。首先对板表面稀疏网格的声辐射模态进行计算,再以声辐射模态和模态系数构建板法向振动速度分布的基向量,然后由声场测量声压求解基向量系数,最后由该系数和加密网格的速度基向量重建高分辨率的板法向振动速度分布。以简支板声源进行仿真计算,当测量声压信噪比为30 dB时,低频的法向振动速度重建误差最低可达3.7%;以固支板声源在消声室中进行实验验证,131.5 Hz振动频率下的重建误差低于7%。该方法实现了只需要少量声压测量点即可精确重建板声源更高分辨率的法向振动速度分布。      

薄膜型声学超材料对低频振动的隔声特性分析*

高效共振混合机工作频率为60 Hz,且系统处于共振,产生较大低频噪声。针对振动机械产生的有害噪声,分析了高效共振混合机低频高加速度共振混合过程的特点,得到了60 Hz低频声波穿透力强特点,相比传统的以吸声材料构建的50~100 mm厚度、隔声效果小于10 dB的隔声罩,分析了薄膜型声学超材料在低频减振降噪中的隔声特性。通过多物理场仿真分析,60 Hz时隔声量为31.4 dB,确定了硅橡胶弹性薄膜的预应力和质量块的面密度;采用3D打印机快速成型技术,构建了隔声实验装置,分析了独立隔声单元、面密度、薄膜尺寸等隔声特性规律。基于人耳在实际环境中感受到的噪声强度,提出了噪声衰减量和插入损失的分析方法,在距离声源380 mm和1000 mm的位置,60 Hz时隔声量分别为27 dB和38 dB。研究成果丰富了低频隔声特性理论,为薄膜型声学超材料的工程设计和优化提供了技术支撑。