Eu3+掺杂的铌酸钠钾陶瓷的制备及性能研究

采用固相烧结法制备了Eu³⁺掺杂的铌酸钠钾（KNN）陶瓷。用X射线粉末衍射仪、荧光光谱测试仪和LCR精确阻抗测试仪等对其结构、发光性能和介电性能进行表征。XRD结果显示样品为钙钛矿结构。荧光分析结果表明,致密度对KNN陶瓷材料发光性能有一定的影响,Eu³⁺掺杂量是影响其发光性能的重要因素。其中掺杂Eu摩尔分数为4%的样品在930℃焙烧后其发光最强,在396 nm紫外光激发下,发射光谱最强峰在614 nm,对应于Eu³⁺的⁵D₀-⁷F₂电偶极跃迁。样品经3 kV/cm、110℃极化30 min后进行压电性能检测,结果表明提高Eu³⁺掺杂量以及陶瓷的致密度,可改善压电性能。其中掺杂4%Eu的KNN压电常数D₃₃最大为98 pC/N,在1 kHz、100℃时,介电常数最小为217,介电损耗tanθ=0.199,且仍然保持较高的居里温度T_c=426℃。     

Er3+/Yb3+共掺的氧化镧钇透明陶瓷的光谱性能研究

采用传统无压烧结工艺制备了Yb³⁺/Er³⁺共掺的氧化镧钇透明陶瓷并对其光谱性能进行了研究.样品具有较大的吸收和发射截面.La₂O₃的添加使样品的荧光寿命(τ_s)与玻璃接近，当Yb³⁺和Er³⁺的掺杂量分别为5at%和0.5at%时，测得τ_s=9.65　ms.这种荧光寿命长、发射截面大和线宽窄的特性有利于微型、可集成化和大功率激光输出的实现. 关键词： 透明陶瓷 吸收光谱 发射光谱 荧光寿命     

Y2Ti2O7:Tm3+的制备及其发光性能研究

采用溶胶-凝胶法(Sol-gel)制备了不同烧结温度和Tm³⁺掺杂浓度的Y₂Ti₂O₇:xTm (x=0.005,0.01,0.03,0.05)荧光粉,分别采用X射线衍射分析仪(XRD)、透射电子显微镜(TEM)和荧光光谱仪对样品的晶型结构、形貌以及发光性能进行了表征。XRD结果表明,所得到的样品为单一立方相烧绿石结构。样品在361 nm紫外光激发下发射出 蓝光,其峰值波长为456 nm,对应于Tm³⁺的¹D₂→³F₄跃迁。1 000 ℃烧结的Y₂Ti₂O₇: 0.01Tm³⁺样品具有较好的发光性能。样品在456 nm处的相对发光强度随Tm³⁺掺杂浓度的增大先升高后降低,在Tm³⁺摩尔分数为1%时达到最大,即出现了浓度猝灭现象。     

Na0.25K0.25Bi0.5TiO3无铅压电陶瓷的介电特性研究

用固相反应法制备了Na_0.25K_0.25Bi_0.5TiO₃ (NKBT50)陶瓷，研究了该陶瓷在室温至400℃温度范围内的介电性能.发现该陶瓷的介电温谱与烧结气氛、极化状态有关.在空气中烧结的未极化样品在70℃附近存在介电和损耗峰，而极化后及在氧气氛中烧结的样品并不存在该介电、损耗峰.分析认为70℃的介电和损耗峰与氧空位形成的缺陷偶极子的极化弛豫有关.热激电流显示，陶瓷的去极化温度为225℃，与此相对应的介电、损耗峰也 关键词： 介电性能 氧空位 极化弛豫 钛酸铋钠钾     

(Na1/2Bi1/2)Cu3Ti4O12陶瓷的微观结构和电学性质

利用固相反应法在不同烧结温度条件下制备了一系列(Na_1/2Bi_1/2)Cu₃Ti₄O₁₂(NBCTO)陶瓷样品,研究了它们的晶体结构、微观组织结构、介电性质和复阻抗及其随温度的变化. 实验发现NBCTO陶瓷所呈现出的电学性质与CaCu₃Ti₄O₁₂陶瓷相应的电学性质非常类似. 烧结温度为990℃至1060℃范围的NBCTO陶瓷样品室 关键词： 高介电材料 介电性质 复阻抗 内阻挡层电容     

Dy掺杂对Sr2Bi4Ti5O18铁电陶瓷性能的影响

用传统固相烧结法制备了Sr₂Bi_4-xDy_xTi₅ O₁₈(SBDT-x, x=0—0.20)陶瓷样品. x射线衍射分析表明, 微量的Dy掺杂没有影 响Sr₂Bi₄Ti₅O₁₈(SBTi) 原有的层状钙钛 矿结构. 通过研究样品的介电特性, 发现Dy掺杂减小了材料的损耗因子, 降低了样品铁电- 顺电相转变的居里温度. 铁电性能测量结果表明, 随Dy含量的增加, SBDT-x系列样品的剩余 极化先增大, 后减小. 当Dy掺杂量为0.01时, 剩余极化达到最大值, 约为20.1 μC·cm^-2. 掺杂引起剩余极化的变化, 与材料中缺陷浓度、内应力以及晶格畸变程度等因 素有关, 是多种作用机理相互竞争的结果. (Bi₂O₂)²⁺ 层通常被看作是绝缘层和空间电荷库, 对材料的铁电性能起关键作用. 掺杂离子进入(Bi2O₂)²⁺层会导致铁电性能变差. 关键词： 2Bi₄Ti₅O₁₈陶瓷')" href="#">Sr₂Bi₄Ti₅O₁₈陶瓷 Dy掺 杂 铁电性能 居里温度     

Cr3+:Al2O3透明多晶陶瓷光谱特性分析

对透光性良好的Cr³⁺:Al₂O₃透明多晶陶瓷的光谱性能 进行了研究，其吸收光谱中吸收峰与单晶红宝石相一致，按吸收光谱和Tanabe-Sugano能级 图，算出其晶场强度参数D_q及Racah参数B分别为1792cm^-1， 689cm ^-1，D_q/B=2.6，陶瓷中Cr³⁺离子所处格位的晶体场强 比单晶弱一些，但Cr³⁺:Al₂O₃透明陶瓷仍属于强场晶 体材料；当Cr³⁺掺杂浓度到达0.8wt%时，陶瓷的发射谱仍保持较好的R线发射 ；随Cr³⁺掺杂浓度的增大，激发峰位发生“红移”.在Cr³⁺:Al₂O₃透明多晶陶瓷的荧光谱上，发现一个波长为670nm的发射峰，经激发 谱确认为Cr³⁺的发射峰. 关键词： 氧化铝 透明陶瓷 离子格位 光谱性质     

不同价态稀土元素Yb掺杂ZnO的电子结构和光学性质

基于密度泛函理论, 采用第一性原理平面波超软赝势法, 对六方纤锌矿结构的ZnO晶体和Yb²⁺, Yb³⁺分别掺杂ZnO晶体进行几何优化, 并在此基础上计算得到了未掺杂ZnO晶体及不同价态Yb元素掺杂ZnO体系的空间结构、 能带、电子态密度及光学性质.结果表明: 掺杂后体系形成能减少, 稳定性增加, 并引入了Yb-4f杂质能级. 掺杂不同价态的Yb元素对能带结构产生了不同的影响, 并且都使体系的光学性质发生了明显变化.与纯ZnO相比, Yb²⁺, Yb³⁺ 分别掺杂ZnO体系的介电函数虚部在0.46 eV处均出现新峰, 静态介电函数明显增大, 吸收带边均红移, 并在0.91 eV处出现较强吸收峰, 对产生这一现象的原因给出了定性的讨论. 关键词： 掺杂 ZnO 不同价态 第一性原理     

钨酸铅晶体中的偶极缺陷

在用阻抗谱研究PbWO₄（PWO）晶体的介电特性时发现，掺La³⁺的PW O晶体中存在典型的介电弛豫现象，它被归因于La³⁺进入Pb位并与铅空位V_Pb缔合 成偶极缺陷.这一结果不仅清楚地证明了PWO晶体中铅空位的存在，而且表明阻抗谱测试可以成为PWO晶体微结构研究的有力工具.以阻抗谱测试为主要工具，结合光吸收谱（包括红外谱）和x射线光电子能谱，阐明了在异价掺杂离子（3+，4+，5+以及3+和5+双掺）掺杂的PWO晶体中 关键词： 钨酸铅 偶极缺陷 异价掺杂 退火效应     

稀土掺杂Gd2Te4O11亚碲酸盐荧光粉的合成及其发光性能

采用水热法制备了一系列稀土Dy³⁺,Tb³⁺,Eu³⁺掺杂的极性Gd₂Te₄O₁₁(GTO)亚碲酸盐荧光粉.对样品的物相结构、形貌和热稳定性等进行了表征,测试了样品的发光性能.结果显示,所制样品均为单相,呈短杆状形貌,尺寸在微米量级,热稳定性能良好.对于GTO:Dy³⁺荧光粉,在紫外光激发下的发光主要位于黄绿光区,获得最强发光强度的掺杂浓度为2.5%,色坐标为(0.39,0.43);荧光衰减曲线表明GTO:Dy³⁺样品发光寿命随着掺杂浓度增大逐渐减小,与Dy³⁺离子间的交叉弛豫有关.对于GTO:Eu³⁺荧光粉,在紫外光激发下的发光主要位于红光和橙红光区,其发射强度随着Eu³⁺掺杂浓度的增大而增强.当掺杂浓度为10%时,样品发光的色坐标为(0.62,0.38),位于橙红光区,且样品的发光寿命几乎不受掺杂浓度影响.对于GTO:Tb³⁺     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.