He 离子注入引起的高纯钨硬化

完成了不同注量或温度下100 keV 的He 离子注入高纯钨的实验,并利用纳米压痕技术测量了材料的微观力学性能。所有注入样品的纳米硬度值都高于未注入样品的纳米硬度值。对于室温注入样品,随着注量的增加,样品抗弹性变形能力下降;当注量不高于5x1017 ions/cm2 时,钨的纳米硬度峰值随着注量的增加而增加;注量为1x1018 ions/cm2 的钨样品的纳米硬度峰值反而降低。高温注入样品的抗弹性变形能力优于室温注入样品的抗弹性变形能力;随着注入温度的增加,样品的平均纳米硬度值和弹性模量略有下降。分析讨论了He 注入钨硬化和抗弹性形变能力降低的可能原因。Tungsten has been selected as divertor materials in fusion reactors because of its high thermal conductivity,high melting point, low expansion coefficient and high threshold energy for sputtering etc. The paper presents the hardening behaviour of high pure tungsten by 100 keV He+ with different fluences from 5x1016 ions/cm2 to 1x1018ions/cm2 at room temperature, and with fluence of 1x1018 ions/cm2 at higher temperatures (400, 600 and 800 °C). The microscopic mechanical properties of these samples were investigated by nano-indentation technology. The results show that all of the implanted samples harden obviously. The reason for hardening may be that defects of interstitial dislocation loops or dense helium bubbles etc induced by helium implantation obstacle the movement of dislocation. The peak nanohardness of the samples increased with the fluences increasing when the fluence is not more than 5x1017 ions/cm2, while the nano-hardness value of the implanted sample with the fluence of 1x1018 ions/cm2 decreases and the nano-hardness changes little in the region of 50 nm to 200 nm from surface. For all the implanted samples with 1x1018 ions/cm2 at higher temperatures, their nano-hardness values are similar, but show a trend of decrease with increasing temperature.The reason may be the decrease of the defects’ density during implantation at higher temperatures. In addition, the capability of resisting deformation for the implanted tungsten reduces with increasing fluence and increases a little at higher temperatures.     

Krypton ion irradiation-induced amorphization and nano-crystal formation in pyrochlore Lu_2Ti_2O_7 at room temperature

Polycrystalline pyrochlore Lu2Ti2O7 pellets are irradiated with 600-ke V Kr3+ions up to a fluence of 1.45 ×1016Kr3+/cm2. Irradiation induced structural modifications are examined by using grazing incidence x-ray diffraction(GIXRD) and cross-sectional transmission electron microscopy(TEM). The GIXRD reveals that amorphous fraction increases with the increase of fluences up to 2 × 1015Kr3+/cm2, and the results are explained with a direct-impact model.However, when the irradiation fluence is higher than 2 × 1015Kr3+/cm2, the amorphous fraction reaches a saturation of~80%. Further TEM observations imply that nano-crystal is formed with a diameter of ~10 nm within the irradiation layer at a fluence of 4 × 1015Kr3+/cm2. No full amorphization is achieved even at the highest fluence of 1.45 × 1016Kr3+/cm2(~36 displacement per atom). The high irradiation resistance of pyrochlore Lu2Ti2O7 at higher fluence is explained on the basis of enhanced radiation tolerance of nano-crystal structure.     

注氦尖晶石的红外光谱研究

利用傅立叶变换红外光谱仪对注He尖晶石样品随退火温变化而引起光吸收性能的变化进行了研究。 发现尖晶石样品在626.4 cm-1附近的吸收峰随注入剂量的增加向小波数方向移动, 而在随后退火过程该吸收峰随退火温度的增加而向大波数方向回复。 该吸收峰的回复行为依赖于注入剂量和退火温度。 认为在626.4 cm-1附近吸收峰随注入剂量和退火温度的这种变化与尖晶石中He的俘获以及释放有关。 The infrared absorption behavior of helium implanted spinel with annealing temperature was studied by Fourier transformed infrared (FTIR) spectroscopy. It was found that the absorbance peak at 626.4 cm-1 shifted to smaller wave numbers with the increase of implantation fluence, while on subsequent annealing the absorbance peak shifted back to larger wave numbers with the increase of annealing temperature. The shift of the peak at 626.4 cm-1 with He implantation/annealing is considered to be related with the trapping and release of helium atoms in lattice sites in the spinel crystal.     

Be-composition effect on structure, electronic and optical properties of BexZn1-xO alloys

This paper carries out first principles calculation of the structure,electronic and optical properties of Be x Zn 1 x O alloys based on the density-functional theory for the compositions x = 0.0,0.25,0.5,0.75,1.0.The lattice constants deviations of alloys obey Vegard’s law well.The Be x Zn 1 x O alloys have the direct band gap(Γ-Γ) character,and the bowing coefficients are less than the available theoretical values.Moreover,it investigates in detail the optical properties(dielectric functions,absorption spectrum and refractive index) of these ternary mixed crystals.The obtained results agree well with the available theoretical and experimental values.     

Effect of Mg and Fe Doping on Optical Absorption of LiNbO3 Crystal through First Principles Calculations

Using first principles calculations, we investigate the structural, optical, and electronic properties of LiNbO3 （LN） and M doped LN （M=Mg, Fe）. The density of states are calculated to analyze the effect of doping Mg and Fe ions on the absorption spectra and electronic properties of LN. The results show an ultraviolet shift in the optical absorption edge of Mg-doped LN compared with that of intrinsic LN. On the contrary, the absorption edge of Fe-doped LN crystal reveals a red shift. The optical absorption spectra show an improved optical response in the visible range for Mg-doped LN, which significantly differs from that obtained for Fe-doped LN. The electronic excitations from the valence band to the conduction band of LN leads to an improved optical absorption response in the visible region as observed experimentally. The obvious changes of the doped LN crystal are found in some cases, which provide a helpful guide for preparing doped LN crystal.     

Effect of Pulse Width and Fluence of Femtosecond Laser on Electron--Phonon Relaxation Time

The electron phonon relaxation time as functions of pulse width and fluence of femtosecond laser is studied based on the two-temperature model. The two-temperature model is solved using a finite difference method for copper target. The temperature distribution of the electron and the lattice along with space and time for a certain laser fluence is presented. The time-dependence of lattice and electron temperature of the surface for different pulse width and different laser fluence are also performed, respectively. Moreover, the variation of heat-affected zone per pulse with laser Auence is obtained. The satisfactory agreement between our numerical results and experimental data indicates that the electron-phonon relaxation time is reasonably accurate with the influences of pulse width and Auence of femtosecond laser.     

Nonlinear optical switching and all-figures of merit in Bi2S3-xSex/PMMA nanocomposite films investigated by Z scan under visible CW laser

Bi2S3-xSex/poly(methyl methacrylate)(PMMA)nanocomposite films were prepared using microwave assisted synthesis with different compositions of x.Crystal structure,surface morphology,and optical properties were investigated to characterize the prepared nanocomposite films.The crystallinity and optical band gap of the prepared Bi2S3-xSex/PMMA were affected by x.The prepared samples showed a blue shift in the absorption edge.The laser power dependent nonlinear refraction and absorption of Bi2S3-xSex/PMMA nanocomposite films were investigated by using the Z-scan technique.The optical nonlinearity of the nanocomposite films exhibited switchover from negative nonlinear refraction to positive nonlinear refraction to negative nonlinear refraction effects,and from saturable absorption to reverse saturable absorption to saturable absorption with an increase and decrease in the composition.An interesting all-optical figure of merit was reported to assess the nanocomposite films for a practical device.It was calculated that the device all-figures of merit were based on the nonlinear response,which is important for the all-optical switching device.The results demonstrate that the optimized all-optical figures of merit can be achieved by adjusting the composition and input laser power,which can be used for the design of different all-photonic devices,and the results of nonlinear switching behavior can open new possibilities for using the nanocomposite films in laser Q-switching and mode-locking.     

Preparation and Optical Properties of SnO2／SiO2 Nanocomposite

SnO2/SiO2 nanocomposites have been prepared by the soaking-thermal-decomposing method, tin oxide nanoparticles are uniformly dispersed in the mesopores of silica. The optical absorption edge of the obtained nanocomposite presents a redshift compared with bulk tin oxide, With the increasing annealing temperature during the procedure of the sample preparation, the optical absorption edge of the sample moves to shorter wavelength (blueshift). These optical properties can be ascribed to the amorphous structure and band defects of surface layers of the tin oxide nanoparticles.     

Electronic and optical properties of CdS/CdZnS nanocrystals

Cd1-x ZnxS nanocrystals are prepared by a co-precipitation method with different atomic fractions of Zn.The texture,structural transformation and optical properties with increasing x value in Cd1-x ZnxS are studied with scanning electron microscopy,electron diffraction patterning,and absorption spectra respectively.Quantum confinement in a strained CdS/Cd1-xZnxS related nanodot with various Zn content values is investigated theoretically.Binding energies on exciton bound CdS/CdxZn1-xS quantum dot are computed,with consideration of the internal electric field induced by the spontaneous and piezoelectric polarizations,and thereby the interband emission energy is calculated as a function of the dot radius.The optical band gap from the UV absorption spectrum is compared with the interband emission energy computed theoretically.Our results show that the average diameter of composite nanoparticles ranges from 3 nm to 6 nm.The X-ray diffraction pattern shows that all the peaks shift towards the higher diffracting angles with an increase in Zn content.The lattice constant gradually decreases as the Zn content increases.The strong absorption edge shifts towards the lower wavelength region and hence the band gap of the films increases as the Zn content increases.The values of the absorption edge are found to shift towards the shorter wave length region and hence the direct band gap energy varies from 2.5 eV for the CdS film and 3.5 eV for the ZnS film.Our numerical results are in good agreement with the experimental results.     

Effects of Vacuum on Fused Silica UV Damage

Damage points induced by 355 nm laser irradiation increase more quickly on the surface of fused silica in vacuum of about 10^-3 Pa than in atmospheric air at the same fluence. The larger concentration of point defects in vacuum is confirmed by photoluminescence intensity. X-ray photoelectron spectroscopy and infrared absorption indicate the formation of sub-stoichiometric silica on the surface. The degradation mechanism of fused silica in vacuum is discussed.     

Ne离子束辐照引起Gd2Ti2O7烧绿石体积肿胀效应研究

在液氮低温下用400 keV的Ne2+离子束对Gd₂Ti₂O₇多晶烧绿石进行了辐照实验研究, 离子束辐照量范围为5×1014—1×1016ions/cm2。利用掠X射线衍射技术对样品辐照层的结构变化进行了分析表征, X射线的掠射角分别为γ=0.25°, 0.5°, 1°和3°。结果表明: 在该实验条件的离子束辐照下, Gd₂Ti₂O₇辐照层会发生明显的体积肿胀效应, 体积肿胀程度随入射离子束辐照量的增大而增大; 在同一辐照量下, 辐照层的体积肿胀程度也随X射线入射角的增大而增大。当辐照量达到1×1016ions/cm2时, 辐照层发生非晶化相变。Polycrystalline pyrochlore Gd₂Ti₂O₇ compounds were irradiated with 400 keV Ne2+ ions at cryogenic temperature (~77 K). The irradiation fluences was ranging from 5×1014 to 1×1016 ions/cm2, corresponding to a peak ballistic damage dose of ~0.16 to 3.3 displacements per atom . Irradiation\|induced structural evolution was examined using grazing incidence X\|ray diffraction (GIXRD) at angles from 0.25° to 3° degrees. It was found that the lattice parameter increases as a function of (1) X\|ray incident angle and (2) ion irradiation fluence, suggesting that the irradiated layer is volumetrically swelled compared with the underlying un\|irradiated substrate. At ion fluence of 1×1016 ions/cm2, the irradiation layer was found to be amorphous.     

He注入单晶Si表面形貌的变化研究

沿Si的（100）面注入He离子, 能量为30 keV、 剂量为5×1016 ions/cm2。 注入后样品切成几块, 在真空炉中分别做退火处理, 退火温度从600 ℃到1 000 ℃, 退火时间均为30 min。 利用原子力显微镜研究了各个样品表面形貌的演化。 发现样品表面形貌与退火温度相关联。 假设在气泡中He原子与空位的比值很高, 导致样品内部存在高压的He泡, 从而使样品表面形貌发生变化。 探讨了在Si中He泡随退火温度的演化和He原子在材料中的释放机制及其对表面的影响。     

Photoluminescence and optical properties of He ion bombarded ultra-high molecular weight polyethylene

Ion bombardment is a suitable tool to improve the physical and chemical properties of polymer surface. In this study UHMWPE samples were bombarded with 130 keV He ions to the fluences ranging from 1 × 10¹² to 1 × 10¹⁶ cm⁻². The untreated and ion beam modified samples were investigated by photoluminescence, and ultraviolet-visible (UV-vis) spectroscopy. Remarkable decrease in integrated luminescence intensity with increasing ion fluences was observed. The reduction in PL intensity with increase of ion fluence might be attributed to degradation of polymer surface and formation of defects. The effect of ion fluence on the optical properties of the bombarded surfaces was characterized. The values of the optical band gap E_g, and activation energy E_a were determined from the optical absorption. The width of the tail of the localized states in the band gap (E_a) was evaluated using the Urbach edge method. With increasing ion fluences a decrease in both the energy gap and the activation energy were observed. Increase in the numbers of carbon atoms (N) in a formed cluster with increasing the He ion fluence was observed.     

EMR and optical study of Mn2+ doped potassium trihydrogen selenite

The EMR study of Mn2+ doped potassium trihydrogen selenite is performed and the site of Mn2+ in the lattice is discussed. The zero field parameters providing good fit to the observed EMR spectra are estimated. The spin-Hamiltonian parameters g, A, B, D, and a are (2.0003 +/- 0.0002), (31 +/- 2) x 10(-4), (20 +/- 2) x 10(-4), (87 +/- 2) x 10(-4), and (-9 +/- 1) x 10(-4) cm(-1), respectively. The percentage of covalency of the metal-ligand bond is also determined. The optical absorption study suggests the lattice distortion in the crystal. The electron repulsion and crystal field parameters having good fit to the observed optical spectra are evaluated. The band positions are fitted with the Racah parameters (B and C), the cubic crystal field splitting parameters (Dq), and the Trees correction (alpha). The values of B, C, Dq, and alpha are 871, 2967, 670, and 76 cm(-1), respectively.     

Role of surface elastic relaxations in an O-induced nanopattern on Pt(110)-(1 x 2)

Scanning tunneling microscopy shows that a nanopattern forms as the Pt(110)-(1 x 2) surface is exposed to oxygen at room temperature or above. The nanopattern consists of [11[over]0] oriented O-induced stripes assembling into a (11 x 2) superstructure at high O coverage. The stripes form because the O adsorption energy increases by expanding the Pt lattice along the ridges of the surface as compared to the bulk. From interplay with density functional theory calculations, we show that the O-induced nanoscale periodicity is caused by short-ranged elastic relaxations confined to the surface.     

Collision-induced vibrational energy transfer: K2[1(1) sigmau+ (nu'=2)]+He, H2-->K2[1(1) sigmau+(nu'=1,3)]+He, H2

Collisional energy transfer processes K2[1(1) sigmau+ (nu'=2)]+He, H2-->K2[1(1) sigmau+(nu'=1,3)]+He, H2 were studied by laser induced fluorescence under gas cell conditions. During the experiments, the cell temperature was kept constant at 420K. The buffer gas pressure was varied over the range from 40 to 250 Pa, Kz molecules were irradiated with pulses of radiation from an OPO laser, populating K2[1(1) sigmau+ (nu'=2)] by photon absorption. The resulting fluorescence included the direct component emitted in the decay of the optically excited state and the sensitized components arising from collisionally populated states. The decay signal of time-resolved fluorescence from 1(1) sigmau+ (nu'=2)]-->1(1) sigmag+(nu"=0) transition was monitored. In the early period after excitation, only very little population in states v'= 1 or 3 had yet accumulated, the rate of collisional activation to the state nu'=2 was negligible. The decay curve of the nu' = 2-->nu" = 0 was treated as a single exponential function. From the measurement of the time-resolved fluorescence, the semilog plot was shown. The slope yielded the effective lifetime of the nu' = 2--> nu' = 0 transition. Based on the Stern-Volmer equation, the radiative lifetime (36 +/- 7) ns was obtained. The total cross sections for deactivation of 1(1) sigmau1 (nu'=2) state by means of collisions with He and H2 are (3.0 +/- 0.5) x 10(-16) cm2 and (6.4 +/- 1.2) x 10(-15) cm2, respectively. The radiative lifetimes of 1(1) sigmau+(nu' = 1,3) states can also be determined through time-resolved fluorescence in pure K vapor. The time-integrated intensities of 1(1)sigmau+(nu' = 1,2,3)-->1(1) sigmag+(nu"=0) transition at different He or Hz pressure were measured. The ratio of fluorescence intensities versus 1/P(He, H2) can be fitted by a straight line. The slopes yield the cross sections sigma(nu'=2-->nu'=1) = (1.4 +/- 0.5) x 10(-16) cm2 and (3.2 +/- 1.0) x 10(-15) cm2; sigma(nu'=2-->nu'=3)= (1.2 +/- 0.4) x 10(-16) cm2 and (2.6 +/- 0.9) x 10(-15) cm2 for He and H2, respectively. Cross sections for the effective quenching of the nu' = 1,2,3 states were also determined. To our knowledge, the cross-sections for these processes are reported for first time.     

Optical absorption spectrum of gold atoms deposited on SiO(2) from cavity ringdown spectroscopy

The optical properties of gold atoms supported on amorphous silica (alpha-SiO2) were studied experimentally and theoretically in the visible range. Samples were prepared in situ by depositing Au atoms at low coverages (5 x 10(12) cm(-2)) in UHV, and the optical absorption spectra were recorded by cavity ringdown spectroscopy. The atomic absorption bands can be attributed to gold atoms trapped at [triple bond] Si-O(.-) and [triple bond]Si-O(-) defect sites. The absence of optical transitions typical for Au(2) shows that the atoms are efficiently anchored at these defect sites, preventing diffusion and aggregation. Furthermore, these experimental results reveal that it is now possible to study optical properties of well-defined nanostructures at surface coverages as low as 5 x 10(11) cm(-2).     

氮气退火对二氧化钛薄膜光学性能的影响

 提出了一种利用离子注入和后续退火制备氮掺杂TiO₂薄膜的方法。首先在室温下向石英玻璃中注入Ti离子,随后在氮气中退火到900 ℃,从而制备了氮掺杂的玻璃基TiO₂薄膜。SRIM2006程序模拟和卢瑟福背散射谱（RBS）研究表明注入离子从样品表面开始呈高斯分布,实验结果和模拟结果吻合很好。X射线光电子能谱（XPS）研究结果表明注入态样品中形成了金属Ti和TiO₂,900 ℃退火后金属Ti转变成TiO₂,同时N原子替代少量的晶格O原子形成了O－Ti－N化合物。紫外-可见吸收光谱（UV-Vis）结果显示,当退火温度至500 ℃时,在吸收光谱中开始出现TiO₂的吸收边,随退火温度升高到900 ℃,由于O－Ti－N化合物形成,TiO₂的吸收边从3.98 eV红移到3.30 eV,TiO₂吸收边末端延伸到可见光区,在可见光区的吸收强度明显增加。     

Surface chemical disorder and lattice strain of GaN implanted by 3-MeV Fe10+ ions

Chemical disorder on the surface and lattice strain in GaN implanted by Fe¹⁰⁺ ions are investigated. In this study, 3-MeV Fe¹⁰⁺ ions fluence ranges from 1×10¹³ ions/cm² to 5×10¹⁵ ions/cm² at room temperature. X-ray photoelectron spectroscopy, high-resolution x-ray diffraction, and high-resolution transmission electron microscopy were used to characterize lattice disorder. The transition of Ga-N bonds to oxynitride bonding is caused by ion sputtering. The change of tensile strain out-of-plane with fluence was measured. Lattice disorder due to the formation of stacking faults prefers to occur on the basal plane.