纳米流体对流换热机理分析

考虑在纳米流体中纳米颗粒做布朗运动引起的对流换热, 基于纳米颗粒在纳米流体中遵循分形分布, 本文得到纳米流体对流换热的机理模型. 本解析模型没有增加新的经验常数, 从该模型发现纳米流体池沸腾热流密度是温度、纳米颗粒的平均直径、 纳米颗粒的浓度、纳米颗粒的分形维数、沸腾表面活化穴的分形维数、基本液体的物理特性的函数. 对不同的纳米颗粒浓度和不同的纳米颗粒平均直径与不同的实验数据进行了比较, 模型预测的结果与实验结果相吻合. 所得的解析模型可以更深刻地揭示纳米流体对流换热的物理机理.     

A fractal model for heat transfer of nanofluids by convection in a pool

Based on the fractal distribution of nanoparticles, a fractal model for heat transfer of nanofluids is presented in the Letter. Considering heat convection between nanoparticles and liquids due to the Brownian motion of nanoparticles in fluids, the formula of calculating heat flux of nanofluids by convection is given. The proposed model is expressed as a function of the average size of nanoparticle, concentration of nanoparticle, fractal dimension of nanoparticle, temperature and properties of fluids. It is shown that the fractal model is effectual according to a good agreement between the model predictions and experimental data.     

A fractal study for nucleate pool boiling heat transfer of nanofluids

In this paper, a fractal model for nucleate pool boiling heat transfer of nanofluids is developed based on the fractal distribution of nanoparticles and nucleation sites on boiling surfaces. The model shows the dependences of the heat flux on nanoparticle size and the nanoparticle volume fraction of the suspension, the fractal dimension of the nanoparticle and nucleation site, temperature of nanofluids and properties of fluids. The fractal model predictions show that the natural convection stage continues r...     

Subcooled pool boiling heat transfer in fractal nanofluids:A novel analytical model

A novel analytical model to determine the heat flux of subcooled pool boiling in fractal nanofluids is developed. The model considers the fractal character of nanofluids in terms of the fractal dimension of nanoparticles and the fractal dimen- sion of active cavities on the heated surfaces; it also takes into account the effect of the Brownian motion of nanoparticles, which has no empirical constant but has parameters with physical meanings. The proposed model is expressed as a function of the subcooling of fluids and the wall superheat. The fractal analytical model is verified by a reasonable agreement with the experimental data and the results obtained from existing models.     

纳米颗粒聚集形态对纳米流体导热系数的影响

纳米流体中悬浮的纳米颗粒可以增强其导热性能已经得到广泛认可,然而纳米流体颗粒增强传热的机理目前尚不清楚.研究表明,纳米颗粒的聚集是纳米流体导热系数增大的重要机制,而且纳米颗粒聚集的形态对纳米流体的导热系数有重要影响,但是目前的导热系数模型大多是建立在Maxwell有效介质理论的"静态"和"均匀分散"假设基础上.本文用平衡分子动力学模拟Cu-Ar纳米流体,采用Green-Kubo公式计算导热系数,采用Schmidt-Ott关系式计算不同聚集形态下的分形维数.对比导热系数与分形维数可以发现:在相同体积分数下,较低的分形维数会有更高的导热系数,分析了分形维数与导热系数的定量关系.此外,通过径向分布函数可以看出纳米颗粒紧密聚集与松散聚集的差异,基液分子在纳米颗粒附近的纳米薄层中处于动态平衡状态.研究结果有助于理解纳米颗粒聚集形态对导热系数的影响机理.     

小通道扁管内纳米流体流动与传热特性

建立了测量小通道扁管内纳米流体流动与对流换热性能的实验系统,测量了不同粒子体积份额的水-Cu纳米 流体的管内对流换热系数和摩擦阻力系数,实验结果表明,在相同雷诺数条件下,小通道扁管内纳米流体的对流换热系数 大于纯液体,且随粒子的体积份额的增加而增大,而纳米流体的阻力系数并未明显增大。     

纳米流体介质导热机理初探

纳米流体导热行为具有许多奇异的特性，结合纳米流体的特点和微尺度传热学原理，研究了 热流在纳米颗粒内波动式及非限域的热传导特性、纳米颗粒在悬浮液内的布朗运动、颗粒- 液体界面上液膜层原子的有规则排列、以及纳米颗粒的团簇形成及移动等四方面因素对纳米 流体导热系数的影响. 关键词： 纳米流体 导热     

纳米流体的聚集结构和导热系数模拟

本文根据布朗运动理论模拟纳米粒子在流体中的聚集过程，运用分形理论描述纳米粒子团的结构．考虑纳米粒子的运动传热，建立纳米流体的导热系数模型，理论预测值与实验结果显现了良好的一致性。     

Physics and mechanics of heat exchange processes in nanofluid flows

Nanofluids present a new type of dispersed fluids consisting of a carrier fluid and solid nanoparticles. Unusual properties of nanofluids, particularly high thermal conductivity, make them eminently suitable for many thermophysical applications, e.g., for cooling of equipment, designing of new heat energy transportation and production systems and so on. This requires a systematic study of heat exchange properties of nanofluids. The present paper contains the measurement results for the heat transfer coefficient of the laminar and turbulent flow of nanofluids on the basis of distilled water with silica, alumina and copper oxide particles in a minichannel with circular cross section. The maximum volume concentration of particles did not exceed 2%. The dependence of the heat transfer coefficient on the concentration and size of nanoparticles was studied. It is shown that the use of nanofluids allows a significant increase in the heat transfer coefficient as compared to that for water. However, the obtained result strongly depends on the regime of flow. The excess of the heat transfer coefficient in the laminar flow is only due to an increase in the thermal conductivity coefficient of nanofluid, while in the turbulent flow the obtained effect is due to the ratio between the viscosity and thermal conductivity of nanofluid. The viscosity and thermal conductivity of nanofluids depend on the volume concentration of nanoparticles as well as on their size and material and are not described by classical theories. That is why the literature data are diverse and contradictory; they do not actually take into account the influence of the mentioned factors (size and material of nanoparticles). It has been shown experimentally and by a molecular dynamics method that the nanofluid viscosity increases while the thermal conductivity decreases with the decreasing dispersed particle size. It is found experimentally for the first time that the nanofluid viscosity coefficient depends on the particle material. The higher is the density of particles, the higher is the thermal conductivity coefficient of nanofluid.     

Investigating the effects of nanoparticles mean diameter on laminar mixed convection of a nanofluid through an inclined tube with circumferentially nonuniform heat flux

In this study, laminar mixed convection of a water-based nanofluid containing Al₂O₃ nanoparticles in an inclined copper tube, which is heated at the top half surface, is investigated numerically. A heat conduction mechanism through the tube wall was implemented. Three-dimensional equations using a two-phase mixture model were solved to investigate the hydrodynamic and thermal behaviors of the nanofluid over a wide range of nanoparticle volume fractions. To verify the model, the results were compared with previous works and a good agreement between the results was observed. The effect of nanoparticles diameter on the hydrodynamic and thermal parameters over a wide range of Grashof numbers is presented and discussed for a particle volume fraction and Reynolds number. It is shown that the diameter of nanoparticles affects the particle distribution in the cross section perpendicular to the tube axis, heat transfer coefficient, and shear stress.     

粗糙表面形貌对微尺度流动换热的影响

基于分形几何定量描述了多尺度自仿射的粗糙表面形貌,建立了微通道内层流流动换热的理论模型并对表面形貌的影响进行了数值模拟.研究表明,自仿射分形维数直接反映了表面轮廓的不规则度,对于两个具有相同统计粗糙度的轮廓,可能存在不同的分形维数;与常规尺度通道不同,雷诺数、粗糙高度和粗糙表面分形维数都对微通道内层流流动换热有着重要影...     

方腔内Cu/Al2O3水混合纳米流体自然对流的格子Boltzmann模拟

纳米流体作为一种较高的导热介质, 广泛应用于各个传热领域. 鉴于纳米颗粒导热系数和成本之间的矛盾, 本文提出了一种混合纳米流体. 为了研究混合纳米流体颗粒间相互作用机理和自然对流换热特性, 在考虑颗粒间相互作用力的基础上, 利用多尺度技术推导了纳米流体流场和温度场的格子Boltzmann方程, 通过耦合流动和温度场的演化方程, 建立了Cu/Al₂O₃水混合纳米流体的格子Boltzmann模型, 研究了混合纳米流体颗粒间的相互作用机理和纳米颗粒在腔体内的分布. 发现在颗粒间相互作用力中, 布朗力远远大于其他作用力, 温差驱动力和布朗力对纳米颗粒的分布影响最大. 分析了纳米颗粒组分、瑞利数对自然对流换热的影响, 对比了混合纳米流体(Cu/Al₂O₃-水)与单一金属颗粒纳米流体(Al₂O₃-水)的自然对流换热特性, 发现混合纳米流体具有更强的换热特性.     

ZrO2纳米流体的对流换热系数测定及机理浅析

建立了测量圆管内纳米流体流动与传热性能的实验系统,测量了不同粒子浓度的ZrO2/水纳米流体在雷诺数为3 000～18 000范围内的管内对流换热系数以及不同位置处纳米流体对流换热系数的变化情况.实验结果显示,在液体中添加纳米粒子显著增大了液体的管内对流换热系数,例如,在相同雷诺数时,与纯水相比,如果纳米粒子的质量浓度从1.6%增大到4.1%,则纳米流体的对流换热系数增加的比例从1.09增大到1.2.此外,从颗粒的浓度、粒径两方面分析纳米流体强化传热的机理.     

含不同形状内热源的圆管内纳米流体自然对流及换热数值研究

采用格子玻尔兹曼方法对有三种恒温热源（圆形、三角形、方形）参与的圆管内纳米流体（铜-水）自然对流进行数值研究。主要研究瑞利（Ra）数,纳米颗粒体积分数以及热源几何形状等控制参数对纳米流体的流动与传热的影响。结果发现纳米颗粒体积分数的增加有利于强化传热,且在Ra数较小时,平均努塞尔（Nu）数增加的幅度要优于Ra数较大的情况。在所研究的控制参数范围内,方形热源的平均Nu数最大。根据数值结果给出不同热源表面的平均Nu数、纳米颗粒体积分数、Ra数三者之间的函数关系式,该函数关系可为此类工程的设计提供理论指导。     

纳米流体对流换热的实验研究

建立了测量纳米流体对流换热系数的实验系统,测量了不同粒子体积份额的水-Cu纳米流体在层流与湍流状态下的管内对流换热系数,实验结果表明,在液体中添加纳米粒子增大了液体的管内对流换热系数,粒子的体积份额是影响纳米流体对流换热系数的因素之一。综合考虑影响纳米流体对流换热的多种因素,提出了计算纳米流体对流换热系数的关联式。     

Thermal conductivity of nanofluids and size distribution of nanoparticles by Monte Carlo simulations

Nanofluids, a class of solid–liquid suspensions, have received an increasing attention and studied intensively because of their anomalously high thermal conductivites at low nanoparticle concentration. Based on the fractal character of nanoparticles in nanofluids, the probability model for nanoparticle’s sizes and the effective thermal conductivity model are derived, in which the effect of the microconvection due to the Brownian motion of nanoparticles in the fluids is taken into account. The proposed model is expressed as a function of the thermal conductivities of the base fluid and the nanoparticles, the volume fraction, fractal dimension for particles, the size of nanoparticles, and the temperature, as well as random number. This model has the characters of both analytical and numerical solutions. The Monte Carlo simulations combined with the fractal geometry theory are performed. The predictions by the present Monte Carlo simulations are shown in good accord with the existing experimental data.     

Transient electrohydrodynamic convective flow and heat transfer of MWCNT - Dielectric nanofluid in a heated enclosure

A computational research was performed to analyze the electrohydrodynamic (EHD) convective heat transfer in a differentially heated dielectric-MWCNT nanofluid layer. The study was conducted on a square enclosure subjected to a temperature gradient between these two vertical walls as well as a potential difference between these horizontal walls. The enclosure was filled with MWCNT oil-based nanofluid; the MWCNT nanoparticles were dispersed in a perfectly insulating thermal oil with a volume fraction of hardly exceeded 0.4%. The governing equations were derived with the assumption of homogeneous nanofluid and were solved with employing finite volume method. Based on the obtained results, it was found that the increase of Rayleigh number, electric Rayleigh number and nanoparticle concentration enhanced the heat transfer. For high thermal and electric Rayleigh number values, the flow and heat transfer became time dependent and accordingly a frequency study was also performed. It was found that the inclusion of an electric field with the addition of nanoparticles led to a significant heat transfer enhancement of about 43%.     

池沸腾传热的数学分析

在统计方法的基础上,对于池沸腾换热的传热机理提出了一个数学模型. 在没有增加新的经验常数的条件下,从该模型中可得到池沸腾热流密度是壁面过热度、活化穴最小与最大尺寸、流体的接触角与流体物理特性的函数. 该模型可以较好地解释润湿性如何影响沸腾热流密度. 对不同的接触角,模型预测的结果与实验相符合. 关键词： 池沸腾 传热 数学模型     

抛物槽式太阳能集热器内合成油基纳米流体传热特性的数值模拟

对Al₂O₃-合成油纳米流体在槽式太阳能集热管内的传热特性进行流体动力学数值模拟,重点考察纳米流体导热系数模型的影响。通过与管内Nusselt数半经验模型的预测结果对比,表明使用考虑布朗运动的纳米流体导热系数模型可较好地预测集热管内传热特性。研究表明纳米颗粒与流体基液的相对运动具有促进集热管内传热的作用。最后,定量研究纳米颗粒添加量对提高基础流体平均传热系数的影响,显示纳米流体在太阳能集热器中具有巨大应用潜力。