Effect of sintering temperature and the particle size on the structural and magnetic properties of nanocrystalline Li0.5Fe2.5O4

Sintering temperature and particle size dependent structural and magnetic properties of lithium ferrite (Li_0.5Fe_2.5O₄) were synthesized and sintered at four different temperatures ranging from 875 to 1475 K in the step of 200 K. The sample sintered at 875 K was also treated for four different sintering times ranging from 4 to 16 h. Samples sintered at 1475 K have the cubic spinel structure with a small amount of α-Fe₂O₃ (hematite) and γ-Fe₂O₃ (maghemite). The samples sintered at≤1275 K do not show hematite and maghemite phases and the crystals form the single phase spinel structure with the cation ordering on octahedral sites. Particle size of lithium ferrite is in the range of 13-45 nm, and is depend on the sintering temperature and sintering time. The saturation magnetization increased from 45 to 76 emu/g and coercivity decreases from 151 to 139 Oe with an increase in particle size. Magnetization temperature curve recorded in ZFC and FC modes in an external magnetic field of 100 Oe. Typical blocking effects are observed below about 244 K. The dielectric constant increases with an increase in sintering temperature and particle size.     

相分布和晶粒尺寸对Nd2Fe14B/ɑ-Fe纳米复合永磁材料矫顽力的影响

本文采用统计平均方法研究了软、硬磁性晶粒尺寸及相分布对Nd2Fe14B/α-Fe纳米复合永磁材料矫顽力的影响。计算结果表明：对于单相纳米硬磁材料，磁体矫顽力随着硬磁性晶粒尺寸的减小而降低；对于软、硬两磁性相组成的Nd2Fe14B/a-Fe纳米复合永磁材料，两相的随机分布将导致磁体矫顽力随硬磁性晶粒尺寸的减小呈现极大值。本文的计算结果还表明当硬磁性晶粒尺寸大于软磁性晶粒的最佳尺寸时(15nm)，具有多层膜结构的Nd2Fe14B/a-Fe纳米复合永磁材料将比两相随机分布时具有更大的矫顽力。     

非晶Fe73.5Cu1Nb3Si13.5B9合金激光纳米化的超精细结构研究

在CO₂激光功率为50—300W、扫描速度为20mm/s、激光散光斑为20mm照射条件下 ，诱导非 晶Fe_735Cu₁Nb₃Si_135B9带中发生结构重组，产生定量纳米α-F e(Si)晶相形成双相组织结构材料. 利用穆斯堡尔谱研究了非晶Fe_735C u₁Nb₃Si_135B₉合金激光纳米化的 超精细结构. 实验结果表明，激光诱导非晶 Fe_735Cu₁Nb₃Si_135B ₉纳米化后，其超精细磁场的分布随 着激光功率变 化由单峰向双峰变化，在高功率辐照时， 出现了双峰分布，并且峰位向高场移动. 高激光 功率辐照非晶Fe_735Cu₁Nb₃Si_{135B9合金纳米晶化相有四种超精细结 构，即2个超精细磁场较小的初晶相和2个超精细磁场较大的纳米晶化相. 其中超精细磁场较 大(17—25MA/m)的α-Fe(Si)相为DO3结构. 关键词： 激光 纳米晶α-Fe（Si) 735}Cu₁Nb< sub>3Si_135B₉')" href="#">非晶Fe_735Cu₁Nb< sub>3Si_135B₉ 超精细结构 超精细磁场     

Synthesis and magnetic properties of hard magnetic (CoFe2O4)-soft magnetic (Fe3O4) nano-composite ceramics by SPS technology

CoFe₂O₄/Fe₃O₄ nano-composite ceramics were synthesized by Spark Plasma Sintering. The X-ray diffraction patterns show that all samples are composed of CoFe₂O₄ and Fe₃O₄ phases when the sintering temperature is below 900 °C. It is found that the magnetic properties strongly depend on the sintering temperature. The two-step hysteresis loops for samples sintered below 500 °C are observed, but when sintering temperature reaches 500 °C, the step disappears, which indicates that the CoFe₂O₄ and Fe₃O₄ are well exchange coupled. As the sintering temperature increases from 500 to 800 °C, the results of X-ray diffractometer indicate the constriction of crystalline regions due to the ion diffusion at the interfaces of CoFe₂O₄/Fe₃O₄ phases, which have great impact on the magnetic properties.     

Crystallization of single-phase nanocrystalline Nd10.8Dy1.5Fe79.7(NbZrCu)2.0B6.0 ribbons

The crystallization of single-phase nanocrystalline Nd_10.8Dy_1.5Fe_79.7(NbZrCu)_2.0B_6.0 ribbons has been investigated. The as-spun ribbons are mainly composed of an amorphous matrix with a small amount of α-Fe, Nd₂Fe₁₄B and/or other crystallization phases. Cu-enriched clusters with different sizes have been found in the as-spun ribbons. These clusters almost disappear after crystallization, which can possess effects on the refinement of grains.     

Synthesis of (Mg0.476Mn0.448Zn0.007)(Fe1.997Ti0.002)O4 powder and sintered ferrites by high energy ball-milling process

(Mg_0.476Mn_0.448Zn_0.007)(Fe_1.997Ti_0.002)O₄ nanocrystalline powder prepared by high energy ball-milling process were consolidated by microwave and conventional sintering processes. Phases, microstructure and magnetic properties of the ferrites prepared by different processes were investigated. The (Mg_0.476Mn_0.448Zn_0.007)(Fe_1.997Ti_0.002)O₄ nanocrystalline powder could be prepared by high energy ball-milling process of raw Fe₃O₄, MnO₂, ZnO, TiO₂ and MgO powders. Prefired and microwave sintered ferrites could achieve the maximum density (4.86 g/cm⁻³), the average grain size (15 μm) was larger than that (10 μm) prepared by prefired and conventionally sintered ferrites with pure ferrite phase, and the saturation magnetization (66.77 emu/g) was lower than that of prefired and conventionally sintered ferrites (88.25 emu/g), the remanent magnetization (0.7367 emu/g) was higher than that of prefired and conventionally sintered ferrites (0.0731 emu/g). Although the microwave sintering process could increase the density of ferrites, the saturation magnetization of ferrites was decreased and the remanent magnetization of ferrites was also increased.     

High-temperature oxidation resistance and magnetic properties of Si-doped Sm2Co17-type magnets at 500 °C

The high-temperature oxidation resistance and magnetic properties of Si-doped Sm₂Co₁₇-type magnets at 500 °C were systematically investigated. The Sm(Co_0.76, Fe_0.1, Cu_0.1, Zr_0.04)₇Si_x (x=0–0.6) magnets were prepared by the conventional powder metallurgical technique. It is found that the addition of silicon in the Sm₂Co₁₇-type magnet can remarkably improve its oxidation resistance. Moreover, a small amount of silicon addition can also increase its high-temperature intrinsic coercivity. A maximum intrinsic coercivity of 6.7 kOe at 500 °C was obtained for the Sm₂Co₁₇-type magnet with Si content x=0.4, whose high-temperature maximum energy product loss was about 2.5 times smaller than pure Sm₂Co₁₇-type magnet after oxidation at 500 °C for 100 h, indicating the enhanced oxidation resistance. Its corresponding Curie temperature and saturation magnetization are about 723.9 °C and 7.4 kG, respectively.     

纳米晶复合Pr2Fe14B/α-Fe永磁材料磁性的研究

采用熔体快淬的方法制备Pr₂Fe₁₄B/α-Fe纳米晶复合永磁材料.使用振动样品磁强计(VSM)测量样品的室温磁性能.实验合金成分为(Pr_xFe_94.3-xB_5.7)_0.99Zr₁(其中x＝8.2，8.6，9.0，9.4，9.8，10.2，10.6，11.0，11.4(原子分数，%)).系统地研究了辊速及合金成分对快淬带磁性能的影响，当Pr原子分数由8. 关键词： 纳米复合永磁材料 熔体快淬 2Fe₁₄B/α-Fe')" href="#">Pr₂Fe₁₄B/α-Fe 磁性     

Research on preparing compact bulk nanocomposite Nd2Fe14B/α-Fe magnetic materials by hot extrusion

In this paper, compact bulk nanocomposite Nd₂Fe₁₄B/α-Fe magnetic materials were prepared by hot extrusion of amorphous and nanocrystalline powders, which were prepared by high-energy ball-milling (HEBM) of the Nd₂Fe₁₄ B-type hard magnetic phase with 20 vol% of α-Fe as soft magnetic phase. The extrusion temperature has important influence on magnetic properties and microstructure of magnetic materials. The results show that the grain size of Nd₂Fe₁₄B and α-Fe phase increases steadily with increasing extrusion temperature. Furthermore, optimal extrusion temperature of 1223 K occurs, at which the highest magnetic properties and relative density can be obtained.     

Preparation, characterization and luminescence properties of porous Si3N4 ceramics with Eu2O3 as sintering additive

Porous Si₃N₄ ceramics with photoluminescence properties were prepared by pressureless sintering using α-Si₃N₄ powder as raw material and Eu₂O₃ as sintering additive. Chemical composition, phase formation, microstructure and photoluminescence properties of porous Si₃N₄ ceramics were studied by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence measurements (PL/PLE). The results show that single Eu₂O₃ additive promotes α→β transformation but not significant densification. A broad band emission center at 570 nm assigned to Eu²⁺ is observed, Eu³⁺ in Eu₂O₃ is (partially) converted to Eu²⁺ by reaction with Si₃N₄, which results in a lower β aspect ratio and β-content compared to the other Ln (Ln=lanthanide) oxide additives.     

Synthesis, structural and magnetic properties of the nanocomposite Fe63B23Nd7Y3Nb3Cr1 magnets

The Fe₆₃B₂₃Nd₇Y₃Nb₃Cr₁ nanocomposite magnets in the form of sheets have been prepared by copper mold casting technique. The phase evolution, crystal structure, microstructural and magnetic properties have been investigated in the as-cast and annealed states. The as-cast sheets show magnetically soft behaviors which become magnetically hard by thermal annealing. The optimal annealed microstructure was composed of nanosize soft magnetic α-Fe (19-29 nm) and hard magnetic Nd₂Fe₁₄B (45-55 nm) grains. The best hard magnetic properties such as intrinsic coercivity, _jH_c of 1119 kA/m, remanence, B_r of 0.44 T, magnetic induction to saturation magnetization ratio, M_r/M_s=0.61 and maximum energy product, (BH)_max of 55 kJ/m³ was obtained after annealing at 680 °C for 15 min. The annealing treatment above 680 °C results in non-ideal phase grains growth, which degrade the magnetic properties.     

电弧炉制备的Sm2Fe17-xCrx化合物的结构与磁性

通过X射线衍射、磁测量等手段对电弧炉制备的不同热处理条件的Sm₂Fe_17-xCr_x（x=1—3）化合物的结构和磁性进行了研究.结果表明1050 ℃下退火5 d的Sm₂Fe_17-xCr_x（x=1—3）化合物具有菱方相的Th₂Zn₁₇型结构,同样温度下退 关键词： 2Fe_17-xCr_x化合物')" href="#">Sm₂Fe_17-xCr_x化合物 磁体积效应 居里温度 磁晶各向异性     

XAFS和XRD研究高能球磨对Fe70Cu30合金结构的影响

利用XRD和XAFS方法研究机械合金化Fe₇₀Cu₃₀二元金属合金随球磨时间的结构变化.XRD结果表明，球磨2 h后，部分金属Fe与Cu生成Fe-Cu合金；球磨20h后，金属Fe与Cu已完全合金化生成Fe-Cu合金，并只在2θ=44°处出现一个宽化的弱衍射峰，认为是在球磨20h后的Fe₇₀Cu₃₀合金中共存着fcc和bcc结构的Fe-Cu合金相.XAFS结果进一步表明，在球磨的初始阶段(2h)，fcc结构的Cu颗粒的晶 关键词： XAFS XRD 70Cu₃₀合金')" href="#">Fe₇₀Cu₃₀合金 机械合金化     

退火诱导亚稳态Fe80Cu20合金固溶体的结构相变

利用扩展x射线吸收精细结构和x射线衍射研究了机械合金化制备的体心立方(bcc)的亚稳态Fe₈₀Cu₂₀合金固溶体的结构随退火温度的变化特点.结果表明，在300—873 K温度范围内，随着退火温度的升高，bcc结构物相的晶格常数近于线性降低，这主要是由于Cu原子从bcc结构Fe₈₀Cu₂₀合金固溶体中逐渐偏析出来，生成面心立方(fcc)结构的Cu物相所致.经603K退火后，Cu原子的平均键长R_Cu—Cu增加了0.003 nm左右，大约有50%的Cu原子从bcc结构的Fe₈₀Cu₂₀合金固溶体中偏析出来.在773 K退火后，bcc结构Fe_８０Cu₂₀合金固溶体近于完全相分离，生成了bcc结构的α-Fe与fcc结构的Cu物相. 关键词： 扩展x射线吸收精细结构 x射线衍射 ８０Cu₂₀合金')" href="#">Fe_８０Cu₂₀合金 机械合金化     

The effect of different temperature annealing on phase relation of LaFe11.5Si1.5 and the magnetocaloric effects of La0.8Ce0.2Fe11.5−xCoxSi1.5 alloys

The phase relation of LaFe_11.5Si_1.5 alloys annealed at different high-temperature from 1223 K (5 h) to 1673 K (0.5 h) has been studied. The powder X-ray diffraction (XRD) patterns show that large amount of 1:13 phase begins to form in the matrix alloy consisting of α-Fe and LaFeSi phases when the annealing temperature is 1423 K. In the temperature range from 1423  to 1523 K, α-Fe and LaFeSi phases rapidly decrease to form 1:13 phase, and LaFeSi phase is rarely observed in the XRD pattern of LaFe_11.5Si_1.5 alloy annealed at 1523 K. With annealing temperature increasing from 1573  to 1673 K, the LaFeSi phase is detected again in the LaFe_11.5Si_1.5 alloy, and there is La₅Si₃ phase when the annealing temperature reaches 1673 K. There almost is no change in the XRD patterns of LaFe_11.5Si_1.5 alloys annealed at 1523 K for 3-5 h. According to this result, the La_0.8Ce_0.2Fe_11.5−xCo_xSi_1.5 (0≤×≤0.7) alloys are annealed at 1523 K (3 h). The analysis of XRD patterns shows that La_0.8Ce_0.2Fe_11.5xCo_xSi_1.5 alloys consist of the NaZn₁₃-type main phase and α-Fe impurity phase. With the increase of Co content from x=0 to 0.7, the Curie temperature T_C increases from 180 to 266 K. Because the increase of Co content can weaken the itinerant electron metamagnetic transition, the order of the magnetic transition at T_C changes from first to second-order between x=0.3 and 0.5. Although the magnetic entropy change decreases from 34.9 to 6.8 J/kg K with increasing Co concentration at a low magnetic field of 0-2 T, the thermal and magnetic hysteresis loss reduces remarkably, which is very important for the magnetic refrigerant near room temperature.     

Effects of different sintering temperature and Nb2O5 content on structural and magnetic properties of Z-type hexaferrites

Nb-doped Z-type hexaferrites (Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁) with composition of Ba₃(Co_0.4Zn_0.6)₂Fe₂₄O₄₁+x Nb₂O₅ (where x=0.0, 0.1, 0.2, 0.4, 0.6, 0.8, 1.2, 1.6 and 2.0 wt%) were prepared by a solid-state reaction method. The effects of different sintering temperature (T_s) and Nb₂O₅ content on the sintering behaviors, phase composing, microstructure, and magnetic properties of the samples were investigated. The results from X-ray diffraction and scanning electron microscopy show that as the amount of Nb₂O₅ additive increases, the major phase changes to Z-phase, Simultaneously, M-phase and a small amount of niobate phase appear. The Nb₂O₅ additive promotes the grain growth as reaction center at lower sintering temperature (1220 °C), but at higher temperature (1260 °C), niobate phase separated out in grain boundaries as secondary phase will restrain abnormal grain growth, so closed pores in grains are not formed. The Nb₂O₅ additive can enhance densification, improve initial permeability of hexaferrites by increasing the grain growth of hexaferrite and the displacement of ions in the sintering process due to the aberration and activation of crystal lattice, which is accompanied by the solubility of Nb⁵⁺ in the hexaferrites. A relative density of 96%, maximum initial permeability (32–33), minimum coercivity (454–455 A/m) and resonance frequency above 400 MHz were obtained for the sample with 0.8 wt% Nb₂O₅ sintered at 1260 °C for 6 h.     

Magnetic properties enhancement of Nd2Fe14B/α-Fe nanocomposites by Ta substitution

Nanostructured Nd_9.5Fe_84−xB_6.5Ta_x (x=0, 0.5, 1, 1.5, and 2) ribbons composed of Nd₂Fe₁₄B and α-Fe phases with a high coercivity and maximum energy product are fabricated by direct melt spinning. The effects of Ta addition on the structures and magnetic properties of melt-spun Nd_9.5Fe_84−xB_6.5Ta_x (x=0, 0.5, 1, 1.5, and 2) ribbons have been investigated. Compared with addition-free ribbons, small addition of Ta is found to reduce the grain sizes of the samples and improve their magnetic properties due to a strong exchange coupling between the Nd₂Fe₁₄B hard phase and α-Fe soft phase. A coercive field of 750 kA/m and a maximum energy product of 158 kJ/m³ in melt-spun Nd_9.5Fe_82.5B_6.5Ta_1.5 ribbons are obtained at room temperature.     

Effect of Cu and Ga additions on the anisotropy of R2Fe14B/α-Fe nanocomposite die-upset magnets (R=Pr,Nd)

Fully dense nanocomposite magnets containing hard R₂Fe₁₄B and soft α-Fe phases were produced from both melt-spun and mechanically milled alloys by hot pressing and subsequent die upsetting. Although R-lean R–Fe–B alloys that do not contain the grain-boundary R-rich phase are known not to be susceptible to texture development by means of die upsetting, we found that small additions of Cu make the texturing possible. The resulting microstructure of oriented platelet grains is similar to that of the R-rich die-upset magnets. Properties of the Cu-containing R₂Fe₁₄B/α-Fe die-upset magnets can be further improved by adding Ga. The anisotropic Pr₁₂Fe₈₀Cu₁Ga₁B₆ magnet made from mechanically milled alloy and containing 17.2 wt% α-Fe had a remanence of 13 kG and a maximum energy product of 23.4 MG Oe. The Pr_11.25Fe_80.75Cu₁Ga₁B₆ magnet made from melt-spun alloy and containing 16.2 wt% α-Fe had a maximum energy product of 19.9 MG Oe. The low coercivity of 3–4 kOe typical for the Cu-containing R₂Fe₁₄B/α-Fe die-upset magnets is due to the relatively coarse α-Fe grains. The latter grains are too large for intergranular exchange interaction, but, nevertheless, they are well coupled with the R₂Fe₁₄B grains by a long-range magnetostatic interaction.     

Mössbauer spectrometric study of ternary Sm2Fe17Nx(x>3)

Among the ternary rare earth-iron-nitrogen compounds, Sm₂Fe₁₇N_x, invented and refined by Asahi Chemical Industry Co., Ltd., shows high magnetic anisotropy, intrinsic coercivity and high saturation magnetization. Powders of Sm₂Fe₁₇, prepared by are melting method, were nitrided in a mixed gas of hydrogen and ammonia to get x=0≈8 samples /1.2/. These samples have crystal structure of Th₂Zn₁₇ and Fe atoms are estimated to locate in 6c, 9d, 18f, and 18h sites /2.3/. The Mossbauer spectrum of Sm₂Fe₁₇N_{3. z} showed several unique magnetic properties. For example, Q.S. due to Fe occupying 18h site shifted to the direction of minus velocity. The result indicates that the nitrogen sites are not only 9e but 3b. CEM spectra of Sm₂Fe₁₇N_x powders showed the doublet due to iron oxide indicating that the surface of Sm₂Fe₁₇N_x powders were oxidised /4/. but even if they were exposed to strongly oxidative atmosphere, the thickness of the oxidised layers increased little, resulting no effect to the magnetic properties and to the Mossbauer magnetic parameters of the bulk.     

新型混合离子-电子导体Sm0.9Ca0.1Al1-xMnxO3-δ的制备及其电性能研究

采用有机凝胶法结合固相烧结技术制备了单相的Sm_0.9Ca_0.1Al_1-xMn_xO_3-δ（SCAM, x=0.1—0.5）新型混合离子-电子导体.通过TG-DTA,XRD和直流四引线法研究了凝胶前驱体的热分解和相转化过程、烧结体的结构、相稳定性、导电性能及其电输运机理.结果表明,凝胶前驱体在900℃焙烧5h可以形成完全晶化的四方钙钛矿相纳米粉体 关键词： 混合离子-电子导体 3')" href="#">SmAlO₃ 有机凝胶法 电导率