电—流变效应演示实验

一、电-流变效应简介早在40年代,美国物理学家Wills.Winslow发现,把某些材料粉末分散在矿物油中制成悬浮液,当施加电场时,其表观粘度及剪切应力随电场的变化而变化。由于在电场作用下该流体呈现非牛顿流体的特点,故称电-流变效应(ER)。电-流变效应的意义在于,可以把这种流体做为一种传动介质,应用于离合器、减     

电流变液中悬浮颗粒的体积与形状的变化

基于偶极近似 ,运用电极化方法 ,定量研究了电流变液中悬浮颗粒在外电场作用下其体积和形状的变化 ,并计算了其体积和形状的相对变化率 .研究结果表明 :悬浮颗粒的体积和形状的相对变化率均与电场强度的平方成正比 ,并与ER本身的性质有关 .一般情况下 ,颗粒的体积和形状的相对变化率分别为 8.4 %和 12 .5 % ,对总体积变化率的贡献为 1.6 8% .这种变化对于ER系统的电涨和电热都作出了贡献 ,仅当将颗粒当作刚性球时 ,其自由能才与电场强度的平方成正比 .     

电流变液中的双折射现象观察

本文研究了电流变液(ER流体)可调节的双折射现象,激光束垂直于电场方向,利用He-Ne激光器对SiO₂、季戊四醇和硅油组成的ER流体进行测量.发现当一对偏振片互相正交,不加电场时,没有光线射出;当施加电场时,就有光线射出,透射光强度随电场增大.对于相同材料的ER流体,低浓度的ER流体双折射现象更加明显,电流变液双折射现象起因于颗粒在电场作用下排列成链状或柱状结构.     

用含苯甲酸甲氧基苯酯的聚硅氧烷组成均相电流变液及其智能阻尼特性的研究

在合成并表征含苯甲酸甲氧基苯酯的侧链液晶聚硅氧烷高分子的基础上,制备了均相电流变(ER)液及其智能阻尼器.测试了ER液及其智能阻尼器在室温下的性能.结果表明,用含苯甲酸甲氧基苯酯的侧链液晶聚硅氧烷能组成在室温下表现出较强ER活性的均相ER液,它在外加电场E=2.2kV/mm,剪切速率为300s-1时,剪切应力达到1550Pa;增加E和振动频率,均相ER液智能阻尼器的阻尼力均增加,阻尼效果提高.     

Rheological Properties of Electrorheological Fluids Beyond and in the Original Transition Zone

We find a nonlinear relationship between the shear stress and shear rate of electrorheological (ER) fluide with aluminosilicate suspension in the original zone corresponding to low shear rates.Beyond the original zone,the ER fluids behave like a Bingham plastic fluid,and their viscosity is nearly constant.     

电流变液的旋光与椭偏光行为

本文研究了电流变液(ER流体)的旋光行为及椭偏光行为.激光束垂直于电场方向,利用HeNe激光器对SiO₂、Si₃N₄和硅油组成的ER流体进行测量.发现电流变液样品存在旋光现象,且对于同一种浓度的ER流体,随着电场强度的增大,旋光角度增大.在同一电场强度下,旋光角度随着浓度的增大而增大.当浓度大于某一值c₀时,旋光角度开始减小,在不同电场强度下,透过电流变液的椭圆偏振光性质不发生改变,且随着电场强度的增大,透射光强度随之增大.电流变液的旋光行为及椭偏光行为起因于在电场作用下ER流体由各向同性的液体转变为各向异性的液体.     

电流变材料构件的频率检测与响应控制

干涉式光纤应变传感器为构件的实时频率检测提供了抗电磁干扰的新型最佳技术手段.本文分析了其在新型的电流变材料构件应用时的若干现象.提出一个位相漂移模型并用以成功处理了有关问题.由此设计的嵌埋型干涉式光纤应变传感器首次使用于受到随机外部激励的电流变结构的振动控制过程.     

基于磁电耦合效应的基本电路元件和非易失性存储器

磁电耦合效应是指磁场控制电极化或者电场控制磁性的物理现象,它们为开发新型电子器件提供了额外的物理状态自由度,具有巨大的应用潜力.磁电耦合系数作为磁电耦合材料的重要参量,体现了材料磁化和电极化的耦合性能,其随外加物理场的变化可以表现出非线性回滞行为,具备作为非易失存储的物理状态特征.本文讨论了基于磁电耦合效应如何建立起电荷-磁通之间的直接关联,继而实现了第四种基本电路元件并构建了完整的电路元件关系图.在此基础上,研究了多铁性异质结中的非线性磁电耦合效应,并利用其独特的电荷-磁通关联特性,开发了基于磁电耦合系数的电写-磁读型非易失性信息存储、逻辑计算与类神经突触记忆等一系列新型信息功能器件.     

磁流变抛光入口区域剪切力场形成机制数值分析

平面光学元件的浸入深度、凸球面光学元件的浸入深度、凸球面光学元件的曲率半径不同会使磁流变抛光入口区域剪切力场发生变化.为了研究磁流变抛光入口区域剪切力场的形成机制,建立磁流变抛光过程中必要的流体模型,对入口区域的几何特征进行分析;通过数值计算平面光学元件不同浸入深度、凸球面光学元件不同浸入深度、凸球面光学元件不同曲率半...     

集成开关型霍尔传感器的特性测量和应用

本对集成开关型霍尔元件的性质进行测量,并就其在转速测量及液位控制等方面的应用进行了大量试验及研究。     

电流变阻尼器的抗冲击性能研究

从理论和试验两个方面研究了所设计的电流变阻尼器在大冲击下的抗冲击性能,分析了电流变液性能与阻尼器结构参数对抗冲击性能的影响。认为采用高性能的电流变液体及改变结构参数,都可以使电流变阻尼器的高速缓冲性能提高。电流变液流速对电流变液的屈服应力影响显著,其值随流速的增加按指数规律减小。从定性、定量两个方面分析了电流变阻尼器作为阻尼器效果不明显的原因为：由电流变效应引起的阻尼力在整个液压阻力所占比例太小,不能通过改变电压来使液压阻力具有很大的调节可控范围。     

平行平板间电流变液非零压力梯度Couette流动的稳定性分析

采用Rajagopal和Wineman所提出本构方程,对电流变液在二维平行平板间非零压力梯度Couette流动的线性稳定性问题进行研究。通过分析和数值计算发现,任何壁面运动都将使流动稳定性增强。在外加电场存在的情况下,电流变液效应也将使流动稳定性增强。     

电流变液中悬浮粒子的布朗运动与其聚集之间关系

在外电场作用下,电流变液中粒子链的聚集与其布朗运动密切相关。为了具体分析这种关系,采用不分离但有相互运动的双球构成的系统去简化粒子链。通过分析双球系统布朗运动特性,得到其无规运动轨迹维数小于2,大量这样的系统在平面中就不可能均匀分布。这说明由于存在布朗运动,在外电场中电流变液中粒子链必然相互聚集,即形成高密度区与低密度区。 关键词：     

KBA X射线显微镜分辨力模型

 综合考虑了几何像差、衍射效应和加工精度等因素对KBA X射线显微镜分辨力的影响,构建了分辨力模型。通过光线追迹模拟得到了不同视场位置的边缘响应函数,以20%～80%的评价标准确定了几何像差分辨力。由构建的空间分辨力模型得到理论分辨力。KBA X射线显微镜整个视场几何像差分辨力、理论分辨力和实测分辨力基本一致。用单层膜KBA 显微镜获得的X射线成像结果,得出中心视场的分辨力约为4 μm,±100 μm视场的分辨力优于5 μm。实验结果表明,几何像差对空间分辨力影响权重相对较大,是影响空间分辨力的决定性因素,其它因素的影响相对较小。     

Theoretical Study on Wavelength Conversion Based on Cross Phase Modulation Using Semiconductor Optical Amplifiers

Performances of wavelength converted signal by cross phase modulation (XPM) using semiconductor optical amplifiers (SOA's) were studied by the use of the multi-section model. Results show that they are related to both the phase arm bias current of the XPM wavelength converter and its operation. When the conversion is under the in-phase operation, the peak extinction ratio (ER) and the chirp frequency of the converted signal increase according to the decrease of the phase arm bias current, but the input signal power dynamic range decreases. When the converter is under the out-of-phase operation, the chirp frequency decreases with the decrease of the phase arm bias current, while the peak ER and the input power dynamic range keep almost the same when the phase arm bias current changes.     

Theoretical analysis of all-optical 2R regeneration in a SOA-based Mach–Zehnder interferometer

All-optical 2R regeneration in a semiconductor optical amplifier-based Mach–Zehnder interferometer is theoretically analyzed. It is shown that the chirp of the regenerated signal is positive, while the input signal has no chirp. The peak extinction ratio (ER) of the regenerated signal is associated with the input wavelength and there exists an input wavelength corresponding to the largest ER of the output signal. The output peak ER is also found influenced by the input power, with lower input power getting higher peak ER.     

极板形貌修饰对电流变液/极板界面滑移抑制实验研究

被外电场极化而固化的电流变液容易在极板处产生剪切滑移而降低其力学性能.使用抛光、激光打坑、覆盖尼龙网和光刻腐蚀四种方法对极板形貌进行了修饰,并对电流变液的压缩力学性能进行了测试.研究表明,光滑极板和光刻腐蚀柱阵列极板易产生界面滑移而压缩强度较低,粗糙坑阵列和覆盖尼龙网可抑制界面滑移而压缩强度高.极板形貌增强极板附近局部电场强度,强化了链末端与极板间的作用,迫使链结构屈服位置远离链末端,从而有效抑制了滑移.研究结果对进一步认识电流变液的屈服强度,提高电流变器件的力学性能有重要参考价值. 关键词： 电流变液 滑移 极板形貌修饰 压缩应力     

Multi-focus design of underwater noise control linings based on finite element analysis

Varied, counter-demanding objectives in designing the underwater noise control linings are addressed using a finite element model based methodology. Four different kinds of designs are proposed to attend to diverse and conflicting requirements concerning echo reduction (ER) and transmission loss (TL) performance of these linings. In this regard a slightly modified hybrid type finite element based on the Pian and Tong (PT) formulation has been used to make the computational efforts less demanding as compared to the original one. The adequacy of this formulation has been shown by comparing its results with the analytical, finite element analysis based, and experimental results. Different unit cell representations for different types of distributions of air cavities on the linings are discussed with respect to their limitations and applicability. Effect of static pressure is studied by using a simplified technique which can be used to simulate deep sea testing environment. Performance variation of different designs is investigated under different water depths to study their applicability in such situations.     

Dynamic stability of a sandwich plate with a constraining layer and electrorheological fluid core

The dynamic stability problems of a sandwich plate with a constraining layer and an electrorheological (ER) fluid core subjected to an axial dynamic force are investigated. The rectangular plate is covered in an ER fluid core and a constraining layer to improve the stability of the system. Effects of the natural frequencies, static buckling loads, and loss factors on the dynamic stability behavior of the sandwich plate are studied in the paper. Rheological property of an ER material, such as viscosity, plasticity, and elasticity may be changed when applying an electric field. The modal damper and the natural frequencies for the sandwich plate are calculated for various electric fields. When an electric field is applied, the damping of the system is more effective. In this study, finite element method and the harmonic balance method are used to calculate the instability regions of the sandwich plate. The ER fluid core is found to have a significant effect on the dynamic stability regions.