Density functional theory study of NO2-sensing mechanisms of pure and Ti-dopedWO3 （002） surfaces

Density functional theory (DFT) calculations are employed to explore the NO₂-sensing mechanisms of pure and Ti-doped WO₃ (002) surfaces. When Ti is doped into the WO₃ surface, two substitution models are considered: substitution of Ti for W_6c and substitution of Ti for W_5c. The results reveal that substitution of Ti for 5-fold W forms a stable doping structure, and doping induces some new electronic states in the band gap, which may lead to changes in the surface properties. Four top adsorption models of NO₂ on pure and Ti-doped WO₃ (002) surfaces are investigated: adsorptions on 5-fold W (Ti), on 6-fold W, on bridging oxygen, and on plane oxygen. The most stable and likely NO₂ adsorption structures are both N-end oriented to the surface bridge oxygen O_1c site. By comparing the adsorption energy and the electronic population, it is found that Ti doping can enhance the adsorption of NO₂, which theoretically proves the experimental observation that Ti doping can greatly increase the WO₃ gas sensor sensitivity to NO₂ gas.     

Ab-initio density functional theory study of a WO3 NH3-sensing mechanism

WO 3 bulk and various surfaces are studied by an ab-initio density functional theory technique.The band structures and electronic density states of WO 3 bulk are investigated.The surface energies of different WO 3 surfaces are compared and then the (002) surface with minimum energy is computed for its NH 3 sensing mechanism which explains the results in the experiments.Three adsorption sites are considered.According to the comparisons of the energy and the charge change between before and after adsorption in the optimal adsorption site O 1c,the NH 3 sensing mechanism is obtained.     

CO和O2分子与TiO2(110)表面负载Pt单原子的相互作用

Pt单原子在低温CO氧化反应中具有很高的催化活性. 利用扫描隧道显微术与密度泛函理论，研究了Pt单原子在还原性TiO₂(110)表面的吸附行为及其与CO和O₂分子的相互作用. 研究发现在80 K低温下，TiO₂表面的氧空位缺陷是Pt单原子的最优吸附位. 将CO和O₂分子分别通入Pt单原子吸附后的TiO₂表面，研究相应的吸附构型. 实验表明在低覆盖度下，单个Pt原子会俘获一个CO分子，CO分子同时与表面次近邻的五配位Ti原子(Ti_5c)成键，进而形成非对称的Pt-CO 复合物构型. 将样品从80 K升温到100 K后，TiO₂表面的CO分子会迁移到Pt-CO处形成Pt-(CO)₂的复合结构. 对于O₂分子，单个Pt原子同样会吸附一个O₂分子，O₂分子也会与最近邻或次近邻的Ti_5c原子成键形成两种Pt-O₂构型. 这些结果在单分子尺度上揭示了CO和O₂与Pt单原子的相互作用，呈现了CO与O₂反应中的初始状态.     

甲醇分子在金红石TiO2(110)和锐钛矿TiO2(001)表面吸附和反应的活性位点

通过高分辨的扫描隧道显微术研究并比较了金红石型TiO₂(110)-(1×1)和锐钛矿型TiO₂(001)-(1×4)两种表面的活性位点． 在金红石型TiO₂(110)-(1×1)表面, 观察到氧空位缺陷是O₂和CO₂分子的活性吸附位点,而五配位的Ti原子是水分子和甲醇分子的光催化反应活性位点．在锐钛矿型TiO₂(001)-(1×4)表面,观察到完全氧化的表面,Ti原子更可能是六配位的,H₂O和O₂分子均不易在这些Ti原子上吸附．经还原后表面出现富Ti的缺陷位点, 这些缺陷位点对H₂O和O₂分子表现出明显的活性． 锐钛矿型TiO₂(001)-(1×4)表面的吸附和反应活性并不具有很高的活性,某种程度上其表现出的活性似乎低于金红石型TiO₂(110)-(1×1)表面．     

H2 分子在Li3N(110)表面吸附的第一性原理研究

采用第一性原理方法研究了H₂分子在Li₃N(110)晶面的表面吸附. 通过研究H₂/Li₃N(110)体系的吸附位置、吸附能和电子结构发现: H₂分子吸附在N桥位要比吸附在其他位置稳定,此时在Li₃N(110)面形成两个-NH基,其吸附能为1.909 eV,属于强化学吸附;H₂与Li₃N(110)面的相互作用主要是H 1s轨道与N 关键词： 第一性原理 3N(110)')" href="#">Li₃N(110) 2')" href="#">H₂ 吸附和解离     

表面桥氧空位对甲醛在二氧化钛表面吸附的影响

Oxygen vacancy (O_v) has significant influence on physical and chemical properties of TiO₂ systems,especially on surface catalytic processes.In this work,we investigate the effects of O v on the adsorption of formaldehyde (HCHO) on TiO₂(110) surfaces through firstprinciples calculations.With the existence of O_v,we find the spatial distribution of surface excess charge can change the relative stability of various adsorption configurations.In this case,the bidentate adsorption at five-coordinated Ti (Ti_5c) can be less stable than the monodentate adsorption.And HCHO adsorbed in O_v becomes the most stable structure.These results are in good agreement with experimental observations,which reconcile the long-standing deviation between the theoretical prediction and experimental results.This work brings insights into how the excess charge affects the molecule adsorption on metal oxide surface.     

Investigation on spectral features of tungsten ions in PbO-Bi2O3-As2O3 glass matrix

Lead bismuth arsenate glasses mixed with different concentrations of WO₃ (ranging from 0 to 6.0 mol%) were synthesized. Differential thermal analysis (DTA), optical absorption, ESR and IR spectral studies have been carried out. The results of DTA have indicated that there is a gradual decrease in the resistance of the glass against devitrification with increase in the concentration of WO₃ upto 4.0 mol%.The optical absorption spectra of these glasses exhibited a relatively broad band peaking at about 880 nm identified due to d_xy→d_x²_−y² transition of W⁵⁺ ions; this band is observed to be more intense in the spectrum of glass containing 4.0 mol% of WO₃. Further, two prominent kinks attributed to ³P₀→¹S₀, ¹D₂ transitions of Bi³⁺ ions have also been located in the absorption spectra. The ESR spectra of these glasses recorded at room temperature exhibited an asymmetric signal at g_⊥∼1.71 and g_ll∼1.61. The intensity of the signal is observed to be maximal for the spectrum of the glass W₄. The quantitative analysis of optical absorption and ESR spectral studies have indicated that there is a maximum reduction of tungsten ions from W⁶⁺ state to W⁵⁺ state in the glass containing 4.0 mol% of WO₃. The IR spectral studies have indicated that there is a increasing degree of disorder in the glass network with increase in the concentration of WO₃ upto 4.0 mol%.     

Effects of CeO2-ZrO2 present in Pd/Al2O3 catalysts on the redox behavior of PdOx and their combustion activity

The ceria-zirconium-modified alumina-supported palladium catalysts are prepared using impregnation method with H₂PdCl₄ as Pd source, hydrazine hydrate as reducing agent. The physicochemical properties of these catalysts are characterized by BET surface area (BET), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction (H₂-TPR) and temperature programmed oxidation (O₂-TPO) techniques, and their catalytic activities for the combustion of methane are examined. The results show that the palladium mainly exist in a highly dispersed PdO species on Ce-Zr-rich grains as well as Al₂O₃-rich grains surfaces, and a stable PdO species due to the strong interaction between PdO and CeO₂-ZrO₂ on the Ce-Zr/Al₂O₃ surfaces. The catalytic activity is strongly related to the redox behavior of PdO species highly dispersed on Ce-Zr-rich grains and Al₂O₃-rich grains surfaces, and the higher the reducibility of the PdO species, the higher the catalytic activity. The presence of Ce-Zr in Pd/Al₂O₃ catalyst would inhibit the site growth of PdO_x particles and decomposition of PdO to Pd⁰, and the reoxidation property of Pd⁰ to PdO_x is significantly improved, which obviously increases thermal stability and catalytic activity of Pd/Ce-Zr/Al₂O₃ catalyst for the methane combustion.     

Adsorption and dissociation of H2 on the Cu2O(1 1 1) surface: A density functional theory study

Interactions of atomic and molecular hydrogen with perfect and deficient Cu₂O(1 1 1) surfaces have been investigated by density functional theory. Different kinds of possible modes of H and H₂ adsorbed on the Cu₂O(1 1 1) surface and possible dissociation pathways were examined. The calculated results indicate that O_SUF, Cu_CUS and O_vacancy sites are the adsorption active centers for H adsorbed on the Cu₂O(1 1 1) surface, and for H₂ adsorption over perfect surface, Cu_CUS site is the most advantageous position with the side-on type of H₂. For H₂ adsorption over deficient surface, two adsorption models of H₂, H₂ adsorbing perpendicularly over O_vacancy site and H₂ lying flatly over singly-coordinate Cu-Cu short bridge, are typical of non-energy-barrier dissociative adsorption leading to one atomic H completely inserted into the crystal lattice and the other bounded to Cu_CUS atom, suggesting that the dissociative adsorption of H₂ is the main dissociation pathway of H₂ on the Cu₂O(1 1 1) surface. Our calculation result is consistent with that of the experimental observation. Therefore, Cu₂O(1 1 1) surface with oxygen vacancy exhibits a strong chemical reactivity towards the dissociation of H₂.     

Roles of γ-Fe2O3 in fly ash for mercury removal: Results of density functional theory study

First-principle calculations based on density function theory (DFT) are used to clarify the roles of γ-Fe₂O₃ in fly ash for removing mercury from coal-fired flue gases. In this study, the structure of key surface of γ-Fe₂O₃ is modeled and spin-polarized periodic boundary conditions with the partial relaxation of atom positions are employed. Binding energies of Hg on γ-Fe₂O₃ (0 0 1) perfect and defective surfaces are calculated for different adsorption sites and the potential adsorption sites are predicted. Additionally, electronic structure is examined to better understand the binding mechanism. It is found that mercury is preferably adsorbed on the bridge site of γ-Fe₂O₃ (0 0 1) perfect surface, with binding energy of −54.3 kJ/mol. The much stronger binding occurs at oxygen vacancy surface with binding energy of −134.6 kJ/mol. The calculations also show that the formation of hybridized orbital between Hg and Fe atom of γ-Fe₂O₃ (0 0 1) is responsible for the relatively strong interaction of mercury with the solid surface, which suggests that the presently described processes are all noncatalytic in nature. However, this is a reflection more of mercury's amalgamation ability.     

Luminescent properties of HTP AgGd1−xW2O8:Eux and AgGd1−x(W1−yMoy)2O8:Eux phosphor for white LED

Intense red phosphors, AgGd_1−xEu_x(W_1−yMo_y)₂O₈ (x=0.0-1.0, y=0.0-1.0), have been synthesized through traditional solid-state reaction and characterized by X-ray diffraction (XRD) and photoluminescence (PL). XRD results reveal that AgGd_1−xEu_xW₂O₈ synthesized at 1000 °C has a tetragonal crystal structure, which is named as high temperature phase (HTP) AgGdW₂O₈. All phosphors compositions with Eu³⁺ show red and green emission on excitation either in the charge-transfer or Eu³⁺ levels. Analysis of the emission spectra with different Eu³⁺ concentrations reveal that the optimum dopant concentration for Eu³⁺ is x=0.6 in the HTP AgGd_1−xEu_xW₂O₈ (x=0.0-1.0). Studies on the AgGd_0.4Eu_0.6(W_1−yMo_y)₂O₈ (y=0.0-1.0) and AgGd_1−xEu_x(W_0.7Mo_0.3)₂O₈ (x=0.0-1.0) show that the emission intensity is maximum for compositions with y=0.3 and x=0.5, respectively, and a decrease in emission intensity is observed for higher y or x values. The Mo⁶⁺ and Eu³⁺ co-doped AgGd(WO₄)₂ phosphors show higher emission intensity in comparison with the singly Eu³⁺-doped AgGd(WO₄)₂ in UV region. The intense emission of the tungstate/molybdate phosphors under 394 and 465 nm excitations, respectively, suggests that these materials are promising candidates as red-emitting phosphors for near-UV/blue GaN-based white LED for white light generation.     

Investigation on densification of Al2O3/B4C ceramic by ab initio calculation and experiment

Compared to experiment, the adsorption energies, bonding properties, and electronic structure of two different Al₂O₃/B₄C bridge sites with seven different Al₂O₃ surfaces are investigated by ab initio periodic density functional theory. The Al₂O₃/B₄C ceramic sintered in Ar is synthesized and measured by XRD and TEM. The calculated results reveal that the densification of O_bridge site of Al₂O₃/B₄C surface is better than that of Al_bridge. The Al₂O₃ (1 1 3)/B₄C with O_bridge is the most favorable and stable. The electronic structure shows that the electron hybridization exists between Al, O atoms and C, B atoms. The results indicate that the calculated results are in good agreement with the experiment.     

Ab initio study of the chemical states of water on Cr2O3(0 0 0 1): From the isolated molecule to saturation coverage

The reactivity of the (0 0 0 1)-Cr–Cr₂O₃ surface towards water was studied by means of periodic DFT + U. Several water coverages were studied, from 1.2H₂O/nm² to 14.1H₂O/nm², corresponding to ¼, 1, 2 and 3 water/Cr at the (0 0 0 1)-Cr₂O₃ surface, respectively. With increasing coverage, water gradually completes the coordination sphere of the surface Cr atoms from 3 (dry surface) to 4 (1.2 and 4.7H₂O/nm²), 5 (9.4H₂O/nm²) and 6 (14.1H₂O/nm²). For all studied coverages, water replaces an O atom from the missing above plane. At coverages 1.2 and 4.7H₂O/nm², the Cr–O_s (surface oxygen) acid–base character and bond directionality govern the water adsorption. The adsorption is molecular at the lowest coverage. At 4.7H₂O/nm², molecular and dissociative states are isoenergetic. The activation energy barrier between the two states being as low as 12 kJ/mol, allowing protons exchanges between the OH groups, as evidenced by ab inito molecular dynamics at room temperature. At coverages of 9.4 and 14.1H₂O/nm², 1D- (respectively, 2D-) water networks are formed. The resulting surface terminations are –Cr(OH)₂ and –Cr(OH)₃– like, respectively. The increased stability of those terminations as compared to the previous ones are due to the stabilization of the adsorbed phase through a H-bond network and to the increase in the Cr coordination number, stabilizing the Cr (t_2g) orbitals in the valence band. An atomistic thermodynamic approach allows us to specify the temperature and water pressure domains of prevalence for each surface termination. It is found that the –Cr(OH)₃-like, –Cr(OH)₂ and anhydrous surfaces may be stabilized depending on (T, P) conditions. Calculated energies of adsorption and OH frequencies are in good agreement with published experimental data and support the full hydroxylation model, where the Cr achieves a 6-fold coordination, at saturation.     

Ni与Co掺杂Fe2O3（0001）表面增强析氧反应活性

Fe based oxides are considered as a promising catalyst for the oxygen evolution reaction (OER) due to their low cost and high stability. Here, based on density functional theory calculations, the electrocatalytic behaviors of pure and metal (Ni, Co) doped Fe-terminated Fe₂O₃(0001) are investigated. The potential-limiting step for OER is determined as the formation of O^* by dehydrogenating surface hydroxyl and it is suggested that the doping enhances the catalytic activity of Fe₂O₃(0001) by reducing the free energy change of rate limiting step on doped Ni or Co atom. Especially, the calculated over-potential of Co-doped Fe₂O₃ (0001) surface is about 0.63 eV on Co site, which is comparable with the theoretical over-potential of 0.56 eV for RuO₂.     

阳离子空位和吸附氧的协同作用对Na0.5Bi0.5TiO3(100)表面磁性影响的第一性原理研究

The combination effect of cation vacancies and O₂ adsorption on ferromagnetism of Na_0.5Bi_0.5TiO₃(100) surface is studied by using density functional theory.An ideal Na_0.5Bi_0.5TiO₃(100) surface is non-magnetic and the cation vacancy could induce the magnetism.By comparing the formation energies for Na,Bi and Ti vacancy,the Na vacancy is more stable than the others.Therefore,we focus on the configuration and electric structure for the system of O₂ molecule adsorption on the Na_0.5Bi_0.5TiO₃(100) surface with a Na vacancy.Among the five physisorption configurations we considered,the most likely adsorption position is Na vacancy.The O₂ adsorption enhances the magnetism of the system.The contribution of spin polarization is mainly from the O 2p orbitals.The characteristics of exchange coupling are also calculated,which show that the ferromagnetic coupling is favorable.Compared with the previous calculation results,our calculations could explain the room-temperature ferromagnetism of Na_0.5Bi_0.5TiO₃ nanocrytalline powders more reasonably,because of taking into account adsorbed oxygen and cation vacancies.Moreover,our results also show that adsorption of O₂ molecule as well as introduction of cation vacancies may be a promising approach to improve multiferroic materials.     

超高温度系数V0.97W0.03 O2多晶薄膜的制备研究

将V₂O₅粉体与WO₃粉体均匀混合并压制成靶，用离子束增强沉积加后退火技术在SiO₂衬底上制备掺钨VO₂多晶薄膜.X射线衍射表明，薄膜取向单一，为VO₂结构的［002］相,晶格参数d比VO₂粉晶增大约0.34%；薄膜从半导体相向金属相转变的相变温度约28；室温(300 K)时的电阻-温度系数(TCR)可大于10%/K，是目前红外热成像薄膜TCR的四倍.W离子的半径大于V离子的半径，W的掺入在薄膜中引入了张应力,使薄膜相变温度降低到室温附近，是IBED V_0.97W_0.03O₂薄膜的室温电阻温度系数提高的原因. 关键词： 二氧化钒薄膜 薄膜掺杂 离子束增强沉积     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

Emission analysis of Pr and Tm: Ca2Gd2W3O14 phosphors

5 mol% of Pr³⁺ and Tm³⁺ ions activated calcium gadolinium tungstate (Ca₂Gd₂W₃O₁₄₎ phosphors were synthesized by traditional solid state reaction method. Crystalline phase structure was identified from the X-ray diffraction (XRD) profiles. From the scanning electron microscopy (SEM) images, we have observed the agglomeration of the particles, and average grain size is around 40-300 nm. Using the energy dispersive X-ray analysis (EDAX) and Fourier transform infrared (FTIR) spectra, identified the elements and functional groups present in the prepared phosphors. The emission spectrum of Pr³⁺: Ca₂Gd₂W₃O₁₄ powder phosphors have shown an intense red emission at 615 nm with the excitation wavelength λ_exci=450 nm and thus these red color emitting powder phosphors are used as one of the components in the preparation of WLEDs. The excitation spectrum of Tm³⁺: Ca₂Gd₂W₃O₁₄ powder phosphor has shown a ligand to metal charge transfer (W-O) band (LMCT) within the WO₄²⁻ group. Emission spectrum of Tm³⁺: Ca₂Gd₂W₃O₁₄ phosphors have shown blue emissions at 453 nm (¹D₂→³F₄).     

SnO2/TiO2 mixed oxide particles synthesized in doped premixed H2/O2/Ar flames

SnO₂/TiO₂ mixed oxides with primary particle size ranging between 5 nm d_p 12 nm were synthesized by doping a H₂/O₂/Ar flame with Sn(CH₃)₄ and Ti(OC₃H₇)₄ co-currently. The effects of “flow coordinate,” concentration and flame configurations were investigated with respect to particle size and morphology of the generated mixed oxides. In situ characterization of the mixed oxides was performed using the particle mass spectrometer (PMS), while XRD, TEM, BET and UV–Vis were performed ex situ. Results obtained showed that primary particle size of mixed oxides can be controlled by varying experimental parameters. The mixed oxides have interesting properties compared to those of the pure oxides of TiO₂ and SnO₂, which were also synthesized in flames earlier. Band gap tuning opportunities are possible using mixed oxides.     

Flowerlike PtCl4/Bi2WO6 composite photocatalyst with enhanced visible-light-induced photocatalytic activity

Flowerlike PtCl₄/Bi₂WO₆ composite photocatalyst was successfully synthesized through a simple two-step method involving a template-free hydrothermal process and the following impregnation treatment. The samples were fully characterized by the study of X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis absorption spectra. The results indicated that the doping of Pt species did not affect the crystal structure and the morphology of Bi₂WO₆ photocatalyst, but it had great influences on the photocatalytic activity of Bi₂WO₆ towards rhodamine-B (RhB) degradation. Besides, the Pt species was found to be present as PtCl₄ in the composite samples, and also an optimal Pt species content on the surface of Bi₂WO₆ photocatalyst was discovered with the highest photocatalytic ability. The improved photocatalytic performance could be ascribed to the enhanced interfacial charge transfer and the inhibited recombination of electron-hole pairs. Meanwhile, a possible mechanism for RhB photocatalytic degradation over PtCl₄/Bi₂WO₆ catalyst was also proposed.