HIAF-BRing的双向涂抹注入模拟

BRing是HIAF工程的主加速器,其设计流强为每个脉冲内的粒子数1×1011个（238U34+）,为了达到此设计流强,注入增益应达到88倍以上。BRing采用了双向涂抹注入方案,其满足BRing的注入增益要求,同时具有注入时间短和累计束分布较均匀而减小了空间电荷效应的特点。双向涂抹注入方案利用水平和垂直两组凸轨磁铁以及倾斜的静电偏转板,在水平相空间和垂直相空间内同时进行涂抹。为了检验双向涂抹注入方案能否达到BRing的设计要求,利用ORBIT程序对双向涂抹注入过程进行了模拟,模拟结果显示,在单次双向涂抹注入113圈的情况下,注入效率为97.7%,注入增益达到110.3倍,满足了BRing流强要求。累积束的分布相对均匀,空间电荷效应引起的工作点漂移约为-0.02,粒子因共振损失风险很小。针对注入束流偏角、切割板角度、工作点偏差和Bump延时等不同注入参数进行了误差分析,结果显示BRing的双向涂抹注入效率对注入参数偏差的容忍度较高。BRing is the main accelerator of High Intensity heavy Ion Accelerator Facility(HIAF) and its design current is 1×1011 particles per pulse (238U34+). To accumulate beams up to the design current, the injection gain has to reach 88. Two planes painting injection scheme is proposed for BRing. This scheme uses a tilted electrostatic septum and 8 bump magnets to paint beams into horizontal and vertical phase space simultaneously. It can inject enough beams into the ring in a short time and paint beams uniformly. The injection process is simulated using ORBIT code and 113 turns is injected into BRing with an injection efficiency of 97.7% which meets the requirement for beam current of BRing. The accumulated beams are distributed uniformly in transverse and hence have a little tune shift of -0.02 which reduces the risk of beam loss due to the resonance. Errors of injection parameters are analysed and the result shows two planes painting injection scheme has a high tolerance for errors of injection parameters.     

kA级脉冲电流注入环的电路建模与分析北大核心CSCD

为满足kA级脉冲电流注入应用需求,设计了一种基于非晶磁芯的电流注入环,其初级线圈采用线缆直接引出的方式,有效解决了传统注入环N型电缆接头耐压不足的问题。之后根据注入环结构建立了其电路模型,并应用粒子群优化算法确定了模型参数值。频域和时域的验证实验表明,仿真结果和实验结果具有较好的一致性,验证了该电路模型的可靠性和正确性。对注入环的实际应用场景进行了仿真分析,结果表明该电流注入环可满足实际应用中kA级脉冲电流注入的需求。     

环形正负电子对撞机注入引出分布参数型冲击磁铁设计

环形正负电子对撞机（CEPC）是一台周长100 km,最高能量为120 GeV的双环对撞机。为了满足不同能量粒子从增强器注入到对撞环,针对W和Z能量模式设计了对撞环离轴注入系统,用于实现束流的累积。为了提高注入效率,兼容不同注入能量,不同束流填充模式,同时尽可能减少注入过程中冲击磁铁对其它束团的扰动,要求对撞环离轴注入冲击磁铁系统是一个上升时间和下降时间小于200 ns,脉冲底宽调节范围为440～2420 ns的梯形波脉冲放电系统。和常见的集中参数型冲击磁铁相比,分布参数型冲击磁铁具有更优越的动态响应特性,适合产生一个前沿更加陡峭、波形更为理想的梯形波脉冲。根据CEPC的束流注入物理需求,完成了一台分布参数型冲击磁铁的物理设计和结构设计,并采用了PSpice和Opera程序进行模拟仿真。设计结果表明：冲击磁铁由26级LC单元结构叠装而成,磁铁总长为1018 mm,磁有效长度为942 mm;在[-20,20] mm磁铁孔径内,磁场强度为0.042 1 T,磁场均匀性优于±0.2%;冲击磁铁系统总上升时间（10%～90%）为193 ns,下降时间（90%～10%）为191 ns。理论分析、...     

基于预群聚的回旋管注入锁相研究

开展了40 kW预群聚注入锁相回旋管的理论与模拟设计。基于全电磁仿真方法完成了预群聚腔的设计,并采用给定场理论对电子束经过预调制腔后的群聚状态进行了计算。采用自洽理论获得了回旋管的自由振荡工作参数,并计算了振荡频率随各种参数变化的规律,由此提出了锁相带宽的要求。采用PIC粒子模拟进行了锁相状态的模拟,得到7 mm漂移距离下锁定增益可达30.5 dB,相应的锁相带宽为20 MHz。如果进一步增长漂移距离或者进一步增大输入功率,锁相带宽还会增大。理论计算和粒子模拟结果表明40 kW级回旋管注入锁相具有良好的可行性。     

托卡马克装置气体注入管线的结构分析与优化

为满足ITER相关设计准则，采用有限元分析方法，以ITER装置单个端口气体注入管线为例，对注入管线开展线弹性应力分析并进行了设计优化。分析结果表明原管线柔性未得到有效限制，在较大形变处增设支撑是必要的。优化后的分析结果显示注入管线在限制柔性的同时管线中的应力值满足设计规范的评判标准，没有出现塑性塌陷、局部失效和棘轮效应，而且支撑等部件的支反力减小33%。验证了优化方案的可行性，最终管线结构的可靠性和安全性得到了明显的改进。     

CFETR 中性束注入系统概念设计

为了满足中国核聚变工程实验堆(CFETR)对等离子体加热和电流驱动的要求,从总体布局、束传输 系统、束源系统三方面进行了中性束注入系统的概念设计。利用参数计算的方法,根据聚变等离子体的要求明确 了中性束注入系统的性能指标和基本布局;利用束传输空间分布程序评估了束传输性能,确定了各功能部件的空 间布局结构;在此基础上,确定了束源系统的性能指标和引出系统布局方式,结合当前研发进展,明确了束源的 基本技术方案。由此完成了中性束注入系统参数指标、束传输关键尺寸、束源性能指标等设计要求,为后续工程 设计奠定了基础。     

空间辐射地面模拟装置(SESRI)同步加速器注入设计和模拟研究

国家"十二五"工程将在哈尔滨工业大学建造一台空间辐射地面模拟装置（SESRI）,该装置能够模拟空间辐照环境,对研究离子辐照材料、生命体等具有重要意义。SESRI主要由双ECR离子源,直线注入器,同步环和3个高能实验终端组成。周长为43.9 m的同步环作为装置的核心部分,能够向3个实验终端输送离子种类多、能量范围广的粒子束。为了保证环内有足够的粒子数,注入系统的设计至关重要,SESRI同步环采用多圈注入方案,并利用ACCSIM程序模拟粒子真实运动情况。结果表明,粒子的注入效率为85.5%,离子数增益可达17.1,可满足设计要求。Space Environment Simulation and Research Infrastructure (SESRI), which is one of the large-scale scientific projects proposed in National Twelfth Five-Year Plan of China, will be constructed in Harbin Institution of Technology. The SESRI project dedicated to space radiation consists of two ECR ion sources, a high intensity ion linac, a synchrotron and 3 research terminals. As the key part of the complex, a 43.9 m synchrotron can provide broadest energy range and variable ion beam for each terminal. To obtain required intensity in the synchrotron, the injection system is significant. A multi-turn injection scheme is adopted in the synchrotron and the injection process is simulated by ACCSIM with multi-particle tracking method. The results show that the injection efficiency and intensity gain factor can reach 85.5% and 17.1 respectively. The multi-turn injection system can meet the design requirement.     

HITFiL同步加速器剥离注入

一台新的治癌专用加速器HITFiL正在设计和建造中,其中一台同步加速器为其主加速器,以高紧凑性、高可靠性和低成本为设计目标。同步加速器的注入系统采用剥离注入方式,剥离注入与单圈注入方式相比能达到较高的注入效率,而其造价明显低于多圈注入加电子冷却的注入方式。治癌采用碳粒子束,从ECR离子源产生的C5+离子经过回旋加速器预加速后在同步加速器注入点处剥离成为C6+注入到环里。详细阐述了该注入系统的设计方案,并对整个注入过程进行了计算机模拟。在模拟过程中,对束流的注入效率、束流损失机制和粒子数增益进行了研究,得到了实空间和相空间的粒子分布和发射度增长趋势,得到了满足要求的束流流强。     

APTR质子同步加速器RFQ直线注入器的优化设计

为实现质子治疗装置的国产化和小型化,基于已完成安装调试的上海先进质子治疗装置(APTR),开展质子治疗注入器系统的升级设计研究,利用PARMTEQM设计软件和快聚束策略,针对APTR同步加速器RFQ直线注入器进行动力学设计模拟。RFQ工作频率为325 MHz,流强18 mA,对从离子源引出的低能质子束流进行匹配俘获、横向聚焦、纵向聚束和预加速,引出能量为3.0 MeV。通过优化预注入器RFQ动力学设计方案和极头参数,有效避免参数共振,减小束流损失,使其整体传输效率达到98.0%,在水平和垂直方向上的发射度增长分别为1.2%和3.3%,出口束流满足下一级腔体的注入需求,开展设计模拟验证和相关冗余度分析,为质子同步加速器的治疗设备和直线注入系统提供参照依据。     

低速度零散的双阳极磁控注入电子枪设计

根据0.14 THz共焦波导回旋行波管对电子枪的要求,完成了双阳极磁控注入电子枪的设计。使用PIC软件对理论设计得到的结构参数进行了模拟优化,最终得到该枪的电子注横纵速度比为0.75,纵向速度零散1.33%。讨论了电极形状、阴极磁场、控制极电压及发射电流对电子注性能的影响,结果表明,设计过程中应对它们进行充分的优化。     

Numerical Modeling of Ion-Optical Systems for Extraction of a Beam of Negative Hydrogen Ions and Its Acceleration and Matching with a Radio-Frequency Quadrupole Accelerator

A source of negative hydrogen ions is constructed at the Institute for High Energy Physics in order to raise the intensity of the U-70 accelerator complex using multiturn charge-exchange injection. The 3D ion-optical IBSimu simulation package was used to model and optimize the system for extraction of an ion beam from plasma, its acceleration to 100 keV, and matching with a radio-frequency quadrupole (RFQ) accelerator. The system of extraction of an ion beam with a current of 50 mA and electron-flow suppression was modeled. The magnetic transport channels with two solenoids and six quadrupole lenses were compared. The end goals of analysis of the matching channel were to obtain the needed Twiss parameters and to minimize the emittance growth at the RFQ input.     

High power acceleration of an HSC type injector for cancer therapy

A hybrid single cavity(HSC) linac, which is formed by combining a radio frequency quadrupole(RFQ)and a drift tube(DT) structure into one interdigital-H(IH) cavity, is fabricated and assembled as a proof of principle injector for cancer therapy synchrotron, based on the culmination of several years of research. The HSC linac adopts a direct plasma injection scheme(DPIS), which can inject a high intensity heavy ion beam produced by a laser ion source(LIS). The input beam current of the HSC is designed to be 20 m A C~(6+) ions. According to numerical simulations, the HSC linac can accelerate a 6-m AC~(6+) beam, which meets the requirement of the needed particle number for cancer therapy(108-9ions/pulse). The HSC injector with the DPIS method makes the existing multiturn injection system and stripping system unnecessary, and can also bring down the size of the beam pipe in existing synchrotron magnets, which could reduce the whole cost of synchrotron. The radio frequency(rf) measurements show excellent rf properties for the resonator, with a measured Q equal to 91% of the simulated value. AC~(6+) ion beam extracted from the LIS was used for the HSC commissioning. In beam testing, we found the measured beam parameters agreed with simulations. More details of the measurements and the results of the high power test are reported in this paper.     

Conceptual design of the system of heavy-ion beam injection into the Booster of the NICA accelerator complex

A project of the system of heavy-ion beam injection into the Booster synchrotron of the NICA accelerator complex developed at the Joint Institute for Nuclear Research (Dubna) is considered. The proposed system provides multivariant injection for accumulating beams with required intensity. The main methods of beam injection into the Booster are described. These are the methods of one-turn, multiturn, and multiple injections. The results of beam dynamics simulations are presented.     

波束方向探测技术的注入式仿真系统验证

这篇文章主要介绍采用功率探测仪方式的注入式仿真系统对波束方向地面探测试验系统进行验证的系统设计和软、硬件控制与实现。通过向注入式仿真系统输入模拟目标星在不同位置发射的信号功率,以及目标星在平台坐标下的角度和位置信息,一方面确定地面探测试验系统技术方案的可行性和检测相关设备的性能,另一方面验证对目标星发射天线主波束方向的探测是否满足精度要求。通过仿真试验证明该注入式仿真系统不仅使用方便、节约成本,而且通过控制相关仪器设备能够准确记录地面探测试验系统对目标星仿真数据的计算信息,进而实现验证。     

全三维55GHz双阳极磁控注入式电子枪数值模拟

根据绝热压缩和角动量守恒理论对55GHz双阳极磁控式注入枪进行了初始参数的设计,并利用自主研发的三维粒子模拟软件CHIPIC对其进行数值模拟,通过改变阴极半径、电子注电流、阴极磁场等参数来分析其对磁控注入式电子枪输出结果的影响。最终通过优化参数和综合因素的考虑,得到了横纵速度比为1.44、最大速度零散为5.8%的高性能电子束,能够很好满足55GHz回旋振荡管对电子束的要求。     

Particle Simulation of a 35-GHz Third-Harmonic Low-Voltage Complex Cavity Gyrotron

A self-consistent particle simulation code has been developed for the research of a 35-GHz third-harmonic Low-voltage complex cavity gyrotron. Aided with microcomputer we use FORTRAN to simulate the process of interaction between electron beam and electromagnetic field. About 7000 macro particles are included at the same time. In the program many useful physical graphs are accessible for the further research of this kind of gyrotron such as the field profile, electrons distribution in various spaces, output power, efficiency and et al. Such simulation results may be helpful to the optimization of devices operation parameters     

Numerical simulation for space charge dominated beam transport

To simulate the intense bunched beam transport, a computer program LEADS-3D has been developed. The particle trajectories are analysed with the Lie algebraic method. The third order approximation of the trajectory solutions is made with space charge forces off, and the second order approximation is made with space charge forces on. The particle distribution in the 3D ellipsoid is uniform or Gaussian. Most of the conventional beam optical elements are incorporated in the code. The optimization procedures are provided to fit the beam lines to satisfy the given optical conditions.     

医用重离子回旋加速器引出系统设计

紧凑型回旋加速器作为重离子医学专用装置同步加速器的注入器,其引出系统设计所用的磁场为TOSCA模型计算磁场。通过单粒子轨道计算确定引出系统的元件类型及基本参数;通过多粒子跟踪确定最终的元件参数和束流参数。为了提高引出效率,改善引出束流品质,在引出位置磁场梯度较大的位置,安放了一块C型磁铁,以改善此处的磁场梯度。同时,为了消除此C型磁铁对主磁场的影响,在此区域安放了一对线圈。计算结果表明引出系统的设计能够保证引出束流的强度和品质符合同步加速器的要求。     

激光场相干叠加光束合成技术

光束拼接激光相干合成中,拼接占空比不高导致合成光束能量集中度不够理想,为了解决这个问题,提出了激光场相干叠加光束合成技术路线,设计了基于半反半透合束镜的多级激光场相干叠加光束合成方案。研究了子光束之间的光强差和波面误差对相干合成的影响,结果表明,激光场相干叠加光束合成中,对参与合成子光束的光强差、相位差的容差均不难满足:仅考虑单一因素时,子束光强相差三倍时合成效率仍可达90%,相位误差小于π/5时,合成效率可达到90.5%。搭建了基于半透半反合束镜的两束激光场相干叠加光束合成实验装置,实验验证了激光场相干叠加光束合成技术的可行性,在闭环情况下得到了稳定的合成光束输出,合成效率可达95%以上。     

强流低发射度光阴极微波电子枪的优化设计

为了实现高增益 FEL,对其关键部件光阴极微波电子枪进行了优化设计 ,还就发射度补偿技术进行了较详细的考虑 ,并用 PARMELA程序进行了粒子动力学的模拟 ,初步给出了为降低初始电子束团横向发射度的优化参数。