单入射波长及纤芯存在光致双折射的长周期光纤光栅的折射率传感分析（英文）

利用全矢量耦合模方程提出并分析了一种基于纤芯存在光致双折射的长周期光纤光栅的环境折射率传感测量方法.以波长为谐振波长的完全偏振光为入射波,通过分析不同环境折射率下输出光的偏振态在邦加球上与参考点间球面距离的变化测量环境折射率.分析表明,在环境折射率1~1.30范围内包层半径为20.75μm的长周期光纤光栅传感器线性特性良好,灵敏度为0.356/RIU,可应用于湿度和气体的折射率测量;该分析方法适用于其他类型的双折射长周期光纤光栅传感器的设计.     

涂有半导体气敏薄膜的长周期光纤光栅气敏传感特性理论分析

首先利用耦合模理论研究了长周期光纤光栅LPFG折射率敏感特性,数值计算了长周期光纤光栅透射谱谐振波长与环境介质折射率的关系。其次分析了半导体氧化物气敏膜光学特性机理,当气体与薄膜接触时,气体会使敏感膜的消光系数、吸收系数和相应的折射率发生变化。基于上述两点,提出可将气敏膜涂于光栅表面,利用气敏膜的折射率随环境气体成分和浓度变化而变化的特性,从而影响LPFG透射谱谐振波长的变化,通过检测波长的变化达到探测气体成分和浓度的目的。由于长周期光纤光栅对环境介质折射率的灵敏度高于光纤,且其传感信号属于波长调制,测量信号不受光强波动及光纤损耗的影响,因此其灵敏度比强度型光纤气体传感器高。     

长周期光纤光栅折射率传感器的结构优化

为了提高长周期光纤光栅对环境介质折射率的传感灵敏度,提出一种长周期光纤光栅的周期和包层半径的结构优化.基于长周期光纤光栅的耦合模理论,分析了长周期光纤光栅的周期和包层半径的大小分别与环境介质折射率传感灵敏度的关系,讨论了长周期光纤光栅的周期和包层半径对折射率传感的影响以及控制光栅周期与包层半径对折射率传感的重要性.为使优化的长周期光纤光栅具有实用性,谐振波长设计在1.55 μm的常规波长范围,经过多次摸拟实验,提出最佳优化参量为：Λ=380 μm,rcl=17 μm,对环境介质折射率从1.26~1.38不同值的实验测试,折射率传感灵敏度达到0.000 12,长周期光纤光栅的结构优化获得理想的预期效果.     

关于镀有LB膜长周期光纤光栅的谐振波长的研究

理论上详细分析了长周期光纤光栅谐振波长随外界环境折射率变化而变化的光谱特性，分析结果可较好地解释镀有LB膜(Langmuir-Blodgett thin-film)的长周期光纤光栅的谐振波长与膜厚之间的关系。分析研究表明．通过减小纤芯直径和改变芯与包层折射率差等方法可调整光纤光栅的谐振波长，使其从一般光纤光栅谐振波长所处的近红外区转到可见光区，以利于光纤光栅配套仪器系统的调试并使系统成本降低，从而为长周期光纤光栅传感技术的发展和应用奠定基础。     

基于长周期光纤光栅的折射率与浓度传感方案的研究

采用简化的3层光纤模型，利用耦合模理论对长周期光纤光栅周围环境折射率、浓度敏感特性进行研究，并用计算机进行模拟及数值计算．得出长周期光纤光栅透射谱谐振波长与环境折射率及浓度的关系．实验证明测量结果与计算机模拟结果基本吻合。     

长周期光纤光栅折射率传感器的结构优化

为了提高长周期光纤光栅对环境介质折射率的传感灵敏度,提出一种长周期光纤光栅的周期和包层半径的结构优化.基于长周期光纤光栅的耦合模理论,分析了长周期光纤光栅的周期和包层半径的大小分别与环境介质折射率传感灵敏度的关系,讨论了长周期光纤光栅的周期和包层半径对折射率传感的影响以及控制光栅周期与包层半径对折射率传感的重要性.为使...     

基于长周期光纤光栅嵌入型Sagnac环光谱的折射率测量

将长周期光纤光栅(LPG)和光纤Sagnac环相结合,实现了折射率和温度的同时测量.首先利用二氧化碳激光器在保偏光纤上制作了长周期光纤光栅(PM-LPG),然后把该PM-LPG和普通单模光纤耦合器组成Sagnac环,作为传感单元.实验选择其某一透射峰作为测试对象,其波长随温度变化,强度随折射率变化,因此可实现两个参量的...     

对弯曲不敏感的长周期光纤光栅传感器

发现了用高频CO₂激光写入的长周期光纤光栅的谐振波长对弯曲灵敏度在圆周的不同方向上呈现周期性,且在两个特定的对称方向上对弯曲不敏感(即弯曲曲率达到1.1m^-1,谐振波长仅漂移-0.018nm).据此提出新型对弯曲不敏感的传感器和可调灵敏度弯曲传感器的设计方案,可望从根本上解决长周期光纤光栅在测量中存在的温度、应变或折射率与弯曲之间的交叉敏感问题.     

基于双峰谐振效应的镀金属长周期光纤光栅液体浓度传感器

利用长周期光纤光栅(LPFG)中的双峰谐振效应,结合表面等离子体共振(SPR)传感器的高灵敏度,提出了一种新型镀金属光纤光栅液体浓度传感器.采用双包层结构模型和耦合模理论,分析r镀金属长周期光纤光栅双峰效应的谐振特性,环境折射率的传感特性以及金属膜厚对双峰LPFG灵敏度的影响.实验上制作了具有双峰效应的镀银膜长周期光纤...     

单端面透射模式长周期光栅的设计和测试

本文设计了一种单端面长周期光栅透射模式折射率传感器。首先,将2×2单模光纤耦合器输入端的一个光纤接头与光源相连接、输出端的两个光纤接头分别与光谱分析仪和长周期光栅的一个光纤接头相连接。然后,在包含长周期光栅的光纤另一个端面溅射反射银膜。最后,以一系列不同折射率的甘油水溶液为待测液体介质研究了直接透射模式与单端面镀银膜模式下长周期光栅的响应光谱的异同。实验结果表明:单端面镀银膜的长周期光栅的响应光谱仍然以透射谱的形式出现。对于同一种液体,单端面镀银膜的长周期光栅与直接透射模式的长周期光栅的响应光谱有着近乎相同的谐振波长值,但它们的光损耗存在一定的差异。在0~80%的甘油溶液中,直接透射模式下的光损耗从-12.92 dB变为-16.28 dB,再逐渐变到-13.22 dB;单端面镀银膜模式下的光损耗从-13.13 dB变为-13.74 dB,再逐渐变到-11.45dB。与直接透射模式相比,单端面镀银膜的长周期光栅的相对光损耗与甘油浓度的线性关系更加良好。本研究设计的长周期光栅测量系统采用单端面探头的方式检测环境介质,因而在测量中操作更加灵活方便,非常适合于远距离、恶劣环境或深层液体环境中的折射率测量。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.