The transverse laser induced thermoelectric voltages in step flow growth （1-x）Pb(Mg1/3Nb2/3)O3-xPbTiO3 thin films

This paper reports that the transverse laser induced thermoelectric voltages (LITV) are observed for the first time in the step flow growth (1-x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT,x = 0.20, 0.33, 0.50) thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate (PMN) and lead titanate (PT), there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength,the largest induced voltage is observed in the 0.50Pb(Mg1/Nb2/3)O3-0.50PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated.     

Laser-induced voltage effects in CaaCoaO9 thin films on tilted LaAlO3（001） substrates grown by chemical solution deposition

Laser-induced voltage effects in c-axis oriented Ca3Co4O9 thin films have been studied with samples fabricated on 10°tilted LaAIO3 （001） substrates by a simple chemical solution deposition method. An open-circuit voltage with a rise time of about 10 ns and full width at half maximum of about 28 ns is detected when the film surface is irradiated by a 308-nm laser pulse with a duration of 25 ns. Besides, opemcircuit voltage signals are also observed when the film surface is irradiated separately by the laser pulses of 532 nm and 1064 nm. The results indicate that Ca3Co4O9 thin films have a great potential application in the wide range photodetctor from the ultraviolet to near infrared regions.     

Laser-induced voltage effects in Ca3Co4O9 thin films on tilted LaAlO3（001） substrates grown by chemical solution deposition

Laser-induced voltage effects in c-axis oriented Ca3Co4O9 thin films have been studied with samples fabricated on 10 tilted LaAlO3(001) substrates by a simple chemical solution deposition method. An open-circuit voltage with a rise time of about 10 ns and full width at half maximum of about 28 ns is detected when the film surface is irradiated by a 308-nm laser pulse with a duration of 25 ns. Besides, open-circuit voltage signals are also observed when the film surface is irradiated separately by the laser pulses of 532 nm and 1064 nm. The results indicate that Ca3Co4O9 thin films have a great potential application in the wide range photodetctor from the ultraviolet to near infrared regions.     

Figure of Merit for Detectors Based on Laser-Induced Thermoelectric Voltages in La1-xCaxMnO3 and YBa2Cu3O7-σ Thin Films

A figure of merit （FOM） Z = Up/τr, where Up is thepeak voltage, and τr is the rise time of the laser-induced thermoelectric voltage （LITV） signal, is defined for photodetector based on the LITV and the influence of the parameters on FOM is analysed based on the time dependence of LITVs in La1-xCaxMnO3 （LCMO） and YBa2Cu3O7-σ （YBCO） thin films grown on vicinal-cut substrates. We find that the FOM increases as the photon penetration depth decreases, and linearly increases with the thermal diffusion constant D. To achieve the highest FOM, the film thickness d has to be controlled to an optimum value. We also find that the FOM is directly proportional to the laser absorption coefficient no, the laser energy density per pulse E, the illuminated length of film 1, sin（2α） [αis the vicinal-cut angle], the Seebeck coefficient anisotropy （ Sab - Sc）, and is inversely proportional to the mass density ρ and the specific heat c0.     

Temperature-Dependent Structure of Epitaxial （Ba,Sr）TiOa Films Grown on SrRuO3-Covered SrTiO3 Substrates

Growth dynamics of epitaxiai （Ba, Sr）TiO3 thin films deposited at different temperatures on SrRuO3/SrTiO3 substrates by pulsed laser deposition is investigated by transmission electron microscopy. The films exhibit a layered structure comprising sublayers with distinctive features in regard to the remaining strain, density of misfit dislocations and/or lattice defects, and growth habit. We correlate these temperature-dependent features with the predominant misfit-strain relaxation mechanisms for each one of the detected growth regimes. The thickness dependence of the film structure is discussed within the framework of the predictions for a kineticaily modified Stranski-Krastanov growth mode.     

Optical Properties of Co-BaTiO3/Mg（100） Nano-Composite Films Grown by Pulsed Laser Deposition Method

Co nanoparticles embedded in a BaTiO3 matrix, namely Co-BaTiO3 nano-composite films are grown on Mg（100） single crystal substrates by the pulsed laser deposition （PLD） method at 650℃. Optical properties of the CoBaTiO3 nano-composite films are examined by absorption spectra （AS） and photoluminescence （PL） spectra. The results indicate that the concentration of Co nano-particles strongly influences the electron transition of the Co BaTiO3 nano-composite films. The PL emission band ranging from 1.9 to 2.2eV is reported. The AS and PL spectra suggest that the band gap is in the range of 3.28-3.7eV.     

Structure,Electrical,and Optical Properties of Nb-doped BaTiO3 Thin Films Grown by Laser Molecular Beam Epitaxy

Structure,electrical,and optical properties of Nb-doped BaTiO3 (Nb:BTO) thin films on MgO substrates grownby laser molecular beam epitaxy with increasing Nb content were investigated.The Nb:BTO thin films with high crystallinity are epitaxially grown on MgO substrates.With more Nb-doped content,the impurity phases are found in Nb:BTO thin films.Hall measurement at room temperature confirms that the charge carriers of the Nb:BTO thin films are n-type.When the Nb-doped content increases,the carrier concentration and carrier mobility increase.Meanwhile the optical transmittance decreases with the increase of the Nb-doping,and the width of the forbidden band in each group is not affected by the presence of Nb in the samples.Raman spectra show that the structural phase transition may occur with the increase of the Nb-doping content,in the meantime more defects and impurities exist in the Nb:BTO thin films.     

Preparation and characterization of in-plane polarized PZT piezoelectric diaphragms

The preparation and characterization of in-plane polarized lead zirconate titanate （PZT） piezoelectric diaphragms for sensors and actuators applications are demonstrated in this letter. The single phase PZT films can be obtained on SiO2-passivated silicon substrates via sol-gel technique, in which PbTiO3 （PT） films are used as seed layers. Al reflective layer is deposited and patterned into concentric interdigitated top electrode by lithographic process, subsequently. The diaphragms are released using orientation-dependent wet etching （ODE） method. The size of the diaphragms is 5 mm in diameter and the outer interdigitated （IDT） electrode diameter （4.25 mm） is fixed at 85~ of the diaphragm diameter. The three-dimensional （3D） profiles results indicate that the measured maximum central deflection at 15 V is approximately 9 μm. Sensing measurements show that the capacitance continually decreases with an increase of applied force, while the case of induced charge exhibits a reverse tendency.     

Structural and physical properties of BiFeO3 thin films epitaxially grown on SrTiO3（001） and polar（111） surfaces

The influence of surface polarity on the structural properties of BiFeO3 （BFO） thin films is investigated. BFO thin films are epitaxially grown on SrTiO3 （STO） （100） and polar （111） surfaces by oxygen plasma-assisted molecular beam epitaxy. It is shown that the crystal structure, surface morphology, and defect states of BFO films grown on STO substrates with nonpolar （001） or polar （111） surfaces perform very differently. BFO/STO （001）is a fully strained tetragonal phase with orientation relationship （001）[100]BFOII（001）[100]STO, while BFO/STO （111） is a rhombohedral phase. BFO/STO （111） has rougher surface morphology and less defect states, which results in reduced leakage current and lower dielectric loss. Moreover, BFO films on both STO （001） and STO （111） are direct band oxides with similar band gaps of 2.65 eV and 2.67 eV, respectively.     

Room-Temperature Ferromagnetism of Co-Doped CeO2 Thin Films on Si（111） substrates

Using Co2O3 as the Co source, doped cerium oxide thin films with the composition of Ce0.97C00.03O2-δ （CCO） are deposited on Si（111） and glass substrates by pulse laser deposition technique. X-ray diffraction reveals that CCO films with （111） preferential orientation are grown on Si, while the fihn on glass is polycrystalline with nanocrystal. X-ray photoelectron spectroscopy shows that the （Jo displaces the （;e atom and exists in high spin state rather than low spin state, which contributes to the room-temperature ferromagnetism confirmed by vibration sample magnetometer. I~ilms on Si and glass are different in ferromagnetism, which is believed to be induced by different film microstructures. Based on these results, the possible ferromagnetism in this insulating film is discussed. Anyway, successful fabrication of CCO films with room-temperature ferromagnetism on Si substrates is of great importance in both technological and theoretical aspects.     

Room-Temperature Ferromagnetism in Zn1-xMnxO Thin Films Deposited by Pulsed Laser Deposition

Zn1-xMnxO （x = O.Olq3.1） thin films with a Curie temperature above 300K are deposited on Al2O3 （0001） substrates by pulsed laser deposition. X-ray diffraction （XRD）, ultraviolet （UV）-visible transmission and Raman spectroscopy are employed to characterize the microstructural properties of these films. Room temperature ferromagnetism is observed by superconducting quantum interference device （SQUID）. The results indicate that Mn doping introduces the incorporation of Mn^2＋ ions into the ZnO host matrix and the insertion of Mn^2＋ ions increases the lattice defects, which is correlated with the ferromagnetism of the obtained films. The doping concentration is also proven to be a crucial factor for obtaining highly ferromagnetic Zn1-xMnxO films.     

Dielectric Enhancement and Maxwell—Wagner Effect in Polycrystalline BaTiO3／Ba0.2Sr0.8TiO3 Multilayered Thin Films

Polycrystalline BaTiO3/Ba0.2Sr0.8TiO3 multilayer thin films were fabricated by pulsed laser deposition onto Pt/Ti/SiO2/Si substrates with various stacking periodicities.The dielectric constant of the films was obviously enhanced with the decrease of the individual layer thickness,while the dielectric loss was kept at a low level comparable to that of the pure Ba0.6Sr0.4TiO3 thin films.The Maxwell-Wagner model is used to explain the experimental data.     

Time-Resolved Femtosecond Degenerate Four-Wave Mixing in LiNbO3：Fe,Mg Crystal

Forward degenerate four-wave mixing （DFWM） processes are investigated with a femtosecond pulsed laser in lithium niobate crystal doubly-doped with magnesium and iron （LiNbO3：Fe, Mg）. The pulse energy dependence reveals a pure third-order nonlinear response, and the third-order nonlinear susceptibility x^（3） in the material is evaluated to be 4.96 × 10^-13 esu. The time-resolved DFWM process shows a response time of x^（3） shorter than 100fs, which is due to the nonresonant electronic nonlinearities. Our results indicate that LiNbO3 crystals have potentials for ultrafast real-time optical processing systems, which require a large and fast x^（3） optical nonlinearity.     

Rectifying characteristics and solar-blind photoresponse in β-Ga_2O_3/ZnO heterojunctions

Heterojunctions composed of β-Ga_2 O_3 and ZnO films are fabricated on sapphire substrates by using the laser molecular beam epitaxy method. The heterojunction possesses excellent rectifying characteristics with an asymmetry ratio over 105. Prominent solar-blind photoresponse effect is also observed in the formed heterojunction. The photodetector exhibits a self-powered behavior with a fast response speed(rise time and decay time are 0.035 s and 0.032 s respectively) at zero bias. The obtained high performance can be related to the built-in field driven photogenerated electron-hole separation.     

Reversal transient laser-induced voltages in La2/3Ca1/3MnO3 films

This paper reports that the transient laser-induced voltages have been observed in La2/3Ca1/3MnO3 thin films on MgO （001） in the absence of an applied current. A peak voltage of - 0.15 V was detected in response to 0.015J pulse of 308 nm laser. It is demonstrated that the signal polarity is reversed when the films are irradiated through the substrate rather than at the air/film interface. Off-diagonal thermoelectricity may support the inversion of the signal when the irradiation direction is reversed.     

Thermoelastic Stress Field Investigation of GaN Material for Laser Lift-off Technique based on Finite Element Method

The transient thermoelastic stress fields of GaN films is analyzed by the finite element method for the laser lift-off （LLO） technique. Stress distributions in GaN films irradiated by pulse laser with different energy densities as functions of time and depth are simulated. The results show that the high thermoelastic stress distributions in GaN films localize within about 1 μm below the GaN/Al2O3 interface using proper laser parameters. It is also found that GaN films can avoid the thermal deformation because the maximum thermoelastic stress 4.28 GPa is much smaller than the yield strength of GaN 15GPa. The effects of laser beam dimension and the thickness of GaN films on stress distribution are also analyzed. The variation range of laser beam dimension as a function of the thickness of GaN films is simulated to keep the GaN films free of thermal deformation. LLO experiments are also carried out. GaN-based light-emitting diodes （LEDs） are separated from sapphire substrates using the parameters obtained from the simulation. Compared with devices before LLO, P-I-V measurements of GaN- based LEDs after LLO show that the electrical and optical characteristics improve greatly, indicating that no stress damage is brought to GaN films using proper parameters obtained by calculation during LLO.     

Thermal Diffusivity of Film/Substrate Structures Characterized by Transient Thermal Grating Method

Transient thermal grating method is used to measure the thermal diffusivity of absorbing films deposited on transparent substrates. According to periodically modulated dielectric constant variations and thermoelastic deformations of the thin films caused by the transient thermal gratings, an improved optical diffraction theory is presented. In the experiment, the probing laser beam reflectively diffracted by the thermal grating is measured by a photomultiplier at different grating fringe spaces. The thermal diffusivity of the film can be evaluated by fitting the theoretical calculations of diffraction signals to the experimental measured data. The validity of the method is tested by measuring the thermal diffusivities of absorbing ZnO films deposited on glass substrates.     

Growth-Parameter Spaces and Optical Properties of Cubic Boron Nitride Films on Si（001）

Cubic boron nitride （c-BN） films were deposited on Si（001） substrates in an ion beam assisted deposition （IBAD） system under various conditions, and the growth parameter spaces and optical properties of c-BN films have been investigated systematically. The results indicate that suitable ion bombardment is necessary for the growth of c-BN films, and a well defined parameter space can be established by using the P/a-parameter. The refractive index of BN films keeps a constant of 1.8 for the c-BN content lower than 50%, while for c-BN films with higher cubic phase the refractive index increases with the c-BN content from 1.8 at χc =50% to 2.1 at χc = 90%. Furthermore, the relationship between n and p for BN films can be described by the Anderson-Schreiber equation, and the overlap field parameter γ is determined to be 2.05.     

Photoluminescence and transmission spectra of nanocrystalline GaAs（1-x）Sbx embedded in silica films

The composite films of the nanocrystMline GaAs（1-x）Sbx-SiO2 have been successfully deposited on glass and GaSb substrates by radio frequency magnetron co-sputtering. The 10K photoluminescence （PL） properties of the nanocrystalline GaAs（1-x）Sbx indicated that the PL peaks of the GaAs（1-x）Sbx nanocrystals follow the quantum confinement model very closely. Optical transmittance spectra showed that there is a large blue shift of optical absorption edge in nanocrystMline GaAs（1-x）Sbx-SiO2 composite films, as compared with that of the corresponding bulk semiconductor, which is due to the quantum confinement effect.     

Effect of Temperature on Structural and Magnetic Properties of Laser Ablated Iron Oxide Deposited on Si（100）

We fabricate Fe3O4 thin films on Si（100） substrates at different temperatures using pulsed laser deposition, and study the effect of annealing and deposition temperature on the structural and magnetic properties of Fe3O4 thin films. Subsequently, the films are characterized by x-ray diffraction （XRD）, scanning electron microscopy （SEM） and vibrating sample magnetometery （VSM）. The XRD results of these films confirm the presence of the Fe3O4 phase and show room-temperature ferromagnetism, as observed with VSM. We demonstrate the optimized deposition and annealing conditions for an enhanced magnetization of 854 emu/cm3 that is very high when compared to the bulk sample.