YBCO带材交流损耗电测法实验研究

介绍了交流损耗测量理论,搭建了高温超导带材的电测法测量平台,并分别测量不同频率下AMSC和Super Power两家公司生产的YBCO带材的交流损耗。将测试结果进行了归一化处理,并与计算结果和Norris模型进行比较,从两种带材材料层面分析了测量结果与计算结果存在微小差别的原因。实验结果表明测量结果与计算结果基本一致,并且和Norris模型吻合较好,说明该测量系统可以很好地测量不同频率下YBCO带材的交流损耗。     

Bi系高温超导带材交流传输损耗的研究和分析

本文研究了Bi-2223高温超导带材的交流传输损耗和频率及运行电流的关系, 调查了热循环过程对交流传输损耗的影响. 实验中, 使用了Lock-in 放大器, 利用四引线法来测量带材交流传输损耗. 实验在温度为77K频率从45Hz到135Hz下进行. 在调查损耗和频率及运行电流的关系时, 发现在运行电流幅值小于临界电流时, 每周传输损耗和频率无关, 说明这时的损耗主要来源于磁滞损耗, 实验结果和Norris椭圆模型的计算结果很接近. 在研究交流传输损耗和热循环的关系时, 发现随着冷热循环次数的增加, 交流损耗也在增加. 这种损耗的增加来源于冷热循环过程中产生的应力, 这种应力的释放减弱了晶粒间的Josephson连接, 使临界电流下降, 从而造成了交流传输损耗的增加.     

铜骨架高温超导复合缆线的交流损耗计算

高温超导复合缆线的运行温度直接决定其载流性能,超导带材交流损耗计算的准确性对缆线的温升计算至关重要。面向具有铜骨架和双层高温超导带材结构的高温超导复合缆线,通过改进利兹线(Litz-wire)涡流损耗计算模型,将导电层作为利兹线结构中由多股线按一定节距扭转的束级结构的并联,分别计算了49.9 Hz和60 Hz下复合缆线的集肤效应损耗和邻近效应损耗。通过分析高温超导带材的平行磁场分量和垂直磁场分量,计算了复合缆线的磁滞损耗。最后,基于超导样缆交流损耗补偿测量系统,对0.2 m、110 kV/1.5 kA铜骨架高温超导复合缆线的交流损耗进行了测量,得到工频下1 200 A载流时的交流损耗为1.21 W。研究发现,在不同频率下,铜骨架高温超导复合缆线的交流损耗随传输电流的增大而增大。通过对比仿真和实验结果,验证了铜骨架高温超导复合缆线交流损耗计算结果的准确性。     

高温超导电流引线电磁特性及交流损耗研究

在无限长堆叠带材模型的基础上对高温超导电流引线的交流损耗建立了新的计算模型,即正十二边形骨架计算模型.由于正十二边形对称性,通过建立合适的坐标系,对坐标进行旋转即可求出每堆带材处的磁场.使用matlab编程计算并得出一系列电流下的交流损耗值,通过将所得数据绘成图形,比较了不同电流下穿透深度及交流损耗的大小.然后搭建实验平台,测量了不同频率下电流引线的交流损耗,并将理论与实验对比,得到较好的一致性.     

高温超导YBCO线圈交流损耗的频率特性

YBCO线圈的交流损耗直接关系到YBCO设备的运行成本及稳定性。实现对YBCO线圈交流损耗的快速、准确测量,对于开展YBCO涂层导体的应用研究具有重要的意义。文中采用电测量法,在77K、零场和不同频率条件下,对YBCO线圈通以不同运行电流时产生的交流传输损耗进行测量。构建了YBCO线圈交流损耗的数值计算模型,对YBCO线圈交流损耗进行理论研究,最后将实验数据与理论计算结果进行比较,两者结果基本一致。可以发现,YBCO线圈在频率低于75Hz时,交流传输损耗随频率的增大而减小,当频率从75Hz增加到195Hz时,交流传输损耗随频率的增大而增加。     

基于改进电测法的Bi-2223/Ag高温超导带的交流损耗研究

研究了B i-2223/Ag高温超导带材的交流传输损耗与频率及运行电流的关系。采用锁相放大器激励,内参考方式,首先对纯阻性相位进行定标的改良电测法,对带材的交流传输损耗进行测量。实验在温度77K,频率45-200Hz的范围内进行。实验结果显示:当运行电流幅值小于临界电流时,传输损耗与电流的关系式(P-In)中,指数n介于2-3之间,说明这时的损耗除来源于磁滞损耗外,涡流损耗的作用也不可忽略。鉴于电测法测得的交流损耗与Norris模型的理论计算值差别较大,分析了这种差别产生的原因,并与另一种B i系高温超导带的交流损耗情况进行了对比;此外还对实验误差的大小进行了理论估测。     

直流偏置下YBCO单层导体的交流损耗特性研究

在高压直流输电系统中,高温超导直流电缆具有高功率密度特点被广泛使用。然而,电网中的直流以及开关器件和环境产生的交流纹波,都造成交流损耗。由第二代(2G)带材组成的五边形单层导体在交流和直流作用下,进行了交流损耗特性研究。该次实验从电压引线高度,接触位置和频率等不同角度测量分析了五边形单层导体的交流损耗。结果表明,尽管电压引线的接触位置不同,由于五边形单层导体的对称结构,每根带材的交流损耗几乎相同;当总电流大于临界电流时交流损耗取决于频率。此外,对五边形单层导体进行了仿真计算,与实验结果做了比较分析。结果表明,交流损耗实验测试结果与模型仿真结果基本吻合。     

高温超导YBCO带材的交流损耗的FEM仿真分析

对高温超导带材YBCO的交流损耗进行了仿真分析。运用有限元FEM方法,基于Maxwell方程组的数值建模,引入了基于实验数据的power-law对交流损耗进行计算。首先对自场下的交流损耗值进行了仿真计算并分析了带材的电流密度与磁场分布情况,并通过与实验测量数据做比较验证仿真方法的有效性。其次分别对不同幅值下的平行场与垂直场下的交流损耗进行了计算,将自场、平行场以及垂直场下的电流密度与磁场强度的分布以及交流损耗值进行了对比分析。     

圆筒形高温超导体的交流损耗研究

针对高温超导电缆、限流器等电力设备中常应用的圆筒形高温超导体进行交流损耗特性研究.本文对单根Bi-2223带材以及由十根该带材制作的十边形高温超导体样品的交流损耗特性进行实验测量,并应用有限元软件研究单根带材、理想圆筒形高温超导体和十边形高温超导体的二维有限元计算模型,基于有限元的数值模型对交流损耗进行仿真计算,最后将数值计算结果、实验测量结果以及基于mono-block模型的理论计算值进行比较并详细的分析讨论,结果表明,圆筒形高温超导体的交流损耗最少.     

外场下机械振动对高温超导带材交流损耗的影响

高温超导带材在磁场中传输交变电流时,将受到电磁力的作用而产生机械振动,振动对带材的交流损耗将产生影响.本文讨论了振动情况下交流损耗的测量方法,在平行于带面的直流磁场下,测量了Bi-2223/Ag高温超导带材在不同振动情况下的交流损耗.结果显示:当传输电流频率偏离样品的共振频率时,振动对带材的交流损耗影响不大;只有当电流频率在共振频率附近时,样品产生剧烈振动,交流损耗才有明显的增加;另外,带材振动时的交流损耗随频率变化曲线的斜率比不振动时略有增加.     

AC losses in multifilamentary HTS-composite tapes based on BiPbSrCaCuO

Some results of AC loss measurements are presented for 19, 61, 127-filamentary Bi-2223/Ag tapes prepared by the ‘powder-in-tube' method. All measurements have been made at T=77 K under sinusoidal transport current with frequency in the range of 30–600 Hz and the current amplitude up to 30 A. The measurements have been carried out both in self field conditions and at the external magnetic field applied to the tape at the different angles. The dependencies of the AC losses on current amplitude and frequency have been obtained. It is found that for all tapes the current amplitude dependencies of the AC losses show good agreement with the Norris prediction for an elliptical or strip geometry. The AC loss dependencies on frequency were linear. The measurements of AC losses in external magnetic field show that the change of AC losses is only through the change of the critical current. So the transport AC losses in the tapes are the ‘saturation losses' that is they are different from classic hysteresis losses.     

The frequency dependence of AC transport losses in stacked Bi—2223／Ag superconducting tapes

AC transport losses in a single superconducting tape, double-and triple-stacked Bi-2223/Ag superconducting tapes were measured by use of electrical method. The measurements were carried out at 77K with the frequency of AC transport currents ranging from 50 to 100Hz. The dependence of AC losses on frequency and the number of tapes in the stack were presented and analysed.     

高温超导带材YBCO涂层导体的失超传播特性研究

在液氮(77K)环境下对YBCO涂层导体的交、直流失超传播特性进行了研究。测量了交、直流情况下的失超传播速度以及最小失超能量;分析了超导带材的失超传播速度与传输电流的关系;推导了一维模型下的失超传播速度计算公式。结果表明,当带材的传输电流交流(有效值)与直流相同时,交、直流失超传播速度基本一致,交流的最小失超能略小,且随着传输电流的增大最小失超能间的差距加大。     

具有不同临界电流的Bi2223/Ag多芯超导带材的自场损耗和交流电流电压特性

对具有不同临界电流的Ｂｉ２２２３／Ａｇ多芯超导材的交流电流电压特性进行了测量和评价,当传输电流的有效值Ｉｎｎｓ小于临界电流Ｉｃ时,交流电压的大小与传输电流的频率成正比;但Ｉｎｎｓ接近临界电流时,不同频率所对应的交流电压的大小之间的差别减小了,所有的曲线都汇聚成一条曲线,传输电流的频率分别为４０Ｈｚ,６０Ｈｚ,８０Ｈｚ,２００Ｈｚ及３００Ｈｚ时,我们测量了交变传输电流在Ｂｉ２２２３／Ａｇ带材中产生的自场损耗。结果表明当传输电流的频率较低时,实验结果与基于Ｂｅａｎ模型的Ｎｏｒｒｉｓ方程预期的结果一致;另外,实验结果表明存在一个电流Ｉ′,它的值小于任何一个样品的临界电流,本实验中Ｉ′的值是１０安培,在传输相同大小的电流Ｉｎｎ且Ｉｎｎｓ〈Ｉ′时,Ｂｏｉ２２２３／Ａｇ带材的交流损耗与它的临界电流成正比;但当Ｉｎｎｓ〉Ｉ′     

A simple electromagnetic method of cyclic loss measurement for superconducting wires in a combined alternating transverse magnetic field and transport current

We measured cyclic losses in a superconducting wire, carrying alternating transport current, simultaneously exposed to an alternating transverse magnetic field. Samples of Bi-2223 Ag-sheathed tapes have configuration of a double-layer non-inductive coil, which itself is a pickup coil to measure the AC losses. Potential taps were attached to both terminals of the sample coil. The external field was applied along the axis of the sample coil. In this procedure, we can estimate an averaged Poynting's vector on a cylindrical surface between the two layers by means of signals from a pair of the potential taps and from pickup coils for the external magnetic field and the transport current. We can also measure a magnetization and an extended transport-current components of AC losses in addition to a total cyclic loss for a combined alternating external field and transport current. Obtained results are compared with numerical predictions of the critical state model taking into account the magnetic field dependence of critical current density.     

Finite element analysis of AC loss in non-twisted Bi-2223 tape carrying AC transport current and/or exposed to DC or AC external magnetic field

AC losses in Bi-2223 superconducting tapes carrying AC transport current and/or exposed to DC or AC magnetic field are calculated with a numerical model based on the finite element method. Superconducting property is given by the E–J characteristic represented by a power law using equivalent conductivity. First, transport loss and magnetization loss are calculated numerically and compared with measured values. The calculated losses almost agree with the measured losses. Frequency dependencies of calculated and measured transport losses are compared with each other. Next, the influence of DC external magnetic field on the transport loss is studied. DC external magnetic field reduces n that is an exponent in the power law connecting resistivity and current density. The numerically calculated transport loss increases with increasing DC magnetic field. Finally, the total loss of superconducting tape carrying AC transport current in AC magnetic field is calculated. In the perpendicular magnetic field, the calculated total loss is lager than the sum of the transport loss and the magnetization loss, while they almost agree with each other in the parallel magnetic field.