The research of phase-locking of more discharge tubes for two-dimensional axisymmetric-fold combination resonator CO2 laser

A method of reflection-injection phase-locking used on two-dimensional axisymmetric-fold combination resonator (ASFC) CO₂ laser has been proposed. The structure characteristics and the method of phase-locking have been introduced. The expression of output light intensity distribution has been deduced by matrix theory and Collins Formula and the output light intensity distribution has been numerically calculated and simulated. Comparing the output light intensity distribution in the case of phase-locking with that of non-phase-locking. The result shows that this method of phase-locking greatly improve the characteristics of output beam.     

光泵气体THz激光器用CO2泵浦源腔内光场模式

CO2泵浦源是光泵气体太赫兹激光器的核心器件之一,其性能直接关系到太赫兹激光器的工作稳定性。CO2泵浦源一般由闪耀光栅作为全反射尾镜,构成特殊的光栅腔实现波长的选支输出。采用传输矩阵的特征向量法对光栅谐振腔的腔内光场模式进行了理论分析与数值模拟,计算了光栅腔的一系列本征模式及相应的衍射损耗。结果表明光栅腔的腔内模式特性等效于一个平凹腔,而对于大菲涅尔数的光栅腔, Littrow波长的附近支线也可能具有衍射损耗较低的低阶模,可能优先于Littrow波长的高阶模起振,导致光栅腔的波长选择性降低。     

高损伤阈值矩形石英闪耀光栅的设计分析

 采用模态法分析了矩形亚波长石英闪耀光栅的设计原理,给出了1.06 μm工作波长的矩形亚波长石英闪耀光栅的设计示例。研究表明,要设计性能优良的-1级透射闪耀光栅,应使0/1阶传输模的累积相位差为π的奇数倍。设计的透射闪耀光栅能够使TM偏振光和TE偏振光获得近100%的-1级衍射效率,且具有较大的加工容差,较宽的入射波长和入射角变化适应范围。     

小角度衍射噪声光栅滤波方法研究

针对因衍射等原因引起的小角度差光噪声信号,探讨了利用闪耀光栅的2级闪耀,实现角度差放大,提高空间低通滤波器适应性的滤波新方法。理论分析和模拟仿真表明,对于小于5°的角度差,可实现3倍以上放大。放大所需闪耀光栅的频率与入射单色波长成反比,波长越长,所需光栅频率越低。与正的斜入射角相比,负斜入射角度差的放大倍数更大。当负斜入射角超过一定值时,会因为全反射角的限制而导致斜入射2级闪耀不存在,只保留了有效信号的2级闪耀,滤波效果更好。     

基于闪耀光纤光栅的折射率传感技术实验研究

提出了一种基于闪耀光纤光栅传感技术的折射率测量新方法,即采用SLED作为光源,通过检测闪耀光纤光栅透射谱强度实现折射率的测量.实验证明,当环境折射率在1.372 3~1.453 2之间变化时,闪耀光纤光栅透射功率从0.611~0.472 mW线性下降,其灵敏度达到1.718 μW/（0.001折射率变化）.该检测方法具有结构简单、无需波长检测、灵敏度高、易于工程化等优点.     

Fabrication of Silicon-Blazed Gratings for Couplers

To our knowledge, no blazed grating has been fabricated in silicon (Si) at a pitch of less than half a micron. In this article, we report the fabrication of Si-blazed gratings at the period of 400 nm, using electron beam lithography and ion beam etching techniques. The blazed grating is extremely useful as a grating coupler in integrated optics, operating at the telecommunication wavelength of 1.3 mum, because very high output efficiency of the grating coupler is expected. This will allow coupling to thin film devices in silicon, previously not regarded as promising because coupling to them was very inefficient.     

共振域矩形介质光栅的逆向设计

采用模态法研究了共振域光栅分束器及闪耀光栅等光学器件的设计原理及逆向设计方法,给出了-1级非偏振闪耀光栅的典型设计示例。研究表明,自准直角入射时,光束在光栅内传输将激发产生离散模,通过调节离散模透过光栅传输时的累积相位差,可对衍射光进行调控,实现偏振(非偏振)分束、偏振(非偏振)闪耀等功能。采用严格耦合波法对基于模态法逆向设计的-1级非偏振石英闪耀光栅的几何参数进行验证,计算结果显示两者非常吻合,证明了该方法的正确性。     

Fabrication of Silicon-Blazed Gratings for Couplers

To our knowledge, no blazed grating has been fabricated in silicon (Si) at a pitch of less than half a micron. In this article, we report the fabrication of Si-blazed gratings at the period of 400 nm, using electron beam lithography and ion beam etching techniques. The blazed grating is extremely useful as a grating coupler in integrated optics, operating at the telecommunication wavelength of 1.3 mum, because very high output efficiency of the grating coupler is expected. This will allow coupling to thin film devices in silicon, previously not regarded as promising because coupling to them was very inefficient.     

适用于宽带光的闪耀光栅衍射强度分布规律研究

变栅距光栅线位移传感器是一种新型波长编码位移传感器,为进一步提高传感器波长解调的精度和减小光源的体积,提出适用于全工作波段的恒定闪耀角变栅距光栅结构。首先采用经典光学的方法推导出变栅距闪耀光栅衍射强度分布公式,从理论上证明该光栅结构可实现在全工作波段提高变栅距光栅线位移传感器衍射光强。此外,制作出变栅距闪耀光栅样件证实了工艺可行性。在相同的条件下,对一组参数相同的闪耀光栅和矩形槽形光栅进行了衍射光强比对实验,得到变栅距闪耀光栅的衍射光强约为矩形变栅距光栅的衍射光强的1.7倍,并与按此衍射光强分布公式计算的结果一致。     

闪耀光栅的二元近似结构

摘要利用闪耀光栅的特点可制作高效的波导耦合器。采用时域有限差分法(FDTD)方法，模拟计算了二元闪耀光栅的一阶衍射效率和衍射角随光栅不同结构参数而变化的相关特征，所得结果对实际二元闪耀光栅的制备有重要参考价值。     

基于数字闪耀光栅的位相全息图光电再现优化

针对利用液晶空间光调制器（LC-SLM）进行全息图光电再现过程中,再现像面存在多级衍射像造成单一像能量利用率低的问题,提出了一种在位相全息图中加载数字闪耀光栅的方法,以提高全息图光电再现中单一衍射像的衍射效率.分析了闪耀光栅作为衍射光学元件的特性及其对光波进行位相调制的原理,并阐述了在LC-SLM中加载数字闪耀光栅对位相全息图光电再现时像面能量分布的影响.搭建了基于LC-SLM的位相全息图光电再现实验系统.理论分析表明：在其他条件不变的情况下,加载竖直（或水平）槽向周期为2 pixels的数字闪耀光栅可使 关键词： 全息光电再现 位相全息图 数字闪耀光栅 液晶空间光调制器     

Record high extreme-ultraviolet efficiency at near-normal incidence from a multilayer-coated polymer-overcoated blazed ion-etched holographic grating

We have measured the extreme-ultraviolet (EUV) efficiency of a polymer-overcoated blazed ion-etched holographic test grating. The grating had a magnetron-sputtered Mo2C/Si multilayer coating matched to the grating blaze angle of 2.78 degrees. At an angle of incidence of 5.6 degrees and a wavelength of 15.79 nm, the measured efficiency peaks in the second outside order at 29.9%. The derived groove efficiency is 53.0%. To the best of our knowledge these are the highest values obtained yet at EUV wavelengths from a holographic ion-etched blazed grating.     

Blazed binary subwavelength gratings with efficiencies larger than those of conventional échelette gratings

We introduce a new structural cutoff beyond which subwavelength gratings cease to behave as homogeneous media and discuss its effects on the proper selection of the sampling periods of subwavelength diffractive elements. According to this analysis, a 3lambda-period blazed binary grating composed of square pillars is designed for He-Ne operation and is fabricated by etching of a TiO>(2) layer deposited upon a glass substrate. Its first-order measured diffraction efficiency is 12% larger than the theoretical efficiency of an ideal blazed échelette grating in glass with the same period.     

Experimental proof on two-cone axisymmetric-folded combination CO2 laser

The experimental proof of the light output on the two-cone axisymmetric-folded combination (ASFC) CO₂ laser has been performed. The output power from the centre discharge tube is 26.7 W, and that of one couple of folded discharge tubes is 40.5 W. Seventeen beams can be obtained from the device, which are from the folded cavities with axes placed in the inner and outer cones, respectively. Therefore, the ASFC CO₂ laser with more discharge tubes can be fabricated and much higher output power can be obtained.     

等腰闪耀光栅及其在非对称双光栅位移测量中的应用研究

本文简述了非对称双光栅位移测量的原理和特点,针对其中存在的一些问题,设计了一种新型透射式位相光栅———等腰闪耀光栅。文中导出了等腰闪耀光栅在垂直入射时的光栅方程和衍射光强分布公式,并通过计算机仿真,得到了衍射光强的分布图。最后探讨了等腰闪耀光栅在非对称双光栅位移测量中的应用     

偏晶向(111)硅片闪耀光栅的制作

硅光栅的制作可以利用湿法腐蚀体硅工艺.湿法腐蚀利用硅的各向异性,由硅的晶面形成光栅工作凹槽,利用湿法工艺可以制作在不同光谱波段内工作的闪耀光栅.设计了一种利用偏晶向(111)硅片制作闪耀光栅的方法,使用这种方法可以批量制作闪耀角度较小的光栅.利用扫描电子显微镜(SEM)进行了光栅表面形貌测试,试验结果表明,制作的硅光栅样片具有良好光学特性的反射表面和光栅槽形.硅闪耀光栅可以被用来制作微型光谱仪、滤光器等微型仪器或器件.     

The influence of misalignment of an axisymmetrical folded-combined CO2 laser on output power

The influences of misalignments of an axisymmetrical folded-combined (ASFC) CO₂ laser on the output power are studied in detail. The new cavity axes are established by using the misaligned matrixes corresponding to the misalignments of the output mirror and the discharge tube, and the diffraction losses of the cavity and the output powers are calculated. It is shown that the influences of the misalignments on the output power are significant when the misalignment angle of the output mirror exceeds 20 s. These calculated values afford references for the design of ASFC CO₂ lasers.     

High-efficiency subwavelength diffractive element patterned in a high-refractive-index material for 633 nm

We propose the use of high-index materials for the fabrication of subwavelength diffractive components operating in the visible domain. This approach yields a reduction of fabrication constraints and an improvement of theoretical performance. A blazed grating with subwavelength binary features and with a period of 5.75 wavelengths is designed and fabricated in a TiO(2) layer coated upon a glass substrate. The first-order diffraction efficiency measured with a He-Ne laser beam is 83%, which is slightly larger than that achieved theoretically by the best standard (continuous profile) blazed grating fabricated in glass with the same period.     

Untersuchungen an derL II,III-Röntgenemissionsbande von Aluminium mit einem neuen Konkavgitterspektrographen

A concave grating spectrograph (blazed grating, r=2000mm, blaze angle 1°31′, 600 lines/mm; angle of incidence 85°) designed for the wavelength region λ=40... 600 A is described. The X-ray tube is mounted inside the spectrograph and works at a pressure of about 10^?8 Torr. The detector is an open photomultiplier with a tungsten photocathode. The sensitivity of the apparatus allows even at low target input (3 kV; 0.5...3.5 mA) the observation of the formation of a carbon layer on the target and the decomposition of compounds by electron bombardement during the course of the measurement. TheL _{II, III}-emission bands of metallic Aluminium and Aluminiumoxide are investigated. The spectra agree on the whole with those published previously, but they show more pronounced structural features. The reasons for the differences are discussed. It appears that most of the emission bands obtained with photographic-photometric registration will have to be remeasured.     

亚波长闪耀光栅矢量衍射效率计算

将矢量衍射数值算法—严格耦合波分析用于精确计算亚波长闪耀光栅的衍射效率,并分析其衍射特性。建立了闪耀光栅的电磁介质模型,并将楔形不规则结构简化为多层矩形光栅结构,通过电磁场的介质分布建立严格耦合波方程。根据边界条件求解出各层的电磁场分布,再通过增透矩阵方法将各层电磁场依次迭代,求解出了整个结构的衍射效率。计算分析显示,对闪耀角为11.3°、周期为500 nm的金属铝闪耀光栅可以得到高于90%的衍射效率和相应的闪耀级次。实验表明这种矢量衍射数值算法具有较高的准确性,可以推广应用于高致密刻线复杂光栅的衍射计算分析。