Structure distortion,optical and electrical properties of ZnO thin films co-doped with Al and Sb by sol-gel spin coating

ZnO thin films co-doped with Al and Sb with different concentrations and a fixed molar ratio of AlCl 3 to SbCl 3 at 1:2, are prepared by a sol-gel spin-coating method on glass annealed at 550°C for 2 h in air. The x-ray diffraction results confirm that the ZnO thin films co-doped with Al and Sb are of wurtzite hexagonal ZnO with a very small distortion, and the biaxial stresses are 1.03×10 8 , 3.26×10 8 , 5.23×10 8 , and 6.97×10 8 Pa, corresponding to those of the ZnO thin films co-doped with Al and Sb in concentrations of 1.5, 3.0, 4.5, 6.0 at% respectively. The optical properties reveal that the ZnO thin films co-doped with Al and Sb have obviously enhanced transmittance in the visible region. The electrical properties show that ZnO thin film co-doped with Al and Sb in a concentration of 1.5 at% has a lowest resistivity of 2.5Ω·cm.     

Structure distortion, optical and electrical properties of ZnO thin films co-doped with Al and Sb by so--gel spin coating

ZnO thin films co-doped with Al and Sb with different concentrations and a fixed molar ratio of AlCl₃ to SbCl₃ at 1:2, are prepared by a sol--gel spin-coating method on glass annealed at 550 ℃ for 2 h in air. The x-ray diffraction results confirm that the ZnO thin films co-doped with Al and Sb are of wurtzite hexagonal ZnO with a very small distortion, and the biaxial stresses are 1.03×10⁸, 3.26×10⁸, 5.23×10⁸, and 6.97×10⁸ Pa, corresponding to those of the ZnO thin films co-doped with Al and Sb in concentrations of 1.5, 3.0, 4.5, 6.0 at% respectively. The optical properties reveal that the ZnO thin films co-doped with Al and Sb have obviously enhanced transmittance in the visible region. The electrical properties show that ZnO thin film co-doped with Al and Sb in a concentration of 1.5 at% has a lowest resistivity of 2.5Ω·cm.     

Effects of doping concentration on properties of Mn-doped ZnO thin films

This paper reports that the radio frequency magnetron sputtering is used to fabricate ZnO and Mn-doped ZnO thin films on glass substrates at 500~°C. The Mn-doped ZnO thin films present wurtzite structure of ZnO and have a smoother surface, better conductivity but no ferromagnetism. The x-ray photoelectron spectroscopy results show that the binding energy of Mn_2p3 / 2 increases with increasing Mn content slightly, and the state of Mn in the Mn-doped ZnO thin films is divalent. The chemisorbed oxygen in the Mn-doped ZnO thin films increases with increasing Mn doping concentration. The photoluminescence spectra of ZnO and Mn-doped ZnO thin films have a similar ultraviolet emission. The yellow green emissions of 4~wt.% and 10~wt.% Mn-doped thin films are quenched, whereas the yellow green emission occurs because of abundant oxygen vacancies in the Mn-doped ZnO thin films after 20~wt.% Mn doping. Compared with pure ZnO thin film, the bandgap of the Mn-doped ZnO thin films increases with increasing Mn content.     

Effects of annealing rate and morphology of sol–gel derived ZnO on the performance of inverted polymer solar cells

The effects of annealing rate and morphology of sol–gel derived zinc oxide(ZnO)thin films on the performance of inverted polymer solar cells(IPSCs)are investigated.ZnO films with different morphologies are prepared at different annealing rates and used as the electron transport layers in IPSCs.The undulating morphologies of ZnO films fabricated at annealing rates of 10 C/min and 3 C/min each possess a rougher surface than that of the ZnO film fabricated at a fast annealing rate of 50 C/min.The ZnO films are characterized by atomic force microscopy(AFM),optical transmittance measurements,and simulation.The results indicate that the ZnO film formed at 3 C/min possesses a good-quality contact area with the active layer.Combined with a moderate light-scattering,the resulting device shows a 16%improvement in power conversion efficiency compared with that of the rapidly annealed ZnO film device.     

Effect of Sb-doping on the morphology and dielectric properties of chrysanthemum-like ZnO nanowire clusters

Chrysanthemum-like ZnO nanowire clusters with different Sb-doping concentrations were prepared using a hydrothermal process. The microstructures, morphologies, and dielectric properties of the as-prepared products were characterized by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), field emission environment scanning electron microscope (FEESEM), and microwave vector network analyzer respectively. The results indicate that the as-prepared products are Sb-doped ZnO single crystallines with a hexagonal wurtzite structure, the flower bud saturation degree F d is obviously different from that of the pure ZnO nanowire clusters, the good dielectric loss property is found in Sb-doped ZnO products with low density, and the dielectric loss tangent tanδ e increases with the increase of the Sb-doping concentration in a certain concentration range.     

Effect of Different Substrate Temperature on Phosphorus-Doped ZnO Thin Films Prepared by PLD on Sapphire Substrates

Phosphorus-doped ZnO （ZnO：P） thin films are deposited on a c-plane sapphire in oxygen at 350℃, 450℃, 550℃ and 650℃, respectively, by pulsed laser deposition （PLD）, then all the ZnO：P samples are annealed at 650℃ in oxygen with a pressure of 1 × 10^5 Pa. X-ray diffraction measurements indicate that the crystalline quality of the ZnO：P thin films is improved with the increasing substrate temperature from 350℃ to 550℃. With a further increase of the deposition temperature, the crystalline quality of the ZnO：P sample is degraded. The measurements of low-temperature photoluminescence spectra demonstrate that the samples deposited at the substrate temperatures of 350℃ and 450℃ show a strong acceptor-bound exciton （A^0X） emission. The electrical properties of ZnO：P films strongly depend on the deposition temperature. The ZnO：P samples deposited at 350℃ and 450℃ exhibit p-type conductivity. The p-type ZnO：P film deposited at 450℃ shows a resistivity of 1.846Ω·cm and a relatively high hole concentration of 5.100 × 10^17 cm^-3 at room temperature.     

Characterization of Undoped and Cu-Doped ZnO Thin Films Deposited on Glass Substrates by Spray Pyrolysis

Undoped and copper doped zinc oxide （ZnO） thin films have been prepared on glass substrates by spray pyrolysis technique. The films were doped with copper using the direct method by addition of a copper salt （CuCl2） in the spray solution of ZnO. Variation of structural, electrical, optical and thermoluminescence （TL） properties with doping concentrations is investigated in detail.     

Influence of Concentration of Vanadium in Zinc Oxide on Structural and Optical Properties with Lower Concentration

ZnO films doped with different vanadium concentrations are deposited onto glass substrates by dc reactive magnetron sputtering using a zinc target doped with vanadium. The vanadium concentrations are examined by energy dispersive spectroscopy （EDS） and the charge state of vanadium in ZnO thin films is characterized by x-ray photoelectron spectroscopy. The results of x-ray diffraction （XRD） show that all the films have a wurtzite structure and grow mainly in the c-axis orientation. The grain size and residual stress in the deposited films are estimated by fitting the XRD results. The optical properties of the films are studied by measuring the transmittance. The optical constants （refractive index and extinction coefficient） and the film thickness are obtained by fitting the transmittance. All the results are discussed in relation with the doping of the vanadium.     

Effect of Different Substrate Temperature on Sb-Doped ZnO Thin Films Prepared by Pulsed Laser Deposition on Sapphire Substrates

Sb-doped ZnO thin films are deposited on c-plane sapphire substrates by pulsed laser deposition. Hall results indicate that the conductivity of the Sb-doped ZnO thin films is strongly dependent on the substrate temperature. The sample deposited at the temperature of 550°C exhibits p-type conductivity. It gives a resistivity of 15.25Ω＆#12539;cm, with a Hall mobility of 1.79cm2V-1s-1 and a carrier concentration of 2.290×1017cm-3 at room temperature. The x-ray diffraction indicates that the Sb-doped ZnO thin films deposited in the range of 450-650°C are high c-axis oriented. Low-temperature photoluminescence spectra indicate that the sample deposited at 550°C shows the strong acceptor-bound exciton （A0X） emission.     

Linear and nonlinear optical properties of Sb-doped GeSe_2 thin films

Sb-doped Ge Se2 chalcogenide thin films are prepared by the magnetron co-sputtering method.The linear optical properties of as-deposited films are derived by analyzing transmission spectra.The refractive index rises and the optical band gap decreases from 2.08 e V to 1.41 e V with increasing the Sb content.X-ray photoelectron spectra further confirm the formation of a covalent Sb–Se bond.The third-order nonlinear optical properties of thin films are investigated under femtosecond laser excitation at 800 nm.The results show that the third-order nonlinear optical properties are enhanced with increasing the concentration of Sb.The nonlinear refraction indices of these thin films are measured to be on the order of 10-18m2/W with a positive sign and the nonlinear absorption coefficients are obtained to be on the order of 10-10m/W.These excellent properties indicate that Sb-doped Ge–Se films have a good prospect in the applications of nonlinear optical devices.     

Synthesis of PS colloidal crystal templates and ordered ZnO porous thin films by dip-drawing method

Polystyrene spheres (PS) were synthesized by an emulsifier-free emulsion polymerization technique and the PS colloidal crystal templates were assembled orderly on clean glass substrates by dip-drawing method from emulsion of PS. Porous ZnO thin films were prepared by filling the ZnO sol into the spaces among the close-packed PS templates and then annealing to remove the PS templates. The effects of ZnO precursor sol concentration and dipping time in sol on the porous structure of the thin films were studied. The results showed an ordered ZnO porous thin film with designed pore size that depended on the sol concentration and PS size could be obtained. And the shrinkage of pore diameter was about 30-43%. X-ray diffraction (XRD) spectra indicated the thin film was wurtzite structure. The transmittance spectrum showed that optical transmittance decreased with the decrease of wavelength, but kept above 80% optical transmittances beyond the wavelength of 550 nm. Optical band gap of the porous ZnO thin film (fired at 500 °C) was 3.22 eV.     

Effect of dopants on the structural,optical and electrical properties of sol–gel derived ZnO semiconductor thin films

Undoped, Ga-, In-, Zr-, and Sn-doped ZnO transparent semiconductor thin films were deposited on alkali-free glasses by sol–gel method. 2-methoxyethanol (2-ME) and diethanolamine (DEA) were chosen as a solvent and a stabilizer, respectively. The doping concentration was maintained at 2 at.% in the impurity doping precursor solutions. The effects of different dopants on the structural, optical, and electrical properties of ZnO thin films were investigated. XRD results show that all annealed ZnO-based thin films had a hexagonal (wurtzite) structure. ZnO thin films doped with impurity elements obviously improved the surface flatness and enhanced the optical transmittance. All impurity doped ZnO thin films showed high transparency in the visible range (>91%). The Ga- and In- doped ZnO thin films exhibited higher Hall mobility and lower resistivity than did the undoped ZnO thin film.     

Influence of annealing temperature on optical properties of zinc oxide thin films analyzed by spectroscopic ellipsometry method

Zinc oxide (ZnO) thin films were sol–gel spin coated on glass substrates, annealed at various temperatures 300 °C, 400 °C and 500 °C and characterized by spectroscopic ellipsometry method. The optical properties of the films such as transmittance, refractive index, extinction coefficient, dielectric constant and optical band gap energy were determined from ellipsometric data recorded over the spectral range of 300–800 nm. The effect of annealing temperature in air on optical properties of the sol–gel derived ZnO thin films was studied. The transmission values of the annealed films were about 65% within the visible range. The optical band gap of the ZnO thin films were measured between 3.25 eV and 3.45 eV. Also the dispersion parameters such as single oscillator energy and dispersive energy were determined from the transmittance graph using the Wemple and DiDomenico model.     

Effect of annealing on the structural, optical and electrical properties of ZnO thin films by spray pyrolysis

Zinc oxide thin films have been deposited on glass substrates at a substrate temperature of 673 K by spray pyrolysis. The samples are annealed in ambient atmosphere at various temperatures. The effect of annealing on structural, electrical, and optical properties of ZnO films has been investigated. X-ray diffraction patterns show that crystallinity of the ZnO films has been improved after annealing. The morphology of ZnO thin films is studied by atomic force microscopy. The tensile strain (compressive stress) is found to decrease with increase in annealing temperature which indicates the relaxation of tensile strain in ZnO thin films. A decrease in energy band gap is observed with increase of annealing temperature. The mechanism of blue-green luminescence of ZnO thin film has been analyzed. The resistivity is found to decrease with annealing temperature.     

Development of a novel high speed (electron-mobility) epi-n-ZnO thin films by L-MBE for III–V opto-electronic devices

Intrinsic epitaxial zinc oxide (epi-ZnO) thin films were grown by laser-molecular beam epitaxy (L-MBE), i.e., pulsed laser deposition (PLD) technique using Johnson Matthey “specpure”-grade ZnO pellets. The effects of substrate temperatures on ZnO thin film growth, electrical conductivity (σ), mobility (μ) and carrier concentration (n) were studied. As well as the feasibility of developing high quality conducting oxide thin films was also studied simultaneously. The highest conductivity was found for optimized epi-ZnO thin films is σ=0.06×10³ ohm⁻¹ cm⁻¹ (n-type) (which is almost at the edge of semiconductivity range), carrier density n=0.316×10¹⁹ cm⁻³ and mobility μ=98 cm²/V s. The electrical studies further confirmed the semiconductor characteristics of epi-n-ZnO thin films. The relationship between the optical and electrical properties were also graphically enumerated. The electrical parameter values for the films were calculated, graphically enumerated and tabulated. As a novelty point of view, we have concluded that without doping and annealing, we have obtained optimum electrical conductivity with high optical transparency (95%) for as deposited ZnO thin films using PLD. Also, this is the first time that we have applied PLD made ZnO thin films to iso-, hetero-semiconductor–insulator–semiconductor (SIS) type solar cells as transparent conducting oxide (TCO) window layer. We hope that surely these data be helpful either as a scientific or technical basis in the semiconductor processing.     

氢退火对LPCVD生长的ZnO薄膜光学和电学性能的影响

采用低压化学气相沉积(LPCVD)在玻璃衬底上制备了B掺杂ZnO(BZO)薄膜,研究了氢气气氛退火对BZO薄膜光学性能和电学性能的影响。结果表明:在氢气气氛下退火后,BZO薄膜的物相结构和透光率基本无变化,但BZO薄膜的导电能力却明显提高。Hall测试结果表明:在氢气下退火时载流子浓度基本保持不变,但迁移率却明显提高。实验结果可为进一步提高BZO薄膜的光学电学综合性能提供借鉴。     

Effect of aging time of ZnO sol on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method and the effect of aging time of ZnO sol on the structural and optical properties of the films was studied. The structural characteristics of the samples were analyzed by an atomic force microscope and an X-ray diffractometer. The optical properties were studied by a UV-vis spectrophotometer and a fluorophotometer. The results show that the ZnO thin film prepared by the as-synthesized ZnO sol had relatively poor crystalline quality, low optical transmittance in the visible range and relatively weak ultraviolet emission performance. After the as-synthesized ZnO sol was aged for 24 h, the degree of the preferred crystal orientation along the c-axis of the ZnO thin film prepared by this aged sol was improved. At the same time, this film had a very smooth surface with uniform grains and both its visible range transmittance and ultraviolet emission intensity were obviously increased. These results suggest that appropriate aging of ZnO sol is very important for the improvement of structural and optical quality of ZnO thin films derived from sol-gel method.     

Temperature-dependent luminescence dynamics for ZnO thin films

The paper presents the photoluminescence investigation of zinc oxide thin films. A high quality ZnO films fabricated by dip-coating (sol–gel) method were grown on quartz wafers. The films with different thickness (number of layers) were annealed at different temperatures after the preparation process. It was found that high quality, transparent ZnO thin films could be produced on quartz substrates at relatively low annealing temperature (450–550  $^{\circ }\mathrm{C}$ ). The dependence of the ZnO thin film quality was studied by X-ray diffraction and atomic force microscopy techniques. Optical properties were investigated by classic and time-resolved photoluminescence (TRPL) measurements. Photoluminescence spectra allowed us to estimate energy of the free excitons, bond excitons and their longitudinal optical (LO) phonon replicas as a function of the annealing temperature. An innovative TRPL technique let us precisely measure the decay time of the free- and bond excitons’ in the real time. TRPL measurements as a function of temperature reveal a biexponential decay behavior with typical free/bound exciton decay constants of 970/5310 ps for the as-grown sample and 1380/5980 ps after annealing process. Presented spectra confirm high structural and optical quality of investigated films. We proved that the thermal treatment improve both optical and structural quality and extend the photoluminescence’s lifetimes. The obtained experimental results are important for identification of exciton’s peaks and their LO phonon replicas for the investigated ZnO films.     

The influence of annealing on the properties of ZnO:Al layers obtained by RF magnetron sputtering

Al doped ZnO has been explored as a viable alternative to indium thin oxide, which is usually used as transparent electrodes' coverage but is expensive. Homogenous and durable ZnO:Al layers on glass have been obtained in radio frequency magnetron sputtering system by adjusting optimized deposition parameters, using ZnO ceramic target with 2?wt% Al₂O₃. Then, after growth process, annealing treatment has been introduced in order to improve the quality of the layers. Structural, electrical and optical properties of the obtained ZnO:Al layers are presented and discussed. From the application point of view, the best results (sheet resistance of 24 Ω/sq and transparency well above 85%) were achieved after annealing in 300?°C.